Search Documents

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

By K. L. Cashdollar, C. K. Man, J. R. Gibbins

Oxyfuel combustion is currently one of the principal technological options being considered for capturing carbon dioxide from pulverised coal power plants. In oxyfuel combustion, coal is burnt in a mixture of recycled flue gases and added oxygen instead of in air. In principle this yields a flue gas containing only carbon dioxide, water vapour and small amounts other impurities. Oxyfuel combustion is superficially similar to combustion in air, but there are inevitable differences. This paper describes ignition tests on pulverised coal suspensions using a suite of coals of different rank and from different countries of origin and over a range of oxygen and coal concentrations of interest for oxyfuel combustion. The ignition tests were carried out using the National Institute for Occupational Safety and Health (NIOSH) 20-litre explosion chamber. The purpose was to determine how easily the various coals ignite and burn in mixtures of O2 and CO2 compared to their combustion in air. The residual char volatile and ash contents for the ignition residues were measured using a thermogravimetric analyser (TGA), allowing Q factors (i.e., enhancement in apparent volatile yield due to higher heating rates and/or heterogeneous reactions) to be determined and compared. An ignition index has been derived from the explosion and char data. This index has been used to rank low volatile coals for ignition propensity in air. The results show that to obtain ignition and combustion comparable to that in air, the oxyfuel O2-CO2 gas mixture must contain over 30% O2. Keywords: CO2 capture, combustion, pyrolysis, oxyfuel.

By Sidney Katell

Covering the period from January 1961 through December 1961, this report is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. It is also the third report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related facilities, came from the following sources: 1. A.A.C.E. Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigation. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Industrial and Engineering Chemistry. 11. Nucleonics 12. Oil and Gas Journal. 13. Petroleum Engineer for Management. 14. Petroleum Refiner. 15. World Oil.

Jan 1, 1962

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

By Ronald Althouse

During the past five years under contract with the U. S. Bureau of Mines (BOM Contract J0308002). West Virginia University's Mining Extension Service (WVU-MES) has designed, developed) and delivered to the mining industry a comprehensive training program for Mine Rescue (MR) teams and a management planning tool for Mine Emergency Preparedness. The Mine Rescue team program is systematically built on a set of training objectives, backed up by content, allowing mine operators to conduct team training activities. These materials are user-ready, provide the MR principles and practices for both initial and advanced training, and supply teams with exercises geared to problem-solving activities. In addition to an instructor's program guide, the eight (8) modules that comprise the initial (20 hour) MR training are: an Introduction to Mine Rescue, an Introduction to Self-Contained Breathing Apparatus (SCBA), a set of modules covering each approved minimum 2-hour SCBA (i.e.) the Draeger BO 174-A. the McCaa) the Aerolox. & the Scott Rescue-Pak), and a manual on Auxiliary Apparatus as well as the Chemox Auxiliary SCBA. Advanced, annual refresher training (40 hour) is covered by seven (7) modules that spell-out the principles and practices needed to establish surface organization, to handle mine gases as well as mine ventilation, to conduct exploration, for fires, firefighting, and explosions, to rescue survivors and recover bodies, and to accomplish a mine recovery. Approved by MSHA in 1984 to meet requirements for 30 CFO. Part 49, these materials provide a basis for trainers' instruction, for comparison of team capabilities, for modifying programs resources, and services, and for program planning. The Mine Emergency Preparedness Program (MEPP) is used by management as a tool in the preparation of company personnel for handling a mine emergency operation. As a wholly new program. MEPP depends upon development of a Mine Emergency Organization and Emergency Operations Procedures. It also requires regular scheduling of drills) periodic mock emergencies, and evaluation of organizational responses and program performance beyond required training of mine rescue teams. MEPP materials are arranged into three sets of guides: 1) the Preparedness Program System Guides include an Executive Summary, a Program Director's Guide Mine Emergency Organization, and Emergency Operations Procedures; 2) the Emergency Organization (MEO) User's Guides cover the Rescue and Advisory Division, the Technical/Safeguarding Division, and the Surface Support Division; and 3) the Emergency Procedures (EOPS) User's Guides detail Containment Level Procedures, Notification Level Procedures. Mobilization Level Procedures, and Deployment Level Procedures.

Jan 1, 1986

By B. J. Moore

This publication contains analyses and related source data for 191 natural gas samples from 22 states and 1 foreign country. Of the total samples, 182 were collected during calendar year 1987. The remainder were collected earlier, but releases granting permission to publish were not received before 1987. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1988

By P. D. Laverty

This report describes a processing method developed by the U.S. Bureau of Mines to produce high-quality flake graphite from the steelmaking waste known as kish. The kish produced by current steelmaking practices is a mixture of graphite, desulfurization slag, and iron that is skimmed from the molten iron feed to the basic oxygen furnace. It is estimated that the graphite content of kish discarded by U.S. steel plants is more than sufficient to meet the total U.S. demand for flake graphite. That need is now filled by natural graphite from foreign sources. Kish was treated by a combination of screening and hydraulic classification to produce a concentrate containing greater than 70 pct graphite. Leaching of the concentrate with hydrochloric acid solution gave a graphite product with 95-pct purity. An optional secondary leaching operation with hydrofluoric acid produced graphite with a purity of 98 pet or greater. The flake size of graphite from kish ranged from 10 mesh down. Evaluation of test samples by industrial graphite users indicated that kish graphite is a suitable substitute for the natural material for most uses. A process flowsheet and material balance for pilot plant design are presented.

Jan 1, 2010

By Gary M. Larwood

A study was conducted to determine the amount of transportation equipment required to move 1.2 billion tons of coal in 1985. The Federal Bureau of Mines has investigated a majority of the various practices associated with coal transportation and has gathered information on the regional origin-destination patterns, methods of movement, equipment stocks, rate structures, and operational capacities of the most important modes of coal haulage currently in use. Models employing this information were developed to establish the origin-destination pattern for 1985 coal shipments, estimate practical tonnage capacities for selected coal hauling rivers, develop modal shares for both unconstrained (by river capacity) and constrained cases, and present a range of coal transportation equipment requirements for given sets of constraints. Projected transportation shares for rail ranged from 63.7 to 72.3 percent, and for river, from 8.8 to 16.4 percent. Other coal transportation modes (truck, conveyor, Great Lakes, and tidewater) are expected to retain their historic shares of coal traffic. Equipment estimates were made for 1985 rail and water transportation based on 1973 average and best practice. Average practice estimates ranged from 675,000 to 710,000 hopper cars (100-ton) and 3,100 to 5,940 barges (1,400-ton equivalent). Best practice estimates ranged from 126,000 to 142,000 hopper cars and 1,750 to 3,450 barges. Full implementation of 1973 best practice by 1985 is unlikely.

Jan 1, 1976

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

By F. E. Armstrong

This Bureau of Mines publication reviews 237 papery on radiometric prospecting, which is the measurement of naturally occurring radioactivity in the earth's surface and its application to petroleum and natural gas exploration. Many theories and documented surveys are listed in both support and refutation of this reported phenomenon, and the Bureau of Mines is conducting research to obtain direct field information in order to determine the statistical credibility of a radiometric method of predicting petroleum accumulation.

Jan 1, 1973

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and laboratory testing of dust collectors for use on double drum shearers. Systems tested included: ? High Capacity Flooded Bed Scrubber ? Water Powered Extraction Cowls ? Water Powered Extraction Drums ? Water Powered spot Scrubbers. The systems were tested using tracer gas in a full-scale model of a longwall shearer face. This report provides a detailed description of the test facility, test methods, and system test results.

Jan 1, 1982

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By Parviz F. Rad

This Bureau of Mines report reviews laboratory and in-mine techniques for determining mechanical properties of coals, with special emphasis on the relationship between these properties and the minability of coal. An extensive bibliography is included.

Jan 1, 1973

In 2007, a total of 725 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Nonmetal mines com-prised 4.9% of all m ining operations. ? Mines producing common clay comprised 25.4% (n=184) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the U.S. Virgin Islands.

Aug 1, 2009

By T. Mal

A test system was developed at the National Institute for Occupational Safety and Health's ventilation test gallery for measuring airflow using a three-axis ultrasonic anemometer. The gallery war used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data, collected at multiple sampling locations between the face and the end of the curtain, were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations and displayed as methane distributions in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within 0.6 m (2ft) of the face.

By H. C. Miller

For nearly a score of years the American petroleum industry has faced the problem of maintaining its economic structure while oil -producing potentialities greatly exceeded the increasing market demand for oil and its products . However , the combination of maximum civilian demand with rising defense requirements caused an all - time peak in crudeoil production in the latter half of 1941 , with a daily production (as estimated by the Bureau of Mines ) of 4,139,000 barrels in December - an increase of 16 percent over the daily production of 3,573,000 barrels in December 1940. In the event of a long war , a continuing , steady, and adequate supply of petroleum and its products for military and required civilian needs is essential, and the efficiency of recovery of oil from natural underground reservoirs will have to be maximum. Whereas it may not be possible to increase production in some fields , the output from others may have to be drawn at a much faster rate than formerly . More than 10 years ' experience in operating oil fields under proration control has demonstrated to petroleum engineers that some of the efficiency of recovery of oil from reservoir sands and rocks is sacrificed if the oil and gas are withdrawn at too . rapid a rate . As petroleum is an irreplaceable natural resource for which suitable substitutes probably will not be available in desired quantities for many years , any producing method that jeopardizes the quantity of oil that may be recovered from underground reservoirs must be considered at this time of declared war against aggressor nations as conflicting with the best interests of national defense . At best, the efficient recovery of oil is a complex problem . It involves not only a knowledge and application of the fundamentals of fluid flow through porous mediums, but the sources of energy responsible for the movement of oil and gas through reservoir sands and porous rocks to wells must be known to determine the best practices for extracting these hydrocarbons . Reservoir energy is of two kinds - (1 ) water under hydrostatic head underlying the oil in the extraneous parts of the reservoir system and ( 2 ) natural gas under pressure as "free " gas in the reservoir or in solution in the oil . Inasmuch as the efficiency of oil recovery depends largely on the manner in which reservoir energy is used to move oil through reservoir sands and porous rocks to wells , optimum practices for withdrawing the oil cannot be determined until it has been established that the oil in the reservoirs is being forced to wells by an internal gas expansion, by a natural water drive , or by a combination of gas expansion and water drive . There is a fundamental difference in the performance characteristics of gas - expansion and water - drive reservoirs . In a strictly gas - expansion reservoir the energy available to move oil and gas through the porous formations to wells results solely from gas pressure , which is maximum when the reservoir is tapped by the first well . Pressures decline as oil and gas are withdrawn ; consequently, the energy available for moving oil and gas through the oil - bearing formations to wells decreases with production . Curtailing the oil - production rate or shutting in gas - expansion reservoirs entirely will not act to replenish energy previously used in the production of oil and gas ; in their operation , therefore , it is especially important not to waste reservoir energy - the production of oil with high gas : oil ratios will be reflected in lower ultimate recoveries of oil .

Apr 1, 1942

By Jonathan S. Kelly

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and the underground evaluation of ventilated cutting drums, on a double ended ranging drum shearer. The ventilated drum uses high pressure (1,500 psi) water sprays to draw air (3,500 cfm) through 12 airmoving tubes mounted in the drum hub. The sprays draw dusty air from the face side of the drum, scrub the air, and discharge the clean air on the gob side of the drum against a deflector plate. During a three week underground evaluation, the cutting drums reduced shearer generated dust levels at the shearer operators position by 40%, at the shield operators downwind of the shearer by 55%, and at the tailgate by 55%. Cutting and loading performance of the drums were superior to the mine?s conventional drums. After the evaluation, the mine continued to use the ventilated drums to finish mining the panel. During this 3 month period, there were no mechanical or seal failures demonstrating excellent system reliability.

Jan 1, 1987

By H. N. Dunning

A comprehensive production research program, now in progress at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville, Okla., includes studies of the displacement of petroleum from sand by detergent solutions. An earlier report (12)2/ presented the results of an extensive research program to determine the value of detergents as floodwater additives. This report presents later results of the detergent-testing program (13, 17). Although water-flooding methods and controls are constantly being improved to increase the production of oil from secondary-recovery operations, considerable crude oil commonly remains.in place after a water flood has been terminated. Therefore, the possibility of improving the efficiency of a waterflood by the use of detergents is of increasing interest. The effects of many substances on the efficiency of water flooding have been investigated in laboratory studies (5, 11, 13, 17, 19, 24). Of the various sub-stances tested, only surface-active agents were consistently effective in removing oil from sand. Results of laboratory studies presented in earlier reports (9, 11, 12, 13) show that many detergent solutions effectively displace petroleum from sand surfaces under varying conditions encountered in centrifuging, manual and mechanical agitation, ultrasonic vibration, and imbibition.

Jan 1, 1957

By Forrest T. Moyer

Injury experience at metal mines and mills (excluding officeworkers) in 1964 was 60 fatal and 3,672 nonfatal disabling work injuries during an exposure time of 149 million man-hours worked. These injuries occurred at a frequency rate of 24.57 per million man-hours and had a severity rate of 3,687 days lost or charged per million man-hours. Employment at 2,363 metal mines and 291 mills, excluding officeworkers, was 68,140 men in 1964. The average number of days worked was 274 The principal cause of fatal injuries at all mines and mills was haulage accidents and in underground mines, only, was falls of ground. The principal cause of nonfatal injuries was handling material accidents. The frequency rate at metal mines and mills in 1964 was slightly below that of 1963, whereas the severity rate was higher. Injury experience at 94 primary nonferrous smelters, refineries, and reduction plants (excluding officeworkers) was 8 fatal and 999 nonfatal disabling work injuries during a worktime of 98 million man-hours worked. The combined injury-frequency rate in 1964 was 10.29 and the injury-severity rate was 1,005. The 36,956 employees worked an average of 329 days during 1964. The principal cause of injuries at these plants was handling material accidents.

Jan 1, 1968