Search Documents

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By Robert K. Guthrie, James W. Amyx, D. B. Taliaferro

"INTRODUCTION Secondary recovery of oil by water-flooding is practiced more extensively in North Texas than in any other section of the State, and the progress and experience of the operations in that area are of continuing interest to all branches of the oil industry. The first Bureau of Mines report on water flooding in North Texas 7/ chronicled the activities from December 7, 193f', when the Railroad Commission of Texas granted The Texas Co. the first permit to inject water into an oil-bearing sand, through 1944. This second report has been prepared as a supplement to Report of Investigations 3906 to show the progress and expansion of water-flooding. The format of this report is almost identical with what of report of Investigations 3906, except for a few miner changes. For the sake of brevity, certain basic information contained on the first report has not been repealed, and the reader is urged to consider the two reports as corporation writings.The North Texas area, as encompassed by the two reports, corresponds Railroad Commission of Texas Districts 7P and 9. Oil-development operations in the two districts, since oil was discovered in 1904, have resulted in the recovery of approximately 1,400,000,000 barrels of oil from a proved area that has been estimated to exceed 413,000 acres. During October barrels of oil was produces by primary and secondary-recovery methods from 1,746 flowing wells and 25,211 pumping wells, a daily average 6.6 barrels per well. Of this total volume of oil recovered in October 1947, 47,965 barrels (0.87 percent) was recovered from leases on which water-flooding operations were in progresses."

Feb 1, 1948

By T. N. Rushton

Rate minima are encountered in the reduction of magnetite with hydrogen. In a certain temperature zone, the reaction rate decreases with rise in temperature. This is inexplicable by classical kinetic theories; neither is a transition in reduction mechanism suitable for interpreting the observed behavior, This anomaly can be fully explained by hypothesizing two species of chemisorbed hydrogen with different adsorption coefficients and activation energies for adsorption. Competition between two energetic states of adsorption occurs with temperature rise, with the low energy state predominating below the anomalous temperature zone and the high energy state above it. The presence of two possible adsorption sites appears to be characteristic for oxidic adsorbents.

Jan 1, 1968

By E. A. Ziemba

The modified in-situ process is one of the methods being considered for extracting oil from oil shale. One of the questions to be answered for this approach is the environmental consequence of underground retort abandonment. This report outlines a study which addresses the question in terms of a grouting solution. It covers the development of a spent shale ash based grout which will fulfill the environmental requirements in terms of strength, stability, and impermeability. In addition, it will allow the reinjection of up to 50 percent of material mined and surface retorted as part of this process.

Jan 1, 1982

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

By J. E. Hamak

This publication contains analyses and related source data for 151 natural gas samples from 19 States. Of the total samples, 138 were collected calendar year 1989. The remainder were collected earlier, but releases to were not received until 1989. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1990

By F. N. Kissell, C. M. McCulloch, Maurice Deul, J. R. Levine

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas content of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and desorbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

By Donald F. Reed

Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasechatch and Weewoka, both in the; vicinity of Wintorboro, 50 miles east of Birmingham. The deposits were investigated by the Bureau of Mines in 1945 and 1944. Approximately 15,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.

Jan 1, 1949

By Pedro Lilienfeld

This report describes the development, design, fabrication and testing of a port-able, battery-operated, light scattering monitor (henceforth to be designated as ILSDM) for the rapid measurement of the concentration of respirable dust in mining environments. This instrument incorporates state-of-the-art design characteristics and makes use of advanced solid-state components both for light emission as well as for its detection. The use of a pulsed light source combined with synchronous signal detection minimizes drift problems and optimizes the sensitivity of the measurement. Simplicity of operation, reliability and ruggedness, light weight as well as improved performance were salient objectives of this instrument development program. Continuous clean-air flow screening of all critical optical surfaces, and optimized optical detection and electronic signal processing design resulted in about a hundred-fold decrease of noise and drift with respect to precursor instruments. Equivalent mass concentration measurements 88 low as 10 micrograms per cubic meter can be routinely performed with time constants of about 2 second.

Jan 1, 1979

By Michael J. Sapko, William D. Monaghan, Michael A. Trevits

Mine seals are used extensively in underground coal mines to segregate mined-out areas and to isolate fire zones or underground areas that are susceptible to spontaneous combustion. Over the years, 30,000 mine seals have been erected in underground coal mines in the United States. Mine seals, along with rock dusting and ventilation, represent the fundamental means of preventing underground coal mine explosions. In this study the National Institute for Occupational Safety and Health (NIOSH) used ground penetrating radar (GPR) technology to determine if each of three test mine seals were uniformly constructed. Three mine seals representing different construction methods and materials (cast-in-place foamed cement; solid block, polyurethane foam and gravel; and wire mesh, rebar and gunite) were erected at the NIOSH Lake Lynn Laboratory’s underground mine as part of an on-going research program. The seals were imaged using GPR with 400-, 500-, 900-, and 1,000-MHz antennas. We found that variations in uniformity existed in the material for the cast-in-place foamed cement seal. Variations in uniformity also existed in the seal made from solid block, polyurethane foam and gravel. The post-processed radar records correlated closely with recovered core samples (areas of gravel and polyurethane foam, and areas containing only polyurethane foam). Finally, the radar records of the seal made of wire mesh, rebar and gunite showed the various components. The results of this work suggest that GPR could be used as a tool to evaluate mine seal characteristics and construction uniformity.

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By E. D. Gordner

Irrespira ble gutses issuing from the rock fofflb tions ere tJ source of expense ond danger in some metGLl mines. There is a great Variation in the compos i-· tion of such gdses and, os shown 'by recent sampling by the Bureau of ines, the gas rr;;,.y consi$t mostly ct carbon dioxide, (Rocle Strata Gtsses in the Mines of the East Tintic Mining District, by G. E. McElroy, Bu.retau of Mines Serial 2Z75) or f methone (Metruine in Ccalifornia C.old Mines, by B. 0. Picl-Q:lrd i:lnd !.. D. ("iordner, Bure, cf Mines Serial 2303), or nitrogen, sin the present instonce. A nl.liilber of unventilated rt:t.ises in some of the mine of l:l Neva&. district conuin «i'ccumulCltions of l;i hih-nitrogen gas the1t will not supi:ort life or combus­tion. The rdises ore in different geologiecil formations and in widely sep1:1rated. loecslities in the mining district. One ot" two ri::lises in the sme fc.rtr.ation may be full of the gos cand einother nec-r'by be t'ree ot· it. Lives have been lost t:lnd a number of men heave been overcome on enteing unvetilated rtsises in which their­respircable tss hcsd c1ccuni..1.l1::1ted between sldfts. Gener1:1lly, however, the gas see:ns to noozett from the .t'onrbtio:1 ond to ecc1: .. ,i.-1,;.1:.1te so slowly tMt its presence is not suspected t the tfr.1e, bu.t discovered. ed:'t&.c' the raise is t)band.oned. OcCE.isionelly 1 t issues from a ne•.,ly cut cre·tice or fissure under considerca ble pressure and in lar!?e enough '3.'16ntities to overcome or drive 011t men working in unventilated places.

Dec 1, 1922

By M. Hertzberg

Results of a comprehensive study of the absolute spectral radiance of the infrared emissions from methane-air explosions are reported. The spectral growth of these expanding flames were recorded with a time resolution of 1 msec in the spectral range of 1.7 to 5.0 µm. Time-resolved spectra were obtained for methane-air mixtures as a function of stoichiometry, nitrogen dilution, and Halon dilution, in a 9-liter vessel under different venting conditions. Data are also presented for coal dust-air explosions. Temperatures, obtained from the absolute radiances and from a band ratio technique for methane-air, are internally consistent and are generally 50° to 200°K below adiabatic flame temperatures. All near limit mixtures gave essentially the same flame temperatures (1,500° to 1,600° K) regardless of whether the limit was obtained by dilution with excess air, excess methane, excess nitrogen, or Halon. The coal dust explosion spectrum is essentially a blackbody continuum at 1,500° K with some selective emission at 4.4 µm from hotter CO2. The data are analyzed in terms of the radiative dynamics of a sperically expanding flame zone. The importance of radiative transport is assessed. An equation is derived which relates the instantaneous fraction of combustion power radiated to adiabatic variables.

Jan 1, 1973

By Fermont F. Clarke, Others, Paul Zinner

"INTRODUCTION The Edison mine comprises workings on two irregular spodumene-bearing pegmatite dikes which outcrop near the town of Keystone in the southern portion of the Black Hills of South Dakota. The Bureau of Mines conducted an investigation of the Edison mine as part of a comprehensive study of the lithium mineral-production possibilities in the Black Hills area. The work was undertaken during the Second World War, when the demand for certain lithium salts and compounds exceeded the then small productive capacity of the industry.During the course of the project, the Bureau of Mines completed 13 diamond core-drill holes, aggregating 2,114.5 feet of drilling. Twenty-six cannel samples were taken from the main Edison shaft, and 13 miscellaneous samples were obtained to permit analysis of the efficiency of phases of mining and sorting operations. Metallurgical tests were made by the Bureau of Mines to investigate the feasibility of beneficiating spodumere-bearing ores from the Edison mine. 3/"

Apr 1, 1948

By Steven D. Wirch

Abandoned underground coal mine areas must either be sealed or ventilated to comply with federal mine regulations. Ventilation of these abandoned areas is often impractical due to roof falls and inadequate primary mine ventilation. If the area is sealed, a very complex ventilation system is set up. In which the gob "breathes" in and out due to barometric pressure fluctuations. The Gob Assistant is a computer program (for use on IBM compatible personal computers) which allows the prediction of air flows into and out of a sealed mine area. Gas flows with applicable control techniques are also modeled. This information is presented to the user who will decide which control technique, or combination of techniques will ultimately be applied. The Gob Assistant is an intelligent gob simulator that can reduce the guesswork involved in predicting the effects of sealing and control techniques before they are applied. This paper provides the fundamental principles upon which the Gob Assistant is based, verification of these principles, and an explanation of how these principles were integrated into the Gob Assistant.

Jan 1, 1988

By Lloyd Williams

1. The investigation shows that the Coal Creek has been the most productive, bed in Campbell County and contains the largest recoverable reserves of coal. The Pewee, Red Ash, and Jullico have been relatively productive beds and contain appreciable recoverable reserves of coal. The Blue Gem also has been productive in the past, but available information indicates that most of the remaining coal is Less than 28 inches thick. The Big Mary has relatively large reserves over 28 inches thick, but the coal is high in ash and sulfur. Thick partings in the Windrock bed have discouraged mining in that bed. The Poplar Creek and Rex beds generally are below drainage, and large areas have been excluded from the reserve estimate, Reserves in the Walnut Mountain bed will be difficult to mine due to the irregu¬lar thickness and lack of continuity of the bed. Estimated coal reserves are- small in the remaining five beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-Foot of coal in place, are estimated to be 398 million tons as of January 1, 1953, o? this total, 267 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1956

By O. P. Hood, G. St. J. Perott, S. P. Kinney

"FOREWORD (By O. P. Hood, Chief mechanical engineer).During the war certain suggestions concerning power production were made by Mr. Walter E. Trent to the War Inventions Board, and at the request of the War Department facilities for experimental work were provided on the grounds of the. Bureau of Standards.The experiments were along the line of controlling the conditions of combustion in a closed space. In order to reduce slag troubles, experiments were carried out for removing ash from powdered coal. After the war, work along this line was continued, resulting in the Trent Process, which agitates or beats together powdered coal, water and oil.A new technology had previously been given to ore preparation by the use of small quantities of oil in water with froth flotation, and although the methods, results and mixtures of the Trent Process were quite different, yet the same physical phenomena of differential wetting used, and the possibility of there being interesting results in fuel technologic was evident. A cooperative agreement was entered into, whereby the Bureau of Mines was to investigate the underlying physical and chemical facts and make them public, and the Trent Corporation was to pay the cost of the investigation.The several reports as made have been available to any one interested, and are now to be published. While the Bureau of Mines felt justified in investigating the physical phenomena so far as might be done in a laboratory, and so far as public interest might reach, no attempt was made to discover the commercial possibilities which development might bring. The question of commercial possibilities must be left for commercial enterprise to answer."

Jul 1, 1921

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987