Search Documents

1. Domestic Production and Use: In 1982, 13 companies operated 30 primary aluminum reduction plants, with 3 firms accounting for 55% of production. Washington, Oregon, and Montana accounted for 34% of the production; Texas, Louisiana, Missouri, and Arkansas 18%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central and eastern States 34%. Based on published producer prices, output of primary metal in 1982 was valued at over $5.5 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 39% of domestic consumption in 1982, transportation 20%, building 14%, electrical 8%, consumer durables 8%, and other uses 11%.

Jan 1, 1983

By R. D. Leitch

[The accepted theory of acid formation in coal mines with the subsequent appearance of the acid in coal-mine drainage, is oxidation of iron pyrite and subsequent solution and hydrolysis of the iron sulphate formed. It has also been found that 5 gobbed sections and worked-out areas, where there is usually an abundance of iron pyrite-bearing, materials in contact with air, are the sections that make the most important contribution to the quantity of acid drainage. It would thus seem obvious that if oxygen can be kept out of contact with tae acid-forming materials in tie- sections mentioned the amount of acid in coal-mine drainage could be reduced markedly and corrosion problems with mine pumping equipment and general stream pollution mitigated thereby. Although the efficiency of the suggested remedy as been borne out by laboratory experiments6, it has appeared desirable to substantiate the laboratory work by field observations in so far as pertinent data are available. It has been difficult to learn of mines or sections of mines about to be sealed, whereby an actual comparison of the drainage before and after sealing can be made. In view of that difficulty it has been necessary to devote attention to a comparison of the character of the water from areas already sealed with that from open but otherwise comparable sections of the sane mine. Previous cork has shown that the acidity of drainage in different parts of the same mine may vary, but if it can be shown also that the water from sealed areas is with but fen exceptions less acid than the otherwise similar open sections of tae same mine, the laboratory finding will be supported in a practical gray. This report presents some of the evidence that has been obtained.]

Jan 1, 1930

"Research on the control of exposure to respirable contaminants in mine atmospheres is conducted in five areas; 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The distribution of research findings to the mining industry, to government agencies, and to scientists at other universities is accomplished in several ways.A data bank of respirable dust samples displaying a wide range of characteristics (low volatile, medium volatile, high volatile, silica fireclay, rockdust) has been established by the Center. This data bank is being utilized by Center researchers in a suite of medical, scientific, and engineering tests (FIGURE 26).The Center has honored requests for educational and informational materials from several sources, including MSHA and CANMET who received information on Center generated software and used the Center's expertise in developing a computer program for particle distribution model (DISFIT).The Generic Mineral Technology Center for Respirable Dust has organized two dust conferences on respirable dust, the Coal Mine Dust Conference, held at West VirginiaUniversity, Morgantown, West Virginia from October 8-10, 1984 and Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control, an international symposium on Respirable Dust in the Mineral Industries held at The Pennsylvania State University, University Park, Pennsylvania from October 14-16. 1986. These conferences were co-sponsored by the U.S. Bureau of Mines, Mine Safety and Health Administration, National Institute for Occupational Safety and Health (NIOSH), and the American Conference of Governmental Industrial Hygienists (ACGIH). On August 23-26, 1988, the VIIth International Pnuemoconioses Conference was held in Pittsburgh, Pennsylvania. While not a sponsor of this conference, researchers in the Generic Mineral Technology Center for Respirable Dust had significant participation with sixteen (16) papers presented (see Volume 8 of this series for abstracts and papers). These conferences provided a significant forum for the exchange of ideas on dust research and the interchange of research findings. The proceedings from these conferences are available from NTIS and ACGIH.In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust (FIGURE 27). As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Bureau's Technology News series have been a very effective means of USBM technology transfer. Individual no-cost subscriptions to the Technology News series are available from the U. S. Bureau of Mines, Branch of Technology Transfer, 2401 E Street, N.W., Washington, DC, 20241."

Aug 31, 1989

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By J. A. Kost

A dust-control manual was prepared for use by mine operations personnel. The manual documents state-of-the-art control techniques, dust sampling, and use of personal protective devices. Content addresses advantages/disadvantages of control techniques, design and operating specifications, and implementation and maintenance guidelines. An indexed list of selected references is also included. In addition to the completed manual, this report documents work performed in the course of its preparation.

Jan 1, 1981

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 mil-million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious.

Jan 1, 1934

By Richard F. Link, George S. Koch

Through the use of statistical methods, estimates of metal content and tonnage of an ore body made by using data from 18 diamond-drill holes are compared with actual values established with data from 1,829 drift samples. The reliability of the estimates made from the drill holes is assessed in several ways. The relationship of metal content (assay-width product) to grade is explained. It is concluded that useful estimates can be made from 18 drill holes provided that reasonable assumptions are made and certain risks accepted. The ore body investigated is the Don Tomas vein of the Frisco mine, San Francisco del Oro, Chihuahua, Mexico.

Jan 1, 1964

By F. N. Kissell

The machine-mounted continuous respirable dust monitor (MMCRDM) is a fixed-location area sampling device developed for possible use at the working face of an underground coal mine. This device, based on proprietary technology known as the tapered element oscillating microbalance, has evolved over the past eight years through a cooperative effort of the former Bureau of Mines, MSHA, and the Rupprecht & Patashnick Company in Albany, NY. The capability to measure respirable coal mine dust levels on a continuous basis, rather than depending solely on periodic samples obtained from the traditional coal mine dust samplers, has been a goal in the mining industry for nearly two decades. Recently, an extensive series of laboratory and underground tests was conducted by NIOSH with the cooperation of MSHA and coal operators to test the performance of the MMCRDM In preliminary laboratory testing, the MMCRDM seemed to work well. However, in every underground test, when compared to reference samplers placed close to the inlet, the MMCRDM failed to meet the 25% accuracy criterion specified in the contract under which it was developed. Two reasons explain this failure: First, in most tests the bias (the relative discrepancy between the average MMCRDM concentration and the average reference sampler concentration) was too great. Second, the variability of the samplers used for reference comparison was too large. Finally, the underground testing of the MMCRDMs showed that they are quite unreliable at this stage of development. In the majority of mine tests, no more than 10 shifts of data were taken before the MMCRDM failed to function properly. Major breakdowns, requiring the return of the MMCRDM to the factory for repairs, occurred on average every 28 days. To be considered mine-worthy, MMCRDM reliability must be substantially improved. KEYWORDS Dust, coal dust, dust instrumentation, dust sampling, dust monitoring, black lung, pneumoconiosis

By Walter E. Lewis

A mothod of cutting St. Poter sandstono by streams of water under pressuro from nozzles and pumping the resulting, sand to the surface has roduced the cost of storm-sowor construction in the Minneapolis-St. Paul aroa. The hydraulic tunneling method, has boon in uso since 1934, and it is adaptable only to the lower part of tho St. Potor, sandstone, which lios within or just abovo the ground-wator levol. Tho upper part of the formation, immediately bolow tho Plattoville limestone, 18 comonted and camot bo mined by hydraulic mothods. The tunnel oporation observed in this instance is a main storm sowor starting at tho Mississippi Rivor below the 10th Avenuo SE bridge and will be drivon 6,000 foot at a grado of 1 foot por thousand undor the city of Minneapolis to Konnody and Arthur Stroots NE. A lateral storm sowor, which branchos from the main sovor at 8th Street SE, will oxtond from 10th Avonuo SE to 15th Avonuc SE. Tho tunnele are being drivon with the floor approximately at ground-wator lovol. All waters ontoring the main storm sower vill drain into the Mississippi Rivor. Tho main storm sewer cross soction is excavated to a roughly hox- agonal shapo 10 foot high by 10 foot wido at the contor. The upper half of the tunnol soction is solidly lined with either timber or stool. After all oxcavation is completed, the tunnel will be finished with a concrete circular lining 8 feet in inside diameter. The lateral storm sewer is excavated to a 5-1/2-foot by 7-1/2-foot section and will event- ually be finished with concrete to a modified horseshoe-shaped section 6 feet by 4 feet. Where the back or walls are considered unsafe during excavation, the upper half of the tunnel is lined solidly with timber. The equipment used by the Sower Division, City of Minneapolis, has been selected to meet a number of applications in storm-sewer work with diversified usage in mind. The sand pumps used on this job are rubber-lined, designed to work against a head of 100 foet. Either 4-inch or 6-inch diameter suction and discharge openings may be used. Other equipment, such as pipe, mine rail, flexible hoses, compressors, and general surface shop equipment, is drawn from a contral warohouse. It may be either new or used, depending on what is available at the warehouse. Much of the pipe and mine rail has been used for many years on several different tunnol jobs.

Jul 1, 1950

By George S. Rice

"INTRODUCTION During the past 4 or 5 years the frequent occurrence of bumps in coal mines of the Cumberland field, in Harlan County, Ky., and Wise County, Va., has caused much apprehension among miners and mining officials of that region.These bumps have caused many deaths and injuries, and have been increasing in frequency. Eight men were killed and a number injured by bumps in the first 4 months of 1934. Their unpredictable occurrence and the usual absence of any preliminary warning tremors or sounds, such as ordinarily precede a large fall of roof, cause fear of other bumps and impair the morale of mine workers.Acknowledgments This report on bumps in coal mines of the Cumberland coal field of Kentucky and Virginia is based on an investigation made at the urgent request of .the Harlan County Coal Operators Association, through James F. Bryson, director of safety of the association, to the Director of the United States Bureau of Mines, following a series of disastrous bumps in. Harlan County, Ky., and Wise County, Va. The request was granted and the writer detailed to undertake the investigation, which was made in June 1934.The officials of certain operating companies in the Cumberland field gave every facility for examining the conditions accompanying bumps in their mines. The writer is most grateful to them for the courtesies shown; to J. F. Bryson, to J. F. Davies, district engineer, Safety Division, U. S. Bureau of Mines, who accompanied the writer throughout his trip to the vari¬ous mines and gave him much assistance and detailed information regarding the occurrence of bumps; and to Dr. David White for reviewing the geological descriptions,Definition of Bumps ""Bumps"" are phenomena comparatively rare in the coal fields of the United States and, for that matter, in the coal fields of the world, because for their occurrence certain exceptional natural conditions are required strong, massive strata of sandstone or conglomerate above the coal and a fairly strong floor, as will be described in detail later."

Jan 1, 1935

By William Seymour, L. D. Schmidt

"FOREWORDAmong many problems created by World War II, the question of supplies and distribution of raw materials is of outstanding importance. One of the most critical of these raw materials is fuel, and of the fuels coal is of primary importance. The normal consumption of coal has increased greatly owing to the increased tempo of industry in general. It has been necessary to divert much of the fuel oil, gasoline, etc., ordinarily used for industrial and domestic purposes, to supply the enormous demands of mechanized warfare. Coal must be provided to replace this fuel. Furthermore, the enormous increase in the production of steel has increased the demand for coking coals to a critical point.The Solid Fuels Administration for War is encouraging the use of anthracite fines in the production of byproduct coke for blast furnaces for three reasons. First, the production of anthracite for domestic use; is hampered by the inability to find a market for the fines incidental to the production of domestic sizes. Second, the shortage of low-volatile coking coal is acute, and any action that will decrease the quantity of low-volatile coal required will relieve the situation. As will be seen in this report, there is some promise that use of anthracite fines in coke-oven mixes will lower the amounts of low-volatile coal required. Third, utilization of those anthracite fines will tend also to alleviate the general fuel shortage. It has been the privilege of the Bureau of Mines to cooperate with the Solid Fuels Administration in the technical problems involved."

Apr 1, 1945

By J. B. Salsman

As part of the research effort on investigating the effects of microwave energy on the chemical and physical properties of minerals and ores, the U.S. Bureau of Mines (USBM) Tuscaloosa Research Center has conducted research to measure the dielectric properties of these materials. The objective was to establish a reliable database for use in predicting the effects of microwave heating on a wide range of minerals. The dielectric constants and loss factors of minerals, commonly referred to as the dielectric properties, were determined utilizing the theory of microwave propagation through an open-ended, air-filled coaxial line that was terminated at its open end with the particular mineral under investigation. In this phase of microwave research, the USBM measured the dielectric properties of powdered minerals with medium to high electrical conductivities in the frequency range of 300 MHz to 3 GHz and as a function of temperature from 25 to 325 °C. Since the minerals were prepared as powders, techniques were used to relate the measured dielectric properties of the powdered minerals to the dielectric properties of the mineral at its theoretical or natural density.

Jan 1, 2010

This report is the 24th in a series summarizing research on coal and related investigations3 by the Bureau of Mines. The coal programs of the Bureau of Mines include a wide range of theoretical and applied studies--such as fundamental studies of coal structure and properties, the development and evaluation of new mining techniques, and work toward more effective processing and utilization of coal. The scope of these programs is indicated, in topical outline, by the table of contents. These investigations are integrated into a broad but coordinated effort to develop information on coal that will benefit the coal mining industry and the coal consumer while promoting the wise conservation and utilization of our national coal resources. Any attempt to summarize in one volume the progress in all of the program areas indicated must necessarily be limited to a brief review of developments, without detailed reporting of the data. However, while the brief discussion in each section will present only the highlights of the Bureau's work during the year, details of many of the operations or investigations described here can be found in the publications cited throughout the text. Other work, reported here for the first time, will be covered in greater detail in later publications.

Jan 1, 1962

A spectrochemical procedure applicable to the determination of iron, manganese, and magnesium in titanium metal and to the determination of alloying constituents in three types of titanium alloys is presented. Acid solutions of samples and standards are excited with a spark-type discharge and porous-cup electrode arrangement. The method is particularly applicable for analyzing samples for which a self-electrode method cannot be used. Calibrations are accomplished with synthetic standard solutions, resulting in a primary method that makes calibrations based upon results of other analytical methods unnecessary. Replicate determinations are reproduced to within 5 percent, and the average percentage deviations from reliable chemical values are less than 6 percent. The method can be extended readily to determine additional elements that are similarly soluble and have similar spectral sensitivities. It also can be used as a starting point to establish standards for a direct sparking procedure for analyzing titanium alloys. In view of the absence of established reliable analytical methods in the titanium industry, the spectrochemical method described here should prove to be a timely contribution.

Jan 1, 1956

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By Jr. Gabler

World resources of platinum-group metals appear ample for the foreseeable future; however, political and economic events in the last two decades have caused concern over the availability and reliability of an uninterrupted supply. Because of this concern, the U.S. Congress requested that the U.S. Bureau of Mines initiate a study of the flow of platinum-group metals in the economy that would delineate and quantify the production areas in which metal values are lost. As a result, the Bureau has developed a computerized commodity flow model for strategic and critical materials. Major attributes of this flow model are as follows: (1) it is generic and applicable to most commodities and (2) it can be updated as supply, demand, and/or production data change. The original model developed for cobalt, with slight modifications, was used to track the flow of platinum-group metals. This report follows the flow of platinum-group metals through their metallurgical, catalytic, and chemical applications and highlights areas in which significant losses occur because of downgrading, export, or disposal. The study indicates that materials containing about 63,426 kg of platinum-group metals were lost or could not be traced in 1989, representing about 63 pct of U.S. domestic consumption.

Jan 1, 1991

By Arthur L. Murray

"During recent months much criticism as to the efficiency of mine labor has been heard from various, sections of the country. No doubt much of this criticism has been well founded. The present lack of efficiency and of stability is due primarily to a spirit of restlessness and partial irresponsibility engendered during the transition from war conditions to peace time conditions. This spirit or unrest not only among the laboring classes but in every branch of the human family following a period of intense nervous tension in a nation appears to be a natural sequence of war and beyond the control of man. This condition will gradually disappear, and the majority of our people will again assume their natural order of living, but labor will for a considerable period be sensitive to these influences, whether they be exerted for good or for evil. Employers of labor should take cognizance of this fact and bend every effort towards the development of measures that promote efficiency and permanence of the working force.Labor efficiency depends upon many and varied factors. Some of these factors as applied to mine labor are briefly enumerated in the following paragraph:Selection and Placement of Manpower:In the selection of men the two main considerations are physical ability and adaptability. The laws of mechanics should be applied in the selection of men as in the selection of machinery. If a machine is required for a certain class of work, the type of machine known to be mechanically fit for such work is selected. Likewise, men should be selected with regard to their physical and temperamental fitness for the kind of work expected of them."

Apr 1, 1920

By T. F. Myners

This paper, describing the concentration methods and costs of Witherbee, Sherman and Company at Mineville, N. Y., is one of the series of papers on milling methods and costs being prepared by the United States Bureau of Mines. It deals principally with the production of high-grade concentrate. ACKNOWLEDGMENT The author is indebted to C. F. Jackson, principal mining engineer, United States Bureau of Mines, to A. M. Cummings, general superintendent of Witherbee, Sherman and Company, and to the company's engineering staff, for assistance in preparing this paper.

Jan 1, 1932

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979