Search Documents

By J Edmund Hay

Previous work by the Bureau of Mines to develop a test for determining the initiating strength of commercial detonators has been modified and extended. Recently reported results by the Bureau used a homogeneous liquid explosive to avoid the complicating effects of inhomogeneities; however, due to the belief that there may be essential differences between the initiation mechanisms of simple liquids and multi-phase mixtures and the fact that almost all commercial explosives are in the latter category, the experiments have been modified accordingly. The acceptor explosive is now a mixture of explosive-grade ammonium nitrate (AN) prills, methanol (MeOH) and nitromethane (NM). An additional change has been the use of the United Nations (UN) cap sensitivity test configuration in which the detonation witness is the degree of compression of a lead block, which is a quantitative measure of the response of the explosive. Results indicate that this mixture has sufficient range of sensitivities to be useful in comparing the strength of commercial electric detonators.

Jan 1, 1993

By Diane F. Baker, Cathy Aimone-Martin

A series of small-scale explosive experiments were conducted in a perlite mine near Socorro, New Mexico. These experiments were a joint effort between Los Alamos National Laboratory, New Mexico Institute Of Mining and Technology, Southern Methodist University, and Defense Nuclear Agency. The purpose of these tests was to measure the changes in the shock wave and seismic coupling as a function of depth of burial and structural setting. The size of the explosive charges ranged from 1 to 68 kg. Over 1150 measurements of velocity and acceleration were made on thirteen experiments using three component sensors. The sensors were placed to maximize the azimuthal coverage as well as to provide data at a variety of ranges from ~1 to 130 m A few far field measurements were made at ranges of ~2Êkm. While the bulk of the measurements were made on the surface, high g accelerometers were placed in one instrumentation borehole to provide some free-field measurements. Preliminary results indicate that significant differences in the amplitudes of signals can occur when the location of the explosive charges are changed by only meters. Part of the observed difference is attributed to variations in the rock immediately adjacent to the charge affecting the shock coupling; and part to the effects of the site characteristics.

Jan 1, 1994

By Thomas A. Gelormino, Ulrich La Fosse

"Deep blasting was used to densify foundation soils for a large manufacturing facility inChicopee,Massachusetts. A 360,000 square foot building, whose construction began inthe summer of 1990, is founded on alluvial deposits up to 90 feet in depth. These deposits are comprised of saturated very loose to loose fine to medium grained sands with traces of silt and gravel. During the building foundation design it was found that to withstand earthquake forces without soil liquefaction, it would be necessary to improve portions of the alluvial deposits by densification. The zone in need of densification extended from approximate depths of 20 to 50 feet. Several conventional densification methods, including vibrocompaction and deep dynamic compaction, were evaluated along with deep blasting. Detonation of 1-3/4 inch diameter charges of 65 percent gelatin dynamite (Atlas Power Primer) installed inside 2-inch diameter PVC casings to a depth of up to 40 feet, was used to achieve the desired densification. This method was selected over others due to its lower cost and decreased construction time. Although used in New England once in1940 for a dam and once in 1960 for a transmission line tower to improve foundation soils, there is no precedent found in the literature for densification by blasting to improve liquefiable soils below a proposed building. Details of a test program and the production blasting, including vibration data are presented. Pre-and post-blasting data conclusely shows an increase in the density of the sand deposit after blasting."

Jan 1, 1991

By Lewis L. Oriard

Ground vibrations associated with blasting are generally in a higher frequency range and of shorter duration than those generated by earthquakes, and the intensity scales for earthquakes cannot be applied directly to blasting vibrations without modification. Further, the profession does not need an intensity scale merely to estimate vibration intensity. If the blasting in question was not monitored instrumentally, it is a simple matter to estimate the range of intensities based on published prediction formulae or data from various sources such as Oriard (1), Nicholls et al (2), Hendron and Oriard (3), Siskind et al (4), and others. However, the profession has a serious need, for purposes of evaluating damage claims, to understand the relationships between vibration intensities and the levels of observed effects. The criteria for threshold damage do not apply to typical cases which usually involve structural damage. If the damage in question would have required ground vibration with a particle velocity of, say, 20-120 ips, damage is not verified by showing that the vibration merely approached a suggested limit to avoid threshold damage. That is not the question. This paper provides some guidelines for comparing severity of damage to intensity of vibration which would be required to cause such damage, much as is done when determining earthquake intensities. In addition, this paper includes a discussion of strain amplitudes induced by environmental forces, the predominant causes of damage to structures. Also, certain popular myths regarding blasting damage are discussed in the paper. Due to space limitations, the paper will not include a discussion of airblast effects.

Jan 1, 1989

By J. Schoonover, A. Moore

In the explosives industry, individuals face a multitude of hazards while working in mines, quarries, and construction sites. Safety becomes an ever-present driver as companies attempt to control costs, promote quality service and products, and grow business all while ensuring employees return home safely every day. One of the most challenging hazards that threatens the goal of absolute safety is flyrock. Ensuring that a blast does not result in rock leaving the blast area, thereby creating a danger for personnel in the vicinity, can be complicated due to the multitude of factors. Shot design, geology, operational procedures/techniques, explosive products, security plans, communication methods, and drilling practices can all adversely affect the safety of individuals helping execute a blast through an increased risk of flyrock. Flyrock can also pose a major threat to the public and other non-blasting personnel in proximity. Like many other industries encountering various challenging hazards, the explosives industry has recently adopted innovative technologies to help mitigate the risk of complex hazards such as flyrock. Specific applications of Unmanned Aerial Vehicles (UAVs), commonly referred to as drones, employed in the explosives industry can help reduce the likelihood and severity of a flyrock incident. This paper explores a case study and theories of how the integration of drone technology within blast security plans, mine planning, blast design, design auditing, and blast area clearance procedures can help to decrease the risk of a flyrock event through the provision of data and information previously unavailable. Multiple opportunities exist during a blasting operation to gather data using drone technology. It is these data-gathering opportunities that can be leveraged to be maximally equipped for the mitigation of flyrock. Better data from drones can be sourced and used in security plans and clearance measures as well as utilized during mine planning and blast design. Increases in the quality and quantity of information during these crucial steps of blasting has proven to be an effective way to increase the peace of mind for explosive end users. This peace of mind, along with design flexibility and adherence to performance, is why the integration and utilization of drone technology is key for effective flyrock risk reduction

Jan 1, 2024

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting, serving as a measure of blasting effectiveness. Fragmentation is sensitive to the inter-relationship among the design variables which define pattern geometry. Therefore, the objective of this study was to develop a model which represented a confined bench blast and to investigate the movement of burden-rock as the length to burden (L/B) ratio was varied.

Jan 1, 1985

By David Harrison, Brian Harrison

The Army Corps of Engineers completed the Charleroi Lock and Dam in 1932. It is located on the Monongahela river approximately 22 miles (35k) south of Pittsburgh in Charleroi, Pennsylvania. It is comprised of a 420-foot (128m) gated dam, and a 720-foot (219m) by 56-foot (17m) land side lock, which provides for a 16.6 foot (5m) vertical lift.

Jan 1, 2018

By William Clark, Rick Taylor

"Ajax Contracting was awarded the project to drill, blast and crush 100,000 tons of quarryrock for the Forest Service In Elk City, Idaho, during the summer of 1992. This projecttakes place in an area where environmental groups opposing any development in NorthernIdaho forced the Forest Service to look for road rock In any place they could get it. Theresult was that a quarry could not be developed. It was decided that rock would be takenfrom a road cut (under the guise of straightening the road) on the main artery of Elk City,Idaho making the drilling and blasting a very sensitive issue to the local truckers haulingtrees and lumber to and from a mill."

Jan 1, 1993

By James Camp

"During the 1950's a cement plant was rebuilt along a Missouri River bluff. The escarpmentwas composed of inter_bedded shale and limestone, typical to western Missouri. All of theraw materials needed to produce cement had been mined via room and pillar at the plantsite since the late 1800's. Portions of the mine began to fail in the late 60's., and by the mid70's M.S.H.A. declared all the areas where the lower Winterset limestone had beenremoved from the back to be ""unsafe"". M.S.H.A. explained that no work could beperformed in or above these unsafe areas unless the work itself was to render the area safe."

Jan 1, 1993

By Stephen Mansfield, Nathan West, El Khalil Seyed

In October 2017, a multi-bench failure occurred in the east wall of the Guelb Moghrein copper and gold mine in Mauritania. The failure extended 100 m (328 ft) vertically and horizontally and resulted in the sterilisation of ore, but no equipment or personnel were put in danger. The remediation plan successfully removed the failed material and the cutback resumed to a modified pit design, leaving ore reserves behind. In 2021 after completion of mining in another part of the pit, a plan was formulated to develop a narrow cutback behind the failed wall and recover the sterilised ore. Infill drilling defined a resource of approximately 2.9 Mtonne (3.2 Mton) of ore at 0.78% Cu and 0.67 g/t Au at a strip ratio of 5.5:1. The high strip ratio meant that it was necessary to mine thirteen benches of waste, or 156 m (512 ft) vertically, over a two-year period before reaching the first ore, with the cutback only being economically viable if all ore could be depleted at the end of the third year. The high economic risk of the project required a holistic approach to mitigate the risk of another wall failure, by addressing the following areas: 1. Pit Design: with help from an external Geotechnical Consultant, the pit design was optimised to include increased factors of safety, reduced stress points, lower overall slope angles and straight lined walls were replaced with curved walls. 2. Geotechnical Management: the site Geotechnical Superintendent worked closely with an external Geotechnical Consultant to better understand the structural geology. Slope monitoring was improved through an expanded network of prisms, regular in field inspections and the use of a slope monitoring radar. 3. Drill and Blast: new drill and blast designs were developed from first principles, consisting of production, wall control and presplit designs. Blast master polygons and bench development sequences were developed with consideration of the structural geology and the influence of the initiation designs. 4. Mine Operations: improving operational discipline was a critical factor that ensured the accurate execution of drill and blast designs and excavation to bench levels and pit limits. This holistic approach has enabled the safe development of the cutback down to the 936 RL (relative level), two benches below the point at which the previous wall failure occurred. Extraction of ore has occurred from the 960 RL, and due to faster than planned excavation rates, the cutback is expected to be completed ahead of schedule.

Jan 21, 2025

The use of angled shot holes can be extremely effective in blasting faces that either have a great deal of toe burden or where it is difficult to give a drill access to a face due to backbreak and face erosion. However many quarry operators are wary of using angled holes because of the perceived possibility of increased flyrock and uncertainty of the driller's abilities to drill at the designed angle.

Jan 1, 1994

By Tom Short

The contract to drive twin 4,100 foot (1250.5m) long tunnels under the existing Cumberland Gap highway was awarded to a Joint Venture of S.A. Healy of Chicago, Illinois and Lodigiani USA of Fairfax, Virginia in January of 1991 under a $51.8 million bid. Due to very complex geological conditions, there were six distinct categories of excavation, the New Austrian Method of ground support was utilized throughout.

Jan 1, 1993

By F Hunyadi

The seismic effects resulting from blasting are still a problem today although a great deal of research has been conducted in this field. A great amount of data defining the seismic effects can be collected with the proper instrumentation, however because of the difference in building materials, construction methods and foundations the characteristics of the seismic wave can not be directly correlated to the building response and possible damage.

Jan 1, 1975

By G Alan Foster

Because of the marked human response to blast effects and inherent defects present in many modern structures the real possibility of being named as a defendant in a law suit faces most blasters. Until recently even frivolous law suits involved a great deal of expense since legal costs were inevitably incurred whilst waiting for your day in court, which typically occurred some 2-4 years after the alleged damage took place.

Jan 1, 1989

By Lon Santis, David Leidel, John Tatom, Meredith Hardwick

This paper describes the development and methodology of the Institute of Makers of Explosives’ Safety Analysis for Risk (IMESAFR), a risk analysis software program for commercial explosives operations. IME is a nonprofit safety and security association devoted to the safe and secure manufacture, transportation, storage, and use or disposal of commercial explosives in the US and Canada since 1913. The software methodology’s basis is the U.S. Department of Defense Risk Based Explosives Safety Criteria Team’s Safety Assessment for Explosives Risk (SAFER) software. A diverse group of industry and government experts contributed to modifications to SAFER that reflect commercial operations. IMESAFR is intended to supplement the American Table of Distances (ATD) and offer standardized methods of managing risk from a wide variety of commercial explosives operations where the ATD does not apply. The modifications made to SAFER primarily involved the addition of commercial activities and potential explosives sites (PES). A review of commercial explosives accidents and operations over the last 20 years served as the basis for establishing probability of event values. An industry survey of commercial PES types in the U.S. and Canada was conducted to identify and address critical differences in commercial structures as compared to the military structures in SAFER. The paper concludes with discussion of the potential uses for quantitative risk analysis (QRA) and a description of other explosion effects software

Jan 1, 2007

By L D. Santis, L Wardrip

This paper begins with a summary of the development of the sheathed explosive charge from it's conception by the Bureau of Mines in 1981 through the evaluation of its safety, culminating in revisions to the Code of Federal Regulations (CFR), Title 30, Parts 15 and 75 which provide for its approval as a permissible explosive and safe use in underground coal mines. In 1989, Austin Powder Company decided to market a sheathed charge and proceeded to develop a commercial version which they call the Rock*Buster. The Rock*Buster was tested by the Bureau of Mines and subsequently approved as a permissible sheathed explosive unit by the Mine Safety and Health Administration (MSHA). Marketing of the Rock*Buster began in the Spring of 1990. In May 1990, the Rock*Buster was first used in an underground coal mine, Jim Walter Resources' (JWR) No. 4 Mine in Brookwood, AL. Trials with Austin's units were impressive. Representatives from MSHA, the State of Alabama, JWR, the United Mine Workers, and other local mining companies observed the charge break large boulders on the surface. Later, the charges were used underground to break large rocks from a roof fall that were obstructing ventilation. During its first week on the job, the Rock*Buster reduced the downtime experienced on JWR's longwall sections by quickly taking care of problem roof falls which halt operations.

Jan 1, 1991

By S. J. Dillingham

One of the primary goals of every blaster is to achieve the optimum blast design. Too much focus on efficient design, however, can cloud certain issues and exposures that must be addressed if the entire project is to be considered .successful.. Due to the known human response to blast effects and inherent dangers present in the use of explosives, the potential for the project being delayed or shutdown, or the blaster and associated company being named as a defendant in a lawsuit, is always a possibility. Therefore, the blast design and associated project bid must incorporate sound safety contingences and procedures that address those .what-if. Scenarios that may arise as a result of vibration, flyrock, public relations, and job-site personal safety.

Jan 1, 2002

By R Yang, P D. Katsabanis, W F. Bawden

Understanding the mechanisms which are taking place during the propagation of a stress wave generated by an explosive charge is of high importance in the detection, characterization and prediction of blast induced damage to the rock. Vibrations caused by the detonation of an explosive are suspected to contribute significantly to the extension of the damage zone. Vibration monitoring close to a blasthole is a relatively new field of research, the hindrance being the scarcity of transducers capable of sustaining extreme accelerations without damage. This paper focuses on the vibration monitoring aspect of a blast induced damage study; the experiment took place at Queen's test site and was meant to record near-field vibration as close as 1 m from 100 mm diameter blastholes.

Jan 1, 1993

By Pierre Mousset-Jones, Geraint W. Harris, Robert Karlin, Jaak Daemen

In order to minimize the ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will make it possible to more accurately locate the grade boundaries on the surface of a blasted rockpile prior to excavation. This paper describes the development and testing of a method to accurately measure the direction and magnitude of sub-surface blast movement. The technique involves the use of magnetic "radiometry, using a cesium vapor "radiometer and real-time differentially corrected, GPS system, to locate the post-blast position of magnetically enhanced target objects, whose pre-blast locations are known, without disturbance of the blasted rock. The objective is to design an accurate and efficient technique which can be integrated into a mines production cycle.

Jan 1, 1997

By Adrian J. Moore, Alan B. Richards, Rob Evans

Air and ground vibration from blasting is influenced by the delay pattern that is used. Wavefronts from blastholes fired in a blasting pattern can combine in certain circumstances to give increased blast vibration levels. A simple computer model has been developed which shows the combined effect of wavefronts from a multi-hole blast and identifies if wavefront reinforcement occurs, and permits delay patterns to be designed which will avoid or reduce wavefront reinforcement.

Jan 1, 1994