Search Documents

By C H. Ryu

This paper presents a simplified two-dimensional numerical model of block fragmentation in a Jointed rock mass during the late or throw stage of a blast after wave effects have subsided. The model is based on the distinct element method. Examples illustrate the approach and allow for a comparison of effects of Joint patterns on fragmentation and resulting block motion.

Jan 1, 1986

By Brian Stump, D. Craig Pearson

This work quantifies seismic coupling as a function of charge weight for single-fired (simultaneously detonated) explosions observed in the mine and at regional distances. These single-fired explosions are contrasted to standard production shots from the same mine. Production shots include cast blasts to remove overburden and coal shots for fragmentation. The blasts were conducted in a mine in NE Wyoming. The data sets consist of measurements in the mine (100-10,000 m) and at regional distance (360 km) using a seismic array near Pinedale, Wyoming (PDAR). The single-fired explosions ranged in designed size from 5,500 to 50,000 lbs. Peak amplitudes measured at a single element of the regional array are modeled by a power law relation dependent on explosive weight. Scaling constants were determined for each of the dominant regional phases: b(Pn) = 0.84±0.14; b(Pg) = 0.84±0.09; b(Lg) = 0.91±.08. Spectral ratios of observations from different explosions observed at the same station illustrate the frequency dependnce of the source scaling relations. Spectral ratios of in-mine observations are consistent with those of regional data. The observed single-fired ratios are well replicated by Mueller-Murphy source model ratios. The data and model illustrate both the increase in long-period spectral level and the accompanying decrease in source corner frequency with increasing charge weight. The coal and cast blasts that make up the production shots ranged in size from 77,000 to 4,738,230 lbs. The peak amplitude (1-20 Hz) for the largest delay-fired production shot (4,738,230 lbs.) is comparable to that of the largest single-fired explosion (50,000 lbs.). This comparison can be explained in terms of destructive interference between waveforms from individual boreholes introduced by delay firing. Shot specific models of delay firing suggest that peak amplitudes in this same frequency band for the production shots are insensitive to the total amount of explosives in the blast. Peak amplitude data at regional distances supports his modeling result.

Jan 1, 2002

There is an intuitive tendency to equate rock strength with rock stability, yet the two must be evaluated separately. A slope in strong hard rock is not necessarily stable, nor is a slope in weathered weak rock necessarily unstable. In some cases the reverse is true, depending on the geometry of joints and weak planes. The time element is a matter of special concern, that is how suddenly the failure begins and how rapidly it progresses. Sudden failures can be catastrophic, whereas creep usually is not. In soils and weathered rock, the process is usually incremental and is more likely to give some warning of impending failure. With careful observation, the failure process in these materials can be detected and monitored instrumentally or visually. In some cases, the slope may be stabilized, reinforced or modified. When that is not possible, there is usually enough time on this type of slope to remove men and equipment from the area before complete failure occurs.

Jan 1, 1996

By Deane Boddorff

A 440 Volt AC power line is a typical power source for energizing electric blasting cap circuits in driving hard rock tunnels. A common misconception exists that the caps actually see 440 Volts. This paper describes an analysis of the entire blasting circuit determining the current flowing and the voltage drops through each component. If, from such an analysis, one determines that the current to the caps is too low or too high, the components that require changing are easily recognized.

Jan 1, 1975

By T Davids, O J. Jordaan, M D. J Bonneau

As in most other parts of the world, the surface coal mining industry in South Africa is introducing emulsion explosives as the primary bulk blasting agent for use in wet borehole conditions where AN/FO cannot be used. Most of the emulsion products presently in use are gassed to provide sensitivity. The intimate mix between the fuel and oxidizer in the emulsion has been shown to produce a highly efficient explosive. However, a major difference between emulsion and the previous slurry products is its relatively low physical strength. This prompted Rand Mines' Duvha Opencast Mine, a major South African Escom power colliery, to conduct test work to illustrate the effect of emulsion physical consistency on blasthole loading. This paper presents the results of test work conducted at Duvha to investigate the problems associated with loading both AN/FO and emulsion in water filled holes, stemming emulsion holes, and in particular, to illustrate the difficulty in correctly introducing a stemming deck into the emulsion column. Time dependent behavior of the loaded emulsion holes is investigated. Velocity of detonation measurements for freshly manufactured emulsion, and for emulsion after loading through water with sleep times of up to 10 days, are presented.

Jan 1, 1987

By Eduardo Berger

This paper describes a mechanized loading system, the HYDRODOSE, which allows the use of pumpable emulsions in underground mining. It also describes a pumpable emulsion explosive for small diameter holes, HYDROMITE PDB. Included are test results carried out in two Chilean underground mines.

Jan 1, 1991

By J R. "Dick" Daniel

In the fall of 1988, The Cannon mine decided to investigate a central blasting system based on conventional electric blasting detonators being used to initiate rounds primed with Nonel detonators. The advantages of this hybrid detonator system were viewed as being safety and cost effectiveness. A study was done reviewing the safety aspects of utilizing a permanent blasting line installed throughout the main haulage drifts to a central blasting station located at the mine portal. The study addressed the following potential safety hazards: radio frequency induced current, stray current from both electrical utilities and transmission lines, galvanic and electrostatic sources of extraneous current.

Jan 1, 1989

By Paul Worsey, Gerald Rupert, Mark Kirkbride

The realignment of Highway H in the proximity of Crystal Cave (Springfield MO.) required the development of a blasting program that was both economical and efficient for construction, yet ecologically safe for the cave. Three component seismographs were strategically placed underground near prominent and sensitive cave features and the vibration levels from the construction blasting continuously monitored. Peak particle velocity (PPV) values were found to obey the square root scaling law and a peak particle velocity value of 0.3 in/sec was chosen as the safe maximum limit. This value proved adequate in preserving the integrity of the cave and its features. Scaled distances for the maximum and lower values enabled blasting personnel to select explosive charge weights per delay for given distance to the cave. Delays were determined from the dominant frequencies recorded underground.

Jan 1, 1997

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998

By R. K. Wharton

A European Directive requires that an explosive which is sold or transported within Europe must meet certain essential safety requirements from 1 January 2003. The assessment and certification of such an explosive is undertaken by an Explosives Notified Body and if the explosive meets the requirements a certificate is issued that allows the affixation of a CE mark. The presence of a CE mark ensures the product free access to European markets. The paper examines the requirements of the Directive, identifies those explosives that come within its scope, considers the role of an Explosives Notified Body, and explains the process of applying for certification.

Jan 1, 2002

By Paul Miller, Rene Laprade

Does a 76 mm Ø hole drilled over 45 m deep remain straight? This is the question asked by the Engineering department at Placer Dome's Dome Mine in Timmins, Ontario before they could lay out the initiation sequence in a long-hole production stope. Everyone realized that the holes would wander over such great depths, but it was important to know where they went.

Jan 1, 1998

By William E. Hill

The blasting program at the Valdez Creek Placer Mine must deal with challenging situations throughout the year. During the short summer, extreme water conditions must be confronted, while the winter months present problems of a different nature, where the overburden freezes to a depth of up to 18 feet. These obstacles require techniques borrowed from hardrock blasting combined with creative experimentation to overcome.

Jan 1, 1994

By Michael J. Sapko, Eric S. Weiss

The U.S. Bureau of Mines has been conducting research on the secondary explosion hazards associated with the mining of oil shale under gassy mine conditions. Explosive incendivity tests have been conducted in a 28 m~3 (1000 ft~3) gallery to evaluate the relative incendivity of experimental emulsion-ANFO blends. The incendivity was measured by determining the minimum inert stemming requirements for preventing the ignition of a methane-air atmosphere by the discharge of hot detonation products from a 5.7 cm (2.25 in) diameter borehole.

Jan 1, 1990

By Brad Johnson

Homestake Mining Corporations' open cut operation at Lead SD. experienced a highwall failure in October of 1993. The failure released a 75' section of rock wall at the 5280' level. It came to rest on the 5200' safety bench. Since work was in progress below the failure, this rock had to be removed for safety.

Jan 1, 1995

By J L. Jethwa, A G. Gaithankar

The paper deals with a software method developed to design the optimum blast parameters for tunnels and mine roadways for a given set of geo-mining condition without any major discontinuity. The application of the software is presently limited to 8 D-ahaped excavation where inclined hole cut or four-section parallel cut is used with smooth blasting technique.

Jan 1, 1993

By Wendell W. Harris, Stanley J. Vitton

In the United States each year it has been estimated that expansive soils cause approximately $9.0 billion in damage to buildings, roads, airports, and other facilities. This figure alone exceeds the damage estimate for earthquakes, floods, tornadoes, and hurricanes combined. Unfortunately, some cases of expansive soil damage (swelling) are blamed on rock blasting operations if the blasting operations are located within the immediate area. While simple tests, such as the Atterberg limits test, can characterize a soil as expansive, it does not necessarily answer the question whether the foundation soils are causing distresses to a structure. In particular, it appears that once a soil has been labeled as nonexpansive it is no longer considered as a problem soil, in which case blast vibrations become the prime suspect.

Jan 1, 1996

By Douglas Lindsey, Glenn Hazen, Shad Sargand

"With the innovation of computational equipment, an exact analysis of structures as dynamic systems is more approachable. Accordingly, the dynamic system can be established, if the natural characteristics such as the natural frequency and the damping fraction of a system are known. Through dynamic analysis, the response of a structure can be predicted from ground vibration, and it becomes possible to forecast the damage potential to the structure with reasonable accuracy. Most vibration will appear as single harmonic or superposition of waves that consists of several harmonics with different frequencies. A vibration signal can be expressed, therefore, as the function of sine waves. If a signal is periodic, the particular harmonic with the smallest frequency will befundamental and frequency of the others will be multiples of the fundamental frequency."

Jan 1, 1993

By Tom Burleson

High-speed photography has proven to be an extremely valuable tool for the evaluation of blasting practices in the Warrior Coal Basin. A research project, coordinated by Nelson Brothers Inc. and The University of Alabama's Mineral Engineering Department, has centered on the use of high-speed photography to study and analyze blast performance. A large number of production shots in this region has been filmed and studied. The data obtained from the films have been used to establish graphical relationships between certain blast parameters and overall shot performance. These relationships will be used to develop a computer model that will estimate cast results from a given burden explosive energy combination. This paper describes the methods and procedures used to develop these relationships. The results of the research are discussed along with plans for continuing the research project.

Jan 1, 1988

By Shawn Kirkpatrick, Yang Ruilin, Tamara Whitaker

In order to manage blast vibration in soft ground containing large diameter holes and large charge weights, a number of issues must be considered. This paper describes techniques to control and reduce near-field blast vibrations absorbed by highwalls in soft ground. Sympathetic detonations need to be controlled. Sympathetic detonations can cause excessive vibration due to an unknown number of charge weights firing out of sequence. The excessive vibration can cause damage to the ground. Sympathetic detonations can be controlled through proper design of blast patterns and, in some cases, through the use of specialized electronic detonators.

Jan 1, 2009

By Raymond V. Adolphson

The introduction of a new explosive component in 1955-56, called ANFO, featured much safer, effective blasting characteristics when compared to dynamite, accompanied by a notable reduction in cost. These savings mounted as borehole diameter or depth was increased with ANFO volume subsequently enlarged.

Jan 1, 1983