Search Documents

By N. Djordjevic

It is commonly accepted that the strength of rock measured from small samples tends to give unrealistically high estimates of the strength of larger samples, in situ blocks of rock or the rock mass in situ. The Weibull theory of the statistical strength of material provides a possible means for calculation of the strength of large rock volumes, based on the routine testing of small samples. Application of the Weibull approach to estimation of the strength of Moura coal showed an encouraging agreement with experimental results and the method was also applied to hard-rock andesitic and porphyry ore from Bajo de la Alumbrera, Argentina

Jun 21, 1905

By S A. M Crawshaw, J A. B Fortune

Trackless battery powered haulage vehicles have been in operation in British coal mines principally for longwall face transfer and personnel transportation. Changes within the industry have resulted in the introduction of room and pillar coal mining methods and the introduction of increasingly heavier longwall roof supports This has resulted in the introduction of: • Battery powered coal haulage machines, which, without the need for trailing cables, increase productivity within room and pillar mining. • Battery powered longwall shield haulers which are capable of carry ing the heaviest shield supports currently being utilised within the British coal mining industry. The conventional machines have been adapted from an American design to meet the requirem ents of European legalisation. This has seen the- emphasis being placed upon the supplier with the European M achinery Directive being introduced, necessitating the assigning of a 'C E ' m ark to each vehicle. Battery vehicle technology has advanced to meet the demands of the ever changing market and will no doubt he further adapted to meet the requirement of the British coal mining industry.

Jan 10, 1996

By D. C. Cooper, P. M. Green, J. A. Plant, P. R. Simpson, A. J. Reedman

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The Grampian Highlands and English Lake District evolved as part of the American and European continental plates, respectively, and were separated by the Iapetus Ocean until they were tectonically juxtaposed during the late stages of the Caledonian orogeny. The similarity in the controls of the distribution of gold pathfinder elements and gold mineralisation in the two regions thus provides important information for understanding the genesis of gold deposits in comparable tectonic settings elsewhere. The data presented are inconsistent with models that invoke a juvenile source of gold or its pathfinder elements. Instead, they support a model whereby gold and its pathfinders were initially concentrated in volcano-sedimentary sequences in rapidly subsiding, tectonically controlled basins and in associated volcanic rocks. Remobilisation and mineralisation occurred subsequently, probably as a result of an increase in oxygen fugacity associated with the influx of granite magmas into the crust and the establishment of hydrothermal convective circulation systems

Jul 1, 1991

By Mohammed Ali Shah, Martin Waller

The mining industry depends to a large extent on the availability of high performance equipment. For drilling this means a requirement for well engineered, reliable machines with mechanised handling and widespread utilisation of automatic control. Such machines enable performance optimisation of drilling operations and integration into a high productivity mining system. A review is presented of the current status of drilling technology as applied to the mining and minerals industry. This covers developments in: drill bit materials and design; drilling techniques; machine design; mechanisation; automation; and drilling control. It also covers the ways in which current and future mining methods and practices will influence the applications and demands placed on drilling activities. The probable impact of current research on the industry is discussed.

Jan 12, 1992

By J. A. Franklin, E. Broch, G. Walton

To make the best use of rock core, the mechanical character of the rock should be evaluated concurrently with conventional geological observations. The advent of simple techniques, such as the point load 'nutcracker' test, makes field logging of mechanical properties competitive with sampling and testing in the laboratory

Dec 1, 1971

By R. W. Ruddle

The advent of new methods of roasting, “flash roasting and fluidisation”, which are now under development, combined with the use of oxygen-enriched air, may markedly increase the SO2 content of roaster smokes. Skogmo suggests that the production of smokes containing as much as 50 per cent SO2 should be feasible. The use of flash smelting processes may well enable a similar increase in the SO2 content of smelter smokes to be made. In this event the recovery of sulphur would be greatly cheapened and the process might well be much more economic, even if allowance is made for the cost of generating the oxygen

Jan 1, 1953

By S. G. Tsimas, A. K. Moutsatsou, S. G. Tsivilis, G. K. Parissakis

(NH4)2SO4 can be used with success as a leachant to remove gypsum contained in celestite ores. The process, which is applied before flotation, provides an upgraded feed and problems related to the simultaneous flotation of CaCO3 and SrSO4 are reduced. The process is independent of the gypsum content of the feed so that each leaching stage decreases the gypsum content by almost 50%. The use of (NH4)2SO4 has an insignificant effect on the co-leaching of SrSO4 (0.45 wt.%) at each stage

Jun 13, 1905

By Winmill T. F.

Among the various theories proposed to account for the spontaneous ignjtion of coal, one which has at times been very strongly held is that the initial heating is due to the oxidation of iron pyrites. From the results described in this paper, it is possible to calculate roughly the rate of spontaneous heating of a specimen of finely-divided pyrites, on the assumption that all the heat developed is used in raising the temperature of the pyrites, and that none is lost. It is clear that where finely-divided pyrites occurs in considerable proportion among coal, it may be the chief factor in originating combustion, but that pyrites can only be the cause of a heating when it is present in considerable proportion, and in a very finely-divided state

Dec 1, 1916

1994 estimates for Porgera are probable and proven reserves of 58 200 000 t of ore grading 5 g/t Au. Gold mineralisation is related to an intrusive complex emplaced at shallow levels in poorly consolidated sedimentary rocks. The complex is located in a zone of fold-and-thrust deformation, whose formation may have been initiated shortly before emplacement and continues locally today. Abundant primary magnetite in the complex gives an intense, 5 km wide aeromagnetic anomaly. The deposit formed during two main stages of mineralisation, the first related to early magmatic-hydrothermal activity and the second representing later epithermal overprinting centred on the Roamane fault. Hydrothermal alteration followed closely on emplacement indicating a close genetic relationship between magmatism and mineralisation. Both stages of hydrothermal activity post-date and overprint early propylitic alteration. Several factors have acted in unison or sequentially to concentrate metals at the deposit, including an extensional or trans-tensional tectonic setting within an arc or collisional environment, the exsolution of a magmatic hydrothermal fluid prior to sulphur saturation in the melt, the development of the hydrothermal system into one favourable for transporting gold, the action of late-stage faulting in focusing epithermal fluid flow, and the role of dissolved gases in promoting fluid phase separation and high-grade ore deposition

Jun 19, 1905

By K. El-Barawi, Hussein M. Kamal

Chlorination was performed of iron-rich chromite ore from Barramyia, United Arab Republic (UAR), together with its concentrate. The effects of change of grain size, chlorine gas flow rate, time and temperature were studied. The extent and mechanism of chlorination were followed through chemical and structural analyses of the feeds and complete chemical analysis of the chlorination products. By conducting the chlorination process for short periods at 600°C or lower temperatures, products having high Cr-Fe ratios suitable for ferrochrome production can be obtained.

Dec 1, 1971

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991

Paper presented at the Mining Institute of Scotland's annual general meeting held in Glasgow, 8th April 1916. Although there is nothing novel or difficult about the sinking described, circular shafts are not numerous in Scotland so the details connected with such a sinking may be of interest. The shaft was sunk at Dykehead Colliery, Larkhall, which has been worked for over 50 years from the upper seams. It became necessary to sink another shaft to serve as a replacement downcast, by which the output might be maintained and some of the lower seams won. As the sandy clays regularly caused bulging into the rectangular shaft and sinking of the surrounding ground it was decided to make the new shaft circular and to enclose its mouth in a foundation-block of concrete resting on the solid clay. Details are given of the sinking, brick seating and lining, kettle strike, water-rings and doorhead lintels as well as the permanent fittings, winding gear and the cages themselves

Dec 1, 1916

By I. Garba

The Bin Yauri deposit in the Zuru schist belt of northwestern Nigeria is a vein-type quartz-sulphide-carbonate gold mineralisation hosted by a brittle fault zone. The occurrence of the mineralisation in a contact zone of a Pan-African granitoid was believed to be sufficient evidence of deposition from magmatic fluids. However, studies may now indicate a metamorphic source for the mineralising fluids. A study of rare earth element geochemsitry was used to investigate the nature of the fluid-rock processes involved and identify the sources of the auriferous mineralising fluids.

Jan 12, 1992

By A. B. Holland-Batt

Deposition velocities play an important role in many fields of engineering and an impressive range of measured data has accumulated in the literature. Numerous workers have addressed the problems that are associated with the prediction of deposition velocity because of its particular relevance to the design of pipelines and pumping stations. However, despite this extensive effort, the calculation of friction heads still requires reference to experimentally based graphs to determine Durand factors and there is still scope for improvement in the prediction of the deposition velocity at different solids concentrations. Equations to characterise the relationship between the Durand factor and the volume concentrations of solids in the slurry are presented. A correlation for the prediction of the deposition velocity is also developed and tested against some of the classical experimental data. The application of predicted values of deposition velocity in assessing the potential for the sanding-up of spiral separators is then described and a case study is presented.

Jan 12, 1992

By W. H. McAllister

The paper considers the geology and the coalfields that comprise the Scottish south area. It traces the history of known sources of spontaneous combustion and indicates the collieries concerned, with the position of the seams in the geological series where heatings have occurred. The methods of work over the years are described. It relates in detail the circumstances surrounding a fire at Bilston Glen Colliery in the Lothian Coalfield, and the heating at Killoch Colliery in the Ayrshire Coalfield, and the steps taken to deal with them. It also describes some of the difficulties in steep seam working. Methods adopted to prevent spontaneous combustion throughout the area are discussed, and some detail of the UNOR gas analyser is given. Finally, it comments on the present techniques in use in the area, particularly at Bilston Glen Colliery, to prevent spontaneous combustion.

May 23, 1905

The paper, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, presents experimental work undertaken to observe the quenching effect of different substances, to find the most efficient of these substances, and to arrive at a possible explanation of their preventive action. The coal-dusts experimented with were such as passed through a 100-mesh sieve (10,000 holes to the square inch), and were obtained by grinding the coals. The quenching substances, used in as fine a state of division as possible, included gypsum, dried Chance mud, quicklime, magnesia, magnesia alba (levis), anhydrous sodium carbonate, sodium bicarbonate, soda-crystals, Glauber salts, ground shale and boiler-ashes

Dec 1, 1916

By Z Hu

The technique of reclaiming disturbed land by use of a hydraulic dredge pump (HDP) (which is a set of hydraulic machines for earthwork), termed 'digging deep to fill shallow has been used in the reclamation of subsidence areas in Chinese coal mines. This paper discusses the operational principle of the technique and summarises its reclamation procedures, which are being used in current reclamation practice. The soil condition reclaimed by the HDP was studied. The results showed that the pioneer crops to be planted in the reclaimed soil should be the ‘pulse’ family crops, and that improvements to the reclaimed soil and the HDP technique itself are needed. Bused on the analysis of the previous technical processes, a new rational technical model for the HDP reclamation method is presented in this paper.

Jan 4, 1996

By R D. Lama, A Misra

One of the major factors restricting an increase in the productivity of a longwall mine is lower productivity obtained in a development panel. There has been a significant improvement in gate road development, particularly in mines requiring high density roof and rib bolting within 2 m of the face. Advance rates have increased from an average of 3 m to 5 m per shift in 1985 up to an average of 5 m to 10 m per shift in 1991. In mines at shallow depths with reasonably good conditions the increase has not been that significant. Advance rates have increased from an average of 7 m to 12 ni per shift in 1985 to an average of 12 m to 15 m per shift in 1991. Compared to the United States' (US) development rates, these are much lower. Extensive research work has been carried out to minimise cutting, wheeling, support setting time, and to optimise pillar length to achieve maximum advance rates. Pillar optimisation is very important in order to expedite adverse rates. This paper investigates various development rate technologies, both present and future, and optimises pillars to improve these dev elupment rates. Pillar optimisation is based upon time and motion studies conducted at mines in the Illawara region of New' South Wales, Australia, and the basic tools of arithmetic.

Jan 9, 1996

By Evans E. C.

Discussion of the paper presented at the Manchester Geological and Mining Society' general meeting held in Manchester, March 14th , 1916, with Leonard R. Fletcher, President, in the Chair included contributions by Fletcher L.R., Paton J.D., Orchard A.J.A., Ross A., Gerrard J. and Stephenson H., with the author's responses

Dec 1, 1916

By L Casari

A study of samples from three sectors of the mine, which was worked from Roman times to 1991, revealed different textures, mineral associations and distributions of trace elements in the sulphides. In the last decade before closure, grades of sphalerite concentrate were in the range 51.67-53.30% Zn and 2.21-2.86% Pb and of galena concentrate 69.43-71.62% Pb and 4.70-8.36% Zn, while the estimated by-product germanium content of sphalerite concentrates sold was 300-400 g/t. Passing the different run-of-mine materials through the same concentrator flowsheet produced middlings and tailings during the preconcentration processing. Separate and alternative treatment of run-of-mine products would have yielded improved recoveries of sphalerite and galena and better values of by-product germanium and cadmium

Jun 18, 1905