Search Documents

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

By L Besra, A. R. Prasad, B. P. Singh

The role of surface-chemical phenomena and the physical processes that participate in the dewatering of a suspension of alumina trihydrate were subjected to a systematic investigation, which has increased understanding of the influence of surface tension, contact angle and adsorption in the process. The residual moisture content of the cake can be reduced significantly through the use of surface-active agents in slurry pretreatment or as wash-water additives. The effectiveness of a particular surfactant is hard to predict from any single parameter, but is dependent on its ability to reduce surface tension and possibly to modify the solid-liquid contact angle. If scaled up to industrial operation of the dewatering step of the Bayer process in India, the use of these chemical additives could substantially improve its process economics, reducing the fuel costs for thermal drying by a much as Rs 50/t

Jun 21, 1905

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By Marshall Charles Riddell, John Carlon

local news

Jan 12, 1997

By R. Phillips

The low concentration of diamond in workable deposits requires very large samples for grade estimation, and results, even then, may be erratic and difficult to interpret. Although the Poisson probability distribution cannot accurately describe the occurrence of diamond, it is suggested that it gives a better estimate of grade than conventional methods, even from single samples. Examples illustrate the simple calculation required.

Dec 1, 1971

By R. K. Rath

Adsorption, electrokinetic and flotation studies were carried out. The maximum density of adsorption of guar gum was obtained at pH 7.5 on sphalerite and at pH 11.5 on galena. Flotation recovery of sphalerite was reduced only marginally by the presence of guar gum in the pH range investigated, whereas recovery of galena was reduced to about 20% at pH 12. Differential flotation tests on binary mixtures indicated that 10 ppm of guar gum can depress galena and separate it from sphalerite at around pH 12.1. Co-precipitation tests confirmed the formation of a metal ion-guar gum complex in the bulk solution, suggesting that this is the precursor to adsorption. The adsorption isotherms for both minerals followed Langmuirian behaviour, but adsorption of guar gum on galena was significantly higher than on sphalerite and dissolution tests indicated that the concentration of Pb ions released from galena was an order of magnitude greater than that of Zn ions dissolved from sphalerite

Jun 21, 1905

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By H. R. Thorpe

A floating gold dredge operating in coarse alluvial gravels of the Grey River on the west coast of the South Island, New Zealand, generated high concentrations of clay and colloidal particles in the dredge pond, which entered the groundwater system. Sampling was carried out at depths down to 20 m and it was found that variation of the length of the flow path occurred because of the movement of the dredge towards the piezometers. The alluvial gravels, the suspended sediments, the groundwater system and the water chemistry were all studied. Sediment concentrations were found to be highly variable with depth, but the relative concentrations in the depth profile were generally consistent as the flow distance shortened. The sediments were extremely fine and travelled further through the gravels than predicted. Comparison of field results with the available theory of deep filtration in clean beds of porous media gives some basis for estimating the behaviour of fine sediments in other alluvial systems

Jun 19, 1905

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By J. Konnerup-Madsen, T. Unlu, H. Stendal

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The region includes the Deveci siderite/goethite deposit and the Hasancelebi, Karakuz and Kuluncak magnetite/goethite deposits; Deveci is the only mine in operation. The area consists of a serpentine-gabbro complex overlain by a volcano-sedimentary sequence hosting the iron ores. At least three generations of hydrothermal alteration have affected all rock types except the latest trachytic dykes. The Deveci deposits occur in a pyroclastic volcano-sedimentary sequence with shales and carbonates equivalent to the main mafic sequence, whereas the other three deposits formed contemporaneously with the intrusion of trachytic dykes. The deposits are of the volcanic-exhalative type, with syngenetic siderite in pillow lavas or stratiform layers the primary and main Fe-bearing mineral. In the west hydrothermal alteration has replaced siderite in pillow lavas with magnetite or has remobilised sideritic iron into magnetite veins

Apr 1, 1995

By H. S. Sichel, W. J. Kleingeld, C. E. Dohm

A model of ore value distributions is presented that is the culmination of a statistical approach rather than simply a model that has been successfully applied to the evaluation of ore reserves. Detailed geological and physical observations based on large sampling data sets have been used to support the statistical modelling. Fundamental to the modelling process is the concept that the occurrence of a given grade value in space is a function not only of the presence of the mineral but also of the fact that it is associated with a specific trapping mechanism. The concepts have been specifically applied to gold mineralisation

Aug 1, 1995

By R. L. F. Kay, T. A. Fletcher, A. J. Boyce, C. M. Rice

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The synorogenic, mafic Ordovician intrusion comprises orthopyroxene-rich xenoliths and mafic-ultramafic cumulates with low-grade pyrrhotite, chalcopyrite and pentlandite mineralisation. Despite abundant textural, mineralogical and O isotope evidence for significant assimilation of country rocks, S isotopes indicate only a modest uptake and suggest that mineralisation is dominated by magmatic sulphur. The preferred explanantion is that the magma was close to S saturation on emplacement. Uptake of elements such as Si and O led to early crystallisation of orthopyroxene, resorption of olivine and early segregation of a sulphide liquid. Post-magmatic interaction with a high-temperature, surface-derived fluid, whose movement may have been controlled by regional shear zones, reset biotite and whole-rock O isotope values but not those of orthopyroxene. This model identifies the presence of olivine-rich rocks and evidence of extensive assimilation as guides to prospectivity

Jun 19, 1905

By D. F. Ball, P. R. Dawson, J. T. Fitton

Report of discussion at December, 1970, IMM general meeting (Chairman: M. J. Cahalan, President) and contributed remarks on the paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C189-96, plus the authors' replies. Contributors included Cohen E., Hope B., Wasse D.G., Shakespeare A.G., Burwood D.S., Jones H.A., Dartnell J., Carter G.C., Henderson T.A., Relf G. and Clark S.W.

Dec 1, 1971

By G Williams

Discussing equipment, systems of work, the need for updated programmes of local seismic exploration, and developments within the South Wales coalfield.

Jan 1, 1993

By L. J. Cabri, J. M. D. Wilson, R Lastra

An image analysis program can search for gold minerals in polished sections by scanning about 100 x 100 back-scattered electron images at a magnification of x400, allowing gold grains as small as 1 micrometre in diameter to be detected. Typically, a c.15 h overnight search of a product smaller than 45 micrometres will scan c.1 500 000 particles, providing data that are not easily obtained through manual operation of an optical microscope. The program locates grains of the correct brightness, acquires gold X-rays from them by wavelength-dispersive spectrometry, filters the data to remove artefacts and record the images and stage locations for subsequent retrieval. At the end of the run, the program allows the operator to verify and identify the grains found. Industrial studies at Canmet have included determining the nature of gold in cyanidation tailings, checking the mineralogy and size of gold grains in samples from an Indonesian Cu-Au concentrator and locating and measuring gold liberation and grain sizes in an ore

Jun 21, 1905

By B. Gazea, A. Kontopoulos, A. Kourtis, K. Adam

Static tests give a measure of the balance between acid-producing and acid-neutralising mineral components in a material, while kinetic tests determine acid generation and neutralisation over a long period. Drill-core samples from the amphibolite and gneiss host rocks of the Stratoni lead-zinc sulphide deposit in Greece and mine/mill waste samples from Stratoni and Olympias were examined by the standard acid base accounting, BCR and net acid production tests. Mineralogical data on the materials and resulting residues were used to illustrate the differences between the methods and establish their ranges of applicability. BCR seems to simulate most closely the conditions prevailing during generation of acid mine drainage but is time-consuming and requires elaborate equipment. Acid base accounting is suggested for standard screening; net acid production might be used in the field or for solids with less than 10% S

Jun 19, 1905

The first part describes a model (the C model) based on the motion of the grinding charge. The charge is treated as a continuum, which allows analytical solutions to the equations that are developed. The C model is equally applicable to ball-, semi-autogenous and autogenous mills and contains a description of the power draw of both the cylindrical section and the cone-ends. Differences between the power draw of grate- and overflow-discharge mills are described from consideration of the different shapes and compositions of their charges. A large database of industrial mill data is used to demonstrate the accuracy of the model. Part 2 describes a simpler, empirical model (the E model) whose performance is based on that of the C model. The same database was used to assess the predictive capabilities of the E model. The model was shown to be only slightly less accurate than the C model despite its much simpler structure

Jun 18, 1905

By D. G. Skinner, M. SC. Griffiths

"The natural difficulties associated with the size evaluation of dusts render absolute measurement difficult, or indeed, impossible. Assuming that the desirability of gravi­ metric sampling be conceded, it appears likely tha,t the most suitable means available for physical evaluation are the method of total turbidity measurement, to give a con­ ventional value for specific surface, together with microscopical examination, the great merit of the latter being that in the hands of an experienced operator, semi-quantitative discrimination between coal and other particles is possible.The pipette method, as modified by Fryer, probably-deserves more attention than it has received up to the present. Whatever method is used, it is recommended that in view of the lack of medical knowledge, as much information as possible should be obtained with reference to the total mass concentration, the surface area of the total dust,' and the mass and area of the particles below 5μ in size."

Jan 1, 1947

By I. D. Nock, R. M. Parkin

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Knowledge-based condition monitoring of cone crushers). A large proportion of the electricity used by the quarrying industry is consumed in the comminution and sizing process. In most cases aggregate processing plants operate with minimum control features resulting in limited operational efficiency. Improved control is required to increase operational efficiency with concomitant savings associated with reduction in re-circulating load and improved resource utilisation. Development work has suggested that a combination of adaptive control and process condition monitoring could improve control of comminution plants. Many commercial process control and condition monitoring systems are available, but none were deemed suitable due to the domain specific characteristics of the application. An assessment of the particular characteristics of cone crushing concluded that the application was best suited to the use of small domain specific process control combined with bespoke condition monitoring. The processing power of the control system for the project is a function not of the academic requirement, but rather the economic and practical constraints imposed by the application. As a result of the constraints a high-end PC system has been designed in preference to a workstation. Within the research project work packages are sub-divided into novel wear sensor development, knowledge based control/condition monitoring and the investigation and mathematical modelling of the wear mechanisms inherent in cone crushing. Numerous strategies were considered to implement the control system outlined. The system currently under development is a modular design which utilises intelligent novel sensors to provide a variety of data inputs

Apr 1, 1994

By D. V. Venugopal, W. W. Gardiner

Spessartine-quartz rocks are manganiferous sedimentary rocks rich in spessartine and quartz which occur in north-central New Brunswick. They represent a recrystallised manganiferous siltstone/chert that is contained in or associated with red manganiferous siltstone (RMS) units. The spessartine-quartz rocks and RMS form part of an Ordovician volcanic and sedimentary succession within the Appalachian-Caledonian orogen which hosts numerous massive sulphides and polymetallic vein deposits. The New Brunswick spessartine-quartz rocks are spatially and temporally associated with stratiform base-metal, precious metal and hydrothermal tin-tungsten deposits. This suggests that spessartine-bearing lithologies and zones can be useful in predictive metallogeny and for the understanding of the stratigraphy and palaeographic setting of the early Palaeozoic rocks of the Appalachian-Caledonian orogen.

Jan 12, 1992