Search Documents

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

By A. Shandilya

ACC ECOSAND is finely powdered crystalline silica, which can replace natural sand usage in concrete and plasters. ACC ECOSAND ensures a comparatively denser concrete than those made only with natural sand and / or quarry fines / Manufactured Sand (Artificial Sand). Moreover, there is a significant gain in compressive strength (10-15 %) & durability in concretes (Reduced chloride conductivity leads to increased durability). ECOSAND is a by-product of froth flotation of limestone. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full-fledged mineral beneficiation process is adopted to enhance the usage of flotation reject in concrete and plasters. Optimum level for usage of ECO-SAND is 50%. With 50% usage of natural sand+50% ECO-SAND in concrete mix, 1 day, 3 day, 7 day & 28 day compressive strength is increased by 30.1 %, 22.6 %, 15.1 % & 11.0 % respectively and with moderate chloride permeability as compare to 100% Natural Sand. Keywords: froth flotation process, beneficiation studies, Denver cell, ECOSAND, siliceous material, durability & compressive strength, RCPT

Sep 1, 2012

By A. K. Mukherjee

In this apparatus closed sized particles are placed in a container and then fluidized by passing water through the load of particles. Water flow is adjusted to deposit particles in one or more layers depending on the specific gravity of each of the particles, after which the deposited particles are separated in portions of different specific gravity. The obtained portions represent different ore content of the closed sized fraction. The process is repeated for all other size fractions to generate washability curve of the feed. Three different types of iron ores and one coal sample are tested in this equipment. The theoretical yield-grade curve generated for iron ore feed is unique in absence of any such practice for ore minerals. Similar curve is generated for coal and it is compared with washability curve, an existing practice followed worldwide. This comparison validates the performance of the process and the equipment.

Sep 1, 2012

By P. Romm

The German Kupferschiefer (copper shale) mining history reaches back over 800 years with its last active mines being shut down in 1990. Increasing metal demands and potential thread of future supply shortages led to the initiation of new exploration programs including feasibility studies for the Spremberg deposit as well as Federal Ministry of Education and Research (BMBF) funded research investigations of Kupferschiefer Waste Dump treatment in the Mansfelder region. This article describes the sensor based sorting results of coarse Kupferschiefer via Near Infrared (NIR) Sorting, being conducted by the department of mineral processing (AMR) in Aachen, Germany. It provides information about the necessity of presorting of the different ore types prior to flotation and puts the NIR Sorting results into context with conventional Kupferschiefer processing. Keywords: NIR sorting, kupferschiefer, sensor based sorting, preconcentration

Sep 1, 2012

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By Mario Gerards

Maturing populations create an increase in the demand for the type of non-ferrous metals, which are used in the manufacturing of electronic products. The depletion of existing high-grade deposits, make it necessary to boost the efficiency of beneficiation processes and most importantly the yield (recovery rate of the value commodities). Increasing demand now makes it worthwhile to tap into resources, which were previously considered waste, for example secondary deposits such as tailing ponds and electronic waste. In order to achieve increased yields, increasingly finer, or even ultra-fine fractions have to be treated. In most cases, mineral characteristics such as size and density call for non-mechanical, high-capacity technologies to be used. There are various technologies that allow for the separation of fines and ultra-fines. This paper outlines the dynamics and efficiency of pneumatic flotation with emphasis on its application to the recovery of non-ferrous metals, from electronic waste. The conventional agitator flotation technology of an electronic waste processing plant was not able to recover ultra-fine non-ferrous metals satisfactorily, due to losses within the tailings. Because of its adaptability and its inherent suitability for non-ferrous metals, pneumatic flotation has been incorporated to the existing process achieving excellent results. The merit of the process lies in the state of the art technology, which does not utilize compressed air and any rotating parts, which results in a reduction in wear and energy requirement, both features of this innovative technology. In addition, the use of pneumatic flotation resulted in a significant reduction in residence time, when compared to mechanical flotation. Pneumatic technology is able to influence air bubble size in a flotation cell, by changing the speed and pressure of the slurry stream. Higher slurry velocities lead to the formation of smaller air bubbles, which is required for the successful flotation of ultra-fine particles. Conversely, decreasing the slurry velocity leads to bigger air bubbles. The optimum bubble size can be created according to different feed characteristics. This is important in case of feed fluctuations.

Sep 1, 2012

By B. McFadzean

Thiol collector mixtures are commonly used in the flotation of base metal sulfides and platinum-bearing ores. There are synergistic benefits claimed for these collector mixtures, with mixtures lowering total dosage requirements, improving coarse particle recovery and the rate of flotation. Some of the secondary collectors are known to have frothing effects. Therefore, a previous study aimed to decouple froth and pulp effects and considered only the bubble-particle attachments in the pulp. This was achieved through microflotation experiments, where various ratios of the ethyl and isobutyl chain lengths of xanthates, dithiocarbamates and dithiophosphates were used as collectors. Results from these experiments showed a marked increase in galena recovery using mixtures of xanthate with either dithiophosphate or dithiocarbamate. In the current study, the froth phase was introduced in the form of batch flotation studies to determine whether benefits noted during microflotation experiments would be carried through to a more realistic froth flotation scenario. The findings show that there was no significant difference in the flotation recovery between the best single collectors and mixtures of these collectors. In addition, single collectors that behaved poorly in microflotation experiments showed good flotation performance in the batch flotation experiments. The differences between the microflotation results and the batch flotation results are attributed to differences in particle froth stabilizing properties and/or differences in energy input between the microflotation and batch flotation cells. In addition, galena and pyrite showed marked differences in frothing effects and in their preferences for collector type. Keywords: froth flotation, collector mixtures, sulphide minerals

Sep 1, 2012

By Ashiwani Kr Gupta

The floatability of coal is affected by the presence of dissolved inorganic ions in plant process water. Water quality is characterized in terms of conductivity, hardness, turbidity and composition of oil. These quality indices are correlated with coal flotation performance for three different water named, ?R&D laboratory tap water?, ?process untreated water? from West Bokaro wahsey-2 Tata Steel, India and ?process treated water? after passing laboratory developed treatment process. The study clearly indicated that a significant quantity of clean coal is being lost due to poor process water quality used in the flotation process. The laboratory investigations showed that if these dissolved salts and suspended solids are reduced to even 50%, a clean coal yield improvement by minimum 5%~10% at the same ash level could be expected. Therefore, the conventional practice of water recycling though a thickener or a tailings pond needs a complete re-look. The water treatment process for recycled water has also been discussed for improving the process water quality as well as enhancement in flotation performance efficiency.

Jan 1, 2014

By Andrzej Luszczkiewicz, Aleksandra Potulska

"Flotation is a basic process of beneficiation of mineral raw materials which requires very fine grinding for liberation of valuable minerals. Probably flotation will also play this role in the future. In the case of flotation of difficult-to-upgrade non-ferrous ores, currently one of the most important trends in technology development is solution to fine grinding even down to a few micrometers in size and elaboration of effective flotation technology for such fine particles. Both industrial flotation data and many investigators suggest that the best results of flotation of ore minerals are observed for particle size range from 20 to 100 µm. Many base metal ores require grinding below 20, or even 10 µm, to liberate valuable ore components. However, industrial flotation of particles below 20 µm in size creates numerous challenges. Further complications may be caused by a complex nature of the ore, especially when the valuable metals are present in several different sulfide minerals. This problem occurs in the case of the Polish sedimentary copper ores. In the present study, flotation of the ore of different size distributions and degrees of grinding, having the size of particles below 25 µm, was investigated. The behavior of different sulfide minerals naturally present in the ore was analyzed. The best results of flotation tests were obtained for the ore ground down to 95% below 25 µm. Narrow size fractions -10; 10-15; 15-25; 25-40, and +40 µm were separated using special micro-sieves and mineralogical as well as chemical analyses of each size fraction were carried out for monitoring the behavior of the fine sulfide particles. Differences between flotation of chalcocite-digenite, bornite, chalcopyrite, covellite, galena and pyrite-marcasite naturally occurring in the ore were described. The role of different particle sizes in flotation performance of each mineral was also presented."

Jan 1, 2014

By S. H. Morar

Froth stability is widely recognized as a key driver of flotation selectivity. It is well known that froth stability is affected by the type and quantity of surface active reagents present (frothers), and the concentration and hydrophobicity of solid particles present. While some studies have been performed on the effect of frothers on froth stability in three-phase systems and the hydrophobicity of particles present, very little work has been performed on the effect of solids loading on froth stability. This may be due to insufficiently robust measurement techniques. This paper investigates the use of a new machine vision measurement to measure solids loading, and the relationship between this measurement, bubble size, and bubble burst rate on the froth surface. Keywords: froth flotation, machine vision, solids loading

Sep 1, 2012

By Steven Bradshaw, Edson Charikinya

The application of high power microwave energy to secondary crusher products has been shown to induce micro fractures and cracks in the ore. This suggests that heap leaching could benefit from microwave-induced fractures, as the extent and kinetics of heap leaching processes depend on the accessibility of grains to lixiviants, which can potentially be improved through microwave treatment. The density and pattern of microwave induced cracks and how these cracks subsequently affect heap leaching recovery has not yet been investigated. The objective of this study was to apply X-ray micro computed tomography (X-ray CT) to investigate microwave induced cracks in large cone and HPGR crushed sphalerite particles within 3D space. The ore particles were microwave treated in a single mode microwave applicator coupled to a switched mode power supply and a water cooled microwave transmission sub system operating at 2.45 GHz. The ore particles were treated at specific absorbed microwave heating energies of between 2 and 3kWh/t by treating at 6 kW of forward power for treatment times of 1 s. X-ray tomography analysis was conducted on fine (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm sphalerite particles before and after microwave treatment at voxel resolutions of 5 µm, 15 µm and 25 µm respectively. Image segmentation, thresholding and spatial registration techniques were used to study crack patterns in 3D images of HPGR and cone crushed particles. Analysis of the X-ray CT images after microwave treatment shows considerable micro crack formation within the Cone and HPGR crushed particles. The cracks pattern showed interphase cracks propagating across all phases, with no evidence of preferential cracking. A greater density of microwave induced cracks was observed on fine (-5+4.75) mm particles compared to the medium (-16+9.5) mm and (-25+19) mm large particles. The results showed overall increased particle porosity following microwave treatment.

Jan 1, 2014

By N. Nikolaeva, A. Romashev, T. Aleksandrova

Energetic characteristics identify energy consumption for destruction of prills and kinetic characteristics rate formation of finished size grade in the course of destruction and identify crushing and grinding equipment capacity. And if screen sizing or classification processes are applied in the cycle of ore preparation, then the use of characteristics of separation to size – separating characteristics – is required for theoretical description. Separating characteristics have a lower profile for ore preparation but, nevertheless, they have to be taken into account especially for balance and design calculations of crushing and grinding circuits. In most cases there are impregnations of minerals which vary widely in energy consumption and destruction kinetics and thus polyminerality must be considered as one of priority factor. Raw materials which passed through crushing and grinding processes can be assessed numerically by functions of fractional composition of two types: differential distribution function y ( €) and assay function B( c ) . A set of experiments on grinding of crushed raw materials at different time (up to various sizes) was conducted to analyze effect of grinding size of carbonaceous overburden on function y € and B ( c) as well as to justify the possibility of preconcentration of raw materials at the stage of ore preparation. Analysis of metals distribution per size grades showed that metals are concentrated in size grades of less than 0.315 mm (which is equivalent of cut point for this type of raw material), however, there is no overgrinding and oversludging of material, and enriched product for its further processing can be excluded with the help of classification. The stage of size segregation was tested as a method of preconcentration of raw materials for optimization of ore preparation and further separation.

Jan 1, 2018

By Nina Panteleeva, Elena Afonina, Stanislav Titkov, Jury Buksha

"Flotation processing of water-soluble minerals (potassium ores, sedimentary salts of salt lakes) is currently the main method for production of potassium fertilizers and concentrated carnallite which is the initial product for production of metallic magnesium. Flotation of sylvite (KCl) and halite (NaCl) is carried out in the electrolyte solutions: KCl-NaCl-H2O and KCl-NaCl-MgCl2-H2O. The report presents the results of studies of the effect of concentration and the electrolyte type on the size of air bubbles in a flotation cell in comparison with the floatability of mineral constituents of potash ores. The floatability in electrolytes of various compositions has been studied: - of sylvite (KCl) by alkylamines, - of halite (NaCl) by alkylmorpholines, - of silicate-carbonate slimes contained in the ore by ethoxylated surfactants. The reagent modes (regimes) activating the flotation desliming of potash ores have been developed."

Jan 1, 2014

By S. V. Petrov

In recent years, heap leaching of gold is becoming wide spread due to low capital and operational costs that allows economically feasible processing of low-grade and cut-off grade ores. Currently, over 30 heap leach projects are operated in Russia. Some of the deposits treated by heap leach methods are almost depleted. Therefore, they will soon require spent heaps detoxification and reclamation. Traditionally, spent heaps are detoxified by chemical treatment. This process is characterized by relatively high kinetics and requires expensive reagents and additional equipment. The main disadvantage of this process is secondary contamination of the solutions by products of detoxification reactions and impurities contained in reagents. If there is enough time, spent heaps can be detoxified by natural degradation. The advantages of the proposed method are low operational costs due to use of existing heap leaching facilities and eliminating the need for chemicals for spent heaps detoxification. Residual concentrations of cyanides and thyocyanates in liquid phase (wet ore) of spent gold ore heaps after detoxification were 0.2~0.3 mg/L. Heavy metals were almost completely removed. The method was successfully used for detoxification of spent heaps at two gold mines.

Jan 1, 2014

By B. Vasanthakumar

In this study, the effect of adaptation of B.subtilis to sphalerite and galena with respect to the selective flotation of sphalerite from the sphalerite-galena synthetic mixture has been examined. The changes in the surface charge of the mineral and the bacterium, cell wall components and the profiles of secreted proteins are discussed. The flotation recovery of galena increases with the increase in the adaptation cycle of B.subtilis to sphalerite and galena, while the flotation recovery of sphalerite is independent of the adaptation cycle with either mineral. From the gel electrophoresis analysis, the protein profile for the unadapted and adapted cells is found to differ distinctly and this may be attributed to varying molecular weight fractions arising from different growth conditions. Electrokinetic measurements showed shifts in the iso-electric points of not only B.subtilis but also of the chosen minerals after adaptation. Additionally, the zeta potential of B.subtilis is found to become less negative after bacterial adaptation to the chosen sulfide minerals, while it showed an increase in the magnitude of surface negative charge after various enzymatic treatments. The change in the surface morphology and cell wall components such as phosphate, uronic acid and acetylated sugars of the bacterial species during adaptation to sphalerite and galena has been assessed. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite can be preferentially floated from galena in the presence of the insoluble fraction of lysed B.subtilis cells initially adapted to sphalerite, with a high selectivity index. Keywords: bioflotation, b.subtilis, mineral adaptation, sphalerite, galena

Sep 1, 2012

By C. Y. Wang

Anodic reaction mechanism of complicated antimony-lead concentrate in Slurry Electrolysis has been investigated by the anodic polarization curves determined under various conditions. The main reactions on the anode are the oxidation of FeCln (2-n), though the oxidation of jamesonite particle on the anode can occur during the whole process, it is less. With the help of mineralogy study and relevant tests, the leaching reaction mechanism of jamesonite and gudmundite during Slurry Electroly-sis has been ascertained also. Because of the oxidation reaction of FeCl3 produced by antimony-lead concentrate itself, the non-oxidation complex acid dissolution of jamesonite, the oxidation complex acid dissolution of gudmundite, and the oxidation of air carried by stirring, the leaching ratio of antimony reaches to about 35% when using HCl-NH4Cl solution to leach antimony-lead concentrate directly. So given the theoretical electric quantity, which to oxide antimony in Slurry Electrolysis, all of antimony, lead and iron, which contained in antimony-lead concentrate, are leached.

Jan 1, 2014

By S. J. Liu

The conventional collector for bauxite mineral is oleic acid, which is highly insoluble and must be used in high dosage in bauxite flotation operations, that is the great drawback of oleic acid in use. A series of hydroxamic acid were synthesized, and their collecting ability to certain minerals in bauxite: diaspore, kaolinite were studied. The collecting power of various reagents to diaspore in an incremental sequence were shown as follows: benzyl hydroxamic acid<amylic hydroxamic ac-id<heptylic hydroxamic acid<oleic acid<octylic hydroxamic acid; while the incremental sequence of the collecting power to kaolinite was like this: benzyl hydroxamic acid<amylic hydroxamic ac-id<heptylic hydroxamic acid<octylic hydroxamic acid<oleic acid. It could be seen that octylic hydroxamic acid had the capability of high collectivity and good selectivity, and octylic hydroxamic acid was chosen to use in the following experiments. Reduced zeta potential showed the adsorption of the anionic collector on the mineral. By the adsorptive capability and IR tests, the adsorption of octylic hydroxamic acid on diaspore was determined to be chemical absorption, which was greater than that of oleic acid, as it was physical absorption. Results of floatation experiments on manually mixed minerals indicated that the collectivity and selectivity of octylic hydroxamic acid were better than oleic acid.

Jan 1, 2014

By Gorki Davila, Irineu Brum

"Brazil has large reserves of coal (32 billion tons) located predominantly in the south of the country. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently the country&apos;s strategic planning aims to minimize the gap between coal and resources traditionally used in the Brazilian energy matrix. In this scenario the processing of Brazilian coal by flotation appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of flotation for a specific Brazilian coal. The material used in this study consists of fine coal that is usually discarded as waste and deposited in the tailings dam. The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The variables analyzed were the influence of size particle, solids concentration in the pulp, the concentration of surfactants and frothers to be used. The results showed that it is possible, from a feed with around 65% of ashes, to obtain products with approximately 35% ashes with mass recoveries about 40%. The types of collector reagent and foaming employees result in different concentrates. This study also presents a preliminary analysis of the effect of water recovery in concentration parameters."

Jan 1, 2014

By Tong Guan, Guangqin Fu, Lihong Deng, Xiaotong Zhou

The raw ore contains many kinds of valuable metal elements. It is rich in valuable metal elements, such as Pb, Zn, Sb, Sn, Ag and is associated with S,Fe,As,In,Cd. A new technology which includes medium intensity magnetic separation, preferential lead flotation, zinc-sulfur bulk flotation, zinc-sulfur flotation separation, tin gravity separation and tin slime flotation was chosen to recover valuable minerals in the raw ore, and the iron concentrate, the lead concentrate, the zinc concentrate, the sulfur concentrate and the tin concentrate can be obtained. To the zinc-sulfur bulk concentrate with the grade of 7.21%Zn and 16.97%As acquired by the zinc-sulfur bulk flotation, two different flowsheets of Zn-S separation technology are chosen to study. The lab test shows that when using lime+DM as depressor, the zinc concentrate assaying 47.73%Zn with the recovery of 95.01% can be obtained and the test indexes are better than that of the flowsheet which using lime as depressor. At the same time, the Cd content is 0.65% and the In content is 0.10% in the zinc concentrate, so they all reach the smelting comprehensive recovery standards and the As content decreases to 0.23%. Finally the flotation separation of christophite and As-bearing sulfide minerals can be successfully realized.

Jan 1, 2014