Search Documents

By Leopoldo Gutierrez, Esau Arinaitwe, Marek Pawlik

"The effect of various polymers, including: anionic carboxymethyl cellulose (CMC), polystyrene sulfonate (PSS), humic acids (HA) and non-ionic hydroxypropyl cellulose, on the wettability of Athabasca bitumen was evaluated through dynamic contact angle measurements using the captive bubble technique. The tests were carried out as a function of pH at a constant ionic strength (0.01 mol/L sodium chloride). The evolution of the three-phase contact angle between the solution, bitumen and an air bubble was followed as a function of time over a period of ~6 minutes. The contact angle data were modelled using a first-order kinetic equation. The results were analyzed in terms of the initial contact angle, the evolution rate constant, and the steady-state contact angle value. In the case of anionic polymers, a pronounced decrease in the initial contact angle value was observed at pH 3. Under acidic conditions, there was no significant effect of CMC observed on the steady-state contact angle value but PSS and HA significantly decreased the steady-state contact angle value. At pH 8.5. the anionic polymers did not affect the wettability of the bitumen surface but they significantly decreased the contact angle evolution rate. These results suggested that CMC is not capable of permanently lowering the hydrophobicity of bitumen, and the polymer only slowed down the evolution of the contact angle to the steady-state value. The results also showed that polystyrene sulfonate and humic acids were capable of making bitumen hydrophilic but only under acidic conditions. Only hydroxypropyl cellulose (HPC) produced a large decrease in the steady-state contact angle under alkaline conditions (pH 8.5). The kinetics of contact angle evolution in the presence of HPC was also drastically lowered. The results were discussed in terms of the chemical composition of the polymers and their different affinities towards the bitumen surface."

Jan 1, 2014

By Victor V. Karmazin

"The appearance of the precise equipment for analysis of results of the laboratory tests with using of the computer processing allows raising accuracy of the estimation of the expected indexes of the mineral processing. Certainly, laboratory tests will not be able to substitute completely industrial ones, but allow reducing the amounts of the industrial tests, that vastly reduces the cost of technological forecast and preparation of data for projection.Calculation of the potential indexes of mineral technology (mass yields and the metal content in products) is fulfilled on the base of results of measurements of the mineralogical liberation parameters using special formulas.The quality of the concentrate ßc = a + ?l • ?s • ?i (ßt - a) can be achieved on a level of the theoretical metal content of a mineral - ßt only if coefficients of mineral processing, of liberation ?l and selectivity ?s of grinding, effectiveness of separation, will reach 1 (a - metal content of the row ore).Increase ?l by overgrinding automatically decrease ?s, and only by destroying of particles of ore along surfaces of accreting of minerals (?i = 1) and when values of all three coefficients will aim to 1, then ßc ? ßt.The degree of liberation of the useful mineral is the ratio of mass of free grains of the useful mineral in the product to general mass of the same mineral in this product. The factor of the liberation, which is defined by curves of dressability by angle of slop of the curve of the elementary faction - ?, is Kr=1 – tga. Kr changes from 0 to 1 when a changes from 45o to 0o. The liberation is reached by grinding of the material, although degree of the liberation, as a rule, is lower than the degree of the grinding."

Jan 1, 2003

By Graeme J. Jameson

In conventional flotation machines, the recovery is strongly related to particle size. As particle size increases, the recovery also increases, reaching a maximum in the range 20 to 120µm. Beyond this range however, the recovery declines quite quickly. The reason for the decline in recovery observed with coarse particles can be traced to the effect of turbulence. Bubbles trapped in turbulent eddies rotate rapidly, and when the centrifugal force on a particle exceeds the retaining forces due to surface tension, the particle detaches. Since the centrifugal force varies as the cube of the diameter of the particle, and the attachment force varies simply as the diameter, being proportional to the length of the contact line, it is clear that detachment forces will predominate as the particle size increases. The corollary is that the recovery of coarse particles can be improved if the level of the turbulence in the cell can be reduced to a minimum. In this paper, a new type of flotation machine will be described, in which the particles to be floated are suspended in a fluidized bed. An up flow of fluidizing water is provided, by recycling liquid from the top of the cell. The recycle stream is aerated in a high-energy device that disperses the air into fine bubbles that capture the fines and ultrafines. Results are presented for several minerals and coarse coal. Keyword: fluidized bed flotation

Sep 1, 2012

By I. N. Babich

"Complex technological problems associated with the processing of mineral raw materials require the search and development of new means and ways of thinking. At present, computer cognitive graphics (CCG) are one of the most actively developing areas of new information technologies. The aim of the study was to optimize the cycle of technological evaluation of ores at all stages of geological exploration of deposits on the basis of analysis of geological sampling data using CCG. A new approach has been developed that facilitates optimization of the whole cycle of subsoil exploration. At the gold ore deposit, the results of the geological sampling data were processed by the method of constructing the CCG in the form of a histogram showing the frequency of gold extraction and the average amount of its content. Significant peaks of the metal content in the ore, exceeding the level of the average content in the ore by tens of times, have been revealed. Graphical interpretation of the parameters of mineralization reflects the uneven nature of its variability, which indicates the presence of large, rarely occurs of gold in the ore and the need to conduct studies on a sample of ore of greater mass than for ores with tiny gold. On a sample of 50 kg gold-quartz ore studies were carried out on gravity enrichment. The maximum size found in the gold concentrate was 0.07 mm. In the course of integrated tests in a gravity concentrate, gold particles up to 3 mm in size were found, which predetermined the need to include the operation of gravity before flotation. A new approach to subsoil research is protected by a patent (RU 2620823).The technological problems that arise before the researcher associated with the processing of resistant ores require the exploration and development of new means and ways of thinking. New problematic situations on complex mineral and raw materials objects are practically not amenable to resolution by existing methods. Integration of industrial and information technologies is necessary. At present, computer graphics (CG) is one of the most rapidly developing areas of new information technologies. For example, in scientific research, including in fundamental research, the accent from the illustrative function of CG (the visualization of what is already known) is increasingly shifting towards the use of computer cognitive graphics (CCG) tools (Bashlykov, 2016). The function of the CCG is to obtain a new knowledge with the help of a graphic representation - a cognitive image or at least to promote the intellectual process of the logical acquisition of this knowledge. In this study, cognitive images are used to graphically represent the distribution of valuable components in the bowels of the deposit, characterizing the state of mineral-raw materials."

Jan 1, 2018

By M. Pelser, Lorenzen L.

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.A review of literature has proven that there is no conventional method for the control of calcium and or magnesium, although a number of potential processes have been identified. The technologies investigated included precipitation, ion exchange and solvent extraction, for which at least one method was found under each. To make the reader aware of these processes a short description was provided of each within the text.Of these processes, fluoride precipitation was selected for experimental investigation based on the low solubility of calcium and magnesium compared to the base metals. This process involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments were designed to investigate the equilibrium of the system at varying parameters of which the level of fluoride addition, the ratio of calcium to magnesium, and the identity of the soluble fluoride was reported. In all of the instances the process showed high selectivity towards calcium and magnesium over the base metals. The experiments proofed the process to have a higher affinity towards the removal of magnesium at compositions where the molar ratio of calcium to magnesium was higher than 1:3. It is often the case that the calcium to magnesium ratio is in the region of 1: 10. From this it follows that the fluoride addition has to be stoichiometric or greater for calcium and magnesium combined, if the calcium is to be precipitated. This was demonstrated as well. On the identity of the soluble fluoride hydrogen fluoride was compared to ammonium fluoride, of which the latter was found to be preferred."

Jan 1, 2003

By Markus A. Reuter, Jacques J. Eksteen

"The modelling of bath type furnaces tends to be either fundamental in nature or total empirical ""black box models"". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Not only are fundamental process relationships such the mass and energy balances satisfied through a scientific method of data reconciliation; the proposed modelling approach allows adaptive prediction, the first step towards predictive control or metallurgical decision support.It is shown that neither an ARMAX model only, nor a purely equilibrium model only, could predict the dynamics of the process very well. However, a combination of the two approaches more than doubled the accuracy as measured by the R2. It was noted for carbon dissolved in the alloy, that the improvement in R2 in using a hybrid modelling approach was more than the sum of the R2 of the individual traditional approaches. Similar improvements in modelling performance were noted for all other species.It shows further that process dynamics may totally overshadow the effect of thermochemical equilibrium (even when the thermochemical equilibrium prediction includes the recycled alloy and slag heels as additional feeds). The exclusion of process dynamics therefore leads to erroneous results."

Jan 1, 2003

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

"A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change because of the strong path dependency of industry and infrastructure development. The metal production network is complex, as it consists of an interconnected and integrated system that incorporates multiple production routes for a spectrum of metals. More often than not, the production or recovery of a single metal is related to or dependent on the generation or recovery of another. The effects of these other metals is of great importance. In order to realize the potential economic importance of impurities, research and development have integrated the processes of copper production with those of lead and zinc, and connected the processes to those of among others silver, bismuth, tin and platinum group metals (PGMs), for example. The recovery of these elements from the interconnected circuits is extremely complex, as most of the elements must be circulated between two or more circuits before they are concentrated enough to make their extraction possible, and their recovery as a compound profitable.From such a system’s perspective, it can easily be seen that a complication for solid waste management has arisen through the development of products (consumer goods) that bring together metals that are not linked in natural resources. As a consequence, many of these materials are not compatible with any process in the metals production network that was developed for the processing of primary, natural resources, optimized for the processing not only of the primary metal but also for all mineralogically associated minor valuable and harmful elements. The formation of large or complex residue streams or undesired harmful emissions then inhibits processing and recovery of said products at their end-of-life. Another complication is that any change to the system (in metal production, SWM or product design) affects the system configuration. Due to the changing demands for metals as a result from the changing products made from the metals for example, the relationships between the processes in the interconnected metal production systems change. This affects both the demand for old scrap (required amount and grade) from waste management, and the environmental profile of the metals. Preferably, therefore, product designers, waste processors and metal producers must cooperate to realize optimal metal recovery in processing discarded consumer products."

Jan 1, 2003

By John Starkey

"The development of the SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.Previously, it was deemed prudent to select up to 50 t samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5 t sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50 t sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By R. Els Ellis

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By J. Kwon, D. Lee, H. Cho

"The use of the combined grinding and liberation model to predict liberation characteristics of iron ore comminuted by a ball mill was studied. Comminution characteristics were obtained using the one-size fraction method. The iron ore samples were crushed and separated into a number of narrow size fractions by screening. The size fractions were further divided by magnetic separation into three classes: concentrate, middling, and tailings. Subsequently, various size-grade classes were subjected to ball milling, and the results were analyzed in terms of the kinetic grinding model. The mineralogical textures of the grinding products were analyzed using mineral liberation analysis. The distribution of iron content within the size fractions was characterized by the beta distribution combined with the Andrew–Mica diagram. It was found that the grinding characteristics of the iron ore samples varied slightly with the iron content. However, the liberation characteristics were well described by the same set of liberation model parameters, regardless of composition. The variation in grinding kinetics with composition and the liberation model parameters was used in the combined comminution–liberation model to predict the evolution of the size-composition matrix as grinding proceeded. The predicted results agreed well with the experimental results. The developed model can be used to construct the yield–recovery graph and to calculate the liberation efficiency to determine the size reduction threshold for efficient separation. INTRODUCTION In mineral processing, comminution is usually the first step that ores undergo to liberate valuable minerals from gangue minerals. Generally, as the particle size decreases, higher liberation can be achieved. However, excessively small particles are unfavorable to subsequent processes, such as separation. Moreover, comminution is a highly energy-consuming process itself that accounts for approximately 60% of all energy used for processing. Therefore, there is a definite need to increase energy efficiency by applying adequate stress so that a high degree of liberation can be acquired at the coarsest size without overgrinding. To this end, it is essential to develop a model to predict the liberation of minerals as a function of size reduction."

Jan 1, 2018

By M. Ghiani, P. Massacci, A. Manni, R. Peretti, Center for Mining and Mineralurgical Studies, S. Serranti

"The research study has been devoted to point out the better way to process a colemanite concentrate characterised by a high content of two kind of As sulphides (realgar and orpiment) finely disseminated in the matrix of the boron mineral.Scanning Electron Microscopy analyses have been carried out to determine all the mineralogical constituents and to evaluate their distribution, frequency and mutual relationships.There is a not neglectable part of realgar highly disseminated into the colemanite crystals.The orpiment recurs in small acicular crystals of 20÷30 µm in length and 5 µm in width, very difficult to liberate from the colemanite mineral particles.The colemanite concentrate, in fact, has been addressed to a chemical plant which products were boric acid and gypsum, the contaminated by As. It was unacceptable for further applications and very dangerous if rejected in the environment.Grinding tests under dry and wet conditions have been carried out in order to evaluate the liberation modality of the As sulphide minerals from the colemanite.Some difficulties have been overtaken in order to obtain a selective liberation of the As sulphides from the colemanite even if a certain decreasing in As grade in the higher size classes has been registered.All the comminution products have been analysed by SEM monitoring the liberation degree of the mineralogical constituents.Flotation tests have been carried out after different comminution flow sheet adopting different modulating conditions in order to evaluate the influence of the following parameters:• collector concentration versus contaminants concentration (As minerals) in the froths;• kind and quantity of the frothing agent to maximise the mineral recovery in the froths;• kind and quantity of the modulating agents to maximise the selectivity of the process;• conditioning modalities in order to obtain a suitable dispersion of fines and to avoid segregation of Asbearingparticles together with colemanite ones;• solid/liquid ratio of the pulp to minimise the water flow into the plant."

Jan 1, 2003

By P. Saha, D. M. Chakrabarti, National Metallurgical Laboratory, P. Bhattacharyya, B. R. Sarkhel

The estimated reserve of the phosphatic soils at the Sukulu hills region of Uganda upto a depth of 60 meters is of the order of 200 million tonnes and analyses 10-12% P2O5. A 5-tonne sample of the phosphatic soil was received at the National Metallurgical Laboratory (NML), India for beneficiation studies. The ore occurred as a naturally degraded soil deposit and the slime contained earthy lateritic minerals which made it extremely sticky. Microscopic examination revealed the presence of limonite, magnetite (martitised), hematite and goethite as major minerals along with apatite and quartz. Presence of clay was indicated by earthy smell on moistening the sample. It was observed that getting rid of the slime was as important for adequate beneficiation of the ore, as it was difficult. Earlier studies on samples of the same ore at the NML and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of rigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slimy coating which stubbornly adhered to mineral grains. Studies were carried out at the NML in two phases to develop a flowsheet for beneficiation of the phosphatic soil. In the first phase, reproducibility of the results obtained by employing a flowsheet developed abroad was confirmed along with suggesting some modifications of the flowsheet. Then 200 kg. of concentrate was produced following the recommended flowsheet for evaluation of its suitability for production of fertilisers. To remove the limonitic slimy coating, which stubbornly adheres to the other mineral grains, it was necessary to subject the ROM ore, after screening out the +840 micron size fraction which contained only 1.75% P2O5 , to three stages of hydrocycloning each preceded by attrition scrubbing. Then only conventional beneficiation techniques could be effectively employed to upgrade the ore.

Jan 1, 2003

By Daniela Campos, Aldo Casali, Gonzalo Montes-Atenas

The understanding of the effect of the major variables influencing the froth flotation performance may allow both to predict and to identify best operating conditions towards optimizing the process efficiency. The aim of this research work is to model the effect of dissolved oxygen onto froth flotation performance. Experimental pilot plant results were obtained from a continuous circuit consisting of a ball mill and a rougher bank of four flotation cells. A series of flotation experiments were run with different conditions of dissolved oxygen keeping constant most of other operating conditions. Variables difficult to control were measured or estimated. A set of mathematical models suggested in the published literature were tested. It was found that the copper recovery results were highly sensitive to the concentration of dissolved oxygen. The latter confirmed the reactions mechanisms associated to the collecting capabilities of current flotation reagents used in the flotation of copper sulfide ores. On the contrary, the results of molybdenum recovery varied non-linearly with changes in dissolved oxygen which could not be explained directly in terms of the computed specific rate constants. The error analysis confirmed that Klimpel continuous model exhibited the best specific rate constant correlation with molybdenum recovery data. Lastly, the classic particle force balance equations indicated that the adjustments of estimated mineral liberation with experimental data exhibited a turning point when passing from highly liberated to low liberated particles. The values of recovery for such turning point correlated well with the concentration of dissolved oxygen. The results indicated corrections due to changes in the dissolved oxygen must be incorporated in future froth flotation descriptions.

Jan 1, 2014

By J. Broadhurst

"A number of metal supplying industries have in recent years seen the compilation of life cycle inventories (LCIs) and life cycle assessments (LCAs). The activity has largely been driven by the interest of ultimate metal users, such as the automotive industry, in the interest of designing more sustainable products. Often, the compilation of such inventories has been little more than an auditing exercise. However, the process of conducting an LCA can have more value, guiding designers and operators to points within the technology train where significant emissions and impacts originate. The LCA product can thus be used to inform on-site environmental management, and, where process data is used to construct dynamic operational models, to support strategic decision making in the realm of project planning and technology selection. LCA thus serves as a valuable tool to support the industry’s drive to support the sustainable development of the societies in which it operates.This paper reviews and compares the priorities of environmental and closure planning in the design phase, with environmental management and auditing during operation, and with green procurement of minerals and metals products. It shows how life cycle assessments of various complexities can be used to reconcile these various objectives, ensuring that the latter, critical to business success, can be addressed from the outset in a new project. The paper then reviews a case study of the use of LCA in the base & precious metals industry, where the complexity of the operation disallowed the simpler auditing process so that a detailed process understanding had to be built up in order to compile a meaningful life cycle inventory."

Jan 1, 2003

Dielectrophoresis is a separation technique that uses a non-uniform electrical field to separate particles on the basis of their permittivity. There are many areas of mineral processing that might benefit from the application of dielectrophoresis. These include: coarse removal of gangue, recovery of ultrafine particles, upgrading of flotation concentrates or simply as a laboratory analysis technique. In order to determine the potential value of dielectrophoresis to the mineral processing industry, the response of composite particles was investigated. The electrical properties of composites involve complex relationships between the shape, distribution and permittivity of the individual grains within the rock. The relationship between mineral composition and dielectrophoretic force was measured on single particles from two ore types. The results were used to populate a model that could predict the separation characteristics of the ore. The insights gained from this model separator allowed potential applications of the technology to be examined and their performance evaluated.

Sep 1, 2012

By Sudhir Srivastava

India hosts a wide range of globally significant mineral resources, including four fuel minerals; 11 metallic minerals; 22 minor minerals and 52 non-metallic minerals. The country ranks among world?s top five nations for its commodity reserves of coal and iron ore. Interestingly, only small part of country's landmass has been explored that provides opportunity for future substantial mineral discoveries. India plans to double infrastructure investments to US$ 1trillion. Despite the challenges in infrastructure project implementation, mining sector remains a key driver of demand growth for commodities in the years to come with a good prospect to grow in future.

Sep 1, 2012

By Verónica Fernández, Jaime Solari

"The Chilean Environmental Impact Assessment System (EIAS) of investment projects was created in 1994, date in which the General Environmental Law was enacted. The compulsory environmental approval of projects began in 1997 when the Regulation (S.D. 30/97) was officially issued. By beginning late to regulate the environmental effect of investment projects, Chile could take advantage of the international experience in the matter and therefore, the EIAS has many of the attributes of successful environmental assessment systems elsewhere. Thus, the main characteristics of the Chilean EIAS are: preventive, single-window, specific to certain projects, multi-agency assessment at the regional scale, 3 kind of applications, deadlines, citizen and native communities participation, link to relevant permits, definite conditions of approval/rejection, review of applications by an ad hoc institution. The Chilean EIAS has allowed during the period 1997-2013, the review of 21,110 projects for a total investment value of US$ 408 billion, of which a 76% have been approved. In the case of the mining projects, the corresponding figures for the similar period are 1,257 projects for a total investment value of US$ 119 billion, of which 78% projects were approved. The experience derived from the environmental impact assessment of mining projects indicates that Chile has been successful in linking together mining development with environmental protection. There is still little prejudice against mining and this is a still a largely welcome economic activity at all levels in the relevant regions of the country. The challenge that mining companies face today in Chile is to improve the sustainability of projects and operations, by learning to share scarce and valuable resources (water, glaciers, renewable energy) with the local and native communities, through a process of dialogue whereby mining development also generates benefits for these communities."

Jan 1, 2014

By Graeme Jameson

"In current flotation circuits it is customary to grind the whole of the mill feed to an initial size, which is determined by the liberation characteristics of the ore, and the ability of the flotation machines to float the fully liberated particles. Usually, the product of the primary mill will be ground further in a ball mill, to improve the liberation of the values and hence the product grade, before passing to rougher flotation cells. The final grind size is ore-dependent, and is a balance of factors including the relation between surface liberation and grind size, the grain size of the valuable particles within the host rock, and the feed grade. The P80 for the feed to flotation may be as high as 300 µm for free-milling copper ores, and as low as 53 µm for finely disseminated complex ores. The grinding of the feed ore requires considerable input of energy. The rate of replacement of wear components such as mill liners and media, is proportional to the energy input. The costs of these two factors - energy and wear - are usually comparable and together they form the major part of the running costs of a concentrator, and indeed, of the whole mining operation. The energy required increases as the final grind size decreases. This talk will focus on the reduction of milling costs that could be achieved, using a fluidized bed flotation technology that can give high recoveries at coarse particle sizes. A number of different circuit designs will be presented, using the new technology. Calculations show that reductions in the running costs of a mine and associated concentrator of the order of ten to twenty percent could be achieved."

Jan 1, 2014

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003