Search Documents

By William Siapno

Manganese nodules, as metal ores, have for the most part been cast aside from further consideration within this century. However, in the decade of the 90s, rising demand at all levels of society, for clean air give nodules a new - lease on life as a stack gas cleaning agent. Further, the Clean Air act of 1990, mandates enormous outlays to bring systems into compliance with new stringent standards. Quick corrective actions are imperative. Research beginning in the 1960s proved nodules possess unique qualities to remove acid compounds from stack gases. Early this year, the National Science Foundation awarded General Electric an $83 million contract to design a system to extract oxides of sulfur and nitrogen from coal fired power plants. Environmental damage is abundantly evident on the ground, from the air as well as form space. A dirty pall of yellow-brown smog is smothering both animal as well as plant life around the globe. Losses run into billions!

Jan 1, 1991

By Johnson R. Cann

Ocean floor sulfide deposits are now known from many parts of the world mid-ocean ridge system and from some seamounts. Clearly they can be expected to occur commonly on the ocean floor. However, only two or three of the known deposits appear to approach the million-ton size, and in none of the deposits has the grade been well-defined. Can knowledge of the processes that happen within the hydrothermal plumbing below deposits help define the conditions under which large, high-grade deposits form? Here I review present knowledge of ocean-floor hydrothermal processes to attempt a first answer to this question. There are three sources of information about these processes. The solutions emerging from active systems must be compatible with patterns of alteration that underlie the volcanogenic sulfide deposits of ophiolite complexes, which are slices of ocean crust thrust onto land. Both of these types of evidence can be linked by computer modelling of the exchange of heat and metals between rocks and flowing water.

Jan 1, 1988

By I. Yu. Melekestseva

The Semenov hydrothermal sulfide cluster (13º31´N), consisted of five fields (Semenov-1, -2, -3, -4, and -5), was discovered in 2007 in the 30th cruise of R/V Professor Logatchev [Beltenev et al., 2007; 2009]. The hydrothermal fields are located on a seamount composed of ultramafic and mafic rocks, gabbro, plagiogranite, and their altered rocks. The Semenov cluster is considered to be the largest sulfide accumulation in the Ocean with massive sulfide (MS) resources of about 40 million tons [Beltenev et al., 2009]. MS of the Semenov-1, -3, -4, and -5 hydrothermal fields are mostly characterized by marcasite-pyrite composition whereas rich copper-zinc MS with high Cu and Zn contents (11.37?19.33 and 5.89?18.32%, respectively) and anomalous Au and Ag grades (22?188 ?127?1787 ppm, respectively) were dredged only at the Semenov-2 hydrothermal field associated with basalts (13°31.13´N, 44°59.03´W; 2360?2580 m of depths) [Ivanov et al., 2008].

Jan 1, 2010

By Igor E. Mikhaltsev

The goal of investigation of the midwaters and of the bottom of the world - ocean versus technological possibilities. Manned vehicles and maximum depth decision. The methods of solving of the problem. The science and technology alloy. Mutual venture of Academy of Sciences of the USSR and, Rauma-Repola Oy of Finland. MIR-1 and MIR-2 - as twins. No reasons of copy "Sea Cliff" and "Nautilus". Six landmarks of specificity of "MIR"-type submersibles. The manned spheres and three ballast spheres are made of maraging steel; the electric power resource (100 kwh) and maximum underwater speed (5 knots) is two times more than of the analogous vehicles while the batteries are of NiFe type; the MIR submersibles have the seawater ballast (and trim) system which means practically unlimited vertical manoeuvrability ; and the weight in air is equal to "Nautilus" - 18,6 tons (in case of equal energy resource the weight of MIR-1 or MIR-2 would be 17 tons). Some remarks on standard life support (248 man-hours) safety systems and specificity of launch & recovery system.

Jan 1, 1988

By Peter A. Rona

Hydrothermal mineralization along slow-spreading oceanic ridges and rift -zones that comprise more than half the global length of the seafloor spreading center system is related to anomalous physical and chemical conditions acting within the geologic settings that characterize early and advanced stages of opening of an ocean basin. Mineralization in the early stage of opening is represented by the Atlantis II Deep of the Red Sea. There, hypersaline hydrothermal solutions discharging as density stratified brines into an axial basin, have formed the largest massive sulfide deposit (70 x 106 metric tons) known at a spreading center. Mineralization at the advanced stage of opening is represented by two types of sites: (1) oceanic crust on the wall of a rift valley; and (2) oceanic crust exposed on the wall of a transform fault zone. The first type of site is the TAG Hydrothermal Field, located on a wall of the rift valley of the Mid-Atlantic Ridge at the top of the basaltic layer of oceanic crust. Evidence is presented for multi-stage, high- and low-temperature hydrothermal activity that produces Cu, Fe, and Zn enrichments within the thin sediment column and stratiform interlayered deposits of manganese oxides, iron oxides, hydroxides and silicates, on the seafloor. The second type of site occurs along walls of transform fault zones of the equatorial Mid-Atlantic Ridge and Carlsberg Ridge, which exhibit stockwork-type Cu-Fe sulfide mineralization

Jan 1, 1985

By Ian J. Graham, Cornel E. J. de Ronde

New Zealand lies astride a convergent plate boundary that extends north-eastwards from the Taupo Volcanic Zone (TVZ) to Tonga. This boundary is marked by the Kermadec arc, c. 1200 km of which falls within New Zealand’s EEZ, and which is host to numerous volcanic edifices both on the arc and in a zone immediately behind the arc to the west. In 1999, thirteen volcanic centres in the southern 260 km of the arc were surveyed for their hydrothermal plumes with seven of them discharging vent fluids into the surrounding ocean. Three of the seven volcanic centres have had mineralised rocks recovered from them during dredging and submersible operations, namely Brothers, Rumble II West and Clark. Presentday plume data combined with mineralogical evidence indicate that the vent sites at Rumble II West and Clark are waning, although the presence of Cu-rich sulphides in samples recovered from Rumble II West suggest there may be a massive sulphide (Cu-Zn-Pb-Ba ± Au) deposit located within the caldera. Brothers volcanic centre is host to the largest polymetallic mineral deposit discovered along the Kermadec arc and has numerous, up to 7 m tall chimneys within a c. 600 x 200 m area located on its NW caldera wall. Geochemical data indicate that concentrations of base metals are variable and depend critically on sample type. When combined with mineralogical and plume data, this indicates addition of a magmatic fluid component to the vent fluids.

Aug 24, 2006

By T. Kuhn

The Logatchev hydrothermal field is situated on the east inner flank of the rift valley of the MAR at 14°45?N and is hosted by serpentinized peridotites and minor gabbronorites while basalts are subordinate. Hydrothermal precipitates recovered from the Logatchev field during a recent R/V Meteor cruise include massive chalcopyrite chimneys, massive pyrite crusts, silicified breccias, abundant secondary Cu-sulfides, red jaspers, abundant Fe-Mn-oxyhydroxides as well as atacamite and Mn-oxides (Kuhn et al., 2004). Previous results of hydrothermal fluid studies in the Logatchev field are somewhat at odds with theoretical models of ultramafic-seawater reaction. Butterfield et al. (2003) suggested that the Fe component of orthopyroxene plays the more important role compared to olivine in ultramafic-hosted hydrothermal systems. This consideration is supported by the recovery of large amounts of Opx-rich gabbronorites and orthopyroxenites in the Logatchev field (Kuhn et al., 2004). A possible tool to constrain the contribution of the different rock types (ultramafics, mafics, MORB) to a seafloor hydrothermal system is the systematic analysis of 187/188Os ratios of the host rocks as educts and the sulfides as products. For instance, abyssal peridotites mainly display low 187/188Os ratios (<0.127); in contrast MORB and gabbronorites have radiogenic ratios of >0.13 (Snow and Reisberg, 1995), orthopyroxenite has ratios of about 0.174 (Büchl et al., 2002) and seawater has an ever higher 187/188Os of about 1 (Sharma et al., 1997). Therefore, massive sulfides predominantly leached from ultramafic rocks should have Os isotopic ratios plotting on a mixing line between the ultramafic rocks and seawater (in a 187/188Os vs. 1/Os diagram), whereas those derived from MORB, gabbronorites and/or orthopyroxenites will be plotting on different mixing lines.

Jan 1, 2004

By David A. Clague, James R. Hein, Robert W. Embley, Robert C. Vrijenhoek, Randolph A. Koski

We report preliminary results for a group of unique samples collected with MBARI’s ROV Tiburon on August 12, 2005. The samples were collected from the East Blanco Depression (EBD) diffuse-flow hydrothermal field, which was determined in a previous study to cover an area of at least 100 m by 80 m (Hein et al., 1999). The survey reported on here extends that field to more than 1500 m in an approximately N-S direction. The EBD, a pull-apart basin, occurs near the western end of the Blanco Fracture Zone (BFZ), which connects the Juan de Fuca and Gorda Ridge spreading centers (Fig. 1). The samples were collected from a waterdepth range of 3343-3380 m.

Aug 24, 2006

By Hyung-woo Kim

This paper concerns about steering characteristics of pilot mining robot, named MineRo II, crawling on extremely cohesive soft soil using dynamic simulation software. The MineRo-II for deep-seabed manganese nodules, which aims at the use for pilot mining test, was manufactured in 1/5 scale of commercial mining capacity (see Fig. 1).

Sep 14, 2011

By Jan M. Peter

Many of the Pb-Zn massive sulfide deposits of the Bathurst area in northern New Brunswick, Canada, are intimately associated with laterally continuous iron formation (IF) (Figure 1). This IF is a fossil laminated, exhalative, chemical sediment. Together, the IF and the Brunswick #12, Brunswick #6, and Austin Brook deposits (rightmost discontinuous horizon on Figure 1) are collectively referred to as the "Brunswick Belt". To date we have only studied the Brunswick Belt and have not examined the horizon along which the QSR, CNE and Flat Landing Brook deposits lie. The Bathurst area is underlain by the Tetagouche Group (Figure 2), a Cambro(?)-Ordovician sequence of metasedimentary and bimodal metavolcanic rocks that was intruded by mafic to felsic plutons and subsequently deformed during the Taconic Orogeny. The stratigraphic sequence consists of shales and greywackes that are overlain by carbonaceous shales and felsic volcanic and volcaniclastic rocks; these are in turn overlain by mafic volcanic and sedimentary rocks. The massive sulfide deposits and IF occur within the upper portions of the felsic volcanic rocks in close association with carbnaceous metasedimentary footwall rocks (Figure 2).

Jan 1, 1993

The chemical composition of the nodules varies with the type of manganese minerals and the size and characteristics of their nucleus, but those who have an economic interest have the following composition: Mn 29%, Fe 6% Si 5%, Al 3%, Ni 1.4%, Cu 1.3%, Co 0.25%, Na 1.5%, Ca 1.5%, Mg 0.5%, K 0.5%, Ti 0.2 0.2% and Ba 0.2% (Morgan, 2000; ISA, 2002). The Pacific Rim is an area of abundant occurrence of polymetallic nodules (Glasby et al., 1980; Morgan, 2000). According to these authors, the Pacific sea floor of the Clarion-Clipperton Zone (CCZ) is one of the most interesting areas in regard to the genesis of polymetallic nodules. Their abundance in the ocean floor is very variable, as there are places where they cover more than 70% of the ocean floor. The nodules can be found at any depth, but the highest concentrations are between 4000 and 6000m (Morgan et al., 1993). In studies conducted in the EEZ of the Mexican Pacific are those made within the project "Research on the origin, process and distribution of minerals in the Pacific ocean floor in the Exclusive Economic Zone of Mexico". Within this project Rosales (1989) conducted studies on the origin, process and distribution of polymetallic nodules, finding that a number of processes give origin to nodules, being diagenesis one of the main mechanisms of elements that contribute to the nodules. Besides hydrothermal processes that are carried near the East Pacific Rise at 21° N, inputs are contributing to the nodules metallic elements and sediments, especially in regions close to the dorsal, as a greater influence hydrogenetic processes occurs westward (Rosales and Carranza, 1990). In 1993, after cruise MIMAR II, Carranza and Rosales refer that metals such as Cu, Co, Ni, Sn, Fe, Mg, Pb, Zn and Ba may have a relationship with the East Pacific hydrothermal activity and sea currents carry these metals in solution to the Clarion-Clipperton fracture area, where there are hydrogenic metals sources (Al, Fe and Mn). As result of chemical analysis of Mn, Cu, Ni and Co, polymetallic nodules observed in part of the EEZ of Mexico are possible of potential economic interest (Rosales and Carranza, 1990, 2001; Carranza and Rosales, 2003).

Sep 14, 2011

By Tetsuo Yamazaki

The Kuroko-type seafloor massive sulfides (SMS) in the western Pacific have received much attention as sources for economic recovery of gold (Au), silver (Ag), copper (Cu), zinc (Zn), and lead (Pb). Since the end of the 1980s, the Kuroko-type SMS have been found in the back-arc basins and on oceanic island-arc areas. In Okinawa Trough (Halbach et al., 1989) and on the Izu-Ogasawara Arc (Iizasa et al., 1999) are the typical representatives in the Japan’s EEZ. They yield a higher concentration in Au and Ag than the SMS found in ocean ridge areas (Rona, 1985). Similar formation processes with the Kuroko ore deposits on-land in Japan have been expected and outlined by many researchers (Sillitoe, 1982; Scott, 1985). The higher Au and Ag contents have increased the chances for profitable mining operation, which is under consideration by a private company (Malnic, 2001). Information about the resource potential of the targeted Kuroko-type SMS deposit, such as the amount of SMS ore body, the inside structure, the mean metal yields, and the geographical details are necessary for a technical and economic validation analysis for the development. The Sunrise Deposit of Myojin Knoll on Izu-Ogasawara Arc in the Japan’s EEZ is selected as a target for the technical and economic validation analysis. The relatively higher amount of information on its resource potential is the reason why the deposit is selected.

Sep 24, 2006

By Ivo Dreiseitl

The interaction between nodule harvester and eupelagic sediment on the seabed is definitely one of the key aspects of mining technology for polymetallic nodules which is to be studied in details. Physical properties of sediments play major role for evaluation of protection and preservation of marine environment while strength properties of sediments will come in useful for future mining operations. Cone penetration test (CPT) used for testing in situ is one of methods for investigation strength properties of sediments. The testing apparatus for CPT consists of an instrumented cone having a tip facing down and it is mounted on special underwater equipment (rus. UGI-1). UGI-1 can determine subsurface strength down to the depth interval 0 ? 1.10 m. Special IOM geotechnical cruise was accomplished in 1989 on board R/V Academic A. Karpinski within the extra test area of about 1000 km2. Thanks to UGI-1 the IOM database recorded unique strength sediment data (cone penetration resistance) from 279 seabed points of sounding at profiles 125.6 km long. Up to 35 strength data from depth interval 0-1.1m (every 3cm) were obtained from any particular testing point. As a result 279 strength charts could be plotted (two examples in Figure 1). The cone penetration resistance values can be correlated to shear strength parameters.

Jan 1, 2011

By T. Semkova, G. Cherkashov, V. Rashidov, L. Anikeeva, G. Gavrilenko, G. Glasby

The Kurile Arc consists of at least 100 submarine volcanoes and 5 submarine calderas located mainly in the rear arc (Figure 1). The arc is seismically very active, particularly in the south, and is characterized by extensive volcanism and hydrothermal activity. At least one subaerial volcano on the arc (Medvezhy located on Iturup island) has an extremely shallow magma chamber and is intensely active.

By Robert G. Ditchburn, Cornel E. J. de Ronde, Bernard J. Barry

The age of mineralization, its mode of formation, the time elapsed to amass an economic deposit, its capacity for sustainable extraction and, ultimately, its grade and tonnage, are key aspects in the economic viability of volcanic massive sulphide (VMS) deposits (Ditchburn et al, 2004). Radiometric dating methods applied at GNS Science have been recently refined with the purpose of efficiently determining the ages of seafloor VMS mineralization along active intraoceanic arcs. These developments include: determining the longevity of seafloor hydrothermal systems, details of individual chimney and massive sulfide mound growth, and insights into deep-seated processes, such as the transfer of elements from magmas to their overlying hydrothermal systems. In our pursuit to better understand seafloor hydrothermal systems along intraoceanic arcs, we have thus far compiled age information for three volcanic centres of the Kermadec arc (South Pacific) and one of the Mariana arc (NW Pacific).

By J. R. Hein

East Diamante is a submarine volcano in the southern Mariana arc that is a complex caldera about 10 km x 5 km (elongated ENE-WSW), and breached on its northern and southwestern sectors. A large field of barite-sulfide mounds was discovered in June 2009 and revisited in July 2010 aboard the R.V. Natsushima using the Hyper-dolphin ROV. The mound field occurs on the NE flank of a cluster of resurgent domes inside the caldera. The mound field extends for more than 100 m long and is about 30 m wide, and is aligned along a NE-SW rift valley. A sample of dacite yielded a 40Ar/39Ar age of 20,000±400 years. Individual mounds are typically 1-3 m tall and 0.5-2 m wide, with lengths from about 3 to more than 5 m. The mounds are composed of barite-dominant layers interbedded with Zn-sulfide-rich barite layers. Rare inactive spires and chimneys cap some mounds. Fe and Mn oxides are currently forming small (<1 m diameter, ~0.5 m tall) subsidiary mounds on the top of some of the sulfate/sulfide mounds and drape the flanks of others. Both diffuse- and focused-flow fluids emanate from the subsidiary oxide mounds. Ages of the basal sulfate/sulfide mounds cluster around 4,000 years old based on 226Ba/Ba, whereas the oxides are less than 5 years old based on 228Th/228Ra. Most mound and chimney samples are dominated by barite and amorphous silica; sulfides occur in variable amounts that in decreasing order of abundance include sphalerite, galena, pyrite, and chalcopyrite. Anglesite, cerrusite, and a Pb phosphate occur as late-stage interstitial phases. Some mound samples have fragmental textures; layered clasts composed of chalcopyrite and pyrite may have been derived from collapsed chimneys. Despite the abundance of barite, samples contain high concentrations of Zn (to 23 Wt.%), Pb (to 13 wt.%), Ag (to 500 ppm), and Au (to 15 ppm). Copper is enriched in a few mounds samples, up to 3 wt.%, but is typically <1 wt.%. Other significant metal enrichments include Sb (to 1320 ppm), Cd (to 1180 ppm), and Hg (to 55 ppm).

Jan 1, 2011

By Yuta Yamamoto

Seafloor massive sulfides (SMS) which contain Au, Ag, Cu, Zn, and Pb have been interested in as a target of commercial mining these 15 years. Japan has large potential of SMS and a national R&D project for the mining has been active these 5 years. However, the economy of SMS mining is very bad, because the waste tailing disposal cost is very expensive in Japan. A slurry flushing method is experimentally examined in this study for the improvement of the economy. During the flushing, because of density difference between the metal-rich ore and the waste rock, a kind of gravity separation is possible. The results suggest a possibility of the actual application.

Sep 14, 2011

By Mikhail D. Ageev

The paper concerns with some questions of Autonomous Underwater Vehicle (AUV) control system design, which allows a motion at rough undersea terrain. The AUV advantages reveal itself completely during exploration of such objects as seamounts and reefs area. These objects are characterized by steep slopes (30 degrees and above) and chaotic situated obstacles (rock debris, pinnacles, escarpments). Uses of other technical facilities for operating in such formations are difficult, dangerous or impossible. These regions take an interest due to the presence of iron-manganese crusts. Modern AUV can estimate density of mineral by means of still camera or video recorder. For this reason the vehicle has to move with the distance of 3-5 meters from seabed. Under such conditions micro- and mesorelief presents a considerable danger for AUV. The AUV can bypass underwater obstacles in the various ways. However, in any case AUV motion will be characterized by intensive maneuvering on various speed (from 0 up to 1.5 m/s), circular change of tractive force vector and, hence, a circular flow about the hull. So, AUV is equipped with the propulsion system, which provides free modes of motion. AUV control system (CS) has tri-level structure to allow a motion in a rugged seabed terrain. According to the generally accepted categorizations, CS includes execution, coordination and strategic levels. The strategic level contains the goals of AUV mission. Obstacles avoiding and route choice are realized by means of simultaneous maneuver in vertical and horizontal planes. Sonar system is used for data acquisition about obstacles. It consists of a few echo-sounders with fixed directivity pattern. The route choice algorithm operates at two lower levels of CS. Basic (?reflex?) functions of spatial motion are realized within the execution level and considered in the paper. The choice of motion modes is carried out at the coordination level of system. All accessible navigating information (the data from flight sensors and from multichannel echo-sounder systems) is used for this purpose. In addition the bypass of characteristic types of obstacles is carried out with the help of basic motion modes combination. The modeling results of bypass of various typical obstacles, and also their combinations are described in the paper.

Jan 1, 2011

By Sup Hong

Herein, concept designs of two different types of mining robots are concerned, which are aimed for developments of deep seabed mineral resources: polymetallic nodules (PMN) and seabed massive sulfides (SMS), respectively. Continuous mining concepts are presented based on technical and environmental feasibility, where the environmental and functional differences for commercial productions are investigated. Needs and roles of versatile mining robots are explained as a key of continuous mining system. The functional requirements and design characteristics of mining robots to satisfy the top requirements from customers are described comparatively. Schemes of axiomatic design and quality function deployment (QFD) are utilized: functional requirements (FR) are defined, technical requirements (TR) are figured out, design parameters (DP) are derived, and degrees of importance of design parameters are evaluated. Analogy and discrepancy in remote operation methods are put side by side. A pilot scale mining robot for PMN and a commercial scale one for SMS are suggested in form of concept designs. PMN mining robot is shaped as a multiple configuration of unit robot modules in side dimension, in which the unit robot module consists of two tracks and two pick-up modules. SMS mining robot is based on a four-tracked vehicle. Main platform is mounted on the vehicle through turn-table. Excavation device consists of two-articulated boom and cutter tool. Crushing-and-pumping units are placed same in both robot platforms.

Jan 1, 2011

By Mikhail D. Ageev

The paper concerns with some questions of Autonomous Underwater Vehicle (AUV) control system design, which allows a motion at rough undersea terrain. The AUV advantages reveal itself completely during exploration of such objects as seamounts and reefs area. These objects are characterized by steep slopes (30 degrees and above) and chaotic situated obstacles (rock debris, pinnacles, escarpments). Uses of other technical facilities for operating in such formations are difficult, dangerous or impossible. These regions take an interest due to the presence of iron-manganese crusts. Modern AUV can estimate density of mineral by means of still camera or video recorder. For this reason the vehicle has to move with the distance of 3-5 meters from seabed. Under such conditions micro- and mesorelief presents a considerable danger for AUV. The AUV can bypass underwater obstacles in the various ways. However, in any case AUV motion will be characterized by intensive maneuvering on various speeds (from 0 up to 1.5 m/s), circular change of tractive force vector and, hence, a circular flow about the hull. So, AUV is equipped with the propulsion system, which provides free modes of motion.

Jan 1, 2003