Search Documents

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By Albert Neumann, Franz-Werner Gerressen, Giancarlo Santarelli

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. In addition they are also quite often used as deep groundwater barriers, named Cut-Off-Walls (COW). Due to the requirements of each particular job site, e.g. the need for carrying high loads or as seepage barriers, there is an increasing industry demand for efficiently cutting into rock. Besides the removal of boulders, cutting through rock, is always the most difficult part of the excavation process of a diaphragm wall or COW.There are a number of influencing factors which have an impact on the rock cutting performance. Besides the influence of the rock characteristics itself, which is not always the same, there are other factors related to equipment, tooling as well as the operating staff. In addition to RQD, the most commonly available rock property found in geotechnical reports is the Unconfined Compressive Strength (UCS) value. There are however some other related properties, such as weathering, bedding, inclination, abrasiveness, etc.,which can have a major impact on the achievable cutting performance. This paper will discuss the various parameters, and how they can be considered for performance estimation. Based on experiences gained on over 100 projects, a performance estimation chart was developed to allow for a better approach to these kinds of projects. This paper also explains the general installation process in as well as some specific features related to specific site conditions. In addition, some job site references will give more detailed information about such type of site conditions and how to deal with them.Keywords: Diaphragm wall, Cut-Off-Wall, Trench Cutter, RockINTRODUCTIONDiaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits, shafts, permanent foundation walls and load bearing elements.It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions.In addition diaphragm walls can also be used as deep groundwater barriers (Cut-Off-Walls). This market has demonstrated that the demand for these types of walls is reaching ever more difficult soil conditions and greater depths which are surpassing the current industry standards. The trench cutter is the most important tool for performing this type of work."

Jan 1, 2016

By Brandon Buschmeier, Frederic Masse

"Inclusions are a type of ground improvement that provide an improvement of a soil mass by insertion of a material with better characteristics than the surrounding soils. There are primarily two types of inclusions: “Soft” inclusions which are constructed of granular material (Stone Columns, Rammed Aggregate Piers, VibroPiers...), and “rigid” inclusions which are constructed of grout inserted with or without pressure (VibroConcrete Columns, Controlled Modulus Columns, Soil Mixing Columns).While the central principle of the inclusions is similar (i.e., overall improvement of characteristics of the soil mass below the structure), the load transfer mechanism is radically different for each technique. Therefore, the applicable design methodology is specific to the type of inclusions and there exists no universal method of design which spans across all inclusions.This paper will present an in-depth comparison between the standard design methods used for “soft” granular-type inclusions (Priebe modified, Balaam & Booker, Goughnour & Bayuk...) and the methods used for “rigid” inclusions which mainly rely on finite element analysis. The paper will explain why the design for soft inclusion methods cannot be applied to rigid inclusions and vice-versa. Each design method will be reviewed in detail to better emphasize its limitations and advantages.Two case histories will also be presented; one for each type of inclusions in order to illustrate the concepts developed in the first part of the paper.1 INTRODUCTION1.1 GENERAL OVERVIEW OF GROUND IMPROVEMENT WITH INCLUSIONSThe use of ground improvement methods to provide the appropriate amount of foundation support is a growing and constantly evolving industry. Traditional structural foundation methods including ‘shallow’ and ‘deep’ foundations do not adequately address the wide range of settlement tolerances, soil conditions, and loading considerations inherent to each unique potential project. In some instances, ‘shallow’ foundation solutions are simply not feasible due to soil and loading constraints. Furthermore, ‘deep’ foundation solutions are used to ‘bridge’ the soft compressible soils, ensuring that the entirety of the load in the structure is transmitted through individual elements into competent layers below the ground surface (bedrock, dense residual soils). Highly concentrated structural loads are transferred into the individual elements by means of direct contact requiring the use of structurally rigid surficial components (structural slabs, grade beams, and pile caps).Ground improvement bridges the gap between these two traditional methods, offering adequate foundation support while using more costeffective techniques and design methodologies. Inclusions are a type of ground improvement used to provide a reinforcement of the soil mass through the vertical insertion of a material with better characteristics than the surrounding soils. Much like deep foundations, inclusions are installed through soil layers with high compressibility and/or low bearing capacity and terminated in a suitable bearing stratum. However, unlike deep foundations, ground improvement inclusions rely on a distribution of load between the soil and the inclusions. By doing so, some of the structural load is applied directly to the soil in a proportion equal to its bearing capacity and compressibility limits, while the rest of the load is shed into the vertical inclusions down to the bearing stratum. Load sharing is a critical aspect in the performance and design of the various ground improvement methods."

Jan 1, 2015

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By K. Rainer Massarsch

The effects of soil displacement caused by pile driving on adjacent piles and structures are discussed. A method is proposed to estimate the point of force equilibrium which makes it possible to calculate up-lift forces and pile head movements. For the case of pre-coring a method is proposed to estimate the stability of the bore hole, based on cavity expansion theory. Model tests were performed to establish the displacement pattern of the soil during the driving of a pile group. It can be concluded that at the ground surface, already installed piles have little influence on the lateral displacements, but reduce significantly the soil heave. During the driving of a pile group, the soil is displaced according to a complicated pattern, which is strongly influenced by the order in which the piles are driven. In clay the displaced soil volume corresponds to the total volume of driven piles.

Jan 1, 1989

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By Hyu-Soung Shin

This study is concerned with the characteristics of the behavior of steel-concrete composite drilled shafts, a material that is used for large bridge foundations, and especially for weak submerged ground conditions. Depending on the loading or boundary conditions considered, the behavior of foundation will vary. The bearing capacity of steel-concrete composite drilled shaft is influenced by initiation and propagation of fractures along the interface between steel casing and filled concrete. The interface effect is taken into account with the following two simplified cases: (1) detached model with free interface (no shear stiffness of interface) between concrete core and steel casing, (2) confined model by an upper steel cap with free interface. In the confined model, it is intended to have an unified behavior of composite shaft between concrete core and steel casing but there is interface between them. Intensive numerical studies have been undertaken to investigate detailed behavior of the composite shaft. In this study, 3-D finite element analysis is employed. Ground conditions typical of those encountered for the design of drilled shaft under water are considered affecting the behavior. Also, an attempt is made to generate possible combinations of the loads which have been considered in fields. Detailed characteristics of the stress and displacement distributions are evaluated to understand the mechanisms of composite shafts.

Jan 1, 2007

By Brian Langdon

The DRIVEN GROUT PILE was developed in 1989 by DeWitt Construction, Incorporated. This piling essentially consists of a cost-in-place concrete piling that reacts on a steel boot that is driven to bearing. This report will describe the driven grout pile, its background and its installation. The advantages and disadvantages of this system are also discussed. Finally, the results of actual field installations are presented and discussed. BACKGROUND The DRIVEN GROUT PILE was developed out of a need for a low-cost high capacity piling (100 ton) that could be installed with ordinary pile driving equipment. This search was motivated by attempting to incorporate the material economy of an auger-cast piling with the "empirical load test" of a driven pile. Typically, the least cost material for piling in the 100 ton range is concrete (grout). A grout shaft with minimal reinforcement can withstand a compressive load of 100 tons for a material cost in the range of $6.00 to $8.00 per lineal foot. A pipe piling with a capacity of 100 tons has a unit material cost ranging to $13.00 per lineal foot. The marriage of these two advantages resulted in the DRIVEN GROUT PILE. A pile that utilizes the economy of a reinforced grout shaft and has the loading confidence of a driven pile.

Jan 1, 1990

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By W. H. Liu

The stability of floors of large drydocks and wagon tipper sheds at coal terminals is an important matter but quite difficult to solve. Anchors can be used to join floors to foundations thus ensuring the stability of floors by the self-weight of floors and the pull of anchors. In this paper, the author describes the structures and types of the anchors used in the floors of the drydock in Beihai Shipyard and the wagon tipper shed at Shijiu Port, both in Shandong Province China, the determination of bearing capacity of anchors in rock bed of highly weathered granite, the comparison between prestressed anchors and non-prestressed anchors, the construction technology of anchors and the analysis of field experimental data.

Jan 1, 2010

By Mahdi Soudkhah, Akhter Hossain

Vertical micropiles are generally considered to be low in lateral resistance. Therefore, battered micropiles are often used when additional lateral load carrying capacity is required. However, battering of micropiles can sometimes be restricted due to existing adjacent structures or utilities, especially in highly urbanized areas. For example, presented in this paper are lateral load test data from a 43-story building project in New York City where vertical micropiles were used due to proximity to adjacent structures. Three static lateral load tests were conducted on micropiles consisting of 13.375-in-outside diameter and 25- to 51-ft-long casings, and socketed 10 to 12.6 ft into the bedrock (gneissic schist). The subsurface profile above the bedrock consists of loose to very dense, mostly sandy and silty soils. The design load for the three test piles was 14,000 lb and the maximum load applied during the tests was 200% of the design load. Lateral load- displacement behavior of the free pile heads from the load tests are compared with the results of p-y analyses based on a widely used p-y method for sandy soils and using a lower and an upper bound estimates of soil index properties and strength parameters. Since the existing p-y curves were formulated for larger diameter driven piles at a specific geographic location, major differences are observed between the results of the load tests and the p-y analyses. In general, the lateral displacements estimated based on the p-y analyses using upper bound soil parameters are relatively closer to the results of the field load testing. Modified p-y curves specific to the sandy and silty soils representative of the general subsurface conditions of New York City matched with the lateral load tests are presented in this paper. INTRODUCTION Micropiles generally are limited in lateral load carrying capacities due to their relatively higher slenderness ratios (ratio of depth to diameter) compared to more conventional deep foundation alternatives, such as driven piles and drilled shafts. So, micropiles are not typically considered as deep foundation solutions when significantly high lateral loads are expected on the substructures. Various means to increase the lateral resistance of micropiles include battering and installing an oversized casing in the top portion of the piles (FHWA 2005; and Richard and Rothbauer 2004). However, it is often not possible to install micropiles in a battered position in highly urbanized areas due to existing adjacent structures or utilities. Installation of oversized casing is often restricted by limited space availability and concerns of losing lateral capacities due to closely spaced group of piles. Thus, estimation of lateral resistance of vertical micropiles can become highly important for geotechnical engineering projects in urban areas when a small to moderate amount of lateral resistances are expected from the substructures, often to withstand seismic and wind loads.

Jan 1, 2019

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

By Jean Wehbe, Daniel C. Brahana

"The new Mercedes-Benz Stadium (MBS), home of the Atlanta Falcons, is part of a new era of stadium construction in the U.S. These new-age stadiums are larger and have more amenities than their predecessors. Many of the MBS’s features, including its innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are supported by drilled piers. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 ft (1.8 m and 1.9 m). Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings were used to support the more lightly loaded portions of the structure.The focus of this article is the construction aspects of the drilled pier foundations. Initially, a fairly extensive drilled pier load test program was performed. Load testing included a Statnamic compression test, two Osterberg Cell tests and two lateral tests. Production pier installation included over 3,800 linear ft (1,158.2 m) of earth excavation and over 1,350 linear ft (411.4 m) of hard rock excavation. The piers contain more than 6,600 cu yd (4,587.3 cu m) of concrete and 1,100 tons (998 tonnes) of reinforcing steel. Drilled pier installation took about 4.5 months. ABE Enterprises was the specialty foundation subcontractor and Bauer-Pileco was the equipment provider.Site and Subsurface ConditionsThe project site is in downtown Atlanta and was originally occupied by residential buildings. A portion of the site was later developed as a rail yard, and other areas contained light manufacturing, warehouses and other relatively light structures. For the past 15 to 20 years the site had been used for surface parking.Beneath a surficial layer of manmade fill, soil test borings at the site generally encountered residual soil, partially weathered rock and the parent bedrock. The bedrock at the site is highly variable, both in elevation and in hardness/quality. The depth to rock is reasonably uniform within the western two-thirds of the site at about 20 to 50 ft (6 to 15.2 m), with a few exceptions. In the eastern third of the site, the rock drops off dramatically to the north and east. In one mega column cap, there was almost 80 ft (24.3 m) in elevation difference. In two borings in the cap that were 20 ft (6.1 m) apart, the top of rock varied in elevation by 34 ft (10.3 m)"

Jan 1, 2016

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

Jan 1, 2004

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021