Search Documents

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

By D. Goossens

Quality control is a system which should guarantee that quality is achieved. It is the execution and verification of a project in an organised way, in order to obtain the maximum of certainty that the results meet the requirements. This concerns all stages of the project, from the soil investigation, over the design, to the execution. Quality control can and has been successfully realised for important projects by means of a quality plan. A quality plan is based on a number of general considerations, but should certainly be focussed on the particularities of a specific project. Practical examples of quality plans, which have been realised on sites in Belgium, are developed and the advantage of the system is shown by concrete case studies.

Jan 1, 1996

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Franklin M. Grynkewicz

As part of the Boston Harbor clean up project, the new 1,000 mgd Deer Island Sewerage treatment plant includes ten 240 feet high egg-shaped "residuals" tanks. Contract documents called for these structures to be supported on 2,600 sixteen inch concrete filled pipe piles. The project site is underlain by highly variable glacial and marine deposits. Subsurface conditions vary from one extreme where firm glacial deposits exist at subgrade to the other extreme where 70 feet of medium stiff clays overlying weathered bedrock must be dealt with. The most common profile consisted of 15-20 feet of sands, 20-40 feet of marine clays, and 20-60 feet of stratified glacial deposits (commonly called tills) overlying Argillitic bedrock. Post bid redesign work, initiated as a cooperative effort between the owner and the general contractor, demonstrated that an $8 million savings could be realized if high capacity 48 inch diameter caissons replaced the specified pipe piles. A highly unusual arrangement of having the general contractor and specialty subcontractor providing input to the owner's engineering team allowed the redesign work to proceed on a "fast-track" schedule.

Jan 1, 1992

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Jan A. Nilsen

This paper describes a key element in the construction of a major project undertaken by Harbourfront Corporation in its efforts to rejuvenate the central Toronto waterfront. The Spadina Pier forms one of the two major structures of the $10 million marina complex. Completed in early 1986, the 150 metre(490 ft.) long by 43 metre(140 ft.) wide pier structure will contain a 320 car parking garage as well as providing the foundation of a 17-story residential tower and a two-story retail/commercial complex. However, the pier structure posed a considerable challenge to its developers due to the the many restrictions imposed on the site by the environmental authorities which ruled out the construction of dykes or the placing of other fill materials on the highly contaminated bottom sediments. In addition, access at the site was restricted by its proximity to the main harbour navigation channel and a grain elevator berth. The original design called for a cofferdam to form an integral part of the finished structure. However, the contractor chose to regard the cofferdam as a temporary structure and proposed to construct the pier in the dry by enclosing the 10,000 square metre(107,600 sf) site with a 450 metre(1480 ft.) long single wall steel sheet pile cofferdom 7.5 metres(25 ft.) from the final pier structure. This paper will describes the design and construction of the cofferdam. Prior to finalizing the pier design, a geotechnical investigation of the shale bedrock was undertaken as well as a small sheet pile test cell program to evaluate the feasibility of driving a Canadian manufactured cold-rolled sheet pile into the bedrock. Relying on the design parameters for the shale bedrock, Foundation designed the cofferdam utilizing a post-tensioned bipod bracing system to resist a 7 metre(23 ft.) hydrostatic head as well as the maximum wind and wave forces expected at the site. The bipod bracing system consists of diagonal H-pile raker piles and verticle pipe piles anchored to bedrock with post-tensioned anchors grouted into bedrock.

Jan 1, 1987

By Donald A. Bruce

Various types of contemporary Deep Mixing Method (DMM) techniques have been used in the United States since 1986. Such techniques owe their origins to Japanese and Scandinavian developments, which began almost three decades ago. The growing demands of urban infrastructure development and rehabilitation have created a very active and rapidly expanding market demand in the United States especially since the early 1990s, and there is a clear need for a new and fundamental review of the surprisingly large number of DMM techniques that are being used domestically, or are available in other parts of the world. Following a summary tracing the historical development of DMM, and a generic classification of applications, the paper provides a review of each of the many different proprietary methods, which the authors have identified during preparation of an international survey funded by the Federal Highway Administration (FHWA). Data are also provided on commercial aspects of the various DMM techniques worldwide.

Jan 1, 1998

By Alexi J. Neill

"This presentation will showcase two challenging projects with deep excavation support systems in the Atlanta area where state-of-the-art instrumentation and monitoring systems were used to manage risk by confirming design performance requirements / calculations during construction. The instrumentation and monitoring system successfully reduced risk by recording real-time data on a project website while simultaneously sending email alarms to key site personnel when data exceeded pre-determined alarm thresholds. The monitoring data revealed unexpected performance at an early enough stage so that contingency plans could be engaged and remedial efforts devised in order to limit the consequences. Finite element analysis was used to model deformations, analyze the unexpected performance, and prepare theremedial design.INTRODUCTIONConstruction in densely populated urban areas is becoming more common in order to keep up with the increasing infrastructure demands of our growing population. America’s big cities continue to outpace the overall nation in population growth. The city of Atlanta, the nation’s ninth largest city based on metropolitan population, is a prime example of this. The population has grown at a rate of 6.6% between 2010 and 2013, nearly triple the overall growth rate of the United States during the same period (SustainAtlanta, 2015).As a result of increasing infrastructure demands in Atlanta, developers are now constructing larger buildings on smaller properties. In addition, developers are attempting to maximize space on their selected properties, often by designing underground parking garages to accommodate as many cars as possible on these compact sites. In some cases the selected sites are adjacent to buildings, utilities, and other existing structures. The risk associated with construction increases during underground work that requires a support of excavation system, particularly on confined sites adjacent to existing structures. There is a risk posed to people, property, and the environment that the project team should monitor when constructing in these conditions."

Jan 1, 2016

By Scott D. Neely, Donald R. Clark

"An existing landslide located at the southeast corner of the Telluride Regional Airport has been in an active state of failure for several years. The presence of the landslide has represented an on-going liability for the Airport, the Federal Aviation Administration and the Colorado Department of Transportation. A catastrophic failure of this landslide occurring in a manner similar to that which occurred at the Airport in 1987 has posed an on-going threat to closing Colorado State Highway 145 south and below the slide area. The existing landslide has been characterized as a series of multiple failed block areas located downhill of the airport runway that have occurred in severely weathered Mancos Shale.A total of 12 alternatives were evaluated to mitigate the landslide, including the preferred alternatives of either partial or total landslide removal. However, prior development has left essentially no place on the airport property that would allow for the disposal of the landslide debris for either the total or partial removal alternatives, and the closest off-site disposal area was approximately 40 miles from the site. As a result, in-situ stabilization of the landslide, including a primary system of isolated tie-back anchor plates with strand anchors, and a secondary system of high strength steel mesh and intermediate anchors was selected for the ultimate design of the project to stabilize the landslide in place.For design purposes, geotechnical characterization of the slide area was accomplished through geological mapping, conventional borehole exploration and geophysics using multiple electrical resistivity. The paper discusses the design process utilized and the unique challenges faced one-third of the way through construction when discovery of a survey error required redesign of the entire landslide mass stabilization system using the prefabricated anchors that had already been delivered to the project.INTRODUCTIONTelluride Colorado is located at the toe of the Colorado Rocky Mountains on the western slope. The Telluride Regional Airport is located on Deep Creek Mesa about 5 miles west of the town of Telluride.The landslide is located at the southeast corner of the airport just below an abandoned portion of the quarry access road on a south facing slope. The quarry access road is located below the elevation of the runway and outside the elk fence that surrounds the air traffic area of the airport property. Since the reconstruction of the runway, the access road to the quarry and the construction access road for the reconstruction of the airport runway and safety area were rerouted to stable ground north of the previous access road location and off of the head scarp of the landslide."

Jan 1, 2015

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Nicolas Denies, Gust Van Lysebetten, Bart Lameire, Jan Maertens, André Vervoort, Noël Huybrechts, Flor De Cock

"Abstract Originally developed for ground improvement works, the deep mixing method (DMM) has increasingly been applied in recent years for the realization of soil and water retaining structures and as alternative to traditional foundation solutions. From practice, there is a real need for practical guidelines dealing with the execution, the design and the control of such applications. With the aim of developing such guidelines, the BBRI ‘Soil Mix’ project was initiated in 2009. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites has been tested. In spite of the large advances in the mechanical characterization of the DSM material, one major issue remains the representativeness of the typical core samples in comparison with the real scale behavior of the soil mix elements. There is among others the question of the influence of the unmixed soft soil inclusions on this behavior and the issue of the scale effect which must be considered in the design. In order to investigate these questions, 8 large scale UCS tests and 17 large scale bending tests have been performed on excavated soil mix elements. The present paper discusses results of this experimental campaign, presents some research perspectives and highlights different aspects related to the design of soil mix elements for the realization of retaining wall or foundation solution.INTRODUCTIONSince several decennia, the deep mixing method (DMM) has been used to improve the strength and deformation characteristics of weak soils. In recent years, deep mixing has increasingly been applied – in Belgium and in other countries – for the realization of soil and water retaining structures and alternative foundation concepts. With regard to the execution of the DMM, one can refer to the European standard EN 14679 on deep mixing (2005) that was elaborated under the umbrella of CEN TC 288 “Execution of special geotechnical works”. However, from practice, it has been experienced that this execution standard does not provide enough pragmatic information and guidelines, in particular for the more recent applications of the deep mixing method (with retaining and bearing functions). The same need by the sector for guidance rules linked to design aspects in the context of Eurocode 7 was experienced as well. With the aim of developing such guidelines and in order to provide feedback to the European standardization platforms, the Belgian Building Research Institute (BBRI) has initiated the BBRI ‘Soil Mix’ project (2009-2013) in collaboration with the KU Leuven and the Belgian Association of Foundation Contractors (ABEF), the Belgian branch of the EFFC. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites, with various soil conditions and for different execution processes (CVR C-mix®, TSM and CSM), has been tested (Denies et al., 2012)."

Jan 1, 2014

By Armin W. Stuedlein, Steven R. Saye

The differences between calculated axial pile capacity and the capacity realized during and following installation has long presented a significant concern for foundation engineers and contractors. Such differences have increased in prevalence with the increased use of larger diameter steel pipe piles and the significant increase in design-build contracting. The writers present concepts to close the gap between calculated axial pile capacity and the capacity realized during and following installation of driven pile foundations, including: (1) pile set-up in plastic soils, (2) limitation of re-driving of piles after setup which serves to reduce pile capacity, (3) the use of a vibratory hammer to install piles in cohesive soils disturbs the supporting soils and reduces the pile side resistance capacity significantly, and (4) long pile installation times for open-ended piles can damage the pile side resistance. Examples are presented from practice to illustrate these concepts and to guide pile installation planning to recognize the installation impacts and either consider alternate installation approaches or to properly consider the installation impacts during design.

"The development of non-destructive testing (NDT) methods for deep foundations occurred in several parts of the world, gradually coming together into the present state of the art. The compilation of this brief NDT history is the best effort of several knowledgeable members of the Deep Foundations Institute (DFI) Drilled Shaft Committee, coupled with the recollections of several historically important contributors to the science. It is not intended to be exhaustive, but rather concentrates on the origins of the methods in common use and on which this manual focuses.Modern NDT methods, and the spread of knowledge about them, have expanded through application to real foundations projects by the original researchers, sometimes inspired by their own curiosity, sometimes to respond to the cost and time limitations imposed by static testing, and sometimes to address the questions raised on research projects funded by large government agencies such as the Federal Highway Administration (FHWA) in the USA, and various European transportation agencies. Initial attempts were primitive by today’s standards, and equipment limitations often restricted successful application to relatively simple cases. As electronics improved and confidence in them increased, the early researchers began commercial promotion of their methods, published their findings in professional journals, and shared experiences at conferences held by such groups as the DFI, the International Association of Foundation Drilling (ADSC), the International Conferences on the Application of Stress-Wave Theory to Piles and other venues such as ASCE and Transportation Research Board (TRB) conferences.NDT methods were developed to fill a need to assess the quality assurance of deep foundation elements. New pile types and higher design loads prompted engineers to verify the safety of their foundations via additional testing during construction. Static load testing was the traditional method to assess performance, and this method has been used for centuries and perhaps even millennia.Relatively recent alternatives to static load testing for determining the capacity of drilled shafts include the bottom load test method. This method uses a jack embedded in the lower portion of the pile (bottom load test) and was first reported to be used from Canada in the early 1970’s (Gibson& Devenny 1973). The concept immediately caught on in Israel, where it was used as a quality control measure for small-diameter piles drilled in rock (then a new technology). The method was later patented in the US by Jorj Osterberg, and offered as a commercially available service in thelate 1980s (Osterberg, 1989)"

Jan 1, 2004

By Brian E. Ladd

"A load test program was performed on two auger cast piles constructed in the Inner Coastal Plain geology of North Carolina. Both test piles were installed through Coastal Plain deposits and into underlying Piedmont residual soils; one test pile was embedded into partially weathered rock (PWR). The recommended 100-ton design load was confirmed by a test program that included instrumenting the piles with strain gages. The two piles performed differently during the load tests due to the effect of embedment into PWR. Loading Test Pile No. 1, which was not embedded into PWR, to failure at about 230% of the design compressive load allowed for evaluation of the mobilization of the ultimate shaft and end bearing resistances. Mobilization pile resistance was evaluated by comparing shaft and end bearing resistances to top of pile deflection (d) normalized by the pile diameter (D). For Test Pile No. 1, the ultimate average shaft resistance was achieved at d /D of about 7.5% and ultimate end bearing resistance at d /D of about 9.5%. Test Pile No. 2, embedded into PWR, achieved a d /D of only about 4% at 200% of the design load and was not loaded to failure. Shaft resistance was mobilized at a different rate within each individual geologic layer, i.e. ultimate shaft resistance did not occur simultaneously for all geologic layers. As the available total shaft resistance was exceeded and end bearing mobilized, the unit shaft resistances reduced from the peak values. A modified Davisson offset using d /D of about 6.5% appears applicable for evaluating the ultimate capacity of auger cast piles in the Inner Coastal Plain.INTRODUCTIONAuger-cast-in-place (ACIP) piling was developed in the 1940’s and patented in 1956 (Neely, 1991). Since patent expiration in 1973, ACIP piles are abundantly used in the United States, particularly in the southeast. However, most literature addresses driven piles constructed in sand and clay with lesser discussion of drilled piles. Conventional design methodologies (a- method, ß-method, SPT or CPT correlations, etc.) are based on data derived from numerous projects in a great variety of geologies. O’Neil (2001) notes that there are significant levels of uncertainty in the “universal” databases as evidenced by coefficients of variation of 0.35 to 0.40 for geotechnical parameters (su, SPT-Nvalue, etc.) used to estimate pile capacities.There is a need to develop local databases developed from data obtained from load tests that measure shaft resistance and end bearing. This paper presents the results of load tests conducted on axially loaded auger-cast-in-place piles constructed in the Inner Coastal Plain geology of North Carolina. Shaft resistance, end bearing, and movements that initiated mobilization of these resistances are described. The information presented herein can be used to refine geotechnical correlations and parameters applied in auger cast pile design methodologies."

Jan 1, 2017

By Bengt H. Fellenius

The design of pile foundations is much more commonly verified by means of a full-scale test, than is the design of other foundation units. The reason is not that our knowledge of pile behavior is more uncertain than our knowledge of other foundation types making the verification necessary, but more that the loads in a structure are more concentrated to single foundations in a structure founded on piles as opposed to structures on footings or mats. Therefore, should a pile cap fail or move, the adverse consequence of this is often drastic, as the piled structure has little freedom to transfer its need for support to other foundation units. Consequently, it becomes important to assure the design of piled foundations. In many, maybe in most instances, the static pile loading test is routine and geared toward determining an at least capacity, only. However, in these times there is an ever increasing liability of the professional, demands for increased economy of the foundation, and frequent lack of the involvement in the test of the experienced old-timer exercising good judgment. Furthermore, modern pile design is leaving the single, simple concept of capacity and requires more information from the test to assist in determining aspects of long-term behavior and settlement. Therefore, even the straight forward, routine static loading test requires improved planning, execution, and analysis.

Jan 1, 1990

By M. Zanotto

[ ] A period of heavy rains caused the river Adda to flood parts of the Valtellina, one of the Alpine valleys of Northern Italy. The exceptionally high waters put under considerable strain the whole system of embankments and levees controlling the river and protecting the adjacent towns and lands. In some places the water breached and washed away the embankments, submerging large tracts of cultivated land, buildings, roads and railway tracks. The town of Talamona, in the lower Valtellina, was hit particularly hard: in its proximity the river overrun and then washed away 300 m (1,000 ft) of embankment (see vicinity map, fig. 2), depositing large amounts of riverbed debris onto over 400 hectares (1,000 acres) of fertile land.

Jan 1, 1992

By Robert E. Schock, Eric J. Risberg

"Less than 20,000 years ago, the last of the glaciers retreated from the Chicago region. They left behind sheets of glacial clay till underlain by dense, over-consolidated till (“hardpan”) below which is the limestone bedrock, found about 100 ft (30.5 m) below street level. The most notable feature in this profile is the unusually soft clay till that has historically been called “Chicago Blue Clay.”But the founding fathers of Chicago really didn’t care about what was under the ground. They recognized the importance of the city’s location as a potential trade and transportation hub. With access to the East through the Great Lakes and access to the West through the Mississippi River system, the viability of the city was evident. Chicago’s population grew rapidly. The city continued to grow through the Civil War years, but was dealt a devastating blow in 1871 by the Great Chicago Fire, leaving the city in ruins. The Birth of the SkyscraperAfter the cleanup of the Great Fire came the first real building boom in Chicago’s history. During this era, buildings were generally founded on shallow footings bearing on sand or clay. Many multistory buildings were constructed between 1880 and 1890 on spread footings. The first tall buildings were constructed with load bearing masonry walls. These early tall buildings suffered significant settlement as the soft clay underwent consolidation.The Home Insurance Building, built in 1885, was 12-stories tall and is generally acknowledged to be the first “skyscraper” in the U.S. It was the first building constructed with an iron skeleton frame instead of load bearing masonry walls. Spread footings were used under the interior columns in an effort to better distribute the loads, but the building still experienced large settlements.Construction began for the Monadnock Building in 1891. The 17-story building was built using load bearing walls 7 ft (2.1 m) thick, supported on rail-grillage footing foundations. When completed in 1893, the Monadnock Building boasted the title “World’s Largest Office Building.” The total building settlement over the past 125 years has been measured at over 20 in (0.51 m). The engineering community in the late 19th century observed settlement, but did not yet understand the process of consolidation of the soft clay beneath the city. During this time, many of the new buildings required structural repairs during and after construction; the problem was especially acute in buildings where highrise towers joined lower podium structures."

Jan 1, 2016

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022