Search Documents

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By David G. Winter

The Olive 8 excavation site in Seattle was surrounded on three sides by conditions requiring innovation, careful modeling, and extensive instrumentation to support use of a first-of-its-kind shoring system. The solution combined heavy soldier piles, long and steeply angled tieback anchors, and tightly spaced soil nails to support surcharge loads from a 33-story adjacent tower separated by a narrow alley housing critical utility lines. Land restrictions on two other sides of the site also required innovative applications of traditional methods. The Olive 8 project has won three state and local awards for innovation and has been reported on in Engineering News-Record and has been the subject of two feature articles in the Seattle Daily Journal of Commerce. This paper presents the conditions and site challenges, reviews the design analysis, discusses the shoring performance, and looks at other potential applications.

Jan 1, 2009

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

By Jerry F. Parola

In current practice, pile foundation design is based on a general under-standing of pile-soil interaction during installation and superstructure-pile-soil interaction after construction. The pile design is a reflection of experience, precedent and judgment for normal piling practice of working load capacities up to approximately 100 tons with corresponding ultimate capacities up to 200 tons. For higher capacity piles, pile design is even less predictable. In particular, the feasibility of pile installation is an important design consideration that must be given the proper attention. An installation capability that is not given the required emphasis can cause unnecessary problems.

Jan 1, 1986

By Wolfgang G. Brunner

A 3800 m long temporary water-retaining dike has been constructed under extreme conditions in the harsh northern climate to enable two of the kimberiite pipes at the Diavik Diamond Project reserve to be mined using open pits. The Diavik Diamond Project is located on East Island at Lac de Gras in Canada's Northwest Territories, approximately 200 kilometres south of the Arctic Circle. The dike which has been constructed in up to 25 m deep water from crushed granite quarried from the site projects into Lac de Gras encircles the first two of the kimberiite pipes to be mined. An 800 mm wide diaphragm cut­off wall constructed of bentonite, cement and crushed rock, totalling 33,000 m2, and a two-phase jet grouted curtain wail at its base, totalling 8,400 m2, have been installed through the dike and underlying till foundation into bedrock. The cut-off is designed to minimise water seepage from Lac de Gras through the dike. In order to ensure that the dike had adequate internal stability and diaphragm wall construction could proceed safely, the crushed rock fill material dumped into the lake was first compacted by TR 75 deep vibrators. In 2000, Bauer Maschinen GmbH of Schrobenhausen, Germany were awarded the contract for the supply of all specialist foundation equipment required on site and for providing technical support to the Canadian main contractor Lac-de-Gras-Construction throughout the construction of the cut-off walls during 2001 and 2002. Installation of the cut-off walls was completed in July 2002, three weeks ahead of schedule, and dewatering of the inner dike areas commenced just 5 days later and has continued throughout August and September. After completion of extensive testing of the diamond recovery plant, the mine is scheduled to go into full open pit production in February 2003.

Jan 1, 2003

By Vijayakumar Viramuthu, Martin Heinrich

Tower of Lot L, L1 & M, Kuala Lumpur City Centre when completed would stand 700 m tall. This Mega tall Skyscraper would merely be less than 500 m away from the world tallest Twin Tower, the Petronas Twin Tower. From June 2018 to February 2020 BAUER (MALAYSIA) SDN. BHD. constructed 225 nos bored piles with diameters of 2.0 m and 2.5 m for this tower. To comply with the depth requirement of the initial design and the need to have the pile toe 2.0 m above competent bedrock, the drilling equipment was required to be able to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to controlling the open borehole stability over time with polymer, installing 70 t heavy steel cages and pouring up to 550 m³ concrete continuously in conjunction with installation of 88 t heavy kingposts into workable fresh concrete. The piling works were executed with one BAUER BG 48 and one BG 72, the biggest drilling rig globally available.

May 1, 2022

By Lu Peiyan

A computation model of soil-pile (wall) interaction under lateral loading is presented in this paper. The model has been applied to some engineering projects, and the comparison between computation result and measured result shows good agreement, so the model is proved to be correct and practical.

Jan 1, 1991

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Allan Sylvester

This paper will discuss the design, construction, and performance of the support of excavation on the San Diego State University LRT Station. The vertical elements of the system include drilled secant piles and drilled soldier piles. We will discuss the geo-technical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the pile and support of excavation systems. In consideration of the conference theme, there will be a discussion of the successful accomplishment of meeting the interim milestone dates of the Contract. The project team cooperatively worked to design and install approximately 1,100 drilled secant and soldier piles as well as excavate and install the balance of the support of excavation elements in such a manner as to minimize the disruption to campus students and operations.

Jan 1, 2002

By Jay A. Berger

Nondestructive testing of deep foundations for integrity problems made great strides in the late 1980's. Inexpensive portable computers have allowed the immediate and rapid processing of field measured acceleration records which can provide insight into the relative structural integrity of a previously installed foundation member. Although the gathering, processing and displaying of the data is now straightforward, interpretation remains at times rather challenging. This paper provides a brief introduction into the theoretical basis for data interpretation and the hardware necessary for data acquisition. Five case studies are discussed which demonstrate the varied applications of low strain integrity testing of deep foundations and the efficiency at which they are completed. BACKGROUND One dimensional wave mechanics, when applied to a linear elastic pile with a length that is an order of magnitude greater than its width, provides a straightforward basis for the interpretation of motion measurements made at a pile top. When impacted, a stress wave travels through the pile at a wave speed, c, which is a function of the elastic modulus, E, and mass density p (i.e., E=pc2). The applied load F, and particle velocity v, at a point are related by the equation F=Zv. For a cross-sectional area A, the proportionality constant Z is equal to EA/c. Because Z is a measure of the pile's resistance to change in velocity it is called the pile impedance.

Jan 1, 1990

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By Peter Florian

At 5:50 am on October 1, 1992, the new $800 million Pittsburgh International Airport Midfield Terminal opened its gates to the world after five years of construction and more than 24 years of planning. Despite numerous design changes, this massive project was completed on time and substantially within budget. The importance of this airport to Allegheny County and the Pittsburgh region was recognized 24 years earlier by Allegheny County Commissioners Tom Foerster and the late Leonard Staisey. Staisey and Foerster established a program to acquire land for the "Airport of the Future".

Jan 1, 1993

By William Van Impe

A most renewing and promissing soil displacement screw pile is called the O-pile. The O-screw pile is a soil displacement auger pile based on a screwing in - screwing out procedure. The displacement auger head consists of a discontinuously diameter - increasing steel tip, on top of which the continuous screw flange with variable pitch is mounted. The soil displacement is kinematically ensured by downwardly oriented slots mounted on the auger head at different well chosen locations on the flanges. This leads to a very efficient lower energy screwing-in sequence of the pile and consequently to a high penetration rate. A test loading program of instrumented O-piles has been carried out in order to evaluate the load settlement behaviour, the shaft and tip capacity of the O-pile, including its specific installation parameters.

Jan 1, 1996

By Dennis J. Riley

A. This outline addresses what a sub-contractor, or a subsub-contractor should do to get paid in the event the general contractor or building owner files for bankruptcy. B. Negotiating payment terms. Progress payments vs. "pay when paid". How a sub or subsub can avoid financing the contract. C. Court interpretation of "pay when paid" clauses allow postponement not excusal of payment. See, e.g., Seal Tite Corporation v. Ehret. Inc., 589 F. Supp. 701 (D.N.J. 1984) (where the court held that the general contractor could not delay payment indefinitely to the subcontractor in the event of non-payment from the owner); United Plate Glass Co. v. Metal Industries. Inc., 525 A.2d 468 (Commw. Ct. Pa. 1987) (where the court held that payment from owner was not a condition precedent to paying subcontractor but instead a timing mechanism indicating when payment should be made); But see. Straham v. Landis Construction Co., 499 So. 2d 417 (La. App. 4 Cir. 1986) (where the court strictly interpreted the "pay when paid" clause).

Jan 1, 1991

By Dennis W. Boehm

The building boom of the late 1970's and early 1980's has all but used up most of the better sites across the more populated metropolitan areas of the United States. This means that current buildings and other types of structures are being founded on more marginal sites. The use of marginal sites has placed ever-increasing quality control on the installation of the deep foundation systems utilized for these sites. Several remedial techniques are available for the repair of the deep foundation systems. These include minipiles, compaction grouting and jet grouting. Eight case histories are cited where these methods have been utilized to repair deep foundations.

Jan 1, 1999

The process of pile driving disturbs the soil around the pile. The nature and magnitude of disturbance depends upon 1) the pile size, and 2) the nature of soil. Therefore, the prediction of a single pile behavior based on soil properties of undisturbed soil samples may not match its performance. Under lateral loads, the pile may loose contact with the soil near the ground surface especially in clays. The soil pile interactions are influenced the most by pile behavior in this zone. This situation further affects the tally of prediction and performance. Piles are used in groups. The zones of overlapping stress from one pile to the other both around the pile and below their tip particularly in soft soils, contribute to group effects. Empirical solutions have been developed for prediction of the pile group behavior. The group action is more involved under vibrations. Several cases of single piles and pile groups under static and dynamic loads from published records have been analysed. It has been shown that single pile test is the best source of information on the soil-pile-soil interaction effects.

Jan 1, 1989

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Seth L. Pearlman

A major excavation support case history for the Eastern approach to the Third Harbor Tunnel (THT) in Boston, MA is described, which uses an anchored Soil Mixed Wall (SMW). Both general and project specific information is provided regarding the design and construction of SMW walls. In addition, conclusions are presented that discuss the suitability of this particular application and other possible variations.

Jan 1, 1993

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2004

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010