Search Documents

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By Padmavathi V, M. Najamuddin, M. R. Madhav

Granular piles are one of the leading ground improvement techniques, adopted for the betterment of bearing capacity and reduction in settlements of the foundations and also to accelerate consolidation of the surrounding soil. In the recent past, there has been extensive research on the settlement analysis and behavior of granular piles under varied soil conditions. The application of these theoretical solutions to practical problems requires a knowledge of representative values of the deformation parameters of the ground and the granular piles. However, very little information is available on these parameters. The paper presents a new method for the estimation of the modular ratio of granular piles and modulus of deformation of the surrounding in-situ soil from the compression load tests. The load - settlement response obtained from the compression test results are used in the back analysis for estimating the modulus of deformation of the ground. The presence of granular bed, under the rigid plate for load testing, has been given due consideration in quantifying the proportion of load transferred on to the stone column. Based on these considerations a new method is developed to estimate the modulus of deformation of the ground and the modular ratio of the granular pile.

Sep 1, 2022

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990

By Philip J. Daynes

As part of the regeneration of the centre of Dublin, a multi-functional development is being constructed on the site of the historic Smithfield Fruit Market. The site is being developed in three phases, and includes one of the deepest basements (10m) constructed in Ireland to date. Until the recent improved economic climate, there has been little requirement for deep basements in Dublin, and this is the first to be constructed entirely within fluvio-glacial gravels and boulders. The difficult ground conditions led to the adoption of a diaphragm wall solution to ensure a watertight construction. Tie-back anchorages are utilised in the temporary case, and the wall is propped by floor slabs in the permanent case. Where required by high bedrock levels, the diaphragm wall is dowelled into limestone bedrock to ensure toe stability. The recorded lateral movement of the wall is significantly below that calculated by numerical analysis. Temporary bentonite cut-off walls were installed to divide the site into discrete sections. The basement was constructed as a tanked structure, and is subject to uplift water pressure. Passive tension minipiles provides an innovative alternative to the standard stressed anchorage solution. This paper describes:- design and construction aspects of the diaphragm wall, tie-back anchorages, and anti-flotation minipiles, together with recorded lateral wall movements,

Jan 1, 2003

By Madan B. Karkee

The understanding and the development of sound theoretical basis concerning the pile foundations has been phenomenal during the past few decades, considering the thousands of years the piles have evidently been in use. The importance of the quality assurance and the need for verification of load bearing capacity is being further reinforced rather than undermined by these developments. This is evidenced by significant developments made in the pile load test technology in recent decades, making it possible to make judicious selection of a test method, or a package of test methods, suitable for a given situation. The selection depends on the objective of carrying out the test and the reliability desired. Presently, the possible selection ranges from dynamic to static methods. The extent of dynamic effect in a test can be reckoned based on a dimensionless parameter defined as the 'relative duration'. Examples of different load tests are given for illustration of the different methods currently in use.

Jan 1, 1997

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

By Alan J. Lutenegger

Some years ago, a method was developed to incorporate a grout column around square-shaft helical screw-piles and anchors to increase shaft buckling resistance under compression loading. An additional benefit of this grouted shaft is to increase the load capacity in both compression and tension, depending on the geometry of the lead helical section and the soil conditions. Because of the unique construction procedure, the contribution of the shaft to the total capacity has largely been unknown. The behavior of grouted shaft helical anchors in clay was investigated by performing full-scale axial uplift (tension) load tests on a series of anchors installed at the University of Massachusetts Geotechnical Test Site. In order to isolate the contribution of the grouted shaft to the total load capacity, anchors were installed with a wooden dowel connection between the lead helical section and extension sections on three of the four anchors so that only the shaft resistance would be measured during the load tests. The grouted shafts ranged in length from 10 to 30 ft (3 to 9 m). Initial tests were performed approximately 5½ months after installation. Nearly four years after the initial tests were performed, the tests were repeated to evaluate any significant change in capacity with time and/or repeat testing (preshearing). The soil conditions at the site are presented along with the load-displacement curves for both the initial and repeat teats and a discussion of the analysis of the results. Repeat load tests showed an increase in capacity from the initial testing, however the percent increase was not the same for all depths. The results demonstrate that considerable shaft resistance can be developed in clays from the grouted shafts as might be expected. Depending on the L/D ratio of the shaft and the contribution of the lead helical section, at working loads the shaft capacity can dominate the behavior.

Jan 1, 2011

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By Mark H. Balfe

Over the last decade, Fenway Park has undergone annual improvements to modernize the facility for players and fans. These renovations include the Monster Seats, the Right Field Roof expansion, a new pavilion behind home plate, expansion of the Red Sox clubhouse, additional roof seating, and concourse improvements. Retrofitting the historic ballpark to bring it up to current standards required installation of foundations to support the new structural loads for each of the alteration projects. This required evaluation of existing conditions, and in many cases augmentation of the foundations at existing columns to accommodate the structural changes to the park. New foundations, generally consisting of drilled-in micropiles, were installed in numerous configurations and conditions. Since 2003, a total of 215 drilled-in micropiles have been installed to augment various columns around the park. The micropiles range in capacity between 40 and 70 tons and are installed through Fill and Organic Soils and embedded into the dense Glaciofluvial Sand and Gravel layer. Issues and learning related to the foundation augmentation include schedule constraints (work is typically conducted during the off-season and schedule is very aggressive), encountering old/abandoned utilities or foundations, ventilation of equipment, and management of spoils during micropile installation.

Jan 1, 2011

By Randy R. Huberty

Although originally designed with deep foundations consisting of all driven steel H piles and drilled caissons, a unique application of Augered Cast-in-Place (ACIP) piles as an alternate design resulted in a significant cost savings for the Midfield Terminal Project at the Pittsburgh International Airport. The project was enormous in scope covering an area two miles long by one mile wide, with changes in elevation of over 200 ft. The varying geology combined with the large amounts of fill required resulted in a complex set of geotechnical design parameters that had to be evaluated through both load testing and analyses. A total of almost 400,000 lineal feet of ACIP piles were installed for this project.

Jan 1, 2001

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

Jan 1, 2000

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By William J. Neely

Augercast piles are formed by drilling a continuous-flight auger into the ground and, on reaching the required depth, sand-cement grout or concrete is pumped down the hollow stem as the auger is withdrawn. The sides of the hole are supported at all times by the soil-filled auger, eliminating the need for temporary casing or bentonite slurry. The augercast piling method is fast and economical; there is no vibration, very little noise and, if executed properly, no ground displacements during installation. The method is well suited to sands which are easy to drill and are readily transported up the auger. Relatively little attention has been given to augercast piles in the literature which might be part of the reason for the considerable variations in local practice, building code requirements and design methods. The purpose of this paper is to discuss some of the features of augercast pile installation that are known to influence both the structural and geotechnical capacity of the pile, to evaluate several empirical design methods and to look at some important aspects of quality control of augercast pile installation.

Jan 1, 1990

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By Thomas M. Gurtowski

The New Pacific Northwest Baseball Park, now known as Safeco Field, is located directly south of the Kingdome in Seattle, Washington, and will be the new home of the Seattle Mariners baseball team. The location of the ball field is shown on Figure 1, Vicinity Map. The seating capacity is 45,600, and outfield distances are 331 feet in left, 405 feet in center, and 326 feet in right field. The overall dimensions of the stadium are 680 by 800 feet. It is bordered on the east by the Burlington Northern Santa Fe Railroad main line. A unique aspect of this ballpark is the retractable roof with a north-south span length of 660 feet. The roof consists of three separate sections that roll on elevated rails running east-west on the north and south sides of the stadium. The soil conditions consisted of near-surface fill underlain with alluvial and Estuarine deposits to depths of 60 to 80 feet. The bearing soils consisted of very dense, glacially overridden deposits. Groundwater is 4 to 7 feet below the ground surface, and the alluvial deposits are subject to liquefaction during a strong motion earthquake.

Jan 1, 1998