Search Documents

By James M. Tantalla, Jr. Ellman

"Construction of the powerhouse for the Willow Island Hydroelectric Project, located at the Willow Island Lock and Dam, required a 120-ft deep temporary excavation inside the limits of a cellular cofferdam on the Ohio River side of the excavation and a soil-bentonite seepage cut-off wall on the landward side of the excavation. Stability analyses were performed for critical sections to evaluate the stability of the soil slopes and rock cuts using limit equilibrium, tension crack, and buckling analysis techniques. The stability analyses indicated adequate factors of safety through the landside embankment sections, and for the weighting berm soil slopes in front of the riverside cellular cofferdam. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated marginal factors of safety for the 100-year flood condition. Consequently, the riverside portion of the excavation required enhanced stability measures, namely the installation of long, high-capacity rock anchors. Also, the dewatering system was modified to lower the site piezometric head to near the top of rock to improve the stability of the rock cuts.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. The rock anchors consisted of multiple, seven-wire strands designed to provide the full-required design load at 60% of the strand capacity. Rock anchor loads varied from 1,968 to 2,074 kips. The maximum number of strands per anchor was 59. Bond lengths assumed an allowable bond stress of 100 psi based on the rock bond from pull-out tests.Project DescriptionAmerican Municipal Power, a nonprofit organization that owns and operates electric generation facilities for its member communities, has been in the process of constructing hydroelectric power plants adjacent to existing navigation locks and dams along the Ohio River. The Willow Island Hydroelectric Plant was recently completed on the West Virginia bank of the river adjacent to the US Army Corp of Engineers (USACE) Willow Island Lock and Dam. The plant is on the opposite river bank to the locks, and includes two turbine generating units with FERC rated capacity of 44MW at a 20-foot head differential. The Ruhlin Company of Sharon Center, Ohio was awarded contracts to construct both the cofferdam and the powerhouse. Construction began in mid-2011, and was completed in early 2016."

Jan 1, 2016

By Konstantin G. Ashkinadze

The paper considers performance of piles supporting transient pipe anchors in heavy industrial pipelines. Events such as pump trips or opening and closing of large valves produce short-term dynamic pulses in the pipeline with variable spectral characteristics. Their magnitude is large enough to cause major damage to the pipeline and its anchors, which face horizontal impact loads amounting to hundreds of kN. Design of pile foundations supporting these anchors is often governed by limitation of deflection of the support to prevent overstressing pipeline connections and equipment nozzles. The maximum deflection does not always correspond to the largest load because the stiffness of the soil surrounding the piles heavily depends on the rate of loading. Faster actions encounter stiffer soil response while loads of smaller magnitude applied slowly may be more critical for the deflection time history of the anchor. A typical transient action has both high- and low-frequency harmonics, which makes the response complex. Using load rate-dependent p-y curves published in literature, the paper develops methods of analysis of pile foundations for transient anchors. Pile displacement amplitude – input frequency – natural frequency correlations and time histories of pile response are constructed for typical profiles of transient actions, considering nonlinear soil response to large horizontal loads.

Jan 1, 2016

By Luca Pingue, Regine Jagow-Klaff, Franco Muratore, Carlandrea Albonico, Damiano Frontini, Rudolf Wernecké

This paper describes an artificial ground freezing (AGF) application carried out to ensure both watertightness and structural support for the safe excavation of four cross passages of the Forrestfield Airport Link (FAL) project in Perth. The line will deliver 8.5 km extension of the existing urban rail network connecting the growing eastern suburbs of Perth with the existing suburban rail network. The proposed soil improvement technique is adopted as a smart alternative to jet grouting from the surface since the use of heavy equipment with long vertical mast was not allowed due to the line underpassing an airport in operation. In this paper, details of the challenges and lessons learned during both design and construction phases are given. Furthermore, it is described the geometry and the installation of freeze pipes in presence of a massive steel frame, ventilation system and slurry pipes of the tunnel boring machine (TBM) in operation. It is also illustrated the web monitoring system to allow key personnel to follow in real time the development of soil temperatures, tunnel convergences and ground surface deformations as well as changes in the interaction between international parties involved due to the COVID-19 pandemic.

May 1, 2022

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019

By Stefan Mewes

Europe’s second-largest seaport has installed a new combi wall consisting of pipe piles, sheet piles and inclined shaft grouted piles to support it. The new Liebherr piling rig with swinging leader was used to drive shaft grouted piles into a very dense soil layer of sand with glauconite. The 60 m Liebherr swinging leader was suspended at an inclination of 45° via a suspension frame and suspension ropes from the crawler crane. This inclined installation of shaft grouted piles via freely hanging swinging leader, as used for this project, is unique in Belgium. Moreover, the pile length of 43 m is a novelty for this type of pile. Shaft grouted piles consist of a steel profile with a separate box-like pile shoe with an open top. A thin grout is injected via an injection pipe during driving and emerges just above the pile shoe. As the pile is driven further down, so compressing the ground, the space above the pile foot is immediately filled with grout under pressure. This piling system is ideally suited for the transfer of high tensile loadings. It is a method to increase geotechnical load-bearing capacity and to reduce negative skin friction during pile driving.

Sep 1, 2022

"What can we do in ground engineering to reduce damage to the environment, to repair historic pollution, to reduce our demand on basic resources and to reduce the carbon footprint of our industry? Some developments in geotechnical engineering are already heading in the right direction. These include reductions of ground pollution from grouting, improved dewatering procedures and advances in mix-in-place processes, ground improvement and jet grouting.There is increased interest in certain promising technologies (for example, drilled partial or full displacement piles), but this approach remains for the moment somewhat avant-garde. These piles require substantially greater power to install, and the overall sustainability balance for general application has yet to be shown to be in their favour. They are particularly suited to polluted sites where the problem of dealing with spoil would be costly and where, in the past, driven cast in-situ piles would have been employed. Drilled displacement piles offer some environmental benefit over driven piles in that they cause far less drawdown of potentially contaminated near-surface ground into sensitive, underlying aquifers.There is also great interest in various means of increasing the frictional capacity of bored piles, both conventional auger and continuous flight auger (CFA) piles, by threading or ribbing the soil/pile interface. The increase in adhesion capacity allows reduction in the pile dimensions necessary for a specific load. This obviously leads to less construction waste, but also to less permanent material consumption in the piles and also in the pile caps.The role of ground improvement remains significant for brown land sites and lower capacity foundations. Information technology (IT) has improved the quality assurance of stone column construction, for example. From the sustainability point of view, this is a good news method; here is no cement, no pollution and little obstruction to future redevelopment. We now need to introduce recycled crushed materials instead of natural aggregate as general practice and the technique’s green credentials will be really compelling."

Jan 1, 2009

By Kevin Baumgartner, Steven Babcock

A landfill in Phoenix, AZ reached capacity and was graded over in the 1970s. The property was subdivided into lots in 2007 to create a business park. However, the challenging site conditions caused by the underlaying landfill put into question the feasibility of typical deep foundation systems. Several different foundation systems were evaluated to support the proposed development. The considered systems were: drilled concrete shaft, driven piles, drilled micropiles and helical piles. Soil stability, landfill decomposition, method of installation, flexibility of design, anticipated material, and equipment costs were considered. A system of helical piles with concrete pile caps and grade beams was selected. To mitigate unknown obstructions, holes were drilled through the landfill debris at pile locations and then backfilled with screened granular material. The helical piles were installed through these backfilled holes and advanced to bear in competent native material below the landfill. This method allowed for minimal disturbance of the landfill materials and provided a strong and adaptable foundation. Additional advantages of helical piles on this site include minimal installation vibration, no grout or concrete in the deep foundation, and capacity verification for each pile via torque correlation. Two load tests were performed to verify the design.

Sep 8, 2021

By Eric S. Lindquist, Charles A. Luxford

The State of Texas recently adopted a master plan to expand the existing Capitol Complex in Austin. Phase 1 of this expansion will add two new State office buildings and five levels of underground parking to the existing Complex. Additionally, a landscaped pedestrian mall will be built atop a portion of the underground parking to enhance the area as a cultural destination. Capitol Complex website: https://www.tfc-ccp.org/ Brierley Associates was selected to provide detailed design of the entire Phase 1 earth retention system for an approximately 40-65 ft (12-20 m) deep, 500,000+ yd3 (380,000+ m3) excavation through overburden soils and limestone bedrock. To facilitate overall project coordination, all design packages were required to develop Revit models, including the retention system package. With the project located in an urban setting, this 3D model also facilitated coordination of the retention system with adjacent major structures and utilities. The retention system is a combination of soil nails, soldier piling with tiebacks and rock anchors with a shotcrete facing as a substrate for the below-grade blindside waterproofing system. Due to the substantial scope of excavation, a significant number of utilities had to be routed on a temporary span over the excavation. Brierley Associates designed this utility support structure, which required extensive coordination with the excavation support and existing utilities located directly underneath the structure’s foundations. Preconstruction geotechnical work identified a fault zone that might be encountered within the excavation; however, the fault feature was found to have a more adverse location and orientation than originally anticipated. This observation required that a portion of the temporary anchors be converted to higher-capacity, corrosion-protected permanent anchors.

By Carlandrea Albonico, Salvatore Miranda

The paper describes an innovative geotechnical engineering solution that has been provided within the scope of the Galataport Project, in Istanbul, Turkey. Among all interesting geotechnical works included in the Project, this paper presents the design principle, adopted technologies and performance controls related to the Multi- Purpose Bottom Plug (MPBP). This original geotechnical engineering solution has been employed for the deep basement excavation in Karaköy and consists of a combination of seepage control, ground improvement, and load bearing elements, which have been executed with double-fluid jet grouting, pseudo-elliptical jet grouting and permanent micropiles, respectively. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By Thomas W. Scott, Manh N. Tran

Marine environments present a range of challenges for pile construction. This paper contains a discussion on the design and construction of marine piles for a recent Toll Shipping wharf upgrade in Burnie, Tasmania. The project involved several new structures including mooring, berthing and ramp dolphins supported by driven tubular piles with rock sockets, and an onshore mooring dolphin and ramp abutment supported by bored piles. Through the project, a range of construction challenges were experienced, including availability of tubular piles, the different penetration depths of driven piles into rock, the ability to drill out sockets when the piles were raked, the difficulty in verifying the design intent, latent conditions and ship impacts. The paper will present a summary of the different factors that influenced design concepts for the structures involved in the upgrade, and the challenges involved in the design of the structures. Following this, the paper will describe the methodology used to verify the design (including a pullout test), observations made during pile construction and lessons learned on how to limit risk throughout construction.

Nov 1, 2022

By Phillip E. Glogowski, N. Catherine Bazan-Arias

Steel foundations can be designed to cross-sectional configurations ranging from triangular and square to other multi-side shapes. Adding lateral extensions (hereby called wings) along the length of the steel stem can increase the foundation’s uplift, torsional and lateral load capacities. DiGioia Gray staff developed a methodology for the optimal design for multi-facetted, winged deep steel foundations. A finite element (FE) model is used to represent the steel components and the nonlinear subsurface behavior. The geometry of the foundation can be complex; thus, an optimal design needs to be fine-tuned to the specific site conditions. We created a pre-processor tool to generate the FE model including varying values for the number and size of wings, depths of embedment, reveal/stickup heights, top plate geometries, and subsurface profiles. The analytical model has been partially validated through full-scale testing and the methodology has been applied to two installed projects to date.

Sep 8, 2021

By Hayel M. El-Naggar, Mohamed Sobhi, Mamdouh M. Hamza, Marawan M. Shahien

"This paper presents the results of two lateral load tests on large bored piles in soft clay deposit for a major site in northern Egypt. The tests are carried out on 0.8 m diameter piles. One of the tests is carried out on the pile where the clay starts from the ground surface. The other test is carried out on a pile after surface improvement by replacing the top 1.50 m of the clay deposit by compacted granular soil. The results of the tests show the influence of the surface replacement layer on the lateral load versus lateral displacement relationships of the loaded pile. The results of the two tests are used to calibrate a 3D Finite Element Analysis model for the pile. The model is used to investigate the influence of the thickness and lateral extent of the surface replacement layer on the behavior of laterally loaded large bored piles.INTRODUCTIONLateral loads for piles are produced by seismic events, wind, wave action, ship impact, traffic, and land slide forces. The lateral resistance of a pile is controlled by the stiffness and the strength of the material of the pile and the soil surrounding the upper portion of the pile. In most situations, the soil surrounding the upper portion of the pile is too weak to sustain the design lateral loads. Thus there is a need to increase the lateral resistance of the pile or groups of piles. Such an increase may be achieved by either increase number of piles or increase pile diameter. Alternatively, an economic way to increase the lateral resistance is to improve the soil surrounding the upper portion of the pile (Rollins and Brown, 2011; Faro et al., 2015).Ground improvement has the ability to increase the lateral resistance of the pile by increasing the passive resistance of the soil surrounding the upper portion of the pile. The ground improvement techniques have the potential for being more cost-effective and reducing construction time. In spite of this fact, such techniques are rarely implemented in practice. Further, there are relatively few tests or records available in the literature to guide engineers in evaluating the actual effectiveness of this approach. In addition, there is no standard or methodology to aid engineers in designing increase of lateral resistance with surface ground improvement. There are specific improvement methods for each soil type, whether it is loose cohesionless soil or soft cohesive soil and these methods are provided by Michell (1981), Tershai and Juran (2000), ASCE (1997), and Rollins and Brown (2011). Furthermore, there are number of case histories that add a new hole in the sight, such as the cases provided by Brown et al. (1987, 1988), Mokwa and Duncan (2001), Rollins et al. (2005), Rollins and Cole (2006), Cole and Rollins (2006), Rollins, Snyder et al. (2010) , Rollins, Gerber, and Kwon (2010), Rollins and Nasr (2010), and Gerber et al. (2010)."

Jan 1, 2016

By Jason Herron, Joseph Brown

The common couplings for joining sections of helical piles with an outside diameter of 6.625 inches and 8.625 inches are square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. Each coupling type has advantages and disadvantages in efficiency, capacity, installation, and economics of the installed pile. All these coupling types have been used in the helical pile market in North America for various applications and designs. Many of these applications require on-site testing, but test records are not typically shared with the helical pile industry. Due to the lack of information available for square on square and flange to flange couplings, testing was done to compare the efficiency of installation, load to deflection response, and torque to capacity ratios of external pipe sleeve, square on square, and flange to flange couplings. Field installations and tension tests were performed in non-cohesive (sand type) soil near Caseyville, IL and in cohesive (clay type) soil in Centralia, MO. The data collected during these tests included rotations per foot during installation, installation torque, applied pressure, and deflection. The results of this testing are analyzed and discussed within this paper. The results indicate that the square to square coupling is the most efficient of the designs tested, but this conclusion cannot be fully justified without further testing due to the variability in the data gathered and the small number of piles tested. INTRODUCTION A helical pile is typically assumed to be a medium-displacement pile when its outside diameter is between 4.5 inches and 8 inches and a high-displacement pile when its outside diameter is greater than 8 inches. A helical pile designer has multiple options when selecting a coupling type for medium- to high-displacement helical piles. Each type of coupling has advantages and disadvantages and must be analyzed on the bases of efficiency, capacity, installation, and economics of a project. Typical couplings that are chosen by designers include square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. A helical pile must transfer axial, lateral, bending moment, and torsional loads, and the coupling must be designed to effectively and efficiently transfer each type of load. During the installation of a helical pile, the rate of penetration and the disturbance of soil layers play a critical role in the efficiency and torque to capacity ratio (Kt) of the pile. It is common for a coupling to protrude beyond the outside diameter of the pipe section being used. This is necessary for the function of certain coupling types and can facilitate the connection of couplings. However, it causes increased soil disturbance and reduce the rate of penetration due to soil bearing against the protruding portion of the coupling. A helical pile designer typically will work to minimize the coupling protrusion and create a pile with optimal installation efficiency but may choose a design with lower installation efficiency if it offers sufficient economic advantage.

Jan 1, 2019

By Jeremiah M. Jezerski, Russell H. Lutch

The Mount Olivet Road Drop Shaft (MOR-DS) support of excavation (SOE) is a circular unreinforced concrete shaft with an inside diameter of a 30.5 ft (9.3 m) and depth of 120.5 ft (36.7 m), constructed using slurry wall methods. The SOE for the adjacent Mount Olivet Road Approach Channel (MOR-AC) and Mount Olivet Road Ventilation Vault (MOR-VV) near surface structures (NSS) consists of lean mix concrete walls and cement-bentonite walls, respectively, both constructed using slurry wall techniques and reinforced with embedded soldier piles. NSS SOE required multiple levels of preloaded internal bracing, with excavation depths of up to 75 ft (22.9 m). The original design construction sequence for the shaft and NSS SOE required that the MOR-DS be constructed in its entirety and backfilled to ground surface prior to excavation of the adjacent NSS SOE. After installation of the drop shaft and NSS SOE an accelerated construction sequence was implemented requiring the analysis of the excavation support systems to determine if the excavations could be open concurrently without adversely impacting the partially constructed permanent MOR-DS structure. The MOR-DS was analyzed using the finite element analysis (FEA) software, MIDAS GTS, to demonstrate that the unbalanced loads applied to the MOR-DS composite structure due to the revised sequence would not exceed the strength and serviceability requirements per ACI-350 or superseded by the more stringent project requirements. The results of the FEA were used to set limits for geotechnical instrumentation consisting of strain gauges located on the brace levels of the NSS SOE. A comparison of the SOE design hand calculations, FEA model results and instrumentation data is presented.

Oct 1, 2022

By Sanjay Gupta, Sorabh Gupta, Ravi Sundaram, Abraham Varghese

"Geotechnical investigation for the Kochi Metro revealed a critical section of the Viaduct near Ernakulam Junction Railway Station. Four piers, located over a 220 m stretch, were passing through an area with substantial thickness of soft clay. The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear test was conducted at different depths in addition to the routine SPT. The design of heavily loaded piles in such strata is a challenge due to the liquefaction of the shallow sands and negative skin friction / down-drag in the soft under-consolidated clay. Bored cast-in-situ piles of 1500 mm diameter extending to 50-60 m depth were used to carry 500-600 tonnes load.INTRODUCTIONThe first phase of the rapid transit system at Kochi, Kerala (See Fig. 1) whose elevated route spans from Aluva to Thripunithura covers a total distance of about 25 kilometers. One of the more critical sections of the viaduct exists near the Ernakulam Junction Railway station where the alignment takes a sharp curve to move towards Vyttila, crossing the railway tracks and running partially over the approach of South over-bridge.In this section, four piers located on either side of the railway tracks near the Route Relay Cabin of Ernakulam Junction Railway Station pass through an area with substantial thickness of soft underconsolidated clay.The alignment is geotechincally challenging due to the presence of loose liquefiable sand and soft underconsolidated and sensitive clay.Initial investigations by the owner based on limited boreholes only yielded conservative and inconclusive pile capacities. For a thorough understanding of the soil behaviour, a detailed geotechnical investigation was carried out to assess the engineering behaviour of the soil strata.The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear tests were conducted at different depths in addition to the routine SPT."

Jan 1, 2015

By Xavier Pita, Alexandre Pinto, António Cristovão, Rui Tomásio

"The cutter soil mixing technology was been applied in Portugal since the last seven years. The aim of this paper is to present the main design and execution criteria, related with both the cofferdam and foundations solutions, using soil-cement panels, reinforced with steel profiles, at the new Leixões Cruise Terminal, located at the Leixões Port, in Portugal. The Terminal building was built with one basement on a marine environment, over very difficult geological and geotechnical conditions, which demanded the use of some unusual and integrated geotechnical solutions. It is also pointed out the importance of the QC/QA, as well as the technical, economic and environmental advantages of the cutter soil mixing technique, comparing with same more conventional solutions.1 INTRODUCTIONThe construction of the new Cruise Terminal at Leixões, main gate of the Atlantic Ocean to the North of Portugal and Spain, as a consequence to the constant increase of the cruise traffic, was a challenge from both the geotechnical and structural point of views, mainly due to very difficult and unusual conditions, ranging from the geological and geotechnical scenario to the existent and under operation Leixões Port infrastructures, mainly the South break water, as well as the existent cruising boarding deck (Figure 1).According to the Terminal Project it was necessary to build one basement below the water table level, including several earth retaining structures in order to allow the excavation works on dry conditions leading to a global cofferdam effect. For this purpose soil - cement panels, using CSM technology, reinforced with steel profiles, micropiles (both for foundation and cut off effect) and the existent sheet piles were used. Also pointed out are the adopted special foundations of a very complex structure, including bored piles and micropiles (Figure 1)."

Jan 1, 2015

By Unnikrishnan Nair, Sandeep S. Nikam, Sanjay D. Patil, Prabir C. Basu

"Mumbai Metropolitan Region Development Authority (MMRDA) entrusted to implement Monorail Systems in various parts of Mumbai Metropolitan Region (MMR) with the objective to supplement the present transport system in MMR. The stretch of Monorail is starting from Sant Gadge Maharaj Chowk (SGMC) and extending up to Chembur Railway Station, divided into 2 phases. Construction of Phase 1 (Chembur to Wadala Depot) is complete and Phase 2 (Wadala Depot to SGMC) is under construction.Monorail runs on prestressed girder (guide beam) of span ranging from 20m to 28m supported on pier founded upon group of end bearing piles embedded in rock, pile group ranging from 2-4 piles of diameter 1000mm each.For the purpose of site characterization, geo-technical investigations were carried out along the alignment of Monorail system as mentioned above. These investigations included field and laboratory tests. The subsurface strata mainly consist of silty sand, gravel, underlain by marine clay extending up to stronger basalt rock with volcanic breccia. Overburden consisting of mainly marine clay ranging from 5.5m to 11m at all locations within the influence zone of settlement.The existing rigid pavement along of Sion-Koliwada and Anik-Wadala were constructed about 5 years prior to the construction of Monorail piers. Before laying the rigid pavement, to improve the geotechnical strength of subsoil (mainly marine clay), ground improvement using stone columns was undertaken by MMRDA. In light of limited right of way, the Monorail piers have been constructed in the median portion of the road. The line became operational on February 2014, in few months it was noticed that, in the vicinity of the Monorail piers, along Sion-Koliwada link and Anik-Wadala link, the Road Pavement Quality Concrete (PQC) panels adjacent to the Monorail piers started showing distress in form of nonuniform settlement of the concrete panels.Effect of pile foundation on pavements/PQC slab distress and possible causes of distress were investigated. Initially the distress was thought to be upheaval of monorail pier cap, but further investigations revealed the same to be soil settlement occurring over time. This paper describes the investigation carried out for identifying the cause of this settlement."

Jan 1, 2015

By Eric Lindquist, John Compagnone, Gabriel Carvajal

"Condon-Johnson & Associates, Inc. (CJA) with the assistance of design consultant, Brierley Associates, designed and installed a water tight shoring system utilizing several ground improvement techniques jointly. Prior to the installation of the shoring system, a test program consisting of the installation and testing of 7 jet grout columns; 1 soil mix panel; 7 soil anchors and 3 tie downs was performed to verify design assumptions. State-of-the-art quality control measures were employed throughout the project.The shoring system consisted of:•,Deep Soil Mixing (DSM) wall utilizing triple axis tooling to install overlapping columns along the perimeter of the proposed excavation to a treatment depth of 54 feet.•,Installation of steel piles in DSM to provide rigidity to the wall.•,Installation of a jet grout bottom seal, installed from surface to a depth of 58 feet below existing grade.•,Installation of 153 soil anchors, 1-1/4” diameter and 47’-6” length, to tie the jet grout bottom seal to the native soil below to resist hydrostatic uplift, installed from existing grade to a depth of 91 feet.•,Installation of walers and pipe struts for internal bracing•,Installation and stressing of 117 tie downs, 1” diameter and 16 ft length, to tie the pump station mat slab to the jet grout bottom seal, installed from inside the excavated pit.Subsurface conditions at the site consist of uncontrolled fill materials to a depth of 20 feet comprised of sandy silt and clayey sand. The native soils underlying the fill generally consist of soft and compressible lean clay and silt with varying amounts of sands to a depth ranging from approximately 44 to 54 feet below ground surface, which in turn are underlain by dense to very dense silty sand. The groundwater elevation at the site is approximately 8 feet below ground surface.This paper covers the design aspects, construction, and quality control measures undertaken by the geotechnical contractor, with supporting figures.INTRODUCTIONThe owner, County Sanitation District No. 2 of Los Angeles County, designed upgrades to their existing Long Beach Main Pumping Plant Facility. The upgrades consist of a new pump station that includes a reinforced concrete below-grade wet well and dry well, a two-story operations building, two 78-inch diameter pipe inlets, two 42-inch diameter discharge pipelines connecting the existing manifold, two pipe junction structures, two insert-type junction structures, and electrical transformers. This paper focuses on the excavation shoring for the new pump station. The original shoring design concept for the pump station excavation illustrated on the contract plans consisted of pressed in sheet piles, a jet grouted bottom seal with soil anchors, 2 levels of internal bracing, and tie-down anchors to resist hydraulic uplift forces on the buried pump station."

Jan 1, 2017

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016