Search Documents

By G. B. Harris

A process for the recovery of copper from the waste oxide copper of a mined-out sulphide orebody is described. Hydrometallurgical recovery of copper from this and similar wastes has been tried several times previously without success. Leaching is carried out by sulphuric acid in columns under conditions that minimise the iron content of the pregnant leach liquor, and copper is then recovered by ion exchange rather than the more conventional solvent extraction. The resin is stripped by spent electrolyte and copper is electrowon. Results are presented for testwork originally carried out in 1993, and repeated in 2006, and the novel aspects of the process, leaching and ion exchange, are discussed. Finally, preliminary order of magnitude capital and operating costs are given, demonstrating that the process is cost effective.

Jan 1, 2007

By R. A. L. Drew, C. A. Rodríguez González, Caleym W. F.

This work addresses the need of new refractories for copper converters. Technological improvements and environmental regulations for chromium containing refractories have generated this need. Chemical interactions, mechanism of penetration and the effect of oxygen potential and temperature in the system Cu2S-FeS-SiO2-O2 are presented for two refractories: a burned magnesite chrome brick (typically used by the copper industry) and a chrome-free spinel direct bonded brick. The main difference determined in the refractory performance was the blister copper penetration resistance; burned magnesite chrome brick is penetrated while direct bonded brick is not. These results are very promising since blister copper penetration has been reported as the major cause of refractory wear. The results are explained in terms of refractory porosity and wetting characteristics.

Jan 1, 2004

By S. Xu, A. Ramesh, F El-dabbagh, Z. Fang, A. Sobhy, J. A. Kozinski

Waste remediation is a goal that will be driven forward by economic conditions. As the cost of waste disposal increases, new methods of waste reduction will become economically attractive, and will be implemented. It is difficult to imagine, however, a time when there will be no waste generation. For the foreseeable future, despite effective reduction practices, there will still be hundreds of millions of tons of waste that must be destroyed or controlled to protect the public health and the sanctity of the environment. To remain faithful to environmental covenants, the mineral and metallurgical industries will face these new challenges. This paper discusses novel waste remediation approaches and techniques focusing on hazardous wastes and thermal remediation. Aspects concerning technological and environmental importance are examined. Solutions for neutralization of environmentally hazardous compounds are proposed.

Jan 1, 2004

By P. Molera

"In Catalonia, between the 10th century and 1878, some installations were developed which at first were called ""factories"" and later ""fargas"", since they manufactured iron and steel of low carbon content. Because of its excellent quality, the fame of this metal spread from Catalonia to many countries. Fargas were started in Corsica, the Low Countries, Germany, Oriental India, Madagascar, Finland and along the rivers Orinoco and Mississippi among others. The extractive process used in these fargas has passed into history as the ""Catalan Farga Process"", ""Catalan Process"", or just ""Farga Catalana"". With this technology, raw material was obtained for the fabrication of tools, nails, weapons, grilles, etc. to supply the national and export markets. Aside from meteorites and native iron, found as metallic nodules in basalts in Greenland and Palestine, the ancient civilizations, which had no means to reach the fusion temperature of iron (1535°C), obtained iron by a direct process. Similar processes were used until quite recently (1930s) by certain tribes in Central Africa; holes in the ground were filled with iron ore and coal, and combustion encouraged by blowing air by mouth or with bellows made of animal skins. Thus without melting the iron it is possible to reduce the mineral and obtain a porous and impure metallic mass, which is purified on forging by mechanical squeezing. With a process very likely similar, the famous column at Dehli weighing 6.4 m.t. was built about 300 B.C."

Jan 1, 1999

By K. V. Gow, F. A. Jerabek

"THE NOVA SCOTIA TECHNICAL COLLEGE has been granting degrees in mining engineering since 1909. The college was established in 1907 to provide the final two years of the undergraduate program in engineering the earlier years of which are given at several small universities scattered around the Atlantic Provinces. Since the beginning of the program, 251 Bachelor of Engineering degrees have been awarded in mining engineering. Although the average class size has been small, increases in enrolment in the past few years have resulted in Nova Scotia Technical College being the second largest mining department in Canada, based on the number of graduates per year. This year 18 students received B.Eng. degrees, and next year 17 will graduate.In 1968, it was necessary to make a decision on whether or not to abandon, for economic reasons, the program in mining engineering. For several years enrolment had been very low and resignations among the mining engineering staff created a situation in which the program could easily have been dropped. However, it was decided to continue mining engineering, as it was the only such program in the Atlantic Provinces. New staff members with many years of practical experience in the mineral industry, not only in Canada but in the U.S.A., South America, Africa and the U.K., joined our department. At the same time the enrolment in mining engineering began to increase significantly."

Jan 1, 1972

By J. W. Matousek

Since the late 1800s, copper-nickel ores have been mined and smelted in the Sudbury area. The Canadian Copper Company, the Copper Cliff ancestor of Inco Limited, commenced operations with a blast furnace smelter in 1888. Coal-fired reverberatory furnaces were added in 1911 and multihearth roasters in 1914. The blast and reverberatory furnaces smelted, respectively, coppernickel ores and ore fines until 1930, when a milling process and plant began operating to concentrate and separate the minerals of these two metals. Two reasons for this delay were: (1) the availability of high grade ores suitable for direct smelting; and (2) the difficulties in making the copper-nickel separation. The Mond Nickel Company, however, practiced flotation at its Coniston Smelter site from 1914 to 1930. A bulk concentrate containing six per cent copper and five per cent nickel was recovered from ore of 1.6 per cent each of copper and nickel. Gravity (table) and magnetic concentrates were also produced. Inco Limited (then The International Nickel Company) began laboratory-scale flotation tests on its ores in 1918. This work led, ultimately (in 1930), to the construction of the 7500 tonne-per-day Copper Cliff Mill, designed to recover separate copper and nickel concentrates. Its capacity was expanded to 11000 tpd in 1936, to 18 000 in 1940, and to 27 000 in 1942. Since 1971 it has operated to process only the bulk flotation products from other mills to yield individual nickel and copper concentrates.

Jan 1, 1999

The Boleo project is located in Mexico close to the town of Santa Rosalia on the Baja Peninsula. The Boleo deposit contains copper, cobalt, zinc and manganese values as oxides with minor sulfides. The Boleo deposit is metallurgically challenging due to: 1) the requirement to recover four separate metals; 2) the presence of high levels of clay in the deposit resulting in difficult solid-liquid separations, and; 3) the need to use seawater for the bulk of the processing. Baja Mining, Bateman Engineering and SGS Lakefield Research have collaborated to develop and test a process flowsheet to recover copper, cobalt, zinc and manganese products at Boleo. The key steps in the flowsheet are: ? Feed preparation (scrubbing and ball milling of oversize) in copper raffinate ? Ore leaching using oxidative and reductive leaching ? CCD washing using high rate thickening technology ? Copper SXlEW ? Treatment of a bleed solution for cobalt, zinc and manganese recovery The process for cobalt, zinc and manganese recovery involves iron and aluminum removal followed by cobalt/zinc bulk extraction using CSIRO's DSX solvent extraction system and selective zinc and cobalt stripping. The zinc strip solution is evaporated to produce zinc sulfate monohydrate crystals to market and cobalt is recovered via a further SXlEW process as high purity metal. Manganese is precipitated as manganese carbonate from the DSX raffinate solution. This paper will review the Boleo process flowsheet and provide detailed results from the 2006 pilot plant operation conducted at SGS Lakefield in Canada.

Jan 1, 2007

By M. Olper

Commercial copper plants utilising current best technology are tending towards ever increasing scale, the concentrate requirements of which cannot be serviced by a single mine. In such cases, raw materials are often sourced from different mines, which are often far away from the production plant and usually with very different ore compositions. These plants tend to use the traditional thermal processing steps of smelting, converting to blister, anode refining and casting to produce copper anodes that are then refined in a sulphate electrorefining operation. These thermal steps are in some cases troublesome and require the recycling of considerable quantities of material. A new process was developed taking advantage of the latest developments of the first thermal step of the classic loop, the smelting of copper concentrate to high grade matte or white metal using the well known AUSMELT Top Submerged Lancing Technology. The white metal and/or high grade matte product is converted directly to copper cathode and elemental sulphur using the ECUPREX technology. This approach provides an alternative to the traditional thermal steps of conversion to blister, thermal refining and anode casting, which, especially at small scale, can be expensive and problematic in terms of technical and environmental concerns. At first evaluation, this new process can be operated at low capacities, thereby, changing the traditional approach to copper production. Instead of taking the concentrate to the copper production plant, the copper production plant is taken close to the mine with some significant economic and technical advantages.

Jan 1, 2007

By Alex Henderson

The underground hard rock mining industry has had little change since the mobile equipment era began in the 1970s. Equipment has become larger and faster but has not kept pace with the following challenges: ? Improvements in safe production, ? Increasing demand for metals, ? Environmental improvements, ? Decreasing grades, ? Increasing depth of mining, ? More metal from underground vs. surface mining, and ? Energy and green house gas awareness. We are on the cusp of a new mining era and must rethink how underground hard rock mining must change in order to meet these challenges. This paper will show historical changes and propose a set of guiding principles for the next era of mining. Mining has changed over the last century. Initially mining was primarily an endeavor carried on by private companies with minor environmental controls and few social expectations other than employment. In the mid to later part of the century the mining industry was facing new challenges: deeper mines, the London Metals Exchange markets for pricing, and environmental concerns related to acidic rock drainage coming to the forefront. In today?s context, mining has evolved in complexity with the social and environmental aspects equally or surpassing the technical complexities such as expanding from mining hard rock to laterites, and mining lower grades or at greater depths. Nowadays, communities must be considered as partners, both locally and globally and the increased international visibility pushes the mining sector to take a more balanced approach to the business of mining (Fig. 1).

May 1, 2011

By P. L. Drake

This paper comprises a discussion of the role which mineral resources will play in Canada's future export trade and the growing demand for minerals in Canada.

Jan 1, 1979

By K. Kim

"All milling operations would like to achieve the best possible recovery in combination with the highest achievable throughput. Unfortunately, many operations have problems with low recovery, low throughput or both. In the majority of these cases investigated by the author, the solutions to improve recovery and throughput were simple. The solutions did not include implementation of new technology or major capital, but rather a return to fundamentals. In most cases, problems occurred because the operation was not following their own operating procedures, because the design of the circuit was changed without adequate change management or understanding of the implications of changes, or because basic metallurgical measurements and control were not taken or ignored. In this paper, examples of these problems and their solutions derived from long and varied experience will be discussed. The objective of this presentation is to provide the milling operator with practical and readily implementable solutions to common milling issues to improve throughput and recovery.INTRODUCTION Mill operations can be evaluated by many operating parameters, but the two best indicators are recovery and throughput. These two parameters summarize the wellbeing of an operation. The grade to the mill is also a good indicator, but this is usually controlled by the mine. The best recovery and throughput are achieved through a team work involving operators, maintenance workers and metallurgical staff. The milling operations include many unit operations, such as crushing, grinding, flotation, leaching, carbon in leach, Merrill Crowe, roaster, autoclave and refinery. The tools available to the operations are plant design, process measurements, assays, metallurgical balance, and operating strategy. Twelve real life examples of improvements of recovery and throughput are presented in this paper. EXAMPLE 1: CRUSHING CIRCUIT WITHOUT FINE ORE BIN At this operation plant throughput could not be maintained at a high rate because feed to the mill became coarse during the day. The cone crusher was feeding the ball mill directly. As the day wore on, the gap on the cone crusher would slowly increase, which would cause the product size to increase. This would increase the re-circulating load on the ball mill. The throughput would decrease accordingly. Furthermore, the throughput would decrease more with high frequency of maintenance on the cone crusher."

Jan 1, 2019

"In the UK, Ireland, and Western Europe, the mineral resource and reserve reporting standard is the PERC Code, developed and maintained by the Pan-European Reserves and Resources Reporting Committee, which is a standing committee set up under the auspices of a number of professional organisations which include the Institute of Materials, Minerals and Mining (loM3), the Geological Society of London (GSL), the European Federation of Geologists (EFG) and the Institute of Geologists of Ireland (IGI) to develop a Pan-European reporting code. The PERC Code supercedes the old IMMM Reporting Code 2001 and is recognised by the UK securities regulators and stock exchanges.""FOREWORD1 The Pan European Reserves and Resources Reporting Committee (PERC) Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (further referred to as 'the Code') sets out minimum standards, recommendations and guidelines for Public Reporting of Exploration Results, Mineral Resources and Mineral Reserves in the United Kingdom, Ireland and Europe. The history of development of this code is summarised in Appendix 4.This 2008 edition supersedes all previous editions of The Reporting Code and the IMM Reporting Code.INTRODUCTION2 In this edition of the PERC Code, important terms and their definitions are highlighted in bold text. The guidelines are placed after the respective Code clauses using indented italics. They are intended to provide assistance and guidance to users in interpreting the application of the clauses in the Code. The same indented italics typeface formatting has been applied to Table 1, and to Appendices 1 and 2 which form part of the Guidelines.3 The Code has been adopted by the Institute of Materials, Minerals and Mining (loM3), the Geological Society of London (GSL), the European Federation of Geologists (EFG) and the Institute of Geologists of Ireland (IGI), and is therefore binding on their individual members.Appendix 1 contains a table of generic terms and their equivalents, designed to avoid unnecessary duplication or ambiguity in the textAppendix 2 provides Rules of Conduct for Mineral Resource and Mineral Reserve estimators that should be considered in addition to the Codes of Ethics normally applying to members of professional institutions."

Jan 1, 2003

By Benoît Plante

La mine Tio (QIT Fer et Titane Inc.) exploite à ciel ouvert un gisement d?ilménite massive depuis 1950, générant jusqu?à maintenant plus de 70 Mt de roches stériles potentiellement génératrices de drainage neutre contaminé (DNC), dont une partie est submergée dans le lac Petitpas, au nord de la mine. Si généralement l?ennoiement des rejets miniers a un effet bénéfique pour limiter la contamination des eaux, cela reste à prouver pour ce qui est des stériles générateurs de DNC. Des essais en réservoirs ont été réalisés afin d?évaluer la réactivité de trois différents types de stériles submergés, qui ont été choisis en fonction de leur teneur en ilménite. Afin d?évaluer l?impact de la matière organique sur la réactivité des stériles submergés, chaque type de stérile est étudié en immersion simple ainsi que combinée à des sédiments prélevés au lac Allard, à proximité de la mine, d?où l?eau utilisée dans les essais a aussi été prélevée. L?évolution des teneurs en Ca, Mg, Si et Ni durant les 8 premiers mois d?étude démontrent que les stériles immergés sont réactifs, mais l?impact de la matière organique demeure pour l?instant difficile à préciser. Tank tests on Tio mine waste rock The Tio mine (QIT Iron and Titanium Inc.) exploits a massive ilmenite ore as an open pit since 1950, producing over 70Mt of potentially contaminated neutral drainage (CND)-generating waste rocks. While the underwater disposal of mine wastes generally show a beneficial effect on water contamination, this method still needs to be approved for CND-generating waste rocks. Tank tests were realized in order to evaluate the reactivity in underwater conditions of 3 different waste rock types, chosen with regards to their ilmenite content. In order to evaluate the impact of organic matter on the reactivity of underwater waste rock, each waste rock type was studied in simple immersion and in combination with sediments sampled at Allard lake, located near the mine, where the water for the tests was also sampled. The evolution of Ca, Mg, Si and Ni during the 8 first months of testing show that the waste rocks are reactive underwater, but the impact of the organic matter is till hard to define.

Nov 1, 2008

By Denis Bois

La Bolivie est un pays en développement qui compte une tradition minière qui précède même l?établissement espagnol en Amérique. Pendant toutes ces années, l?exploitation minière s?est faite sans grands égards pour l?environnement. Au cours des dernières années cependant, le gouvernement bolivien a modifié ses lois afin de rendre nécessaire la prise en compte de l?environnement dans le processus d?exploitation d?une mine. Dans le cadre d?un projet MRN-ACDI1 visant à renforcer le secteur minier en Bolivie et ses retombées pour la population, l?URSTM2 a été mandaté pour développer et mettre en place un programme académique de gestion environnementale minière, basée sur l?expertise canadienne. Ce programme vise à renforcer les institutions académiques boliviennes responsables de la formation en environnement minier en Bolivie ainsi que les ministères et agences gouvernementales concernées.

May 1, 2001

By H. M. A. Rice

"The Ainsworth mining camp is on the west side of Kootenay lake; British Columbia; 14 miles south of the town of Kaslo. It is in one of the oldest mining districts in central British Columbia; for mining started there in 1888. Its principal production was between 1905 and 1920. Activity since then has been sporadic. According to available records; some 222; 000 tons of ore had been produced from the camp up to 1942.GENERAL GEOLOGY Bedrock in the district consists of a succession of quartzite, quartz-mica schist, hornblende schist, and limestone of Late Precambrian, Carboniferous, and Triassic age. Most of the hornblende schists are of volcanic origin but some formed from related intrusions. The Nelson granodiorite batholith of Jurassic age borders the camp on the west. There is also a series of basic dykes of much later age."

Jan 1, 1954

By S. Brophy

Controlled Short Circuit ? Metal Inert Gas (CSC-MIG) welding is a process that can be referred as a "Cold Welding" technology. The CSC process is based on accurate control of the welding wire position, thus the mandatory requirement for the automation of the process. One of the main advantages of the CSC-MIG process is the rapid solidification of the deposited material, resulting in weldments displaying low porosity contents, and enabling the joining of thin sheet materials. These characteristics render this process an ideal one for freeforming of components, where rapid solidification would be efficacious. This presentation will focus on the progress made towards the freeforming of Al-based components in the NAIN laboratory at McGill University. The relationship between the filler metal used, freeforming (deposition) parameters, resulting microstructure and mechanical properties will be presented.

Jan 1, 2011

By D. G. Dixon

A novel technology for leaching copper from primary copper concentrates has been developed at UBC. This patented technology takes advantage of the galvanic couple between pyrite and chalcopyrite to ensure rapid and complete oxidation of chalcopyrite under mild conditions in acidic iron sulfate solution, without the need for microbes, ultrafine grinding, or chemical additives such as chloride, nitrate, or surfactants. Copper recoveries of 98% or greater can be achieved at 80°C under atmospheric conditions in as little as 4 hours of residence time. The process is selective for chalcopyrite over pyrite, generates near-quantitative levels of elemental sulfur, and is fully compatible with conventional solvent extraction and electrowinning of LME Grade A copper cathodes. In this paper, the fundamentals of the Galvanox ? process are reviewed, and selected results of batch leaching tests on various concentrate samples are presented and discussed.

Jan 1, 2007

By W. Grell

"In this paper, two methods of standardizing mill language are proposed; one is based on metric units and the other on English units. Tentative procedures for chemical and screen analysis based on published methods are proposed.Standard procedures for determining work index, and for leaching, flotation, and classification tests are outlined.Objects of Standardization:(1) to improve communication -(a) among gold metallurgists(b) with other branches of mineral dressing(c) with mineral dressing in other countries(d) with general scientific procedure(2) to improve mill control by -(a) standard methods of analysis (i)(ii)(iii)(b) standard methods of calcula tiort(c) standard accounting proceduresin the plantin the mill laboratoryin the assay office(3) to improve mill test work and investigationAreas of Standardization(1) Nomenclature or terminology(2) Measuring techniques(3) Test procedures(4) Accounting procedures"

Jan 1, 1966

By D. Harris, G. Ye, G. Oprea, J. Rigby, T. Troczynski

Sintering and ceramic bonding in refractory castables take place mainly in the binding system during the first heat-up and in service. Consequently the strength and the corrosion resistance of the hot face layer depend on the sintering ability of the complex mix of ceramic powders constituting the binding system. As a result, the use of nano- sized reactive powders in the binding system mixes would activate the sintering and enhance the ceramic matrix formation at temperatures below 1300°C. Our work presents the experimental data on sintering behavior of binding systems containing magnesium aluminate and alumina nano-powders in the temperature range of 800-1450°C. The results indicated that a ceramic matrix, similar to high temperature fired bricks, could be generated after firing at the relatively low temperatures available in the non-ferrous smelting furnaces.

Jan 1, 2004

By C. D. Kaeding

IN the summer of 1937, the Algoma Steel Corporation, Limited, decided to embark on the full-scale development o their Helen mine and the erection of plants to produce commercial iron sinter from its ores at a rate ? of fifteen hundred tons per day. The Helen deposit has long been known as one of the largest bodies of non-commercial iron ore in Canada, consisting almost entirely of siderite with a band of pyrite along the north wall and some lenticular inclusions of pyrite throughout the mass. It originally contained a nominal amount of hematite (2,800,000 tons), localized at the western end of the ore-body, but this was mined out during the years 1900 to 1918. For details of the:-geology of the Helen range and of the surrounding district, the reader is referred to Memoir 147, Michipicoten Iron Ranges, Geological Survey of Canada, 1926 (1). The siderite mass was explored by diamond drilling in 1917 and the portion so drilled was estimated to contain 67 million tons of siderite averaging 36.0 per cent Fe, 3.2 per cent S, and 8.2 per cent SiO,, without establishing its ultimate depth or extent. The variation in the sulphur content shown by drilling was from 1.5 per cent in 72 per cent of the tonnage, to 7.2 percent in the remaining 28 percent. The pyritic ore aver-aged about 38 percent iron, but otherwise its composition was substantially the same as that of the siderite mass.

Jan 1, 1940