Search Documents

By J. E. Sepulveda, R. Morrow

"The Linear Wear Theory provides a reliable framework for the assessment of grinding media performance at full scale. This theory can be applied for analyzing grinding media consumption rates in any given grinding operation as well as the evaluation of alternative grinding media products, based on actual operational data, correcting for conditions like ore hardness, feed and product sizes, mill power and circuit throughput; all of them unrelated to the grinding media intrinsic quality attributes. A series of Moly-Cop Tools 3.0 applications have been developed to facilitate the calculations involved. Moly-Cop Tools 3.0 is available, free of charge, to all interested parties through the corresponding author.INTRODUCTION Mineral grinding circuit operators recognize the significance of grinding media (balls) consumption on the cost structure of any full scale grinding facility. The effective cost associated with this essential consumable depends on two factors: delivered price and durability (quality) of the grinding media. When evaluating alternative grinding media varieties, there is a well accepted evaluation criterion by which a given media type is considered to be “cost-effective” when its unit application cost – normally expressed in $/ton of ore ground – is shown to be lower than that of a nominal reference condition: Grinding Media Cost = Ball Price x Ball Consumption (1) ($ /ton ground) ($/ton balls) (ton balls/ton ground) Under this criterion, an alternative, higher-price grinding media product could be “cost-effective” if its associated consumption rate is sufficiently lower than the reference media, enough to yield a lower grinding cost, as dictated by Equation 1. For the proper application of the above criterion, evaluators must rely on representative indicators of grinding media quality, ideally independent of most mill operating conditions. In each particular case, ball price is always a known component; however, it is not so evident how media performance (quality) differences amongst alternative product types could be assessed with a reasonable degree of accuracy and precision."

Jan 1, 2014

By G. J. Ackland, K. Saksl, F. Brunke, M. Kohnke, B. Tegner, C. Siemers

The application of titanium alloys is limited to 550°C due to their poor oxidation resistance. It is known that the addition of niobium decelerates the oxidation of titanium alloys whereas elements like vanadium do not improve titanium’s oxidation resistance. The underlying mechanisms are not yet well understood. In the present study, different binary titanium-niobium and titanium-vanadium alloys as well as commercially pure titanium were investigated. Oxidation experiments were carried out at 800°C up to 288 hours followed by metallographic analyses to study the oxide layer morphology as well as the microstructure at the interface. Energy-dispersive X-ray spectroscopy mappings were used to identify possible changes in the distribution of the alloying elements. In addition, micro-focused hard X-ray experiments were performed to layer-wise analyse the phase composition in selected samples. As expected, the niobium containing alloys show a better oxidation performance compared to commercially pure titanium and the titanium-vanadium alloys. The oxide layer consisted of TiO2 and Ti2O3. Depending of the niobium content, a niobium-rich layer developed below the metal-oxide-interface minimising oxygen diffusion into the titanium matrix. Based on these results, the minimal niobium content needed for improved oxidation resistance was identified so that alloys of technical relevance can now be developed.

Jan 1, 2014

By Kevin M. Ansdell, Irvine R. Annesley, Christine L. Mckechnie

The U-Th-REE mineralization at Fraser Lakes Zone B is hosted by granitic pegmatites and leucogranites, which lie along the deformed contact between Paleoproterozoic metasedimentary gneiss of the Wollaston Group and Archean orthogneiss, approximately 25 km from the southeastern edge of the Athabasca Basin. The pegmatites/leucogranites are subcordant to concordant with the regional foliation and are concentrated within a northeast-plunging antiformal fold nose, the study area, which lies west of Fraser Lakes. The mineralized pegmatites/leucogranites in the western part of the study area (Group A) are typically enriched in U (± Th) with Th/U ~1, and contain uraninite, thorite, zircon, and allanite. Those intruding the central part of the study area (Group B) are generally enriched in Th and LREE, with Th/U >2, and contain monazite, thorite (commonly U-enriched), and zircon. The pegmatites and leucogranites in Group A tend to be slightly enriched in SiO2 and depleted in TiO2 relative to those in Group B and are interpreted to represent more evolved crustal melts. Both groups are peraluminous and show varied chemistry. Partial melting (~850ºC and 9 kbar) of a metasedimentary rock-dominated source, entrainment of accessory minerals as xenocrysts, and assimilation-fractional crystallization processes combined to enrich the granitic pegmatites/leucogranites in U, Th, and REE elements. Transfer of melt from the source region to the crystallization sites was assisted by deformation within and along major structural zones, such as the folded Archean-Paleoproterozoic discontinuity. The character of mineralization and structural control in the study area is reminiscent of the alaskite-hosted deposits at Rössing, Namibia.

Jan 1, 2013

By Valérie Tremblay

Plan de la presentation ?Laboratoire d?analyse des fluids ?Gestion des contaminants ?Condition Monitoring Avantages reliés aux analyses ?En savoir plus!! ?pour minimiser les coûts d?opération; ?pour prévenir les défaillances catastrophiques; ?pour maximiser le rendement des équipements; ?pour maximiser la longévitédes équipements; ?pour permettre des périodes d?entretien planifié.

Feb 1, 2008

By W. H. Zieman

"THIS IS THE THIRD of the consecutive Annual Forums on Grinding that were instituted by Mr. L. E. Djingheuzian in 1957. The first was on the subject of Ball Milling (Transactions, Volume LX, 1957) and the second on The N on-Cataracting Ball Mill (Trans-actions, Volume LXI, 1958). From the discussions at these forums it was evident that one of the most important factors affecting the efficiency of grinding is the shape of the liners. In order to make a study of liners in use, it was •decided to seek the co-operation of operators across the country by sending out questionnaires requesting basic information. Additionally, these operators were urged to set down briefly any pertinent information on the subject acquired through experience and experiments at their own particular plants. A compilation and analysis of these data were to form a basis for discussion at the Forum on Liners at the Annual Meeting in Montreal, April, 1959. The response of the milling fraternity to this solicitation was most gratifying, and clearly indicated the importance attached by the operators to the effect of liner design upon overall grinding performance."

Jan 1, 1959

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By F Kelly

"A central composite experimental design was used to determine empirical relationships between the operating variables of a ball mill and the characteristics of the ground products. The independent variables selected for the study were the work index and size distribution of the feed material, the feed rate and the pulp density. The measured responses included product size distribution, product surface area, viscosity of pulp discharge, weight of dry solids in mill, mill time constant and emitted sonic vibrations. The ball mill was operated continuously in open circuit during each experimental run.Multivariable regression techniques were used to derive linear empirical models from the experimental results. Of the four factors studied, the grindability of the feed material significantly affected every measured response. The size distribution of the ground product was affected significantly by the feed rate and the size distribution of the feed, but not by the pulp• density. Feed throughput capacity and pulp density were significant to the viscosity of the pulp discharge, the weight of solids in the mill and the mill time constant. Significant first-and second-order models are given for the above relationships. The relation-ships between the characteristics of the sonic vibrations of the operating mill and the various dependent variables have not as yet been established."

Jan 1, 1970

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003

By P. O. Sandstrom

"Atlas Copco is introducing a new patented method for full-face boring. This paper presents the basic principles of the boring action and discusses the present experience regarding performance and costs. The Atlas Copco ""Full-facers"" are designed for hard-rock applications, although they are successfully boring in soft ground without major changes. The unique patented boring principle referred to as the 'Undercutting Method' permits these machines to bore, economically, in harder ground than machines based on the 'crushing principle'. This is mainly due to considerably lower cutting-tool costs, as the tungsten carbide tips only are in contact with one-third of the bored volume. The remaining rock is 'undercut' and peels off from a slight back pressure.The undercutting method also permits boring of non-circular headings and Atlas Copco has already manufactured two machines for rectangular drifts. This concept could revolutionize development work in mines employing trackless equipment."

Jan 1, 1971

By A. R. Miller, G. Desrivières, T. MacKinnon, H. Bursey, M. C. Bétournay, B. Replogle, D. L. Barnes, P. Laliberté

"A mine production locomotive, the world’s first applied industrial fuel cell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuel cell vehicles.The locomotive’s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuel cell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery- powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuel cell vehicles, and cost benefit aspects.This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable, and efficient power plant that fulfilled its design objectives, including longer productivity time for a given vehicle fill-up."

Jan 1, 2004

By Rayleen Riske

Why do we look for better reconciliation when times get tough? Why wait? Mine reconciliation should be a priority throughout the good times too. In fact, with good reconciliation, those good times are going to be even better and will help pave the way to success through those preventable bad times. Reconciliation throughout the entire mining value chain requires the capture, validation, and analysis of copious amounts of data. This task can be daunting for a team in a small mine, let alone reconciling across a suite of large mines. This paper will outline the different ways we can reconcile across the value chain, why we should reconcile over differing periods of time and how Snowden?s solution to proving reconciliation can be a simpler, reliable and transparent process. Snowden?s Reconcilor is proving to be a valuable tool on any mining scale, by capturing, validating, sorting and reporting data for timely decision making by the site geologist through to corporate management. By instigating vigorous reconciliation, you are setting your mine up for the future. Not only will you have the means to analyse your current processes and measures, but you will have the opportunity to identify and improve your mine?s performance from the resource model through to the final product.

May 1, 2010

By G. M. Brownell

THE Falcon Lake stock is a small igneous mass, 2.6 square miles in area, which has intruded a belt of older lavas and metamorphosed sediments. It is well exposed and the entire area of its outcrop is taken up with surveyed mining claims, the claim lines forming a grid which makes ideal conditions for a detailed petrographical study of the unusual variations which are found in the composition of this unit (see Figure 1). The study of this mass, which has revealed features of both scientific and economic significance, began in the summer of 1939 when trainees in a Prospectors' Training Camp, a Do-minion-Provincial youth-training project under the writer's supervision, were, detailed to map rock outcrops on various mining claims. Microscopic study of rock specimens taken on a line across this stock were made during the following winter and proved to be of such interest that a special trip was made the following summer for the purpose of gathering more data, the results of which are presented here. Location The stock is close to the southeast corner of the province of Manitoba, about three miles from the Ontario boundary. It lies between Falcon and West Hawk lakes and less than a mile south of the Trans-Canada highway. It is easily accessible by motor car, as a branch road from the highway leads to the Sunbeam Kirkland gold mine, which is within the inner core of the stock. Previous Work This area was the first in the Province to receive attention from prospectors, who entered it from the adjacent Lake of the Woods district during the days of the mining boom in the 1890's. Small occurrences of gold, copper, molybdenum, and tungsten ores were found, but to date there has been no production from the district, except for small shipments of gold ore. The regional geology has been mapped by the Manitoba Department of Mines and Natural Resources, the Falcon Lake stock being shown and recorded as of "varying composition". The more detailed work involved in preparing the accompanying map has necessitated only minor changes in the outline as previously mapped.

Jan 1, 1941

By J. R. Welsh, D. J. Palmer, O. M. G. Newman

"The use of calcine for selective zinc precipitation requires specialist knowledge to achieve satisfactory flowsheet design. Calcine from the bed of a fluid roaster is preferred, and factors such as the size distribution of ground calcine, the stoichiometric ratio of the calcine precipitant to the initial dissolved zinc concentration and the moisture content of the resultant filter cake are parameters which require critical attention. Extensive testing in a fully-integrated electrolytic zinc plant pilot plant has demonstrated that properly designed selective zinc precipitation plants using calcine as the precipitant are reliable operating units.The advantages of using calcine instead of limestone for selective zinc precipitation include a decreased cost of reagents, as well as avoiding the formation of by-product gypsum.Process simulation modelling has demonstrated that the use of calcine in this context has widespread application in the design of zinc plants with superior impurity and water balance control characteristics. A particularly powerful approach involves closed circuit washing. In this mode, filtrate from the selective zinc precipitation step is used to wash a zinc plant residue such as jarosite, and the resulting filtrate is returned to the selective zinc precipitation section. IntroductionThe Selective Zinc Precipitation (SZP) Process, developed and patented by the Electrolytic Zinc Company of Australasia Limited (EZ) may be used to achieve simultaneously, water balance and impurity control in an electrolytic zinc plantO,2). Impurities which may be controlled by the SZP process include chlorine, magnesium, manganese, potassium and sodium.In the SZP process, basic zinc sulphate is precipitated from a zinc sulphate solution by either limestone, lime or a compound containing zinc oxide, usually calcined zinc sulphide concentrate (calcine) or alternatively zinc oxide fume .The solids containing basic zinc sulphate are separated, typically, by filtration and returned to the zinc plant circuit as a neutralizing agent. The zinc depleted solution can either be discarded, or used to wash residues, thereby achieving water balance and impurity control (Fig. I)."

Jan 1, 1988

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By K. D. Hester

This paper will review the metallurgical aspects of the completed expansion program at Quirke, and the current rehabilitation and refurbishing program at Panel. During the Quirke program, completed at the end of 1977, the plant capacity was increased from a nominal 4,500 to 7,000 short tons per milling day. The expansion of crushing, grinding, neutral thickening and filtering, leaching, partial neutralization, sand-slime separation, sand washing, C.C.D., clarification, ion exchange, mine water treatment, and tailings neutralization and pumping will be considered. The application of Enviro-Clear thickeners in the mine water treatment circuit and in the C.C.D. will be briefly reviewed. An automatic grinding and classification circuit for limestone will also be covered. The refurbishing program underway at Panel will be discussed. The Quirke and Panel plants will be contrasted and compared. In particular, reference will be made to environmental considerations. The innovative system for producing yellow cake at Panel, LAMIX, will be considered as well as the proposed treatment system for Panel tailings.

Jan 1, 1979

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

By James R. Wickens, David La Rosa, Robert E. McIvor, Adrian Dance

"The comminution circuit at Barrick Cortez Gold Mine uses an open circuit primary jaw crusher followed by a standard SABC grinding circuit. The grinding circuit incorporates a 26’Ø x 11’ SAG mill, an Omnicone 1560 pebble crusher and a 16’Ø x 28½’ ball mill. Both mills are driven by 4500 HP motors.In 2007, several comminution circuit studies were performed to assess circuit performance and map a course for improvement. This paper discusses the results of those studies including an analysis of mine-to-mill opportunities, grinding work index efficiency, and ball mill functional performance. Subsequently, improvements to the circuit were made to enhance operating efficiency. Specifically, improvements to the pebble crusher liner configuration, advanced process control system (expert system) and ball mill classification and ball charge are discussed. In addition, other current and future improvement opportunities are discussed.INTRODUCTIONThe Barrick Cortez property is expanding to include the new Cortez Hills open pit and underground mines. Ore from these new mines will be processed in the existing Pipeline mill facility. In conjunction with ore characterization work, performance of the comminution circuit needed to be quantified. Thus, in 2007, the comminution circuit was surveyed and opportunities for improvement identified.Figure 1 below shows the Pipeline mill flowsheet. It is a standard SABC grinding circuit using an open circuit primary jaw crusher followed by a 26’Ø x 11’ (7.92m Ø x 3.35m) SAG mill, in closed circuit with a Omnicone 1,560 pebble crusher, and a 16’Ø x 28½’ (4.88m Ø x 8.69m) ball mill. Both mills are driven by 4,500 HP (3,357 kW) motors. The SAG discharge screen aperture is 5/16” (8 mm) x 1-1/16” (27 mm) slots. Ball mill circuit classification is done with Krebs D20B cyclones."

Jan 1, 2009

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002