Search Documents

By C. P. Moore, G. W. Taylor

Vertically dipping lenses of nickel-copper ore at Dumbarton Mines Limited are being mined by a modified blasthole stoping method. The principal access to the mine is provided by a 15-degree decline, which, in conjunction with the use of ramps and declines for secondary access, maximizes the accessibility and mobility of trackless mining equipment. Sublevels are driven in ore on 80-foot vertical intervals and subsequently the ore, ranging in thickness from 15 to 30 feet, is slashed to its limits by a procedure of face sampling and test holing. Two longhole drill jumbos are used to drill off 40-foot vertical slices above and below these levels. Following blasting, the ore falls by gravity to the 500-foot horizon, where it is removed from drawpoints by load-haul-dump units and transported by truck to the main orepass. The rock is crushed to minus 3-4 inches and conveyed to surface by a 30-inch-wide wire rope suspended conveyor. This is achieved in two flights, a lower one of 290 feet and a main flight of 2260 feet. All aspects of the mining operation are discussed in the paper, including ventilation, services and safety.

Jan 1, 1973

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By G. C. Nowlan, A. Illis, H. J. Koehler

At its iron ore recovery plant at Copper Cliff, INCO produces about 17 million pounds per year of a pure, acid-soluble, dense nickel oxide from nickeliferous pyrrhotite. The process used is also applicable to a broad range of ammoniacal nickel-bearing streams. The product has been widely accepted by the chemical, ceramic and electronic industries.

Jan 1, 1970

By A. Koning, P. Lauzon

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature, with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry's experience base. The impact of irreversible chemical swell, operating factors, design factors, and installation factors are presented based on modifications to the traditional one-dimensional mechanical stress model. A new stability criterion - that the brick lining remain in contact with the steel shell membrane - is presented. This new stability criterion imposes new restrictions on the lining design.The effect of geometry and adding additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional Finite Element Analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed.

Jan 1, 2004

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005

By D. A. Beattie

Three novel dextrin polymers of varying functional group chemistry but similar molecular weight have been used to depress talc in single and mixed mineral studies. The mixed mineral system was a model sulphide ore consisting of talc, pentlandite, and chalcopyrite. Adsorption isotherms for the three polymers on both valuable and gangue mineral phases were determined to give initial clues as to the ability of the polymers to depress talc. Flotation testing revealed a distinct hierarchy of effectiveness of the polymers in the depression of talc in the single mineral system (MP Dextrin > CM Dextrin > Dextrin TYM), reflecting the observed adsorption affinity and adsorbed amount of the polymers on talc. However, a different order of effectiveness was observed for talc depression in the mixed mineral system (CM Dextrin > MP Dextrin > Dextrin TYM). Competition between the valuable and gangue mineral phases for uptake of MP Dextrin is responsible for its observed decrease in efficiency in mixed mineral flotation. All three polymers were found to be reasonably selective in their action, although at high dosages the polymers began to affect the flotation of the valuable minerals.

Jan 1, 2006

By J. R. CAMERON

Gypsum is mined in all Atlantic Provinces except Prince Edward Island. It is generally thought to have been derived from the hydration of anhydrite in areas of minimal drainage. Late Devonian downwarping and crustal oscillation east of the Appalachian fold belt allowed the Windsor Sea to advance and retreat in a depositional trough and deposit about 1,000 m of sediments in Mississippian time, much of which were evaporites. The best areas for further gypsum development are lowland basins such as the Cape Breton Lowlands, the Hillsborough area of New Brunswick and the St. George's Lowlands in Newfoundland, all of which are already sites of gypsum quarries. Nova Scotia's gypsum is mined from the Lower Windsor Group, which is divided into subzones 'A' and 'B'; 'B' provides most of the province's gypsum production. The Atlantic Provinces gypsum industry has markets from the St. Lawrence waterway to the mouth of the Mississippi River.

Jan 1, 1984

By N. J. Contini, R. W. Knopp

"In March 1988, old Denver flotation cells were removed from Dickenson's Arthur w. White Mill, and a new flotation circuit, consisting of four Prochem rougher cells and a Hydrochem agitated cleaner column, was commissioned. The refractory portion of the gold in the ore is associated with arsenopyrite, therefore the flotation circuit is set up to produce a saleable sulphide concentrate. Tailings from the leach circuit are conditioned prior to being pumped as feed to the flotation circuit. The prototype Hydrochem agitated column has been in operation as a single cleaner stage for rougher concentrate. The effect of flotation circuit changes on gold recovery data, as well as cleaner concentrate production, and development work to achieve the target results, have been investigated. Flowsheet modifications and the resulting circuit performance data, along with test results to date, will be presented.INTRODUCTIONThe mill is capable of treating 1000 stpd of ore averaging approximately 0.30 oz/ton Au. The ore is crushed and ground to 75% - 200 mesh. Gravity concentration, cyanidation, and Merrill - Crowe precipitation yields 84% gold recovery. Detailed descriptions of the comminution, gravity separation, and leaching circuits, as well as background information have been presented elsewhere (Suttill, Van Weert et al). The target cleaner concentrate grade is 1.0 oz/ton Au for custom smelting and refining. Historical gold recovery values of the old circuit was approximately 20% of the gold present in the float feed at the target grade. The recovery value objective set for the new circuit during the planning stages was 50% of the gold present in the flotation feed at 1.0 oz/ton Au in cleaner concentrate."

Jan 1, 1989

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By D. B. Dreisinger, M. Mokmeli, B. Wassink

Dissemination of selenium and tellurium in sulphide minerals results in the contamination of pregnant leach solutions and electrolytes in the hydrometallurgical treatment of sulphide ores and residues. The selenium and tellurium content of the copper sulphate-sulfuric acid solution may be reduced into insoluble precipitates of copper selenides and tellurides using cuprous ion. This study presents the use of the thermodynamics and kinetics for the removal process of selenium and tellurium in real life application. Dominant species of selenium and tellurium in acidic copper sulfate solutions were identified and the reduction rates of species were compared. The findings were applied to industrial conditions by modeling the Vale’s CRED (Sudbury, Canada) plant’s selenium and tellurium purification circuit. Rate reducing factors on selenium and tellurium removal were identified and discussed.

Jan 1, 2014

By P. E. Weidmark

"PART 1-Published PapersAllcott, G.A., and Archibald, D.E.; ""Description of pillar behaviour at Heath Steele Mines""; Can Min Metall Bull; 74:834:80-87; 1981.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of rock Mechanics; 3:32-33; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:37-38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses"" ; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:41; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:42; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:46; 1979.Baar, C.A.; Discussion of Theme 2: ""Tectonophysics""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:60; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3: 116; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:116-117; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:117; 1979.Baar, C.A. '; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:118-119; 1979.Baar, C.A.; Discussions (2) of Theme 4: ""Underground openings""; Proceedings 3rd Congress lntnl Soc of Rock Mechanics; 3:119; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:120-121; 1979."

Jan 1, 1982

By R. Heikkilä

The utilization of Building Information Modeling (BIM) and model based 3-D control of work machines have increased a lot in new road construction in Finland as well as in other Nordic Countries. Up today, much less attention has been paid into the development of maintenance and rehabilitation processes. As a part of a large research and development program RYM PRE Infra FIN BIM in Finland, a focused research project of the BIM with experiments in total five (5) pilot projects has been performed. A main idea of the new BIM based process has been to utilize mobile laser scanning method for initial data acquirement, the use of novel 3-D analyze and modelling methods for point cloud processing, the use of new type optimization method for the planning of geometric and structural improvements needed for the existing uneven road surfaces, and further, through the creation of 3-D machine control models apply the newest 3- D machine control systems for continuous 3-D control of practical construction work using milling machine and asphalt paver. Finally, an evaluation is made between the new process model and the traditional way of working.

Aug 1, 2013

By John Hansen

This paper has been written for presentation at the 103rd Annual General Meeting of the Canadian Institute of Mining, Metallurgy, and Petroleum, April 29 to May 02, 2000. The paper addresses blast pattern fragmentation and diggability versus the blasting technique used. RESUME The author is the Vice President for Thunderbird Mining Systems. In this capacity he manages the mine site installation of surface mining mobile equipment monitoring and navigation systems. These systems are onboard instrumentation and software systems designed to: ??measure and log mobile equipments? production and health; and ??direct the equipment operators via onboard displays that show comprehensive maps and engineering instructions. The author is a mining engineering graduate from the Royal School of Mines. His work experience includes front line supervisor and mining engineer for Hudson Bay Mining & Smelting, mining engineer for Teck Corporation, and mining consultant for PriceWaterhouseCoopers.

May 1, 2001

By V. Casaletto, L. Widdifield

"Equipment capable of higher production requires more sophisticated maintenance programs. Reduction in fleet size through use of modern technology requires higher utilization and greater availability.Caterpillar's maintenance control system program will display the capabilities of computer technology in a maintenance environment. Utilizing such resources will provide increased availability, lower inventory requirements, fewer last minute disasters, and lower cost per ton for maintenance. High production from premium quality equipment can only be realized by good planning and care, executed by maintenance and operating personnel acting cooperatively.IntroductionAccurate information is the key to accurate decision making. In today' s competitive industry, mines' teeter on the brink between profit and loss. Their survival will be predicated on their ability to retrieve, analyze, and formulate accurate information regarding the operating costs of mobile equipment. This paper deals with the impact of managing equipment operating costs and introduces a computerized control system designed for monitoring and controlling these costs.Caterpillar has produced several computerized modelling programs designed at taking the guesswork out of equipment selection and management. The most basic of these is Equipment Investment Analysis (E.LA.). This model compares two or more alternatives over the projected life of the machine. It deals with comparisons in the owning and operating costs of equipment, as well as, their productivity over a specified period of time.In order for a computer model to be credible as a decision making tool, it must be simple to use and the results measurable and accountable . Caterpillar has introduced several computer models to assist the industry in selecting and managing an equipment fleet. These programs allow the user to predict and monitor the operating costs and production capability of mobile equipment. They are often used in the machine selection process to select equipment which best suits a mine's long-term cost per tonne objectives. After the optimum selection is made, Caterpillar's Maintenance Control System provides an efficient management tool to monitor and verify the data used in the selection model."

Jan 1, 1992

By H. Jung

The microstructures and grain sizes of nanocrystalline Co and Co-1.1 wt % P alloys were characterized by X-ray diffraction. The corrosion properties of as-deposited and annealed Co-l.l wt % P alloys and pure nanocrystalline Co were studied in a deaerated 0.1M H2SO4 solution using electrochemical measurements and XPS surface analysis. Potentiodynamic polarization testing and impedance measurements revealed that an addition of P to pure nanocrystalline Co improved the anodic-corrosion resistance, however, this enhanced corrosion resistance was compromised by the heat treatment process at 350 and 800°C. The corroded surface of annealed nanocrystalline Co-1.1 wt % P at 350°C exhibited a more porous P-enriched layer compared with the as-deposited case. A sample annealed at 800°C corroded uniformly showing second-phase precipitates. The enhanced corrosion resistance of as-deposited nanocrystalline Co-1.1 wt % P was attributed to the elemental P on the surface that acted to hinder the anodic dissolution kinetics of surface Co following an initial selective dissolution of Co. However, at a higher anodic overpotential region, the superior corrosion resistance of Co-l.l wt% P alloys did not last because of the formation of a non-protective surface film consisting of mainly hypophosphite and phosphate as well as elemental P.

Jan 1, 2005

By G. A. Vissac

In this paper we intend to deal particularly with the economic side of coal washing as it applies to our mines. We will then discuss why the dry-cleaning process has been selected, and give a brief description of our plant, dwelling only on its specific features and referring the reader to the numerous papers published on the subject for any details on the principles and machinery used in dry cleaning. ECONOMIC DISCUSSION The washery introduces an extra cost for depreciation, operation, and loss in treatment. A certain proportion of the coal, now being sold, and which the miners have been paid for. will have to be wasted. As a whole, the total increase in cost would be approximately 60 cents per ton. On the possibility of recovering this amount depends the success of the washery. There are two advantages to be expected from the washery, the first, which occurs at the mine and which will be certain; the second, more difficult to estimate, because it depends upon convincing our customers that they should pay more for a better product.

Jan 1, 1924

By A. Khan, C. Ciriello, W. Oliveira

"The purpose of this paper is to demonstrate the value of Operational Readiness (OR) in the successful delivery of capital projects. OR can be captured using several technical and practical definitions:• To ensure that the capital project being delivered is capable of an effective start up, ramp-up as planned and a sustainable productive operation.• To function as intended when started, with the appropriate people able to run it.• To increase the value in delivering the product/service through established systems, processes and procedures, while simultaneously minimize risk to both the project and the business.Historically, mining and metallurgical capital projects concentrate efforts on cost and scheduling during the implementation and design phases. The completion and subsequent handover of the operational unit is the main objective.When reviewing the mining and metallurgical industry’s capital projects, it seems many poor results and errors in terms of project design and ramp-up are self-inflicted, with the project neglecting to account for key aspects of the future operational plant. Interestingly, if the problems for the future plant occur during project implementation, they can be prevented during the project phase. It is required to connect the operational knowledge with the project in order to ensure an effective start up and operation.The benefits of OR will be shown to be applicable not only to mining capital projects but also to sustaining and business transformation projects. The paper also includes industrial examples showing both proper and improper use of OR techniques.The paper will cover 3 main areas of Operational Readiness: the OR model, OR related risk elements (i.e., risks associated specifically with the improper execution of OR) and conclude with OR specific case studies."

Jan 1, 2016

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By Chuan-liu Wang

The bionic non-smooth surface has the characteristics of anti-wear, and reducing resistance. Based on bionic non-smooth surface?s characteristics, a bionic drill bit was developed. When the bionic drill bit is used, a bionic non-smooth surface forms on the crown of bionic drill bit. This surface can be used to extend the life of drill bit and improve drill efficiency. The bionic unit diameter and arrangement were researched in this paper to determine the optimal bionic non-smooth surface for further improving the life and efficiency of drill bit. Four bionic samples having the same structure size, materials and arrangement were designed and manufactured. After being sintered, the abrasion ratios of the four bionic samples were tested, and the results show that the abrasion ratio of Nos. 3 and 2 were similar (only 2% difference) and higher than that of No. 1 and 4. Therefore, the optimal diameter of bionic unit is 1.5 and 2.0 mm. Small diameter bionic drill bits were designed and manufactured, and tested in the laboratory. The results show that not all bionic structure bodies are better than normal diamond bits, except the bionic unit arranged in a reasonable range. When the angle was 24° and 30°, the arrangement of bionic unit were more reasonable, which shows the superiority of the bionic coupling bit.

Aug 1, 2013

By D. C. Rance

"The Quintette Coal Limited property is located in the northeast coal area of British Columbia.A basic agreement with the Japanese steel industry was executed on January 27, 1981 for the sale of 69.5 million tonnes of Quintette metallurgical coal over a 14.5-year period. This contract period can be extended by five years by mutual agreement. Sale agreements have also been signed for the sale of 19.4 million tonnes of oxidized coal over a 15-year period.Work started on site development in the late summer of 1981, and at present, two of the four eventual pits-the McConkey and Frame-are under development.The pits are currently in a prestripping phase. These pits are notable for the stripping volumes that have to be removed from relatively small pit areas. In order to provide for the required detailed rapid short-range planning of these pits, engineering will be computerized, as will the truck dispatch system.The mining area lies 21.1 km from the plant site by road and the transport of raw coal to the plant is by means of a high-speed conveyor system which has a total length of 13.4 km with a vertical drop of 740 m.The surface plant facility was designed on a modularized basis to facilitate maintenance, and is designed to enable the use of gravity f low of raw coal and heavy media in the plant to minimize the use of pumps.The construction of the plant and mine site facilities is ongoing, and the first coal production is scheduled for early December 1983.IntroductionQuintett e Coal Limited is a Canadian company incorporated in the province of British Columbia in 1971. Denison Mine s Limited is the manager of Quintette's activities. Equity in Quintette Coal Limited is held by several shareholders, with interests as follows: Denison Mines Limited, 50%; Charbonnages de France International S.A., 12%; and Japanese interest, 38%."

Jan 1, 1983