Search Documents

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By C. Kim

The integration of three-dimensional (3D) data with infrared thermography has received much attention for its potential use as input data for building energy simulations. Therefore, researchers have proposed methods to integrate 3D data with infrared thermography obtained by different sensors. These studies show the potential of the integration of 3D data and infrared thermography using various systems. However, these studies have ignored property aspects of infrared thermography, such as the low resolution of infrared thermography and external environmental influences. Thus, their proposed methods to integrate 3D data and infrared thermography are inadequate because these problems can affect the resulting building energy simulation. This research proposes a framework that integrates infrared thermography and 3D data while accounting for the resolution and shadow effect of infrared thermography. The proposed framework consists of three steps. In the resolution enhancement step, bi-cubic interpolation is proposed. In thermal data correction from the shadow effect, the shadow area is detected from the visible image, and then the shadow effect is removed from the registered infrared thermography. Finally, enhanced infrared thermography is mapped to the 3D data obtained by a laser scanner. The performance of the proposed framework was evaluated using test images obtained from a building in operation. The experimental results show that the proposed framework provides a 3D thermal model that is useful and accurate in simulating building energy. It is expected that the 3D thermal model can be used for accurate energy simulation of existing buildings. In addition, the proposed framework can be applied in defect detection for buildings. Furthermore, this novel approach enhances infrared thermography using visible images.

Aug 1, 2013

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By M A. Notte

Sand casting of steel is a process that offers the greatest design flexibility and highest metallurgical versatility. However, competition from other methods of fabrication is quite keen, constantly forcing the steel casting industry to the production of better quality castings at lower costs. New methods and materials have been put to use in the last ten years by foundries everywhere. This paper, in the form of a progress report, deals with new methods, processes and materials used by Canadian steel foundries for regular production, as well as with developments still in the initial but promising stages. T HE casting of steel to shape is the most direct method of producing steel parts in their final form. It is a basically economical process both as to cost and production time; it is also a process that offers design engineers the greatest flexibility and highest metallurgical versatility. In North America, the steel casting market has a normal yearly sales volume of 1,500,000 tons. In decreasing order, the largest customers are the railroads, construction machinery and earth-moving

Jan 1, 1965

By J. Mcdvcka

Sustainable development has become a driving imperative for the resource industry as it is for the rest of the global business world. Being unsustainable is a risk no business can afford. Yet implementation of sustainable development practices beyond satisfaction of compulsory reporting is still sporadic. The current standard approaches to problem analysis and decision making are too narrow to capture the complexity of the issues at stake. Hence it is necessary to develop innovation in thinking and in doing. Those who search for ways to implement sustainable development use concepts such as Whole Systems Thinking and Eco-efficiency as well as tools like Life Cycle Analysis. Others develop their own instruments. In their effort to innovate they face both resistance and support within their organisation as well as within the industry or the wider context. This paper explores the factors that support, hinder and shape the sustainable development drive of the industry and proposes a comprehensive decision-making framework that links the goal of sustainability with the tools of sustainable development. This exploration is illustrated by a case study used in a doctoral research conducted on an engineering firm providing services to our industry.

Jan 1, 2007

By I. Lackey

In 2004, Zinifex Budel Zink commenced testing with the objective to increase the precipitation of aluminium in the iron purification stage of its hydrometallurgical zinc circuit, without the use of expensive reagents. Findings from the literature applied to the leach circuit at Zinifex Budel Zink demonstrated that aluminium removal from the leach circuit could be increased by lowering the ferric concentration and acidity in the vessels where jarosite precipitation occurs. An associated increase in copper precipitation was mitigated by limiting the extent to which the ferric concentration was lowered in the vessels where jarosite forms and lowering the ratio of copper to aluminium in the solutions entering these vessels.

Jan 1, 2006

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By R. J. Young, S. J. Tennant, A. D. Drummond

"Gibraltar Mines is located on the western slope of Granite Mountain, 230 air miles north of Vancouver, B.C. and 38 miles north of Williams Lake, B.C. There are four mineable zones within the copper-molybdenite deposit: Gibraltar East, Gibraltar West, Pollyanna and Granite Lake. Open-pit reserves are 358 million tons which average 0.37% Cu and 0.016% MoS2 at a 0.25% Cu cut-off. The Granite Mountain pluton is one of the several Jurassic-Cretaceous intrusions which outcrop along the east side of the Fraser River fault system between Williams Lake and Prince George, B.C. The original Granite Mountain quartz diorite has been metamorphosed by a cataclastic deformation which foliated the rock on a regional scale. Attendant to the development of the foliation, the rock was saussuritized such that the present mineralogy is compatible with that of the greenschist facies. The presence of garnet-bearing assemblages is explained by a restricted increase in water pressure. Pre-mineral intrusive phases within the saussuritized quartz diorite are: (1) leucocratic quartz diorite, (2) aplite and (3) quartz-feldspar porphyry. A late chloritized hornblende dacite dyke is post-mineral. Quartz-feldspar porphyry and leucocratic quartz diorite are locally present on the inner sides of the Gibraltar East, Pollyanna and Granite Lake pits. Their presence suggests a core around which occurs an elliptically shaped sulphide-bearing stockwork. The stockwork, which comprises four ages of vein development, is imposed on and partly controlled by the regional foliation of the samssuritized quartz diorite."

Jan 1, 1973

By C. Allen

In 2004, Boliden Odda underwent an extensive modernisation project targeting mainly the leaching section of the plant. Direct leach technology was introduced as part of this project. The Direct Leach process, developed by Outokumpu, is an atmospheric oxidative leach of zinc sulphide concentrate. The effects of this new processing operation on behaviour of iron in the plant are discussed. As well, the filterability of the new residue on belt filters prior to its deposition in mountain caverns is also discussed. The solids from the direct leach process have been analysed by scanning electron microscopy, and the results of these analyses are presented.

Jan 1, 2006

By R L. Cheesman

An extensive Precambrian iron-formation lies about 2,000 ft. beneath post-Precambrian rocks in the Fort a Ia Corne Forest Reserve, south of Choiceland, Saskatchewan. The geology, deduced from limited drill results and from some geophysical observations, indicates that the deposit is a characteristic magnetite iron-formation, not uncommon in the exposed Precambrian of Saskatchewan, but also shows certain interesting features of faulting and pre-Paleozoic weathering which have given rise to a pre-served detrital deposit of hematite. The body is of ore grade and of sizeable proportions. T HIS paper is presented in order to set forth the interesting geological features of a Precambrian iron deposit located beneath the cover rocks of the Great Plains region and to comment upon the methods of discovery and interpretation of the nature of the body. The Choiceland iron deposit is located in the Fort a Ia Corne Provincial Forest Reserve, some 15 miles south of the town of Choiceland, Saskatchewan. Choiceland is

Jan 1, 1964

By R. R. Irrinki

Abstract -The Key Anacon deposit consists of four sulfide zones called, from south to north : Key Anacon No. 1, Key Anacon No. 2, Key Anacon No. 3, and Key Anacon Copper Zone. Massive sulfides of zones 1, 2, and 3 are underlain by rocks correlated with the Nepisiguit Falls Formation and are overlain by matie volcanic rocks correlative with the Boucher Brook Formation. In contrast to zones 1, 2, and 3, narrow northwesterly-trend.ing, copper-rich fracture zones occur within the Patrick Brook Formation. Sulfides in zone 2 occur as three mineralogical associations, namely: pyrite-chalcopyrite, pyrite-sphalerite-galerta, and pyrrhotite-sphalerite-galerta. The distribution of lithologies and en-echelon patterns of the three sulfide lenses of Key Anacon No. 2 zone are the result of F1 and F2 folding. Zone 2 is the most promising economically, with proven reserves of 1.11 million tonnes grading 0.2207o Cu, 3.47% Pb, 8.41% Zn, and 96 g/t Ag; the zone is open below a depth of 427 m.

Jan 1, 1992

By O. Schnake, M. Isakson, C. A. Landolt

The paper presents the conceptual basis for the development of an Activity Based Costing system (ABC) for the analysis and estimation of process costs in mining and metallurgy. In particular, it discusses three major thrusts towards attaining increased efficiency in extraction and processing systems: (a) understanding the link between process and expenses, (b) identifying the chemical and physical factors that govern process costs and ( c) using process and cost models of the production systems. The authors have developed computer techniques to analyze data from conventional accounting and apply them to the development of process based ABC systems. The cost causing activities are linked to management units patterned after the organizational structure of the production system. All costs are associated with specific process functions such as charge preparation, smelting, refining, etc. The level of detail is determined by the quality of data available in conventional accounting systems. The system permits data analysis of historical cases and the projection of costs for new production schemes. Results can be presented in various levels of aggregation, following organizational and/or functional structures. The outputs of the system are tabular and graphical, typically following Pareto analysis concepts.

Jan 1, 2007

By W. E. Cockfield

This paper is not intended as an original contribution to this subject, but rather as a review of the main theories which are held with regard to placer deposits, with, of course, particular reference to the placers of British Columbia. The present interest in gold mining has, however, brought the subject of placers to the fore, and possibly a brief outline of the geology of such deposits will serve as a basis for discussion on the subject. In Canada, the most valuable of our placers are deposits of gold, and consequently the discussion will centre largely on placer-gold deposits. The same principles apply, of course, to placer deposits of other metals. The Origin of Placer Deposits As a starting point, the idea which is prevailingly held is that placer or alluvial gold is detrital in origin, that is to say, the gold originally existed in veins, lodes, or disseminations in the country rock of the regions in which the placer deposits are now found, and that, through the various erosive forces of nature, it was liberated from those veins or lodes and concentrated in the form in which we now find it. 1 have not time to go thoroughly into the proof of this, but the lines of evidence are many. If we take the Cariboo district as a typical example, Johnston and Uglow(l) have shown, first of all, that the placer and vein gold are identical in character. Crystals occur both in the placers and in the lodes, but the crystals in the placers are nearly always slightly worn, indicating transportation.

Jan 1, 1932

By Curtin University Western Australian School Mines

"Curtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc.) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The model structure, modelling approach, and some scenarios are discussed.INTRODUCTIONCurtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. The model has recently been upgraded to include an integrated liberation-leach modelling (ILLM) approach. The ILLM approach provides the means to evaluate the impact of the gravity recoverable gold (GRG) characteristics of the ore (GRG content and liberation behaviour), various process parameters (such as grind size, bleed to gravity, etc.) and circuit configurations on the gravity gold recovery, leachadsorption circuit behaviour and overall plant gold recovery.A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach. The data required for the ILLM calibration can be obtained directly from the 3 stage GRG test, leach tests and size-by-assay analysis of the 3 stage GRG test products, and leach test products.This paper describes the ore characterisation methodology, model structure, modelling approach, and the application of the ILLM."

Jan 1, 2016

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013

By C. O. Aksoy, H. Kose, K. Ozfirat, T. Malli, A. Gonen, S. Gurgen

In selecting mobile mining equipment, factors including availability, useful economic life, maintenance and operating costs, and spare parts availability are considered. Given these factors, trucks and shovels with different capacities are selected. Optimizing equipment for pit and hillside quarry cases, where 8% and 10% ramps are commonly in use, were examined; the effect of other mining activities such as drilling and blasting on unit cost were considered. In principle, 20 m to 25 m high benches should be economical for downhill haulage, and 7 m to 10 m low benches economical for uphill haulage. However, practice of both mining styles favours 10 m to 15 m bench heights. Hence, the analysis here was carried out with the field experience bench height range. In the study, a truck-shovel optimization was based on the movement of 5 to 20 million cubic metres (in 2.5 million cubic metre increments) of overburden stripping at the Eynez open pit mine in the Soma region of Turkey. The outcome showed that low-capacity shovels were unfavourable due to high production expectations. High-capacity shovels were also unfavourable due to health and safety issues causing high instances of impact vibration on trucks during the loading cycle and a decrease in foreseeable unit lifetimes. The number of shovel passes required to load a truck ranged from three to six. Trucks with high-capacity bodies were deemed uneconomical due to high investment and operating costs.

Jan 1, 2005

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968

By M. J. MONEA

Canada's only economic high-swelling bentonite deposit is mined in Wilcox, Saskatchewan, by A vonlea Mineral Industries Limited. The bentonite resulted from devitrified and altered volcanic ash released during the Laramide Orogeny. Volcanic ash was deposited in a pre-Cretaceous basin that was formed by salt solution collapse structures. Sedimentary rocks in the Wilcox area belong to the Snakebite Member of the Upper Cretaceous Bearpaw Formation. Bentonite beds are 61 cm, 46 cm and 30 cm thick; these are separated by 365 cm and 182 cm of shale respectively. Saskatchewan bentonite is used primarily in the oil well industry.

Jan 1, 1984