Search Documents

"Canada Centre for Mineral and Energy Technology (CANMET)Natural Resources CanadaMining and Mineral Sciences LaboratoriesA. Address and Contact Information555 Booth StreetOttawa, Ontario, Canada, KIA OGlWebsite: http://www.nrcan.gc.ca/Contact: Philippe Dauphin, Manager, Business DevelopmentTel.: (613) 947-0798Fax: (613) 947-0984E-mail: pdauphin@NRCan.gc.caB. Type and Size of FacilityScope of facilitiesCrushing from minus 4 in. to 10 mesh; grinding - rod, ball, vibration, SAG and impact mills; classification- screening, cycloning, mechanical, hydraulic and dry centrifugal classifiers; froth flotation - automated, column, and frothless flotation; gravity separation- wet and dry; magnetic separation - high gradient, high and low intensity, wet and dry; electrostatic separation; heavy-media separation; calcining; cyanidation; thickening; filtration; drying - fluid bed and freeze drying; pelletizing; microwave.SpecialtiesMineral beneficiation research and development; flotation of sulphides - flowsheet improvement, selectivity, reagent selection; novel flotation techniques; analysis of thiosalts formation; use of mineral processing techniques for recycling.Specialized equipmentHigh gradient magnetic separation, Denver XRF on-stream analyzer, automated flotation cell.Complementary support servicesElectron microprobe; SEM; STEM; X-ray diffraction; particle size analyzer; mineralogical and analytical chemistry services; physical chemistry; hydrometallurgy; pyrometallurgy; engineering and economic evaluation; mechanical shops; technical information services and library integrated with the National Library System of the National Research Council."

Jan 1, 2000

By A. Bauer

This paper describes the trends in recent years in explosives formulated to produce larger blast-hole spacings and over-all lower drilling and blasting costs in hard formations. A consideration of current rotary drilling costs per ft of hole and per ton of muck versus hole diameter indicates that it is now possible that we shall see much further use of lower-energy-content, lower-cost slurries and dry mixes, and larger-diameter and, in many instances, cheaper blast holes. These will be drilled on current or slightly larger blast patterns to yield the same energy input per ton of rock and similar fragmentation at lower costs.

Jan 1, 1968

By S. Kivrak

The firms in construction industry could not sufficiently adapt the rapidly emerging information technologies in recent years into their corporate structures. Therefore, in an effort to further exploit the benefits of information technology (IT), integration of the experiences and backgrounds of construction industry and the advantages of IT, is one of the most open-ended fields for improvement in this industry. Utilization of IT in the construction sites will positively affect the efficiency, productivity, quality and health & safety issues in the construction sites thus the cost and completion time of the projects. Within this context, augmented reality technology, which brings a new perspective into IT, can be put into the service of construction industry. Augmented reality which has been designed to improve the services in many application domains such as school education, military warfare, military trainings, industrial maintenance, retail and medical, can be defined in the simplest form as augmenting the real world with information from the virtual world. The main aim of this study, which presents an overview of an ongoing project, is to develop an innovative method by making a construction worker, foreman, equipment operator or a site engineer watch a very comprehensive and informative animation which will enable the said staff to perform or supervise all the phases of the activity he or she is in charge for in a more efficient, productive, safer and qualified manner by means of smart glasses using augmented reality systems. In this respect, training material related with the activities in the construction sites will be prepared and with a well-fictionalized scenario, animations exhibiting all the phases and details regarding the related activity (e.g. masonry, formwork and rebar works etc.), method of statement, correct and incorrect applications in comparison-wise manner, will be produced. Therefore, the user will be able to reach the training material, method statements etc. in the animations about the activity he or she is in charge for, enabling him or her to figure out the work as prescribed in the specifications. Basic trainings about the system will be given to target group, i.e. construction workers, foremen, operators, site engineers and managers working in the construction sites to apply the system on sites after all the system was tested. After the testings, to determine the effectiveness of this system, semi-structured interviews and survey questionnaires will be conducted among the mentioned target group. Therefore, the potential benefits of this system to the construction industry can be determined. The main target of this study is to implement an efficient, thorough construction management by orienting the staff in the construction sites to perform efficient, safe and qualified works by means of smart glasses that use augmented reality. There are relatively few studies about the implementations of augmented reality technology in construction. The outputs to be attained in the end of the study have the potential of improvement of time, cost, quality and safety parameters by ensuring a qualified, safe, efficient and productive construction management via augmented reality technology in the construction industry.

Aug 1, 2013

By W. A. MacDonald, C. M. McGibbon, J. H. Reynolds

This paper traces the development of the Seaboard Power Plant, which plays such an important role in the industrial life of Nova Scotia. It also shows the involvement of the plant in the siting of a heavy water production facility in Cape Breton. The paper concludes with an outline of the new installations which the Nova Scotia Power Commission has undertaken as an extension to the Seaboard Plant.

Jan 1, 1966

By B. K. Mishra, Subrat Kumar Padhy, B. C. Tripathy, I. N. Bhattacharya

Manganese is a difficult metal to electrodeposit due to its high electronegativity and continues to possess unique process challenges. Manganese deposits of high quality are electrodeposited on 316 grade stainless steel from sulphate solutions in the presence of organic additives such as tetra ethyl ammonium bromide (TEABr), tetra propyl ammonium bromide (TPABr), and tetra butyl ammonium bromide (TBABr). The concentrations of these additives were examined over a relatively broad range to evaluate their effect on current efficiency, specific energy consumption and deposit morphology of the electrodeposited manganese metal. A maximum current efficiency of 68% was achieved in the presence of TEABr in the bath. X- ray diffraction studies revealed that (330) (411) planes were the most preferred planes of crystal growth during manganese electrowinning at a current density of 500 A/m2 resembling alpha-manganese irrespective of the nature of additive. Scanning electron micrographs showed smooth and uniform deposit morphologies when manganese was electrodeposited in the presence of TEABr.

Jan 1, 2014

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By Étienne Yvenou, Martin Désilets

Le procédé d’électroaffinage du Cu est nécessaire pour atteindre les niveaux de pureté requis pour les applications les plus courantes telles que son utilisation comme conducteur électrique ou thermique.

May 2, 2024

By J. P. Wiser

THIS paper discusses testing and quality control of milled asbestos fibre. It has been composed with the intention of: (I) Summarizing past, present and probable future methods of testing and classifying the various grades of commercial asbestos produced by the Quebec asbestos industry. (2) Acquainting those unfamiliar with the methods used for evaluating, testing and controlling the grading and the quality of Quebec chrysotile asbestos fibres with some of the physical and chemical procedures currently used for that purpose. (3) Discussing some of the complications facing the producers, such as variations in the orebody and special requirements of asbestos manufacturers. ( 4) Detailing some of the present quality control methods. SUMMARY OF PAST, PRESENT AND PROBABLE FUTURE TESTING METHODS Past During the first years of production of commercial asbestos in the Province of Quebec, fibre testing and quality control were based principally on dry screen analysis and visual inspection. These methods were gradually expanded during the period from 18, 90 to 1932. In 1932, standardization

Jan 1, 1962

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By J. C. Rudolph

"THE TOPIC on which I am speaking this afternoon is ""The Future of the Canadian Oil Industry.'' At the time of C + 100, we should take a searching look at ourselves, an honest appraisal of our achievements and a forthright accounting of our shortcomings as well as the uniquely Canadian aspects of this industry. I would like to put before you some of my views on the direction we are taking in the exploration field and in the production field. I would also like to speak briefly on some of our problems and the role of the various segments of our industry in solving these problems.First of all, let us look at the exploration picture. We are in the midst of an exploration boom. There were 133 seismic crews active in Western Canada this winter, the highest since 1957, land prices are appreciating rapidly, Canadian oil reserves increased + 16 per cent during 1966, there is a great demand for technical personnel of every kind and the whole industry, except the drilling segment, seems to be prospering. This surge of activity has its roots in two major occurrences. The first of these was the change in the pro-ration system in Alberta, the major producing province, accompanied by the change in spacing pat-terns. The proration change was designed primarily to encourage in-creased exploration and it has certainly had this effect. It has also had the unforeseen effect of put-ting everyone into what we, in the oil business, call ""elephant hunting."" In other words, the days of the development of barely economic, marginal fields are over. Oil companies today are only interested in high-reserve, high-productivity, high-quality reservoirs."

Jan 1, 1968

By J. T. Fyles, C. G. Hewlett

"THE REEVES MACDONALD mine is in the Sa Imo-Pend d'Oreille mining area of southeastern British Columbia. It is on the Nelway-Waneta road 4 miles west of the border-crossing point of Nelway. The Reeves orebody from which all production has come is one of several mineralized zones in easterly-striking limestones occurring between the Pend d'Oreille and the lower part of Salmo River.The property was originally located as two groups of claims by R. M, Reeves and J. H. McDonald. The two groups were consolidated in 1925. and extensive development work was done from then until 1930 and again in 1937, but no ore was shipped. The mine was reopened in 1947 and, between 1949 and 1953, 1,057,804 tons of ore was mined. Concentrates recovered contained 85,626 ounces of silver, 19,394,092 pounds of lead, 72,076,495 pounds of zinc, and 455,051 pounds of cadmium. Low metal prices forced the mine to close in 1953, but operations were resumed in November, 1955.The orebodies at the Reeves MacDonald mine are steeply plunging lead and zinc sulphide replacement deposits in a banded limestone named the Reeves limestone. The orebodies contain pyrite, honey-coloured sphalerite, and galena, and are surrounded by a dolomitized zone. In the Reeves orebody, where the relationships are known, the dolomite has the same general shape as the orebody. Four zones of sulphides are known on the property (see Figure 1). Three of these, the Reeves, B. L., and O'Donnell, are believed to be faulted segments of one mineralized zone. The fourth, the Point ore zone, exposed on the north bank of the Pend d'Oreille River, is not developed and its structural position is not known, but it appears to be a separate deposit."

Jan 1, 1949

By H. D. S. Miller

"Artificial stope support has become an essential component of many underground mining operations. Because the use of cable bolts in open stopes is a relatively new concept, most support is still designed by trial and error or by rules of thumb. This often results in costly overdesigned support or inadequate support which leads to stope failure.This paper proposes guidelines to determine support requirements using the stability graph method. The stability graph method is an empirical open stope design technique that takes into account the key factors that influence stope stability. The factors for the design of a cable bolt support system include bolt length, bolt intensity and the original rock mass competency and can be estimated using empirically calibrated charts. The empirical charts were developed based on more than 60 case histories of cable bolting success and failure in Canadian open Slope mines.The concept of pre reinforcement and supp ort stiffness will also be discussed.INTRODUCTIONArtificial support, in the form of rock anchors, has become an important component of all underground mining operations because its stabilizing effect contributes to make underground workings safer. There are several types of rock anchors featuring different properties and having a variety of functions. This paper focusses on grouted cable bolt applications in large open stope mining. Such a support system may improve the competency of the disturbed rock mass to a point approaching the undisturbed rock quality by limiting joint movement and dilation. This results in more stable, possibly larger and, thus, more efficient production stopes."

Jan 1, 1989

By A. M. Cameron

THE HOISTING PLANT at the Stobie section of the FroodStobie mine is a two-shaft installation designed to handle a daily production of 18,000 tons of ore at depth. The two vertical shafts are within 100 feet of -each other, an arrangement made to provide the needed capacity and to give flexibility of operation (Figure 1). No. 7 shaft, used for handling men and supplies as well as for hoisting ore, has been sunk to the 3000 level and is served by a manhoist handling two cages and an orehoist with two 14-ton capacity Kimberley skips. No. 8 shaft, so far completed to a depth of 1,900 feet, handles only ore. The hoist is semiautomatic with push-button control and the skips are 15-ton capacity bottom-dump. The ore-loading pocket for first stage hoisting at both shafts is 120 feet below 1,600 lev-el and additional pockets are planned, as the shafts are deepened, at 800 foot intervals down to 4,000 feet.

Jan 1, 1956

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By Arthur Laing

"IT is indeed a pleasure to have the opportunity of addressing this group today. Not only does it give me the opportunity of meeting with representatives of what is considered by many to be the most dynamic segment of industry in Canada today, but it also allows me to talk about a subject of para-mount interest to myself, the development of the North, and to explain, if even only briefly, some of our beliefs and hopes in this regard.It is inconceivable that all lands north of the 60th parallel, representing 35 per cent of Canada's total land area, which we believe contain a great natural resource potential, will remain as an undeveloped portion of Canada. The re-sources are there, although the people and private industry are as yet not there in sufficient numbers.It has been estimated that in the west and north of Canada there are 1.6 million cubic miles of sedimentary rocks. Of this figure, 342,-000 are thought to lie in Alberta, 115,000 in British Columbia and about 1 million cubic miles are thought to lie in Canada's northern regions, the bulk in the Arctic Islands. On the basis of apparent volumes of sedimentary rock, we estimate that as much as 13 billion barrels of petroleum may lie beneath the permafrost of the North-west Territories, another 3 billion barrels in the Yukon Territory and 33 billion barrels in the Arctic Islands. This is, indeed, a rich and elusive prize, and one which must be sought with a view to fulfilling demands on the production of petroleum."

Jan 1, 1966

By A. Todd Davis

"Introduction“CAN YQUR Company afford not to train?"" This question was asked by Jack Taylor in the Factory Management Magazine for June, 1950. Mr. Taylor went on to say, ""No, it can't; no Company can"". It's true that many training programmes have not done the job they were designed to do because of a number of factors such as parts of management resenting training, management failing to understand the abstract values of training, and management giving impossible assignments or picking the wrong trainers. However, Mr. Taylor summarizes his article by saying that a properly-designed and •conducted training programme brings a company or a corporation to the point where the question is: ""Can my Company afford not to train?""About two years ago, in July, 1952, Nevada Mines Division of the Kennecott Copper Corporation embarked on a training programme, the same type of programme that had been inaugurated earlier at the •Utah Copper Division at Bingham, Magna, and Garfield, Utah. President Charles Cox of Kennecott, in •a speech made •before the Utah Bankers Association in June of 1951, stated that, ""I think that our programme of employee training is one of the most important phases of our entire operation"". That statement might be said to be one of the guiding principles of training at Nevada Mines Division. Training is supported by top managements and down the line to Division managements. As the years go by, the Company expects to receive many benefits from training."

Jan 1, 1954

By C. Ayora

The Iberian Pyrite Belt (SW Spain and Portugal) contains one of the largest reserves of pyrite in the world with mining activities dating back to prehistoric times. About one hundred abandoned mine wastes and galleries release a huge acidity and metal load to the Tinto and Odiel rivers. Once the mining activity is over, polluting discharges can persists for decades or even centuries with no specific responsible entity. In-situ passive remediation technologies are especially suitable for these orphan sites. The concept is to insert a reactive porous material in the natural flow path of contaminated surface and ground waters, and it is implemented through infiltration ponds and reactive barriers, respectively. Calcium carbonate pea-size gravel is the common alkalinity supplier to neutralize acidity and precipitate metals. These remediation systems have been traditionally implemented in coal mines. However, the acid drainages from the Iberian Pyrite Belt contain metal concentrations one to two orders of magnitude higher than those from coal mines and require special designs to avoid quick clogging or passivation (coating) of the grains of reactive material. To overcome these problems, a Dispersed Alkaline Substrate (DAS) mixed from fine-grained limestone sand and a coarse inert matrix (e.g. wood chips) was developed. The small grains provide a large reactive surface and dissolve almost completely before the growing layer of precipitates passivates the substrate. The high porosity and the dispersion of nuclei for precipitation on the inert surfaces retard clogging. However, limestone dissolution only raises pH to values around 6.5, which is sufficient to precipitate the hydroxides of trivalent metals (Al, Fe), but it is not alkaline enough to remove divalent metals. Magnesium oxide, which hydrates to Mg hydroxide upon contact with water, buffers the solution pH between 8.5 and 10. A DAS system replacing limestone with caustic magnesium oxide has been tested to be very efficient to remove divalent metals (Zn, Cd, Mn, Cu, Co, Ni, Pb) from drainage previously treated with limestone.

Aug 1, 2013

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By M. J. King, D. A. Van den berg, R. Fukuzawa

"Mercury bearing ore bodies are often treated for the production of copper, lead, zinc, gold, and silver. The mercury deports either to tailings or is collected during various stages of the extraction process. This paper reviews the relationship between various mercury collection processes and the subsequent management of the mercury by-product or waste. It focuses on mercury removal sequestration including cementation, sulphide precipitation, bulk neutralization, and carbon adsorption. Long term mercury management strategies including third-party stabilization, stabilized mercury co-disposal, secure storage, and mercury recycle are also evaluated. INTRODUCTIONMercury is produced in North America as a by-product of non-ferrous metals processing and from recycling of products such as dental amalgam, fluorescent lamps, and thermometers. Its toxicity is recognized to have significant negative impacts on the environment and human health. As a result, many countries are adopting regulations limiting mercury use and its uncontrolled release.The European Union banned mercury exports in 2011 and the United States will do so in 2013. The export bans aim to prevent mercury use in developing countries for activities such as artisanal small scale gold mining. However, by-product mercury production from the non-ferrous metals industries continues.These factors contribute to an oversupply of mercury and the need to find suitable treatment methods for the long term management and storage of mercury and mercury bearing materials."

Jan 1, 2012