Search Documents

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

By Pan Zhao, Yan-Nan Wang, Fei-Long Liao, Can Cai, Kai-Song Wu

"What are the basic physical parameters and main geometric parameters that are capable of representing the microscopic characteristics of rock? How can these parameters be used to accurately describe the macroscopic mechanical behavior of rock? With such questions in view, and based on the microcosmic structure analysis of rock slices, this paper presents a rock skeleton-pore structure model, holding that rock's mechanical behavior depends on the properties of rock skeleton materials and the form, size and distribution pattern of pores. According to rock stress and deformation behaviors, and in line with the skeleton-pore structure model, an essential mechanics theory for rock is advanced. The assumption that the skeleton materials are incompressible in volume and an introduction of logarithmic strain, generate the relation between porosity and apparent strain. Then, the notion that positive damage and negative damage are represented in terms of porosity is put forward; threshold value of porosity is derived by the damage threshold value of apparent volume strain; a general damage variable of rock is obtained; eventually, with the skeleton-pore model as the groundwork, a global damage constitutive equation is developed, which, with definite physical significance and material parameters to be easily determined, is convenient to apply. It has been proved that the results calculated with this new equation are well in agreement with experimental results.INTRODUCTIONRock is a form of material that contains pores, cracks and skeletons. Skeletons are composed of particles and cements. Pores or cracks within rock actually undermine the assumption of material continuum in solid mechanics. Hence, grave errors — or even false results — are inevitable if some solid mechanics theory is quoted in the discussion of rock mechanics. Many researchers in the field of rock mechanics have attempted various remedies, but the outcome is far from satisfactory — a mechanics theory for rock, in its true sense, has not been established."

Jan 1, 2015

By Ali Montaser

Hauling trucks are important part of equipment fleets for large earthmoving operations such as those encountered in dams and highway construction projects. This paper presents an automated methodology for tracking and estimating productivity of hauling trucks fleet operations in near-real-time. Recent advancement in automated site data acquisition technologies made their use in tracking and monitoring of construction operations feasible. However, these technologies fail to track hauling truck fleets due to the change in the cut and fill locations from one cycle to another; making tracking and progress reporting difficult and inaccurate. In addition, there is very little work done utilizing data sensed directly from equipment, for example sensing when truck dumping bed is raised during the dumping process. The technologies deployed in the developed method are Radio Frequency Identification (RFID) and equipment control sensors. Low cost passive RFID tags are attached to hauling trucks and fixed RFID readers are attached to loaders or excavators. The read range of the used RFID tag is centimeters, to be activated only when a loader with an attached RFID reader is loading a truck. On the other hand, control sensor is connected to the truck control system and operated by the motion of its movable bed. The function of control sensors is to record the signal time when the truck operator gives order to the truck control system to raise or lower truck bed. The captured data is then transferred wirelessly from the RFID reader and control sensor to a computer housed in one of the temporary offices onsite and subsequently to the main server in the contractor?s head office. Fusing the data captured from RFID reader and control sensor is used to identify loading, travel, dumping and return time that constitute the hauling truck cycle time. The collected data is analyzed and processed automatically, without human intervention, to calculate the productivity of the hauling truck and to report it directly to onsite personnel. Relational database is developed to support the implementation of the proposed method. The developed database is used to process the data captured by the RFID and the control sensor to calculate the productivity achieved in cutfill operations in near-real-time. The developed methodology is expected to facilitate early detection of discrepancies between actual and planned performances.

Aug 1, 2013

By K. Harris, J. B. Wahl

Ni-base superalloy cast materials provide an outstanding balance of high temperature strength, fatigue resistance, oxidation resistance and coating performance and can be produced to very tight tolerances in extremely complex configurations, such as axial and centrifugal integral cast turbine wheels. As a result, cast superalloys are used in the most demanding applications of aero and industrial gas turbine engines. Use of these materials is expanding to smaller microturbine, turbojet, turbocharger and missile engine applications due to this unique combination of desirable properties. This paper will present an overview of the application of investment cast Ni-base superalloys and process capability to small turbine and missile engines.

Jan 1, 2010

By Ye Chen, Jianhua Chen, Xianhao Long, Qingxia Liu, Zhenghe Xu

"It is crucial to understand the mechanism of the collector interacting with the mineral surface in the presence of water molecules, which could influence the relaxation and electronic properties of sulphide mineral surface due to the proximity effect for narrow band gap of semiconductors. The adsorptions of three typical collector molecules (xanthate, dithiocarbamate and dithiophosphate) on the sulphide mineral surfaces in the absence and presence of water molecule have been simulated by density-functional theory (DFT). The calculated results show that the adsorptions of collectors on clean mineral surface in vacuum are not in agreement with the observed flotation behaviours. The presence of water molecules has a great influence on the adsorption of collectors. The analysis of density of states of the mineral surface atom suggests that the adsorption of water molecules could influence the electronic properties of mineral surface and consequently influence the adsorption between the surface and the collector molecule.INTRODUCTIONIn the separation of multi-metal sulphide ores, the selectivity of a collector is a key factor for the efficient recovery of the aimed mineral. Xanthate, dithiocarbamate (DTC) and dithiophosphate (DTP) are the most common collectors used in the flotation of sulfide minerals. Generally, xanthate exhibits powerful collecting property but lack of selectivity. While dithiophosphate and dithiocarbamate show the good selectivity in the lead and copper sulphide mineral flotation. The mechanisms of these collectors interacting with the sulphide mineral had been attracted many attentions and several mechanism based on experimental results had been reported (Chander & Fuerstenau, 1974; Fuerstenau, 1990; Raju & Forsling, 1991; Crozier, 1991; Bradshaw, Cruywagen & O’Connor, 1995; Guler, Hicyilmaz, Gokagac & Emekci, 2006). However, the micro-mechanisms of the selectivity of these three thiol collectors on different sulphide mineral surfaces are not fully understood."

Jan 1, 2016

By Ann Bigué

Outline of Presentation 1. Impacts and Benefits Agreements Defined 2. Elements that determine the content of an IBA: ? the nature of the project ? the identity of Aboriginal communities affected by the project ? the legal environment 3. Content of Impacts and Benefits Agreements Impacts and Benefits Agreements Defined Have emerged in response to effects of major mining projects located on or close to Aboriginal lands and close to Aboriginal communities Are negotiated between the mining project proponent and one or more Aboriginal groups May include government May be known under other names

May 1, 2004

By O. K. Mahabadi, A. Lisjak, B. S. A. Tatone, N. Vlachopoulos

"Numerical simulations are widely adopted in the design of several types of rock structures, including tunnels, caverns, rock cuts, and open pit and underground mines. In recent years, analyses based on the hybrid finite-discrete element method (FDEM) have been shown to provide a realistic representation of rock mass deformation and fracturing processes. To date, the FDEM approach has successfully yielded qualitative and quantitative results for several practical rock engineering applications, yet it has lacked the ability to consider the implementation of rock-reinforcement measures. Since rock reinforcement is often used in civil and mining applications to improve the strength and deformational behaviour of a rock mass, the ability to incorporate such features into FDEM analyses is essential to extend its applicability to a broader range of problems. The work presented in this paper represents an important first step towards developing a simulation tool that can be used for practical rock engineering applications, including the design of underground excavations and rock slopes.INTRODUCTIONRock support and reinforcement measures are often employed in civil and mining rock engineering projects in order to maintain or improve the strength and deformational behaviour of rock masses. The preferred type of reinforcement or support elements along with the preferred layout and timing of installation depend on the in-situ ground conditions, the nature of the rock mass and excavation method. Over the last two decades, numerical modelling has been increasingly used to design and attempt to optimize rock reinforcement and support systems. As such, most rock engineering-specific modelling software now offers various approaches for modelling different rock reinforcement and support elements."

Jan 1, 2015

By Harold L. Gibson, David H. Watkinson

"Volcanogenic massive sulphide deposits of the Noranda Camp cur throughout the Noranda Shield Volcano but are concentrated and along the margins of the Noranda Cauldron. The deposits are realized along synvolcanic faults that also accommodated subsince and controlled the location of eruptive centres. Deposits within e 3 000 m thick Mine Sequence formed during a period of active volcanism and subsidence coinciding with the onset of two cauldron subsidence cycles. The Noranda Cauldron was a restricted site of 10malously high heat flow and structural permeability that favoured e development of a high-temperature hydrothermal system. Metals may have been derived from leaching of aquifer rocks by convecting a water or directly from a shallow underlying magma chamber, now presented by the Plavrian Pluton, that was at its highest position !thin the crust during cauldron subsidence. The deposits formed rough a combination of sulphide precipitation from exhaled fluid td replacement at and below the seafloor in a manner analogous to ose on the modern seafloor.RESUMESi les dépôts de sulfures massifs volcano gènes du camp minier de ~uyn-Noranda sont présents dans les différentes parties du volcanluclier de Noranda, ils se trouvent concentres toutefois, en plus ·and nombre, sur le pourtour de la caldeira (cauldron) de Noranda. ~s dépôts sont localises le long des failles synvolcaniques qui ont cilite la subsidence et contrôle la position des centres d’éruption.~dépôts situes dans la séquence des mines (3 000 m d’épaisseur) sont formes durant un épisode d' activité volcanique et de subsiden qui coïncide avec l' amorce de deux cycles d' affaissement de la rldera (cauldron) de Noranda. Celle-ci Jut le site exclusif d’unflux : chaleur anormalement élevé et d’une perméabilité d’origine cucturale qui ont favorise le développement d’un système hydrothermal a haute température. Les métaux proviennent soit directement d’une chambre magmatique situee afaible profondeur, so it d’un lessivage des roches de l’aquifère par l’eau de mer circulant par convection. Cette chambre magmatique, représentée maintenant par le pluton de Flavrian, se trouvait à son niveau le plus élevé dans la croute au moment de l’affaissement de la caldeira (cauldron). Les dépôts se sont constitués par un mecanisme combinant remplacement et précipitation de sulfures à partir des fluides exhalatifs, au niveau ou au-dessous du plancher océanique, de la même manière que se forment de nos jours, les dépôts de sulfures massifs au fond des océans."

Jan 1, 1990

By G. H. Long, D. H. Magnusson

THE DEFINITION of the continental margin, as considered in this paper, is in the broad sense: " ... those provinces of the continents and of the oceans which are associated with the boundary between these two first-order features of the earth" (Heezen et aL, 1959, p. 17). The provinces in the area under con-sideration are: the Continental Shelf, the Continental Slope and the Continental Rise. The Continental Shelf extends from the shoreline to the shelf break, which lies at approximately the 200-meter isobath through-out the region (except north of the Grand Banks, where the break may be defined more properly by the 400-meter isobath). The Continental Slope and Rise occur between the shelf break and the 4,000-meter isobath. (The last figure was somewhat arbitrarily selected for the purpose of this paper.) The Atlantic Continental Margin as thus defined extends along the eastern coast of Canada from the International Boundary in the Gulf of Maine northward to approximately the 60°N latitude off the coast of Labrador. The area of study amounts to at }east 500,000 square miles -an area roughly equivalent to 13 per cent of Canada's total land surface.

Jan 1, 1970

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By J. McCreedy

"The addition of Portland cement to hydraulic sand fill has resulted in the production of stable and self-supporting cemented sand fill. The use of cemented fill in the mines of The International Nickel Company has resulted in substantial economies in timber requirements, de-creased dilution of ore and greater flexibility in mining methods.Coupled with special mining techniques, it has permit-ted mining by both cut-and-fill and shrinkage stoping methods to much greater depths than heretofore. The use of cemented sand fill has permitted revisions to undercut-and-fill mining which have significantly improved the efficiency of this method.Automated mixing systems have been developed for preparing cemented sand fill in surface sand plants on a continuous throughput basis. Control of cement-sand mixtures is obtained by the use of a mass flow measuring system and weighing cement feeders."

Jan 1, 1966

By F. Melo, M. Pawlik

Fine coal aggregation in concentrated coal-water suspensions was studied through steady-state rheological measurements. The wettability of coal particles was modified by dry oxidation of a bituminous coal. The degree of hydrophobicity was monitored using film flotation. The rheological measurements revealed that hydrophobic coal particles aggregate in aqueous suspensions, over a wide pH range, and produce slurries with high yield stresses. As the degree of coal oxidation increases, the coal particles become more hydrophilic and such suspensions exhibit lower yield stresses values. The yield stress values for suspensions prepared from oxidized/hydrophilic coal become a strong function of pH and correlate well with the surface charge as determined through electroacoustic measurements. These results indicate that the yield stress of aqueous suspensions of coal, and hence coal particles aggregation, is strongly affected by the wettability of coal particles.

Jan 1, 2004

"This paper presents results of ongoing research being carried out at the University of New South Wales into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that the rock mass strength can be determined following the GSI approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions:• construction dates from 1880s to 2006• spans from 3.2 to 12.5 m• depths from 17 to 124 m• excavation methods of drill & blast, roadheader and TBM.Finite element modelling is used to assess the likely magnitudes of the stresses present at the time of failure. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zone. Failure and stable points are then compared to the rock mass strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown criterion and spalling criteria. The Hoek-Brown rock mass strength envelope differentiates between the ‘failed’ and ‘stable’ zones remarkably well.INTRODUCTIONStress induced failures of rock masses are fortunately rare in civil tunnelling. However, when they occur they provide an opportunity to calibrate an assumed rock mass strength criterion. This paper compares an estimate of rock mass strength for the Hawkesbury Sandstone with the following cases where stress induced failure occurred in tunnels excavated within Hawkesbury Sandstone.• Cataract & Devines Tunnels of the Upper Canal (Upper Nepean Scheme)• Malabar Outfall Tunnel• Sydney liquefied petroleum gas (LPG) Storage Cavern• Northside Storage Tunnel• Cross City Tunnel• Lane Cove TunnelTwo-dimensional finite element modelling is used to assess the likely magnitudes of the stresses present at the time of the failures. The principal stresses are then compared to the assessed rock mass strength envelope(s) of Hawkesbury Sandstone derived using the 2002 Hoek-Brown criterion (Hoek et al., 2002) and the spalling criterion suggested by Diederichs (2007)."

Jan 1, 2015

By C. G. Bruce

"ON NOVEMBER 15th, 1950, the Department of Mines and Technical Surveys announced the discovery of vermiculite near Perth, Ontario. The announcement followed nearly a month of study to determine so far as possible the potentialities of the deposit and quality of the material from surface indications. The mineral was identified by the writer in the field among samples submitted by Mr. Arthur Powers of Stanleyville or, September 22nd, 1950. Within a week of the announcement, mining rights to properties covering a major portion of the deposit had been acquired by commercial interests.Hitherto, Canada has had to import her entire requirements of vermiculite. Prospects of .a domestic supply gave promise of considerable benefit to many industries, particularly the building industry, and to the consumer public. Should the deposit •prove large enough there was also the possibility of exporting to centres in the United States.Field and laboratory studies were continued at the Mines Branch during the winter of 1950-51 as opportunity occurred. It is the purpose of this paper to describe the results of these •preliminary investigations, to attempt to present the Stanleyville occurrence in its proper perspective with regard to similar occurrences elsewhere, and to review the salient features of the vermiculite industry.Properties and UsesVermiculite is a hydrated magnesium aluminum silicate. In appearance it resembles mica, having the same micaceous cleavage, but it differs from that mineral in being very soft, pliable, and inelastic. Colours range from black through dark olive-green and brown to almost colourless."

Jan 1, 1952

By Lang Tao, Jun Wang, Wei Xiao, Wenqing Qin, Pan Cao, Guanzhou Qiu, Key Lab of Biohydrometallurgy of Ministry of Education, Central South University

"The effect of metal cations on the rutile flotation using styryl phosphoric acid (SPA) as the collector was investigated by micro-flotation test, bench scale flotation test, zeta-potential measurements and adsorption measurements. The micro-flotation results indicated that Fe (?) and Al (?) ions in low concentrations had obvious activation on the rutile flotation, and Pb (?) ions in low concentrations had smaller activation of rutile, but Fe (?), Al (?), Pb (?), Ca (?) and Mg (?) have strong inhibition of rutile flotation in high concentrations. The bench scale flotation results indicated ethylene diamine tetraacetic acid (EDTA), boracic acid, and sodium hexametaphospate can decrease the metal ions concentrations, and increase the recovery of rutile flotation. Adsorption measurements and zeta-potential measurements revealed that Fe (?), Al (?) and Pb (?) ions were adsorbed on the rutile surface, and had interaction with SPA. But when these ions concentration were over the largest adsorption capacity, residual metal ions could occur chemical reaction with SPA.INTRODUCTIONRutile is one of the favored minerals for production of titanium dioxide white pigment, primarily through the chloride manufacturing process (Stanaway 1994; Hou et al., 2013) However, the majority of rutile ores belong to refractory ores, while flotation is one of the most efficient methods to separate fine rutile from gangue (Dolbear et al., 1937). With the flotation development, many effective collectors were successfully applied in the oxide ore. Many reviews have indicated that organic phosphonic acid collectors showed good selectivity on oxide ores such as ilmenite and rutile (Bulatovic & Wyslouzil 1999; Liu & Peng 1999).It is inevitable that many types of metal cations are present in ore pulp. These metal cations significantly influence the flotation of minerals. Liu et al. (2015) showed that Ca2+ and Mg2+ could improve the floatability of spodumene at pH 12.5 and 10.0, respectively. The authors proposed that Ca2+ and Mg2+ ions readily form hydroxy complexes (CaOH(l) and MgOH(l)) and precipitates as (Ca(OH)2 and Mg(OH)2) in strongly alkaline solutions. Fan and Rowson (2000) investigated the effect of Pb(NO3)2 addition as an activator on ilmenite flotation and showed that it could improve ilmenite floatability. The addition of Pb(NO3)2 resulted in an increase of ilmenite zeta potential in both weakly alkaline and acidic aqueous solutions. Mehdilo, Irannajad, and Rezai (2015) studied three kinds of ilmenite of different origins and discovered that both Mg and V had a negative correlation with ilmenite flotation, while the Mn content seemed to correlate positively with flotation efficiency. A number of studies have also showed that Fe3+ can improve the floatability of ilmenite (Fan et al., 2009; Nuri, Mehdilo, & Irannajad, 2014)."

Jan 1, 2016

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The 'Design and Construct' contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The 'floating roof' principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006

By J M. Gibbs

Craigmont Mines Limited mine 50,000 tons of ore and waste per day from the open pit at Merritt, British Columbia. An electric-powered "down-the-hole" drill, a diesel-powered rotary drill and two electric-powered rotary drills have been used. All primary drilling, as a result of cost and operating experience, is now performed with two electric-powered rotary drills. Trials with various loading techniques have increased the amount of AN-FO and decreased the amount of commercially prepared slurries used for primary blasting. Approximately 95 per cent of the primary blasting is accomplished with AN -FO, mixed at the hole. Introduction THE Craigmont mine is located near the village of Merritt, B.C., 240 miles northeast of Vancouver. The concentrator has been in production since September of 1961. Craigmont is a combined open-pit and underground operation. To date, slightly more than 95 per cent of the mill feed has been mined from the open pit. As underground development proceeds, the ore requirements from the open pit will decrease. The average milling rate from September, 1961, to April, 1964, was approximately 4,900 tons per day.

Jan 1, 1965

By Sazol Das, Hany Ahmed, Ganesh Bhaskaran, Zhuoru Wu

"Friction stir welding (FSW) process in lap configuration for dissimilar materials has been developed and tested for steel to aluminum joining. A novel cylindrical tool was designed for improved material flow. The joining of steel to high strength 5xxx and 6xxx aluminum was carried out by FSW technique using optimized process parameters. The microstructure, micro-hardness, joint strength and corrosion properties at the weld interface have been investigated. Optical and scanning electron microscopy reveled a well layered structure at the interface and lap shear tests of the welds showed excellent fracture resistance. Neutral salt spray tests for up to 500 hours (ASTM B117) were carried out on the bare steel to aluminum FSW joints, which did not show neither evidence of corrosion at the weld interface, nor any degradation of the weld strength. The FSW lap configuration was applied to prototype commercial vehicle structural component whereby a steel stiffener insert was friction stir welded to high strength 6xxx aluminum alloy. The interface microstructure showed layered root without any steel shattering in aluminum side. A finite element study was carried out to quantify the benefits where it was found that the stiffness increases by 76% under bending loads and 36% in torsion loads.INTRODUCTION Energy preservation and environmental issues, namely carbon footprint and legislation around emission in transportation industries has led to a growing need to use of lightweight materials such as aluminum and magnesium alloys along with various grades of steel in structural application, while still maintaining their strength and crashworthiness. Assembling dissimilar materials within integrated structure is thus a stringent requirement related to optimum performance. In order to achieve an efficient technology of joining dissimilar materials such as aluminum to steel, it remains difficult to select an effective welding process for a given joint configuration. The use of aluminum in transportation industries for structural component is not exclusive in a design and is almost always used along with various steel grades for a mixed materials solution, thus dissimilar aluminum/steel lap joining is of great interest since this is widely used in the assembly of parts (e.g. pillar, frame rails, chassis, body in white (BIW), CAB, etc.)."

Jan 1, 2018

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By W. N. Wallinger

The mine and concentrator of Cyprus Anvil Mining Corporation are situated in south-central Yukon, some 120 miles north of Whitehorse. The large lead-zinc concentrator employs conventional crushing and grinding , followed by differential flotation, to produce selective lead and zinc concentrates, as well as a mixed lead-zinc (bulk) concentrate. Since the commencement of operations in 1969, the concentrator has undergone expansions and modifications which have increased the capacity to 10,000 tons per day, and afforded some metallurgical improvements.

Jan 1, 1978