Search Documents

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By J. S. Fox

Major-element data for unaltered, unmineralized felsic host rocks from a number of stratigraphically simple, massive volcanogenic Zn-Cu(-Pb) sulphide deposits of low metamorphic grade have been compiled. The petrochemical affinities of these host rocks have been determined (by standard means and by discriminant analysis) and compared. This comparison indicates that volcanogenic deposits in felsic terrains are not restricted to the classical calc-alkaline rock association as previously thought, but can actually be hosted by rocks showing a range of iron content. There is a positive correlation between differentiation trend and are tenor. Zn-Cu ores usually have iron-rich felsic hosts (most Canadian Shield deposits); Pb-Zn -Cu ores have iron-poor felsic hosts (Japanese, Iberian and Tasmanian deposits). This parallels the antipathetic relationship between iron content and background lead levels evident in young, unmineralized, island arcs as well as in many older belts. Correlations between differentiation trend on one hand and massive ore mineralogy and the relative proportions of various rock type (including rhyolite, quartz-porphyry and coarse pyroclastic rocks) on the other are also evident. It is concluded that the recognition of a calc-alkaline differentiation trend cannot be used as a prospecting guide, as has previously been proposed. However, in view of the above correlations, the recognition of a given trend may aid in the formulation of an effective exploration philosophy.

Jan 1, 1979

By Lionel A. York

THE first application of the cementation process took place in the year 1864, according to H. Standish Ball, when a break in the brickwork lining at a depth of 270', in one of the Rhine Preussen pits near Homburg, was sealed by running in milk of cement from the surface by means of a small hand pump. At about the same time Monsieur Portier adopted the method in France for repairing breaks in shaft lining. Figure 1 is descriptive of the Portier system and is of interest when compared with modern practice. During the next thirty years numerous attempts were made to improve the process; the general method used in sinking being to put clown bore holes outside the perimeter of the shaft for the purposes of injection. The cementation process was first recognized as an important as-set to mining in 1896 when Monsieur A. Francois developed his method of boring and injecting inside the shaft below the permanent water level. The Francois cementation process rapidly attained fame on the Continent and many shafts were sunk by its use in France, Belgium and

Jan 1, 1961

By W. G. Hubler

It has been within only the last two or three years that enough progress has been made in preferential flotation to warrant metallurgists in recommending the installation of commercial-sized plants for the treatment of copper-zinc-iron ores. Until the new processes had been worked out successfully, the treatment of this type of ore had proved a stumbling block in the path of metallurgical progress. Separation of lead-zinc ore is comparatively simple. A lead-zinc ore low in iron may be separated and concentrated by gravity con-centration, provided it is not necessary to grind too fine. Owing to the specific gravity of chalcopyrite and sphalerite being so nearly the same, however, their separation by gravity concentration is out of the question. Complex lead-zinc-iron ores in which the several minerals are intimately associated, requiring fine grinding to free them, have been successfully treated by flotation for the past fifteen years. Galena is easily floated, and its flotation, unlike that of chal¬copyrite, is not affected by the reagents used to inhibit the flotation of sphalerite and iron sulphides. When an attempt was made to use the methods of lead-zinc se-paration on copper-zinc ores, it was found that the depressant re-agents added to inhibit the flotation of the iron and zinc minerals would, under certain conditions, depress a large part of the copper. It was also recognized that, in the grinding of copper-zinc ore, soluble salts were generated which were detrimental to flotation unless properly controlled. The main part of this paper will be a discussion of solutions in the grinding circuit in relation to the pro¬duction of soluble salts and their effect on flotation.

Jan 1, 1931

By A. Holland, T. Krumins, E. Olin, J. F. M. Castilleja, J. Geldart, C. Fleming, I. Jackman

A flowsheet has been developed to treat the flotation tailings from a copper mine in Mexico to recover gold and silver by cyanidation and carbon-in-pulp (CIP). The plant will treat ~15,000 t/day of a 60:40 blend of current flotation tailings and the mine’s historic tailings. The tailings also contain a significant amount of cyanide-soluble copper, and the economic viability of the project is strengthened by recovering most of the copper and cyanide associated with this process. The solution and solid phases in the CIP tailings will be separated in a counter current decantation (CCD) circuit and the CCD solution overflow will be treated by a SART Process. Copper precipitates as a salable copper sulphide product in the SART Process and the cyanide that is associated with the copper complex is regenerated as free cyanide. After SART, a portion of the SART product solution will be recycled to leach to reuse the free cyanide, while the remaining solution will be used as wash water in the CCD circuit. Incorporation of the SART Process in the flowsheet allows the CIP circuit to be operated aggressively as a gold plant, which means most of the silver in solution passes through CIP to SART. Silver co-precipitates with copper in SART and is recovered very efficiently with the copper sulphide by-product. Incorporation of SART also allows the leach and CIP circuits to be operated with relatively high levels of free cyanide, which enhances silver leach kinetics and helps keep copper from loading onto the carbon in CIP. The flowsheet was developed in the laboratory and successfully demonstrated in a fully-integrated pilot plant in 2018.

Jan 1, 2019

By R. N. Chakravorty

Early detection of spontaneous combustion is of utmost importance in underground coal mining to prevent major disruptions of production and to ensure a safer working environment. This paper presents the work done in developing a suitable system for the early detection of heating in a hydraulic coal mine. Laboratory studies on the products of oxidation for Balmer 10 seam coal showed that a significant amount of carbon monoxide is produced during the early stages of heating and that detection methods based on the analysis of other gases, such as hydrogen, ethane or ethylene, are not a better alternative for this coal. The four-point carbon monoxide monitoring system recently installed at the hydraulic mine is discussed in this paper. It is believed that by studying the trend of carbon monoxide concentration in the mine air, it will be possible to detect heating at an early stage. Field tests carried out so far have indicated that infra-red technology will prove to be a powerful tool in the hydraulic mine, particularly for locating hidden oxidation or fire in cracks, fissures, underground workings and coal outcrop areas before it spreads extensively. The project is jointly sponsored by EMR, CANMET, Mining Research Laboratories and Kaiser Resources Ltd.

Jan 1, 1978

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By Donald Brisebois

The mining of high-grade, narrow vein deposits is an important field of activity in the precious metal mining sector. The principle factor that has undermined the profitability and effectiveness of mining such ore zones is the substantial dilution that occurs when blasting with explosives during extraction. In order to minimise dilution, the Thermal Fragmentation Mining Method enables the operator to extract a narrow mineralised corridor, 50 cm to 1 metre wide (according to the width of the vein), between two sub-level drifts. By inserting a strong burner powered by diesel fuel and compressed air into a pilot hole previously drilled directly into the vein, a thermal reaction is created, spalling the rock and enlarging the hole to 80 cm in diameter. The remaining ore between the thermal holes is broken loose using low powered explosives, leaving the waste walls intact. This patented method produces highly concentrated ore, resulting in 400% - 500% less dilution when compared to conventional mining methods. The mining method reduces the environmental affects of mining operations since much smaller quantities of rock are displaced, stockpiled, and treated using chemical agents. The fully mechanised equipment operated by a 2-person team (1 thermal fragmentation operator, 1 drilling operator) maximises the effectiveness of skilled personnel, and increases productivity and safety. The Thermal Fragmentation is currently employed in 3 mining operations in North America.

May 1, 2010

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By James F. Kelly

"Research and development on the production of liquid fuels from coal is rapidly expanding worldwide. AImost every industrialized country is engaged in coal liquefaction research and process development. In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas.A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described.IntroductionThe CANMET coal liquefaction program is made up of two interrelated parts. The first part consists of the research and development work being carried out at the Energy Research Laboratories near Ottawa, Ontario. The second focuses on contracted research and development as part of the Coal Conversion Program of Energy, Mines and Resources Canada. The long-term objective of the liquefaction program is to contribute to Canadian liquid fuels production through the definition, research, development and demonstration of different coal liquefaction technologies for the Canadian marketplace.In coal liquefaction, the main objective is to produce liquid hydrocarbons with a higher hydrogen-to-carbon (HIC) ratio than the coal feedstock while reducing heteroatom (S,O,N) content, removing mineral matter and minimizing gas production. Typical atomic HIC ratios for a variety of Canadian fossil fuels are shown in Figure I. Canadian coals have about 500/0 of the HIC ratio present in tar sand bitumens and heavy oils and only about 20% of the ratio available in methane. In general, the cost of synthetic fuels production is related to the cost of hydrogen and, therefore, to the increase of HIC ratio between feedstock and products. On this basis, the production of liquid fuels from coal would be expected to be more costly than liquid fuels produced from bitumens and heavy oils. However, for mined tar sands and some heavy oils this difference tends to be offset by the large sand content (>90 mass %) of tar sand bitumens and the increased production costs of viscous heavy oils. For example, it can easily be shown that for equal weights of distillate <525°C) yield, current coal liquefaction processes required between two and three times less mined coal by weight than the mined tar sand s required for the most technically advanced processes proposed for bitumen upgrading."

Jan 1, 1981

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing all essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.Introduction Very high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field. However, sulphur content, mainly pyritic, ranges from 1 to 2.50Jo. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required. Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs. Typical data on the various coal properties of importance in the production of coke are included in Table 1."

Jan 1, 1985

By Z. D. Hora

"There has been a number of new developments in British Columbia&apos;s industrial minerals field over the past few years. Several new industrial operations were started to diversify the line of British Columbia mineral production by magnesite, perlite and fuller&apos;s earth. Industry activities and geological projects have identified occurrences of rare earth minerals, niobium, kaoline, fireclay and zeolites. The Geological Survey Branch significantly improved its database on industrial minerals. New geological concepts based on recent work are opening a number of new opportunities f or further industrial minerals&apos; exploration and development in British Columbia.IntroductionTraditionally, the value of industrial minerals produced in British Columbia in any given year comprises between 100/0and 15% of the combined value of minerals, coal, petroleum and natural gas. Over the years a wide variety of industrial minerals has been produced , often with different levels of marketings success. For some products, such as dimension stone and clay or shale products, initial strong demand gradually dissipated; for others such as asbestos and magnesite, new discoveries or new industrial activities created demand and new markets . In some cases, such as fluorite , talc, pyrophyllite and perlite, wider use has been prevented by small size, poor quality or remote location of the deposits. Also, British Columbia , with 2.6 million inhabitant s, provides only a limited market and the industry therefore has to look beyond provincial borders."

Jan 1, 1990

By Sanat Talmaki

Construction and mining worksites pose unique challenges to workers and equipment operators due to their dynamic and unstructured nature. Narrow haul roads, crowded work spaces and presence of workers and equipment in close proximity, combined with large blind spots and overall poor visibility afforded to operators lead to collisions and run-over-type accidents between equipment, workers, and other entities that may be present on the jobsite. Operations that involve machine-infrastructure interaction, particularly in the case of concealed infrastructure such as excavation and drilling lead to unintended strikes between the equipment?s end-effect or and the infrastructure. Such accident-prone scenarios can be avoided by providing operators with real-time feedback and warnings using 3D visualization and proximity monitoring of the entities present in the equipment?s vicinity. Thus the jobsite in the real world is abstracted and represented in a 3D virtual world. However, this requires the ability to create a seamless link between real-world sensors present on the equipment and/or the jobsite and the virtual environment. This paper describes a non-restrictive acquisition allocation framework that allows position and orientation sensor streams from construction and mining job sites to be used for updating 3D virtual scenes in real-time for providing vital collision avoidance warnings to equipment operators.

Aug 1, 2013

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By S. Surapunt, C. M. Nyamai, K. Itagaki

"The use of liquid copper as a medium for zinc extraction has been used in the Warner Process as a method of processing zinc-lead sulphide ore. The recovery of zinc metal is based on the reaction:ZnS(s) + 2Cu(l) = Zn(g) + Cu2S(l)In this method, thermodynamic and phase equilibria investigations of the Cu2S-FeS-ZnS and Cu2S-PbS-ZnS systems are of importance and form the basis for the liquid sulphide phase which appears as a product and is used as a solvent in the Warner Process. Phase relations in the Cu2S-FeS-ZnS and Cu2S-PbS-ZnS ternary systems were determined experimentally at 1473°K to provide a fundamental basis for the new zinc smelting process. The results show that the solid solubility of ZnS in the two systems is very small (2 wt% to 3 wt% ZnS in FeS, 4 wt% ZnS in Cu2S for the Cu2S-FeS-ZnS system; less than 0.5 wt% ZnS in both PbS and Cu2S for the Cu2S-PbS-ZnS system). The Raoultian Activity Coefficient of ZnS in the liquid mixtures and the vapour pressure of zinc over the matte in both systems is relatively large (?° = 7.7 – 15.8, Pzn(atm) = 0.088 – 1.026 for the Cu2S-FeS-ZnS system; ?° = 8.9 – 12.9, PZn(atm) = 0.075 – 0.214 for the Cu2S-PbS-ZnS system). On the FeS-ZnS join, the only phases detected are FeS and iron-rich sphalerite (Zn, Fe)S. The binary join mixture occurs at about 92 wt% FeS-8 wt% ZnS at 1473°K. Electron microprobe examination of the quenched samples indicate about 47 wt% to 48 wt% FeS in sphalerite and about 2 wt% to 3 wt% ZnS in the iron sulphide phase. On the Cu2S-ZnS join, microprobe analysis reveals that the maximum solubility is 4 wt% Zn in liquid Cu2S and 3.6 wt% Cu in solid ZnS. In the Cu2S-PbS-ZnS ternary system, microprobe analysis of the quenched samples indicate on average, 5 wt% ZnS in the liquid phase region. The only phases detected on the PbS- ZnS join are ZnS and PbS. The eutectic phase contains, on average, 13 wt% ZnS. The phase relationships, very low solid solubilities of zinc sulphide in the liquid mixtures of both Cu2S-FeS-ZnS and Cu2S-PbS-ZnS systems, coupled with the high Raoultian Activity Coefficient of ZnS as well as the high vapour pressure of zinc over matte all favour the partitioning of zinc metal into the vapour phase. This new process is cost effective and bypassesthe expensive and tedious conventionaltechnique of zinc production involving oxidationof the sulphide ore by roasting followed bya reduction process to extract the zinc. Theresults indicate that a new zinc smelting technologyusing the Warner Process would bemore efficient and preferable over the traditionalmethods of zinc extraction."

Jan 1, 2002

By T. R. C. Aston, C. M. K. Yuen, J. L. Gilby

"The access tunnels for the Donkin-Morien Mine in Cape Breton, Nova Scotia, comprise two parallel tunnels driven through a sedimentary sequence of sandstone, siltstone and mudstone to intersect the Harbour Coal Seam under the Atlantic Ocean, approximately 3.5 km offshore (Fig. 1). The No. 2 tunnel was driven a total distance of 3579 m using a 7.6 m diameter Loyat full-face tunnel boring machine (TBM) and was supported by steel sets. The No. 3 tunnel was initially driven a distance of 1027 m using drill and blast methods (dimensions 7.6 m wide by 5.3 m high) supported by rock bolts and shotcrete. This tunnel was then completed (front March 1986 to February 1987) using the tunnel boring machine to a distance of 3573 m.During the period May 1983 to December 1984, a major geotechnical research program was undertaken in the Donkin-Morien tunnels by Golder Associates in conjunction w,ith CANMET and the Cape Breton Development Corporation (Yuen et al., 1985). The research program included the monitoring of the performance of the TBM and drill and blast drivages, and the study of the thrusting characteristics and rock-interaction of the TBM excavation. The main emphasis of the research program was on the collection of field data which was to be made available in the form of a comprehensive report for the future use of others who might wish to carry out a detailed interpretation and analysis. The information gained from the program was also used during the tunnel"

Jan 1, 1988

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016

By J. Lui

Inco Copper Cliff Smelter commissioned two new Inco flash furnaces in 1991/1993 as part of its S02 abatement program. Each flash furnace is equipped with a fluid bed dryer. The ~ 12 wt% water content in the concentrate filter cake, flux, reverts and sludge is removed in the fluid bed dryer. The dry solids are discharged from the dryer together with exhaust gases into the baghouses where they are separated. The dry solids are transferred to four storage bins. In September 2003, for the first time since startup in 1991/1993, a large amount of elemental sulfur accumulation was discovered on the walls, roofs and floors of the outlet side of the baghouse chambers. Several baghouse fires were experienced during cleaning and conducting maintenance work in the elemental sulfur contaminated baghouses. Laboratory scale test work at the Inco research lab was conducted to understand the mechanism. A plant solution to minimize elemental sulfur formation was implemented with success. This paper summarizes the efforts to understand and minimize elemental sulfur formation in the baghouse chambers.

Jan 1, 2007

"The Val d&apos;Or Division now comprises the Lucien C. Beliveau Mine and Concentrator (formerly the Pascalis, described below) and the Chimo Mine. Cambior acquired an initial 50% interest in the Chimo Mine in May 1989 and the remaining 50% in April 1990. Cambior&apos;s share of 1989 production was 2121 ounces; the company expects to net 23 750 ounces from Chimo in 1990. Pascalis MineUPDATERenamed the Lucien C. Beliveau Mine at its official inauguration in September 1989, the mine is exceeding forecasts, producing over 11 500 ounces of gold in the first half of 1990. Cambior expects 1990 production to total 34 000 ounces.IntroductionThe Pascalis Mine is located 16 miles east o f Val d&apos;Or, Quebec, and is accessible by a three mile gravel road off highway 117 (Fig. I).The property is wholly owned by Cambior.The Pascalis gold deposit consists o f a sub-vertical diorite dyke 1000 ft long by 30 ft wide containing quartz and tourmaline veins with inclusions of pyrite and native gold . Three vein systems ca n be seen in the deposit , the most important being tensile veins oriented at a right angle to the direction of the dyke and inclined at 40 degrees. These overlapping veins vary in thickness from 4 in. to 40 in. and occur at intervals of six to ten ft. The deposit is, therefore, very difficult to evaluate; a complete evaluation would require drifts over the whole width of the dyke combined with relatively short drill holes (Fig . 2)."

Jan 1, 1990