Search Documents

By Art Hamilton

Abstract -The Zn-Pb-Cu-Ag ore deposits of the Boundary and N-5 zones near Bathurst, New Brunswick, occur in a polydeformed volcano-sedimentary sequence that is part of the Ordovician Tetagouche Group. Massive and disseminated sulfides are hosted by an argillaceous to cherty sedimentary sequence that is stratigraphically underlain by a siliceous fragmental unit and is overlain by a feldspar-rich crystal tuff and related tuffaceous rocks. The deposits have a low iron sulfide con­ tent relative to that of most stratabound sulfide deposits of the Bathurst-Newcastle mining district. The ore is commonly associated with chlorite- and talc-rich sediments. The N-5 deposit is considered to be the fault-displaced extension of the Boundary deposit. The Boundary deposit is estimated to contain 891 000 t grading 3.310Jo Pb, 7.96% Zn, 0.32% Cu and 44 g/t Ag; the estimate for the N-5 zone is 330 000 t grading 3.24% Pb, 7.15% Zn, 0.33% Cu, and 37 g/t Ag. The ore is processed at 1000 tpd at the Heath Steele mill.

Jan 1, 1992

By A. E. Cameron

The theory of atomic distribution of the stranger atoms in the space lattice of the solvent metal has been well developed by Rosenhain. It has long been known that the addition of one metal to another to form a solid solution increases the strength and hardness of the solvent metal. This increase is practically proportional to the amount of added substance up to the limit of solid solubility. To account for this increase in hardness and strength, Rosenhain assumes that the stranger atoms occupy positions on the solvent metal space lattice. Atomic attractions about the stranger atoms will not be the same as in the case of the pure metal, and there will thus be a disturbance of the orderly arrangement of the atoms on the space lattice, or a distortion of the lattice. Such a disturbance would interfere with the ease of slip along the planes and would thus tend to promote strength and hardness. Rosenhain notes that not only may there be a local disturbance of the lattice about the stranger atom but there may well be also a measurable change in the dimensions of the lattice as a whole. The relative amounts of local and general distortion of the lattice will depend upon the nature of the lattice itself. As Rosenhain says, "If the lattice is comparatively soft and flexible the distortion is likely to be largely local. In a stiff lattice, however, local distortion will be resisted and there will be a correspondingly increased general distortion."

Jan 1, 1927

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By Yin Wang, Lin Li, Zhongwei Bi, Like Wei, Wen Li, Shaogang Li, Bin Zhang, Hongjie Li

Presently,Many long-wall fully-mechanized faces in shallow depth coal seams are below room and pillar goaf in Shendong mining area. When the working face is advanced out of concentrated coal pillar in upper room and pillar goaf, strong strata behaviors often cause support crushing accident. Aiming at a support crushing accident which happened in Shigetai coal mine of Shenhua group in Shendong mining area, this paper analyses the stress transfer process while mining out of concentrated coal pillar by numerical simulation software FLAC3D. According to the feature, simplifying the roof of upper room and pillar goaf as supporting-beam structure explains mechanism of large area collapse in room and pillar goaf roof. Based on the feature of supporting-beam structure, deep-hole blasting concentrated coal pillar technology is proposed to control the strong strata behaviors in Shigetai coal mine. The blasting control effect is confirmed through characteristics of strata behaviors, growth circumstance of ground crack and multi-point extensometer monitoring results. By using control technology, Shigetai coal mine has been successfully avoided support crushing accident.

Jan 1, 2015

By M. M. Williams

WESTERN CAN ADA'S coal industry has experienced a serious set-back since 1949, following a pattern well known to its counterpart in the United States. The loss in coal markets in Western Canada has been particularly severe as the discovery of large reserves of oil and natural gas and the subsequent construction of re-fineries and pipelines roughly coincided with the dieselization of both main railways. While the coal industry will have to face a further decline in markets of long standing, others with a large growth potential can be se-cured if present marketing methods are changed where needed and if fundamental and applied research programmes are actively pursued. The energy and chemical potential of Western Canada's coals will eventually find their place in the ever-growing needs of industry and electric power producers. Electric power generation would appear to offer the largest and most immediate market for coal. If the coal industry is to serve this market adequately and gain as much of it as possible, coal operators ? must have a good knowledge of certain characteristics -of the electric utility industry and its fuel requirements. This paper is prepared primarily to set out some of these characteristics, but also discusses other probable markets for coal.

Jan 1, 1958

By T. G. Carter

"This paper traces the introduction and use of fire-resistant (FR) fluids in hydraulic systems at underground mines in British Columbia. Reasons are given for the decision to make compulsory the use of such fluids in underground mines after January 1, 1975 by provincial government legislation. Examples are quoted of fires caused, or supported by, mineral oils which have resulted in loss of life and property.The basic principles of hydraulic systems are reviewed in order to present the effects of changing a system operating on mineral oils to one which must operate on FR fluids. Approximations of the cost of system conversions are given for certain machines and a brief survey is made of the various pieces of underground equipment which contain hydraulic systems operating on FR fluids.IntroductionIn 1948, Admiral Ben Moreel , who was then president of Jones and Laughlin Steel Corporation in the United States , wrote:""Although safe and healthful working conditions can be justified on a cold dollars-and- cents basis, I prefer to justify them on the basic principle that it is the right thing to do. ""(1)This paper will outline the introduction and use of fire resistant fluids at mine operations in the Province of British Columbia. That it was the right thing to do in enhancing the safety and well-being of every person employed at the mines was the prime consideration. That it may be justified on a cold dollars-and-cents basis is left for the reader to judge. The prime purpose of this paper is not so much to trace the efforts made by the individual mines to successfully introduce and use fire-resistant (FR) fluids in hydraulic systems, but to present an over-all picture of what occurred, in a collective sense, at the majority of mines which have ended up with a working FR fluid system. The problems attendant to the introduction of an FR fluid will be recounted in a manner which, it is hoped, will prove useful to those contemplating system conversions. Because the predominant fluid now in use is an invert, or water-in-oil. emulsion, this will be the FR fluid considered.Fluid Loss from SystemsThe quantities of various fluids required for use in hydraulic systems are extremely high. This statement in itself may appear to be redundant in that the capacities of the various systems should demand that a fixed amount of fluid is required for the initial filling of a system, with a further amount of fluid scheduled for use during subsequent fluid changes, i.e. at the recommended change intervals . If only this were the case!"

Jan 1, 1981

By R. K. Collings

The annual production of mineral and mineral-based wastes in Canada is conservatively estimated to be 400 million tons. Over 90 per cent of this amount is waste rock or mill tailings from the mining and mineral processing industry. The remainder are slags and ashes from the metallurgical industry, and sludges from the chemical industry. Because of impurity content, remote location, or both, most wastes have limited usefulness and, indeed, are a liability in that they must be transported to waste disposal sites and contained therein. Certain mineral wastes do, however, have potential value. Some contain small percentages of metals that may be economically recoverable with price increases; others consist of mineral material that may be used for such purposes as road base, construction aggregate, railroad ballast, and in the manufacture of bricks or blocks. Increased interest has been shown in mineral wastes in recent years. This paper reviews the types of mineral wastes available in Canada, briefly describes a number that have potential value, and notes possible uses and related research by CANMET and other organizations.

Jan 1, 1978

By Jehan Rondot

Les trois intrusions alcalines de Suzorite en haute Mauricie, bien que non datees, son! sans doute d ,attacher aU)( nombreuses autres intrusions alcalines dispersees sur les blocks Grenvillia et Laurentia et datees de I 050 Ma =t= 10%, done reliees d l'orogene grenvilien. L 'utilisations de la Suzorite est liee d sa forte proportion de phlogopite (>50%). Le rapport Mg/Fey varie de 3 d 7. Sa mineralogie et sa composition particulieres (forte proportion de Mg, Ket H20) en font son attrait.

Jan 1, 1984

By L. Gutierrez, M. Pawlik

The rheology artificial mixtures of bitumen with fine quartz of varying bitumen content, as well as actual oil sand ores, was investigated under different physicochemical conditions (pH, temperature). All rheological measurements were conducted using a Haake Rotovisco VT550 rotational viscometer, connected to a fixture specifically designed to measure properties of settling suspensions. It was found that at low bitumen contents (1 %, wt.) the pH of the slurries was the most important parameter that controlled the rheology of quartz-bitumen slurries. At higher bitumen contents (10%, wt.), it was a combination of high temperature and high pH that gave the lowest apparent viscosities and yield stresses of the model mixtures. These model observations correlated well with the rheology data obtained for slurries of actual oil sand ores. The overall results were discussed in terms of aggregation-dispersion phenomena between bitumen and mineral particles.

Jan 1, 2009

By J. A. Abols, P. M. Grady

Recovery via gravity is one of the oldest mineral processing methods available. Unfortunately, the use of gravity techniques for gold recovery has been in decline for the past century as more effective chemical processes such as flotation and leach/CIP have been developed. Recently, with the push towards more sustainable environmental outcomes, the benefits of gravity separation have become more apparent. While gravity as a unit process is not usually capable of achieving as high a recovery as flotation or whole ore cyanidation, a combination of gravity devices alone or in conjunction with these processes can offer significant advantages to the operator. This paper reviews the range of gravity devices available, their application and the results that can be achieved by maximizing gravity through the use of a combination of gravity recovery devices. Three case studies are provided.

Jan 1, 2005

By I. B. Schalamuk, R. E. de Barrio, M. J. Pons, M. B. Franchini, L. Meinert

"Several Fe, Fe-Cu, and Cu-Ag prospects hosted by Mesozoic carbonate-rich sedimentary rocks that were intruded by diorite stocks define an approximately 20 × 200 km belt along the Andes Cordillera of southwest Mendoza province, Argentina (34°-36°S). This belt includes the Hierro Indio and Vegas Peladas Fe skarns, Las Choicas, and several other Cu-(Ag) prospects.The main features of the Fe skarns include: association with mantle-derived middle Miocene (~15-11 Ma) diorite stocks and sills; widespread alteration including epidote ± amphibole ± magnetite endoskarns, and zoned garnet (Grs0-66 Adr32.5-100) ± magnetite ± pyroxene (Di24-50 Jo2-9 Hd74-41) exoskarns formed from oxidized, saline, high-temperature brines (530º-660ºC; 60-70 wt.% NaCl equiv.); and magnetite-hematite orebodies associated with quartz ± epidote ± calcite ± actinolite formed at lower temperatures (290º-436ºC) from saline fluids (32-50 wt.% NaCl equiv.) of magmatic origin.West of the Fe skarn belt, the Valle Hermoso district covers more than 300 km2 and hosts several poorly known Cu-(Ag) prospects (estimated 30 Mt with 1.5% Cu and 20 g/t Ag). These prospects share many characteristics with the iron oxide copper-gold-type systems and manto-type Cu deposits of northern and central Chile. One of the prospects (Las Choicas) is located at the apex of a regional 015°-trending anticline, along the contact of stratified calcareous sandstone and limestone (Neocallovian-Oxfordian) with a diorite pluton. This pluton has positive Ta and Nb anomalies (on normalized diagrams) and a high Ti content, features uncommon in Miocene diorites associated with Fe skarns and of magmas derived from sub-arc mantle sources. Alteration at Las Choicas includes early widespread chlorite + calcite ± albite ± scapolite ± ilmenite or titanite ± apatite, and local actinolite ± hematite ± biotite alteration of diorite and sedimentary rocks along contacts. Later Cu mineralization (1%-10% Cu) is associated with calcite ± albite ± quartz alteration in fractures, vein networks, and crackle breccias. Mineralization is zoned from bornite ± chalcopyrite ± millerite with Zn, As, Mo, Ag, and U anomalies in the main orebody, through chalcopyrite-rich breccias with Zn anomalies, and chalcopyrite ± tetrahedrite vein networks with Sb, As, Ag, and Zn anomalies in the uppermost zone, to a Cu-depleted pyrite-rich envelope with Co anomalies, and finally to late, barren calcite veins in distal zones."

Jan 1, 2007

By H. Itou

A mechanism of scorodite formation at ambient pressure was investigated using transmission electron microscopy (TEM). Several types of iron arsenate were obtained from Fe/As solutions (Fe/As = 1.0 and 1.5) at pH values of 1.0, 1.25 and 1.5 at 95°C. Amorphous FeAsO4.xH2O was precipitated from solutions having a higher mole ratio of Fe/As at pH l.5, even after 9 hours. A few micron sized particles were observed by SEM, but these proved to be agglomerates of 10-50 nm amorphous FeAsarxH2O particles when observed by TEM. This means that supersaturation of the solution causes the acceleration of nucleation of iron arsenate hydrate. Crystalline scorodite was obtained from a solution in which the Fe/As mole ratio was unity, at pH l.0 and pH 1.5, after 3 hours. Almond-type crystalline scorodite particles were observed by TEM and most of them showed high crystallinity. The addition of scorodite seed material enhanced the crystallization. Amorphous FeAsO4.xH2O, however, was observed at the surface of the seeds during the early stages of precipitation. It is postulated that crystalline scorodite is not directly precipitated even on crystalline scorodite seeds, but requires a certain time to crystallize on the seed material.

Jan 1, 2006

By L. Veleva, Garcia. A., G. Perez

Aluminum is a metal used for the transmission of electricity of high voltage, in the construction industry and other areas. In atmospheric conditions aluminum forms an oxide layer (Alz03'H20) as a result of its corrosion, entering the passive state. The oxide layer can be destroyed by the presence of ions (Cr, SOx-n) developing localized (non uniform) corrosion attack by pitting, difficult for evaluation. The concepts of fractals and self-similarity were used in this study for the characterization of the development of localized corrosion. Images obtained with a scanning electron microscope (SEM) of samples of electrolytic aluminum wire that have been exposed during one year in ruralurban and marine-coastal environments of the humid tropical climate of Mexico, have been processed. The development of pitting has been studied as a function of time, making a statistics of the frequency of appearance of pits versus the area occupied by them. The data show that the distribution of the pits follows a power law. Therefore, the concept of self-similarity can be applied for the study of the phenomenon of localized corrosion, describing their development with time.

Jan 1, 2006

By G. W. MacLeod

The iron ore question in this country has been widely discussed for many years, but only recently has its real significance becoming generally understood. The exhaustion of the old Helen mine, in 1918, marked the last phase of hematite production in Ontario, and with the closing of the Magpie mine in 1921 , Canada ceased to be a producer of iron ore. For the past three years every ton of ore used in Canadian blast furnaces has been imported. In a recent issue of the Engineering and Mining Journal-Press, Arthur B. Pearsons, Assistant Editor, makes the following statement : Iron dominates the world. Some contend that coal is more vital. be-cause heat is needed to make iron and steel. But there are other sources of energy, more convenient and less costly and it is only a question of time when progress in hydro-electric development will have reached the point where coal will be but an incidental source of power and heat. Even more direct means than the generation of electricity by hydro-power eventu-ally will be developed by making available the latent energy of the sun. But iron; Science gives not the vaguest suggestion that anything will dis-place iron and steel as the most essential material tool of modem civiliza-tion. ? Hardness, tenacity, malleability-it possesses all these in unique de-gree. These are some of the qualities that make steel and iron indispensable in modern industry. The domestic consumption per inhabitant of the United States has climbed uniformly from 0.18 tons in 1900, to 0.36 tons in 1922. New kinds of machines and new types of structures are being devised every year; and steel or iron is the basis of most of them." It is unlikely that the Ontario Government were actuated by this motive when they appointed the Iron Ore Committee to investigate and report on the iron ore situation, nevertheless, these facts must have influenced them in some degree.

Jan 1, 1924

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By Robert B. Parsons

"Investors in flow-through shares are going to need an expanded road map to find their way through a growing maze of tax rules affecting such shares. At the end of 1985, no fewer than three new sets of important tax amendments were tabled which could have a significant effect on flow-through share issues. This proposed legislation is discussed this month in Tax Notes.IntroductionIn a flurry of legislative activity at the end of 1985, the federal government tabled legislation which includes the introduction of new rules which will have a notable effect on investors in flow-through shares and on companies that issue such shares.First, on November 26, 1985, Bill C-84, the legislation to implement most of the changes announced in the May budget, was introduced in Parliament. This legislation includes the rules for the $500,000 capital gains exemption, a matter of considerable interest to flow through share investors.Next, on December 2, 1985, the government tabled a Notice of Ways and Means Motion which would extend the time horizon for spending flow-through share funds to include the 60-day period following the calendar year. But all news was not good news. On December 4 the government released its proposals for a minimum personal income tax, which would include rules that would catch an investor's CEE expenses and capital gains."

Jan 1, 1986

By X. -P. Zhang, L. N. Y. Wong

Shale gas exploitation initiated in North America has rapidly extended worldwide. Hydraulic fracturing is an emerging field technique for stimulating the gas reservoir. The study of cracking processes, particularly crack coalescence, is vital for a successful hydraulic fracturing to enhance the gas exploitation. Experimental studies have observed that the size effects of the constituent particles are significant on the cracking behavior of the rock specimens. To further investigate the size effects, the bonded-particle model (BPM), which is based on the discrete element method (DEM), is adopted in the present research. In flaw-containing specimens, by varying the crack resolution (?= a/2R), which is the ratio of half flaw length (a) to particle size (2R), the size effects on cracking behavior under compressive loading are studied. By keeping the flaw length constant, the particle size is varied independently in the BPM analysis. Decreasing the crack resolution increases the first crack initiation stress, but it has no obvious effects on the uniaxial compressive strength. The trajectories of the first cracks and secondary cracks hence generated have a higher resolution and are well-defined in those specimens possessing a higher crack resolution. On the contrary, in lower crack resolution specimens, the macroscopic first cracks appear to be wider and less continuous. These findings from numerical simulation clearly demonstrate particle size effects on cracking behavior. Special attention should be paid to these effects in future numerical study using the bonded particle model.

Jan 1, 2015

By Lionel A. York

This paper outlines the type of water-bearing formations encountered in the Prairie Sediments and describes a method for effectively sealing these zones in order that shaft-sinking operations may be carried out with safety. Details are given of the procedure for carrying probe holes ahead of the shaft bottom. These probe or grout holes are employed for establishing a series of overlapping grout covers around the proposed shaft excavation to safeguard against large inflows of water during sinking. The pattern and length of grout covers cannot be standardized, and each cover needs to be specially designed to suit the varying ground conditions. In order to provide effective protection through the Prairie Sediments, the number of holes in any one cover would not be less than 8, and possibly as many as 64 would be required in certain zones. The length of covers would vary from 100 ft. to 250 ft. Emphasis is placed on the need for obtaining accurate geological and water information from exploratory holes, drilled in the shaft vicinity, in order to effectively plan all grout covers.

Jan 1, 1964