Search Documents

By Y. Luo

The rock breakage process in drilling is a main source of noise in roof bolting operations, especially when hard rocks are encountered. Proper control of drilling operation can provide an opportunity to improve energy efficiency of drilling and to reduce noise and heat generated from bit-rock friction. Drilling tests have been conducted in laboratory settings to confirm this noise-reduction strategy. Preliminary results show that the drilling parameters, penetration and rotational rates can be controlled to achieve in a desirable range in drilling medium hard rock. Based on the theoretical and experimental studies, rational drilling control strategy is developed for noise control while maintaining a safe and productive roof bolting operation. Applying this strategy in underground roof bolting operation, the noise exposure of roof bolter operators will be significantly reduced.

Aug 1, 2013

By S. Kelebek, E. Yalcin

"Diethylenetriamine (DETA) and/or triethylenetetramine (TETA) are reagents that can generally be categorized under ""flotation modifiers"". These polyamines are known to be effective for the deactivation/depression of pyrrhotite that is present in Canadian nickel-copper sulphide ores in large quantities. Recent bench scale testing on some of these complex ores indicated that chalcopyrite flotation can also be adversely affected under certain conditions involving polyamines, which may be taken to be an evidence of their specific affinity towards chalcopyrite. In general, DETA shows no significant depressant action on chalcopyrite while TETA's promotion of hydrophilicity for this mineral has been observed even in the presence of xanthate. This prompted an investigation on thermodynamic equilibria involving these polyamines and copper ions. Results serve a useful purpose to identify conditions for deactivation phenomena. CuDETA2+ and CuTETA2+ chelates as products of sequestration have large predominance areas covering a wide range of redox and pH conditions, where copper xanthate species are not stable, especially in the presence of TETA."

Jan 1, 2009

By L. F. Haven

"The desirable shovel speed-torque curves are described, along with the characteristics of the more important electrical components used to approximate these curves. A particular shovel regulator system combining these components is discussed in detail and some of the advantages and disadvantages of the system are given.INTRODUCTIONIN 1959, STATIC CONTROL was for the first time successfully applied, installed and operated on a mining machine in North America. Since that time, a great deal has been learned about this control by the people maintaining these machines as well as by the de-signers.In 1961, the first SCR (Silicon Controlled Rectifier) or thyristor control system was installed on an excavator. This control differed from the earlier static control in that thyristor excitors supplied the generator fields directly. The development of thyristors of a sufficient rating to supply amounts of phase-controlled power to the generator fields eliminated the bulky Mag. Amp. -Rectifier combination previously used."

Jan 1, 1969

By M. Kunst

The creep behavior of three AJ62 alloys was investigated in a wide range of stresses and temperatures. Multi-level tensile creep tests revealed a distinct primary creep stage and a high stress exponent up to a value of 10. The threshold stress concept which is commonly used in combination with high stress exponents was utilized in the analysis of creep behaviour. This resulted in an effective stress exponent for the AJ alloys indi¬cating dislocation climb as the dominating creep mechanism. In addition, microstructural observations of the lamellar eutectic and of the a-Mg-matrix were carried out using opti¬cal microscopy, SEM and TEM. The creep properties of the alloys are discussed in the context of microstructural parameters such as phase volume-fraction, stability and solute supersaturation.

Jan 1, 2006

By B. K. Choi, S. H. Kang, G. E. Kim, K. B. Kim, S. Noh, T. K. Kim, H. J. Jin

Oxide dispersion strengthened (ODS) steel is being considered as an in-core structural material of future nuclear reactor systems because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperature in a ferritic/martensitic matrix. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. The primary activity is to develop high strength advanced ODS steel, fabrication technology for the structural components and key joining technology for the component fabrication. As a result, a Fe-10Cr-1Mo alloy with a superior creep resistance at high temperatures has been developed. An optimized fabrication process of this alloy system has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. Joining technology for the ODS steel components is also being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. These R&D activities will contribute to the realization of ODS materials for future nuclear reactor system applications.

Jan 1, 2015

By E. Dernedde

Cell rooms of aluminium smelters have large openings in the sidewalls and in the roof. These openings provide a high ventilation rate, which removes heat and contaminants emitted by the reduction cells and thereby ensures acceptable working conditions inside the cell room. However the large openings make the airflows through the smelter building sensitive to the wind. In this study equations for the airflow through the openings of a smelter building exposed to crosswinds were developed and verified against plant measurements. The equations were then used to estimate the airflows through a two-storeyed smelter building containing VS Soderberg cells. Wind protection by wind-covers over the sidewall openings and by upwind buildings made the airflows through the building less sensitive to the wind. Physical and mathematical modelling showed that working conditions inside the wind-protected cell room would be acceptable for crosswinds at speeds up to 16 km/h. These predictions were confirmed by measurements taken in a VS Soderberg smelter.

Jan 1, 2007

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By K. H. March

In the present very highly competitive condition of the bituminous coal business, it is becoming increasingly apparent that coal mines which do not lend themselves to efficient mechanization cannot long survive. It would seem that those mining operations best fitted to survive the struggle for existence are burdened with the considerable capital and maintenance cast of carefully selected mechanical and electrical mining equipment. The ever changing conditions of coal mine operations require equipment which is adaptable to a variety of uses; and investigation of the mechanical and electrical equipment in most mines will show that the operating duty of much of this equipment is considerably different from that duty for which it was originally selected. And it would appear that one of the essential qualifications for a successful mine management is a marked ability to get satisfactory operating results from equipment which has been transferred from some other operation, rebuilt, rearranged, or in some way adapted to the job at hand. As a striking example of such mechanical ingenuity, many of us recall that the first longwall jigging conveyor used in Nova Scotia was built in Sydney Mines from odds and ends in the scrap pile at a total cost of less than $50.

Jan 1, 1930

Innovation ? In economics a change must increase overall value, customer value, or producer value. ? Innovations are intended to make someone better off, and the succession of many innovations adds growth to the whole economy. ? Innovation may refer to both radical and incremental changes to either products, processes or services.

Feb 1, 2008

By P. Wanjara, M. Xiao

During fusion welding of aluminium alloys, the avoidance of defects (such as porosity, oxides, hot cracking, undercutting) as well as the ability to optimize the microstructure-property characteristics in the assembly are critical for the stringent manufacturing specifications in the aerospace industry. In this work, aluminium alloy (AA) 2024 was electron beam welded autogenously as part of a study to determine the influence of parametric conditions on the characteristics of the heat affected and fusion zones to obtain optimal welding conditions. In particular the evolution in the weld geometry, microstructure and mechanical properties were examined as function of the processing conditions, including beam current, beam focus, beam oscillation, linear heat input and welding speed. For optimized parametric conditions, microstructural examination of the joints revealed narrow fusion and heat-affected zones comprising of dendritic structures without the occurrence of defects that enabled a maximized joint efficiency.

Jan 1, 2006

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By R. Wang

"Under high stress conditions, rock bursts, borehole breakouts, and spalling events are common phenomena that occur around underground openings. In general, together these three phenomena represent brittle failures of an intact rock mass; however, individually they reflect different failure modes under high stresses. After analyzing and comparing the stress-to-strength criteria for rock bursts, borehole breakouts, and spalling events, proposed by previous researchers, it is found that these brittle failure phenomena share common stress-to-strength prerequisite. The stress-to-strength preconditions for brittle failures can be defined by the ratio of the maximum tangential stress around an underground opening to the uniaxial compressive strength (UCS) (s?max/sci) or by the ratio of the maximum far-field principal stress to the UCS (s1/sci). Both these indicators can be used to reflect the same stress preconditions. For s?max/sci, a ratio of 0.4±0.1 represents the critical stress requirement for brittle fracture. However, for s1/sci, a ratio of 0.15±0.05 should be considered as the critical stress requirement. Numerous engineering case studies and analysis of rock mechanics based on the Hoek-Brown criterion also verify these two stress-to-strength preconditions. Here, these two indicators are presented with an error range because complex rock mass quality ratings, lithology, and geotechnical conditions have profound impacts on the stress-to-strength preconditions for brittle failures. INTRODUCTIONHigh stresses are one of the most important factors that must be considered when undertaking underground rock mass projects (Kaiser et al., 1998). Wang et al. (2009) reviewed current progress in the evaluation of high stresses and their corresponding criteria. However, after clarifying the definition of high stress, civil engineers need to understand the deformation and failure behaviors of rock mass around an opening under high stresses. Under high stress conditions, the deformation of rock masses around an opening can be categorized into two groups, i.e., severe brittle failures (or rock bursts) and compressional plastic deformation of the surrounding rock mass, as indicated in Figure 1."

Jan 1, 2015

By Charles Camsell

At the last annual meeting of this Institute the programme very properly was drawn up and carried out with the special object of calling attention to the Dominion's position and problems with regard to fuel supplies. That subject, always one of serious concern, was a source of considerable anxiety twelve months ago. It is still so, but in a decidedly less degree than at that time. So far as the immediate fuel situation is concerned our anxieties have been relieved. And I think we can safely say that such a consciousness of our difficulties and determination to overcome them, has been developed in the minds of our people that there will be no slackening of the offensive until a final solution is reached. In selecting a subject of major importance for the present occasion I have felt free to digress from the pressing problems of last year and to go back, for a starting point, to the presidential address of two years ago .. I do not, however, wish to enter the controversy that has developed as a result of that address, though in spite of my own failure to amass a fortune from participation in certain mining ventures, I am decidedly inclined to the optimistic view that Dr. Corless presented of the future of our mining industry. You will perhaps have observed that in its general wording the title of my paper bears a marked resemblance to that of that address. This simila1ity of titles is not accidental. It is intentional on my part.

Jan 1, 1924

By C. H. Sleeman

"The Iron Ore Company of Canada constructed a beneficiation complex in Sept-Iles, Quebec, to concentrate and pelletize earthy red hematite iron ores from the Knob Lake area. The plants were scheduled for initial production during the first quarter of 1973.Many problems have been experienced to date. Difficulties in controlling the process, excessive mechanical failures, design deficiencies and manpower-staffing problems have caused an extended start-up. The problems are now essentially solved and, with the completion of some additional minor modifications, it is expected that the plants will be producing premium iron ore pellets at or near rated capacity within the next immediate period."

Jan 1, 1976

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By DON E. MacDONALD

Marl in Alberta is confined to highly specific geological, hydrogeologica/ and climatic settings. Tufa is fa irly abundant in those areas of western Alberta where bedrock is of the Paskapoo Formation. Marl and tufa originate when the following conditions are met: presence of a carbonate source in drift or nearsurface bedrock; leaching of the carbonate by percolating groundwater; transportation of calcium and bicarbonate ions in a permeable aquifer; discharge at the surface as springs, seeps or lakes; re-precipitation of calcium carbonate. Alberta has seven categories of marl and tufa deposits, based upon over-all depositional environment and calcium carbonate

Jan 1, 1984

By Larry T. Yano, Gerald T. Handford

"Tailings Engineering has the responsibility for planning and coordinating tailings disposal and for ensuring the stability of the tailings dyke. The inclusion of both the planning and geotechnical functions in one team has resulted in greater efficiency in the design and planning process. Major challenges in tailings disposal facing Syncrude are in the areas of: (1) sludge disposal; (2) instrumentation and monitoring; and (3) liquefaction. Meeting these challenges will have a significant effect on the cost effectiveness and reliability of the mining operation.IntroductionThe size of the tailings disposal operation has led to the establishment of a large engineering team devoted solely to the disposal of tailings. This paper discusses: the tailings disposal operation, the role of tailings engineering, the organization, inter faces, and the present and future challenges with respect to tailings disposal."

Jan 1, 1990

This paper examines the latest advances in mine hoist motor and drives systems. The technology employed for large hoists has migrated from the traditional DC technology to AC motors with cyclo convertor drives, and more recently, advances in pulse width modulation (PWM) drives have resulted in these being applied to large hoist drives. When combined with PWM drive technology, the induction motor presents the ideal solution for hoist applications This paper examines the factors in choosing a suitable PWM drive and motor for a hoist installation. Factors under consideration include: ? hoist duty cycle, ? drive rating restrictions, ? choice of power semiconductor device,, ? low speed operation, ? maintenance ? reliability The cage induction motor and synchronous motor are compared and it is shown that the induction motor is the motor of choice for large hoists.

May 1, 2010

By H. D. B. Wilson

"IntroductionRECENT ADVANCES in geo-chemistry and in •our knowledge •of crystal structure provide a key which enables us to create a systematic picture of the genesis of many ore deposits. This genetic scheme may be used with confidence in assessing certain types of orebodies and may be of some aid in actual exploration, since it affords a rational explanation of the dependence of the composition •of the ore minerals on that of the rock type in which they occur with which they -are •associated. For purposes of the present paper, .the elements chosen are •chromium, vanadium, iron, and titanium. The oxides of all these metals occur in deposits of similar or related type, and it is proposed to show that, for each, the composition of the •ore mineral is related to •the composition of the enclosing :rock, and that one of the principal factors controlling the composition of the ore is the ionic size of its constituent elements.Geochemical PrinciplesThe crystals of the rock-forming silicates and of the magmatic oxide minerals are essentially ionic types. This means that they are composed •of oppositely charged ions such as Mg²+ and 0²-, which are held together by electrostatic attraction. The ions of each element are spherical, with characteristic size known as the ionic radius. Crystals are built up by the packing of these spheres in the most stable arrangement compatible with the size and the size and valence of the ions• involved.Many of the principles governing the formation of ionic crystals are •simple ,and logical."

Jan 1, 1953

By Douglas A. Grieg

THE EXCUSE for producing still another paper dealing with the oilfields of the Middle East is the overwhelming importance of this area to everyone, both inside and out of the oil industry. Figure 1 shows the area defined as the Middle East for the purpose of this paper. No description of what constitutes the Middle East is generally acceptable to everyone and, in fact, in many parts of the world it is referred to as "Western Asia". At the time ?the writer went to work as a geologist in the Middle East -this was in 1926 -there were just three known oilfields, namely, Hurghada in Egypt, Naft Khaneh in the Transferred Territories of Iraq, and Masjid-i-Sulai-man in Persia. Their combined producing rate at that time was around 100,000 barrels per day. Toda y, just thirty years later, some forty-two fields have been proven to exist, and a recent discovery in Syria -if commercial -may add one more to the list. Producing rates at the end of last year ( 1956) were approaching four million barrels per day. This sizable figure re presents nearly 23 per cent of the total Free World's production. What is more important still, something over 70 per cent of the Free World's proven oil reserves are known to exist in the subsoil of the Middle East.

Jan 1, 1957