Search Documents

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

By Tim Watson

Andacollo Hypogene Project ?Overview Project description: Sulphide copper concentrator Throughput:55,000 tpd Location: Approximately 50 km from La Serena Elevation: Approximately 1,000 m ASL Start feasibility study: July 2005 Start of construction: May 2007 Construction completion: December 2009 Final cost(1,2,3):435 Million US $ (1) Excludes third party costs, 220 kV power line (2) Cost is based on a Chilean Peso to US Dollar foreign exchange rate of 535 to 1 (3) Does not include US$40.3 million for the Elqui River Pipeline Project or US$8.0 million for the stock pile cover

May 1, 2010

By G. H. Agnew

When water floods are initiated after gas-oil ratios have increased, the transition period from the start of injection until" the gas-oil ratios are returned to the solution gas-oil ratio may be important for either economic or technical reasons. The transition period is longest, and consequently most critical in water floods where injection is equal to withdrawals. This paper describes a theoretical basis for predicting the behavior of such a system and outlines a procedure for making the necessary calculations. The calculation procedure is illustrated for two actual cases: a line drive water flood and a five spot water flood. In each case there is a reasonable similarity between the actual and calculated performance.

Jan 1, 1960

By Rob Kelso

What is a Lunabot? ?Robot Controlled Remotely or Autonomously ?Visual and Auditory Isolation from Operator ?Excavates Black Point 1 (BP-1) Simulant ?Weight Limit - 80 kg ?Dimension Limits - 1.5m width x .75m length x .75m height ?Designed, Built and Tested by University Student Teams

May 1, 2013

By F. J. Tozer

Canal communication between Lake Erie and Lake Ontario has been one of almost constant enlargement and reconstruction to meet the rapid growth of trade and commerce, and the consequent steady increase in the size of vessels plying the Great Lakes. The original canal was built by the Welland Canal Company. The first sod was turned in 1824 and the first vessel passed through in. 1829. There were 36 lift-locks, built of oak timber, 110 feet long and 22 feet wide, with a depth of water over the sills of 8 feet. The second canal, now known as the 'Old Welland Canal' was built by the Dominion of Canada (1842 to 1850). There were 26 masonry locks, 150 feet long, 26.5 feet wide and with a depth of water over the sills of 9 feet. The walls and banks were raised in 1853 to give a 10-foot draught. The third canal, known as the 'New Welland Canal, built by the Dominion of Canada, was started in June 1874 and the first boat passed through in the spring of 1882. There are 25 masonry lift-locks, 270 feet long, 45 feet wide and with a depth of water over the sills of 12 feet. The walls and banks were raised in 1891 to give a 14-foot draught. This is the canal in use at present.

Jan 1, 1926

By J. J. Gillman

"The coal deposits from Cape Perce on Cape Breton Island have been known to supply the coal requirements of the people living in or visiting the area for close to 300 years.A major block of coal has been identified off Cape Perce, which has several seams from which coal can be taken. The initial development by the Cape Breton Development Corporation will be in the Harbour Seam and constitutes the Donkin-Morien Development Project.The CBDC's confidence in this indicated resource is based on its knowledge of the Sydney Coal Field and from boreholes driven into the block during the summers of1977, 78 and 79. In 1980, further geological data were gathered from surface drilling and an intermediate-depth high-resolution seismic survey. The surface facilities for the Donkin-Morien Development Project will be located on the northern half of the cape, with access declines extending 3.9 km in a north-northeasterly direction to the Donkin block of coal reserves. The development has the potential of supplying all the coal needed f or the future electrical power generation requirements of Nova Scotia for many years to come.The planned mine, for which a project definition study has recently been completed, will have a production rate in excess of 3 million tonnes per year.IntroductionAt the Second CIM District 1 Meeting held in Halifax in October 1980, a background paper on Phase II of the Donkin-Morien Development Project was presented. The project involves a 3.2-million-tonne, saleable, underground coal mine. At that time, the chronological sequence of events had unfolded, starting with the initial boreholes through to the feasibility study, and on through site clearing and site preparation. This led to engineering design contracts for the portals and the two tunnels to be driven to intersect with the Harbour Seam close to 4 km from their entry point."

Jan 1, 1982

By L. Li

Backfill is increasingly used in underground mines, as it can help reduce the environmental impact from mining operations. However, the primary objective of backfilling is to provide safe working space for miners, by improving ground stability conditions. As cement is often added to the backfill, a critical issue is the determination of the required backfill strength (cohesion) due to the binder. This value is usually obtained from a solution proposed by Mitchell and co-workers, in the early 1980?s, for stopes with an exposed backfill face. This paper presents a brief review of the Mitchell et al. solution, with some of its main limitations. Some of the recently developed solutions for backfill design are then summarized and discussed.

Aug 1, 2013

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By K. S. Raja, F. Battick, B. Pesic

"CeO2 doped with lower valence cations, such as Y3+, Sm3+, Gd3+ etc. is considered as electrolyte material for low temperature SOFC. Doping introduces additional oxygen vacancies and improves ionic conductivity. This work describes the preparation of yttria-calcia doped-ceria precursor material, its sintering in DC and AC field methods, and characterization of sintered electrolytes with respect to the ionic conductivity. Doped precursor materials were prepared by a controlled co-precipitation process. Sintering of prepared, pelletized particulates was carried out using three different methods such as: 1) conventional; 2) spark plasma sintering; and 3) an alternating current field at 1125°C (AC assisted sintering). The mechanism involved in the conductivity improvement as a function of defect density, grain boundary area and phase stability will be discussed. INTRODUCTIONThe performance of SOFCs depends highly on the properties of materials. Subtle variations in the composition, microstructure, or density of SOFC components can considerably alter the power output capabilities of fuel cells. Early SOFCs utilized zirconia based electrolytes but efforts in lowering the operating temperatures of SOFCs have prompted investigations into several other oxygen ion conductors – often modified with dopants to either promote the formation of oxygen vacancies or to stabilize a vacancy rich high temperature phase – such as bismuth oxide, lanthanum gallate, and ceria.The transport of oxygen ions through the electrolyte first begins with diffusion into the material. While this is generally a surface kinetics phenomenon, it is safe to say that it is highly dependent on oxygen pressure and vacancy gradients. The role of the cathode in SOFCs is to reduce oxygen at the electrolyte surface creating an O2– ion gradient which induces permeation into the material. Once inside and under the influence of a potential field, O2– ions migrate by a vacancy hopping mechanism, Catlow, C.R.A. (1990), effectively exchanging positions throughout the matrix until they reach the anode and react, thus leaving the matrix."

Jan 1, 2012

By H. Tudeshki

A great amount of aggregate is utilized in civil engineering applications such as road construction, railway infrastructure, concrete production, etc. Igneous rocks are the preferred raw material due to their high strength and abrasion resistance. Rock quality assurance is a key factor and has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous aggregate rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure, i.e. disintegrate and degrade. This phenomenon has a great influence on the quality, strength and durability of aggregates. In the last decades, different methods and procedures such as the glycol test, the methylene blue dye test, as well as the Los Angeles test, have been introduced to distinguish rock properties, and to identify these problems. However, as these wet-chemical methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and are only possible to be accomplished under laboratory conditions, their application has always been severely limited. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used in the day-to-day routine of a mine for quality control of the quarry´s daily production. Our research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. Our new approach is based on two rock parameters: magnetic susceptibility and loss on ignition. The measurement of these parameters provides reliable information on the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. Our new approach has been assessed through extensive field and laboratory studies and has been implemented on the drill-cuttings of a basaltic andesite quarry. The results of the experiments are discussed in detail, including their impact on increasing resources and environmental protection.

Aug 1, 2013

By P. D. S. St. Pierre

IN REGENT YEARS, blast furnace operators have found it necessary to improve their technology in order to handle increasingly low-grade feed and yet satisfy the demands for greater tonnages of metal. Studies have been made covering several aspects of the problem, and in this connection the slags produced in the iron-making process have been critically examined with a view to discovering the slag with the optimum properties for a given operation. A good slag should combine, as far as possible, the properties listed in Table I. Unfortunately, some of these desirable properties are incompatible. For example, the advantage of the small ?bulk of a low-flux slag is offset by its low desulphurization potential and high viscosity. Similarly, a very fluid slag increases refractory wear. It will be seen, then, that a balance must he struck between these conflicting requirements. In the .present paper only the melting relationships of blast furnace slag ?compositions will be considered in detail. In interpreting the data herein presented, the optimum property requirements listed in Table 1 must strictly be borne in mind. It should also be noted that the discussion presented here always relates to calcined fluxes, since this facilitates reference to the final slag composition. Thus, in making calculations pertaining to the ?burdening of the furnace, due allowance should ?be made for the fact that the fluxes are added as carbonates.

Jan 1, 1956

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By P. Trudel, M. A. . Cloutier

This lithogeochemical study demonstrates that the Gilman and Blondeau Formations in the Chibougamau area belong to a subalkaline suite of tholeiitic affinity poor in potassium. The Gilman Formation is composed mostly of basalts, with subordinate andesites and rare dacites, while the Blondeau Formation comprises all lithologies of the basalt-andesite-dacite-rhyodacite-rhyolite ensemble. Both AFM and Harker variation diagrams show that all these rocks originated by differentiation from the same magma reservoir, and are related to one volcanic episode, This study did not, however, identify hydrothermal alteration zones useful for regional geochemical prospect ion.

Jan 1, 1984

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting's Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

By J. Koike

Mg alloys for structural application have attracted much attention. However, high process cost and poor mechanical reliability are major concerns upon expanding the application to a wider area. In order to break through these barriers, better ductility is desired at lower temperature. Plastic anisotropy and peculiar twin formation appear to play key roles in the deformation and fracture mechanisms of Mg alloys. In the paper, dislocation slip and twin formation are reviewed. The effects of crystallographic texture and grain size are discussed. The results suggest that a good control of microstructure and texture can improve ductility and mechanical reliability of Mg alloys.

Jan 1, 2006

By DALE MacGREGOR, VERA TUREK

lndusmin Limited acquired the St. Donat quartzite deposit in 1967 to produce high-quality silica for use in the sandblasting and silicon carbide industries. The quartzite, of Grenville age, is highly friable and porous. This is due to numerous small, kaolinite-coated cavities in the quartzite; the cavities were formed through leaching, probably by rising hot solutions.

Jan 1, 1984

By Gareth Barnes

Traditional approach to improvement is driven by good ideas from good people, but whilst the business case may sound good, when the project is complete, we often have not delivered on expectations.  Why not? The best way to successfully predict the outcomes of an improvement effort in a complex process is through using statistical modelling, which considers the impact of uncertainty within interacting processes.  Applying Theory of Constraints in a model helps leaders to quickly determine: Where the constraining process(es) is/are Where improvements will add the most value How much improvement should be targeted - before the next constraint takes over The confidence level of achieving a given target, which gives us a clear pathway to improvement. This paper presents an analysis of statistical modelling applications at Vale’s Manitoba Operations to achieve the 2025 targets. Using statistical modelling of the Business Structure, the team identified a series of process improvements through a Theory of Constraints Analysis. Value Stream Maps (VSMs) were used to define the required data, apply statistical modelling, and conduct training sessions enabling the Manitoba team to identify the constraining influences. Scenario testing in the Statistical models helped identify the Hierarchy of Constraints and specify the pathway to improvement. How to Improve a Business Video link https://vimeo.com/344418155

May 4, 2025

By P. M. Daignault

"Fording Coal Limited is one of Canada's largest producers of metallurgical coal for the export market. Medium- to highvolatile coals are mined at its Fording River operations in southeastern British Columbia. This paper discusses some of the mine design and production related problems encountered, and how they have been resolved. Other aspects of the operation such as geography, geology and standard mining methods employed are also covered.IntroductionFording Coal Limited was formed in 1968 to mine and market metallurgical coal resources held by the company in the East Kootenay region of southeastern British Columbia<1>. The company, at its Fording River operations, holds approximately 19,635 hectares of coal lands, having an estimated resource of 3.5 billion tonnes of metallurgical coal. Total reserves are approximately 520 million tonnes.Fording Coal is owned 600Jo by Canadian Pacific Enterprises Limited and 400Jo by Cominco Limited. Cominco itself is owned approximately 540Jo by Canadian Pacific Enterprises. The company, originally staffed and managed by Cominco, has been independent since January 1978, with its own board of directors, management, staff and employees. The head office is in Calgary, Alberta. The Fording River operations are located in British Columbia, approximately 70 km north of the Crowsnest Pass, near the Alberta/ British Columbia boundary, only 150 km by air and 320 km by road from Calgary.A contract was signed in 1969 with the Japanese steel mills to provide 45. 7 million tonnes of metallurgical coal over fifteen years, commencing in 1972, at an annual rate of 3 .05 million tonnes per year. The mine is presently expanding annual production capacity from the original 3.0 million long tons (3.05 million tonnes) to in excess of 5.0 million tonnes.Concurrent with this production expansion, a vigorous marketing effort has diversified Fording's customers to include additional countries in the Pacific Rim area. Three cleaned coal products are now marketed compared to the single ""standard blend"" product originally shipped to satisfy the Japanese contract. The product specifications are listed in Table I."

Jan 1, 1985

By Yann Sivry, S. Subramanian, Divyasree C. Prabhakaran, Jean Riotte

The potential of a bacterial strain isolated from water samples collected from a chromite mine in Odisha, India has been assessed for the bioremediation of hexavalent chromium, a toxic environmental pollutant. The isolate was identified as Sphingopyxis sp., a Gram negative bacterium, adopting molecular biological protocols and biochemical characterization techniques. Detailed investigations on the bioremoval of Cr(VI) were carried out using Sphingopyxis sp. cells and the various parameters affecting the biosorption process were evaluated. About 55 % biosorption of Cr(VI) was obtained using Sphingopyxis sp. bacterial cells and the residual chromium in solution was found to be bio-reduced to the trivalent form, namely Cr(III). Thus, complete bioremediation of Cr(VI) could be achieved using the mine isolate, with contributions from both biosorption and bioreduction mechanisms. The Cr(VI) biosorption isotherm obtained for the isolate was found to follow a typical Langmuirian behavior and the free energy value of biosorption was determined to be ~-25 kJ/mol, indicative of involvement of chemical binding forces in the bioremediation process. The chromium biosorption kinetics by the isolate followed a pseudo second order reaction. The FTIR spectral studies revealed that carboxyl, hydroxyl, amino and phosphate groups were involved in the biosorption process. X-ray photoelectron spectroscopic studies on the bacterial cells interacted with Cr(VI) confirmed the presence of both Cr(VI) and Cr(III) on the cell surface. The electrokinetic studies revealed that the surface potential of the bacterial cells were less electronegative subsequent to interaction with Cr(VI), compared to the cells alone, which further testified to the binding of positively charged Cr(III) ions, formed by bioreduction of Cr(VI), to the bacterial cell surface. A marginal shift in the iso-electric point obtained for the bacterial cells interacted with Cr(VI), corroborated the involvement of chemical binding forces in the bioremediation process.

Jan 1, 2016