Search Documents

By D. Royston

Reducing SAG Mill feed size has been a major trend in recent years. ?Mine to mill? strategies have reduced blasted-rock size, and in a growing number of operations reducing the primary crusher CSS and/or adding additional crushing upstream of the SAG mill have reduced rock feed size. While reducing feed size will increase SAG mill throughput, issues arise in terms of retaining charge in the mill, exposing the shell lining to impact damage, and maintaining milling performance should the pre-crush system shut down. This paper reviews the past experience on pre-crushing for SAG mills and provides an analysis of liner design (in particular grates and shell liners) for pre-crushed feed.

Jan 1, 2012

By J. Stachulak

In recent years more emphasis has been placed on the control of nitrogen dioxide (NO2) emissions from mining diesel equipment. Worldwide, diesel engine regulations to control emission and protect the environment are also driving the development of the diesel engine technology to reduce oxides of nitrogen NOx (Nitric oxide, NO + NO2). NOx are toxic gases produced in mines during the operation of diesel equipment. Most of the diesel equipment used in underground operations are equipped with Diesel Oxidization Catalysts (DOCs) designed to reduce carbon monoxide (CO) and hydrocarbons (HC). The effects of DOCs on NO2 production from diesel powered equipment is not well understood. DOCs do not alter NOx concentration, but may promote the oxidization of engine exhaust NO to the more toxic NO2, thus increasing the undesirable NO2 exposure of workers in the mine environment. In 2012, the ACGIH reduced the NO2 TLV concentration value from 3 ppm to 0.2 ppm. Vale and CanmetMINING have been involved in several research projects to reduce diesel emissions exposure to workers. One aspect of the current program is to determine the effects of in-use DOCs on NO2 production. Several in-use DOCs taken from mining equipment were selected for testing in the laboratory using ISO 8178-C1 and mine LHD transient test cycles. The paper presents the laboratory test results and effects of DOCs on NO2 production. The results indicate significant reductions in CO concentration, by over 77%, while increases in NO2 varied from 46% to 315% based on the ISO 8178-C1 8-mode steady state test cycle. The mine LHD transient test cycle showed the same pattern, although the magnitude of CO reduction was less. Consequently, it is recommended the use of only those DOCs that have been properly evaluated and shown not to significantly increase NO2 emission in the environment be used on mine equipment.

Aug 1, 2013

By Vladislava A. Ignatkina, Fillip O. Milovich, Vladimir A. Bocharov

"Complex research of flotation concentrates of monomineral fractions of chalcopyrite, sphalerite, galena, pyrite, pyrrhotite included methods of adsorption of collectors, surface compounds by IR ATR, and surface films of flotoreagents by TEM. They revealed that the proportion of the parts of thionocarbamate (TC) and dithiophosphate had an effect on the adsorption rate of the components of minerals, on the presence of characteristic bands, and, what is an important, visualized surface film of organic flotation reagents on the particles of concentrates by TEM. The predominance of thionocarbamate in a composition selectively increases the adsorption rate constant of the components and recovery of chalcopyrite compared with sphalerite and galena. The highest flotation rate using TC is characteristic for chalcopyrite (0.62 min- 1) in case of individual use, and it's in combination with butyl xanthate (25% butyl xanthate or 3:1) 0.89 min-1 too. We studied the ternary blend - dithiophosphate: thionocarbamates: butyl xanthate. The increase of the proportion of butyl xanthate in combination reduces the contrast of the flotation rate among all sulfides.Practice flotation of refractory sulfide copper-zinc ores of the Urals (content sulfide iron - 75- 95%) confirmed that the use of a combination of selective collectors increases selective recovery of copper sulfide minerals up to 50% at the first fraction that is the conditioned copper concentrate. New selective sulfhydryl collectors resulted in high levels of recovery of copper into a concentrate - more than 90% - against 70-72% (butyl xanthate) from copper-pyrite ore. Low floatability of iron sulfides has been obtained by selective sulfhydryl collectors. Using weak selective sulfhydryl collectors can reduce pH into collective or selective flotation from pH 10-10.5 to pH = 7.2-7.5, which improves the quality of individual concentrates of nonferrous metals and their recovery. The same is true for polymetalic sulfide ore. The volume of gold recovery also increased."

Jan 1, 2016

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By H. Aaltonen, T. G. Robinson, M. Morimitsu

"The energy required to plate pure zinc can be the most significant operating cost for an operator in the production of electrolytic zinc. This paper reports on developments on low energy Outotec coated titanium anode process technology with fully amorphous coatings, MSA®, and its application to brownfield zinc electrowinning operations around the world. This technology aims to reduce the operating cost and increase productivity for zinc producers.INTRODUCTIONZinc electrowinning is an energy-intensive process using more than 3,000 kWh/t of electric energy [1-4], and the reduction of the energy consumption is one of the key issues. The high energy consumption is due to a high cell voltage during electrolysis, which is mainly caused by a high overpotential of oxygen evolution reaction on lead alloy anodes which have been widely used in commercial zinc electrowinning processes. The overpotential of oxygen evolution is 0.6 V or more and which is approximately 4 times higher on average than that of the cathodic reaction (zinc deposition) [3,4]. Therefore, the reduction of oxygen overpotential is significant to reduce the electric energy consumption, and this will become more significant with increasing demand in metal production and rising energy costs.Oxide coated titanium anodes have been widely investigated for the oxygen evolution anodes in order to replace the lead alloy anodes [5-9], because it is known that the oxygen overpotential strongly depends on the material and structure of the anode. The most typical example of such anodes is an IrO2-Ta2O5 coated titanium anode, which is usually prepared at thermal decomposition of a precursor solution containing metal salts at 450 oC or more and obtained mixed oxide coating consists of crystalline IrO2 and amorphous Ta2O5. On the other hand, one of the authors of this paper, Professor Morimitsu, Doshisha University in Japan, has developed a novel oxide coated titanium anode, MSA® [10-25]. The most specialized point of MSA® is that the catalytic coatings are prepared at low thermal decomposition temperature and amorphous IrO2 or RuO2 is contained as the components in the coatings. Such amorphous coatings have high catalytic activity for oxygen evolution compared to lead alloy or crystalline coatings. Outotec acquired the international specialized MSA® patent licensing rights from Doshisha University and has produced and commercialized the amorphous oxide coated titanium anodes. These anodes have already been utilized mainly in copper electrowinning plants worldwide and have demonstrated a significant voltage reduction, a cost-efficiency, and a long lifetime. This novel technology is also effective to zinc electrowinning process, thus this paper presents the characterization and performance of amorphous IrO2-Ta2O5 coated titanium anodes and amorphous RuO2-Ta2O5 coated titanium anodes for oxygen evolution in zinc electrowinning."

Jan 1, 2016

By Ham. Y. M.

The corrosion behaviour of Al-B4C metal matrix composites immersed in 2500 ppm boron-containing H3B03, 0.5 M K2SO4, and 3.5% NaC1 solutions was investigated. Effects of B4C particle volume fraction on the corrosion behaviour of composites were studied using potentiodynamic polarization and electrochemical impedance spectroscopy techniques. Scanning electron microscopy was employed to study the surface morphology of the material before and after corrosion. Results show that all materials investigated are more corrosion resistant in 2500 ppm boron-containing H3B03 than in other solutions. No appreciable corrosion was observed in boric acid and sulfate solutions in contrast to an obvious pitting in NaC1 solution for both base alloy and composites. The preferential pitting sites are the interfaces of Al/Fe intermetallics for the base alloy, and the A1/B4C interfaces for the composites. Increasing the volume fraction of B4C particles in the composite decreases its corrosion resistance of Al-B4C composites.

Jan 1, 2011

By Mathieu Dubé

Good mechanical strength of green iron ore pellets is required to avoid breakage and excessive deformation during their handling and further processing. However, green balls with good resistance to handling are often too plastic, which impacts the bed permeability in induration furnaces. Measurements of plasticity, bed void fraction and green ball sphericity as well as bed permeability were carried out on various samples of green iron ore pellets having different mechanical strength. Results show that bed void fraction, sphericity and permeability all depend, to some extent, upon green ball mechanical strength (plasticity). Understanding and controlling the mechanical strength of green iron ore pellets would then help to maximize both the productivity of the induration process as well as the quality of fired pellets through a more stable firing process. Results of research work carried out at COREM, with the objective of improving green ball characterization methods, are presented in this paper.

May 1, 2007

By Z. Luo, China University of Mining & Technology, C. Duan

"The magnetic separation removal rate of pyrite could be improved effectively by increasing the susceptibility of pyrite. The electromagnetic characteristics and absorption response performance of high-sulfur fine coal were studied in strengthening the susceptibility of pyrite. In the process of treating the sample through the microwave, electromagnetic energy could be converted into heat energy due to dielectric loss and magnetic loss. The RL(dB) was evaluate the performance of absorption response of coal. The microwave improved the susceptibility was in ultra-high frequency region, which is the most natural resonance. The absorption fine coal to microwave was strengthened and microwave energy was improved by adding the magnetite powder with double loss characteristics as the microwave absorber. The dielectric properties and permeability characteristics of the fine coal trend were investigated by maxing magnetite powder. The microwave absorption in different coal thickness was surveyed through the reflection of energy loss.INTRODUCTIONMicrowave desulfurization is one of the most important research directions (Haque, 1999; Makul, Rattanadecho, & Agrawal, 2014; Su, Tang, Zhang, Jing, & Bai, 2014). The working principle of microwave absorption response can be briefly described as the interaction of the sample with microwave energy, which will result in the microwave energy converting into heat energy loss (Keangin & Rattanadecho, 2013). For specific samples, the polarization effect includes multiple polarization mechanisms(Meikap, Purohit, & Mahadevan, 2005). Different polarization mechanisms have different occurrence time and dominant mechanisms. Meantime, energy consumption will be occurred during the process of polarization effect (Chelgani & Jorjani, 2011; Rowson & Rice, 1990) . The absorption of microwave energy in the fine coal is a process of electromagnetic response (Znamenácková, Lovás, Mockovciaková, Jakabský, & Briancin, 2005). Microwave transfers the electromagnetic waves into the heat energy by microwave dielectric loss and magnetic loss for achieving the absorption of microwave energy in the treatment of samples (Lee, Kim, Kim, Chung, & Kim, 2004). The additive magnetic medium is Fe3O4 belonging to microwave energy absorber of double loss medium (Uslu, Atalay, & Arol, 2003)."

Jan 1, 2016

By V. F. Kozyrev, L. B. Tsymbulov, L. Sh. Tsemekhman, A. N. Golov

Gipronickel Institute, JS has developed a new process and equipment for melting copper raw material in a two-zone Vaniukov furnace resulting in the production of white matte and low-grade slag in terms of copper content. Tests on processing copper nickelcontaining ore from Norilsk (Cu - 17 %), Ni - 3 %) were conducted in Vaniukov pilot furnace (total area 11.4m2) of Severonickel Combine. The amount of the processed material was about 11 thousand tons. Principal results of pilot testing are presented.

Jan 1, 2007

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By D. Auerswald, M. Kotze, V. Yahorava, T. Udayar

Uranium can be recovered from lower grade uranium ores (<800 mg/kg U3O8), leach residues, and waste dumps cost-effectively via resin-in-pulp (RIP). Using this technology, no solid/liquid separation or washing of the leach residues are required. Furthermore, the uranium recovery can be higher than with conventional methods. RIP technologies have, however, been perceived negatively due to concerns around potential resin fouling and losses. This paper highlights the advancements made in RIP and discusses a number of potential applications where the technology could deliver economic and consequential environmental benefits by reducing the uranium levels in the waste.

Jan 1, 2014

By Albert G. Zima

THE conservation of strategic materials during war rime gives rise to many problems not commonly encountered in times of peace. During normal times, when world trade is unrestricted, we are apt to become lavish to a point of extravagance in our use of those materials which, during rime of war, become scarce owing to inadequate transportation and production facilities or because the enemy may be in position to control sources of supply. It becomes necessary, then, to enforce rationing of available sup-plies, and in some cases, where such supplies are wholly inadequate, we find we must resort to the use of substitute materials. We are now confronted with such a problem to an extent never before experienced, with the result that many of the commodities upon which our civilization depended are now either shut off completely or, because of the heavy demand occasioned by war production, are not available in sufficient quantities to meet requirements predicated on peace-time standards and manufacturing methods. It has become necessary, therefore, to make many changes, some of them very drastic indeed, to enable us to carry on our war effort effectively. This? discussion will deal briefly with one phase of this problem, namely, the conservation of alloys required in the making of steels necessary for war production. In line with a request from the War Production Board, the Technical Committee on Alloy Steels of the American Iron and Steel Institute made a study of experimental steels embodying the !east amount of alloying constituents, with the objective in mind of substituting these steels wherever possible for the standard alloy steels used heretofore. This study embraced the following phases: (1) The availability of silicon and manganese; (2) The average quantity of alloying elements recoverable from scrap; (3) The effect of increases in manganese and silicon contents on the general properties of steel; ( 4) The elements and ranges of elements which might be used to duplicate the hardenability of the steels now in use; (5) The effect of combining several elements in small quantities upon the properties of steel at various hardness and strength levels; (6) A determination as to whether or not the steels selected would suffice for general application. Working on this basis, the Committee arranged for the manufacture of several heats of steels containing various combinations of different amounts of such elements as silicon, manganese, chromium, nickel, and molybdenum. The steels thus produced were compared by hardenability tests.

Jan 1, 1943

By G. F. Doggett

In describing accounting methods at Lake Shore Mines, it is the intention of the writer to limit the discussion to the principal features of the system used in securing cost figures and other statistics. The subject can be conveniently treated under the following divisions: (1) Time-keeping and Labour Distribution (2) Supplies: Handling and Distribution (3) Method of Assembling Data for Cost Purposes (4) Details of Operating Costs Time-Keeping and Labour Distribution After a new employee has gone through the routine of being &apos;hired on&apos;, he is assigned an employment number corresponding with the group applying to his occupation. This is for identification purposes in the plant and time office. He is also given an individual serial number, the use of which will be refer-red to later. On entering and leaving the plant, each employee passes through the clock room adjoining the time office, where he registers the time in and out on time recorders, on the clock card (Figure 1) bearing his name and number. It is the duty each morning of the time clerk to extend the hours worked by each employee, as indicated by the clock for the previous day, and at the end of the half-month period the total hours are multiplied by the rate and entered in the space provided for total wages at the bottom of the card.

Jan 1, 1935

By S. Banisi, E. Arghavani, A. Akbari, Gh. A. Parsapour, S. Darvish Tafvizi

The new copper processing plant of the Sarcheshmeh copper complex consists of two parallel circuits. After a primary crushing, the ore is sent to a SAG mill and the product is further ground in a ball mill. The overflow of the hydrocyclones is fed to a flotation circuit which contains 8 rougher tank cells (RCS130), 3 cleaner cells (RCS50), 5 scavenger cells (RCS50) and a 4 x 12 m flotation column as recleaner. The circuit was initially designed to process a feed containing 0.8% Cu, but because of the ore type change, the feed grade decreased to 0.6% Cu. This resulted in a reduction of final concentrate grade and recovery from 28 and 85.5% to 24 and 84.4%, respectively. Based on the original design, the copper and silica recovery in the cleaner cells should be 69 and 55%, respectively, but these values increased to 85 and 75% because of a higher retention time. The rather high silica recovery (i.e., 75%) was found to be the main source of the lower final concentrate grade. In order to reduce the retention time of particles in the cleaner cell from 13.7 to 6.9 min, the rougher concentrates of two parallel circuits were fed to only one cleaner-scavenger and regrind circuit. This modification increased the cleaner and final concentrate grade from 15.1 and 24.5% to 17 and 26%, respectively. To prevent a possible reduction in the copper recovery, the froth depth in the scavenger cells was reduced. The overall outcome of the circuit modification was evaluated to be a 10% reduction in the energy consumption without any loss in the overall copper recovery.

Jan 1, 2016

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By D. Maddocks

"IntroductionThe greater part of the iron ore industry in Canada is located along the Labrador-Quebec border on a geological formation known as the Labrador trough. The Labrador trough is a 700 · mile long geosynclinal segment composed of folded and faulted Proterozoic sediments, volcanics and intrusives, extending from Gagnon, Quebec, to the north west tip of Ungava Bay. This geosyncline can be divided into three parts (Fig. 1).The northern unmined part, extending from southern to northern Ungava Bay, is a low grade metamorphosed iron formation.The iron deposits of the central region, represented by Schefferville, are hematite-limonite ores formed by oxidation and leaching of an unmetamorphosed taconite formation. Average iron content of the ore is greater than 540Jo for direct shipping and 50% for plant feed.The deposits of the southern section (Carol Lake, Wabush, Mt. Wright, Gagnon) extend from just north of Carol Lake to Gagnon and is a metamorphosed silica-iron oxide (specular hematite and magnetite) formation averaging plus 30% iron.The mineral wealth of this area was first observed by Father Louis Babel about 1870 and again by Dr. A.P. Low of the Geological Survey of Canada in 1894. However, the remote location hindered development until after 1945. First production of direct shipping ore from Schefferville was in 1954. Production at Carol Lake commenced in 1962.This area now accounts for sixty million long tons (61 Mt) per year of processed iron ore products as follows:This chapter will concentrate on pelletizing and agglomeration as experienced at the Iron Ore Company's Carol Lake operation. However, whenever possible, reference will be made to alternate methods, procedures, equipment, etc."

Jan 1, 1989

By Timothy W. Ellis, Abbas H. Mirza, R. David Prengaman

Recycled lead, i.e. material produced by the recycling of lead-acid batteries, has become the primary source of lead in much of the world. This has been important to the recycled lead industry as other uses have dwindled, e.g. lead based pigments, chemicals, fuel additives, solders and CRT glasses. Presently, battery manufacturing accounts for greater than 85% of lead consumption worldwide while recycled lead accounts for approximately the same market share of lead supply. Battery manufacturing and production of recycled lead are intimately coupled. In 2007, of all the industrial base metals, lead from lead-acid batteries had the highest recycling rate in North America at greater than 95%. In this paper we will review some of the processes and technologies used in a modern lead acid battery recycling facility, and how recycled lead has become the material of choice for battery construction through the development of a recovery and refining process that exceeds the industry requirements. We will also briefly review an advanced air emissions treatment system in a modern lead recycling plant that demonstrates the feasibility of a new maximum available control technology (MACT) for secondary lead smelters.

Jan 1, 2011

By V. Songmene, A. Tahan, J. P. Michaud

The machining of thin wall parts, often used in the aeronautical industry still creates a number of problems, including panel deformation. Quality and productivity are often affected. This study seeks to determine the optimal conditions for cutting in order to guarantee a competitive fabrication of parts while still maintaining quality and delivery deadlines. The studied model (Spar) is a typical structural part used in the assembly of airplane wings. The main objective of this study was to improve two performance aspects: surface quality finish (quality criteria) and the rate of cutting by stock removal (economic criteria). To achieve this objective, we used an evaluation process of the geometrical error issuing from the machine-tool. We also determined the stability zones of the machine-tool&apos;s dynamic system. Finally, a series of high-speed machining tests (finishing cuts) were conducted using an experimental structured approach (16 000 - 24 000 rpm). Profile measures of surface roughness and cycle times registered during trials allowed us to establish optimal cutting conditions. Surface roughness improved as well as cutting by stock removal. Four parameters were taken into consideration: axial depth of cut, chip load, spindle speed, and cutting fluid. Finally, the influence of the type of cutting fluid was evaluated to show that it did not significantly affect machining results.

Jan 1, 2006

By Jesus Garcia Iglesias, Jorge Loredo

"Abstract -The Asturian fluorspar district consists of vein and stratiform deposits where mineralization is controlled by a combination of lithological and tectonic factors.It is postulated that these fluorspar deposits have been formed under disequilibrium conditions created during circulation of ascending hydrothermal solutions along faults and other high permeability conduits. Mixing of solutions is inferred from fluid inclusion studies. Cavity filling and replacement processes are very important in localizing the ore deposits and in determining their morphology.Permian volcanic rocks in the area yield a regional positive geochemical anomaly in fluorine implying that Permian vulcanism may be a possible primary source of fluorine.On a regional scale a relationship can be established between some of the ore deposits and important tectonic lineaments. The stratiform deposits preferentially occur within a calcareous-detrital facies located at the margins of basins. These basin margins are related to important synsedimentary faults.Fluorite is the only economic mineral in these deposits. Quartz, carbonates, barite and pyrite are common minerals accompanying fluorite. Other minerals that may occasionally be present as minor components are: marcasite, chalcopyrite, fahlore, sphalerite, galena and related supergene minerals."

Jan 1, 1994