Search Documents

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, W. L. Mason, John J. Justen

"A miscible displacement pilot, using a slug of LPG driven by separator gas, was conducted in the Cardium Reservoir of the Pembina Field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gas phase, an .experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to cakulate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones, and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in con-trolling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir."

Jan 1, 1960

By Peter A. Hacquebard

"Two continuous coal zones occurring in a 2500f t (762 m) thick section of the Upper Carboniferous Pictou Group (Westphalian C and D) have been encountered in five offshore wells drilled f or oil and gas in the Gulf of St. Lawrence. They correlate, by means of fossil spores, with thick coals of the Mabou and Inverness coalfields situated at the eastern margin of the Basin. Therefore, the presence of a large submarine coalfield of at least 18000 sq mi. (46 620 km'] is indicated. This compares with an estimated size of 14 000 sq mi. (36260 km' ) for the Sydney Coal Basin.Accessibility is provided only by the small onshore parts of the Mabou and Inverness fields, because farther offshore the coals lie too deep to be mined (below 4 OOO f t ([ 219 m)).Two near-shore coal exploration wells indicate that at Mabou Mines the younger Inverness coals occur at a mineable depth to at least 5 km from land. A structure contour map of this area shows a reserve of 125 million tons in two Inverness equivalent seams that are 8.5 ft (2.6 m) and 4.5 ft (f.4 m) thick. The Mabou coals, however, reach too great a depth close to shore to possess mineable resources.A structure contour map of the Inverness submarine area, based on mine data and one off shore seismic profile, indicates inferred mineable resources of 160 million tons, in two seams that are 7ft (2.1 m) and 4.5 ft (f.4 m) thick . A detailed deep seismic survey will be necessary to substantiate the structure and resource estimates"",Maceral and coal quality percentage diagrams of five column samples of these seams (the 7 Foot and 13 Foot Seams of Inverness Equivalents) show a bright banded coal, high in reactive macerals, which will produce a weak coke unsuitable f or metallurgical purposes. A thermal coal with a rank of H. V. ""B"" Bituminous (0.64% Ro) is present, averaging 12000 btu llb (6 660 kcai/kg), 10% ash and 6% sulphur, of which 60 to 80% is derived from pyrite.Microlithotype profiles of the major Mabou and Inverness coals show characteristic successions that can be used f or seam identification and proved valuable f or structural interpretations.The time of faulting in the major fracture zone on the eastern margin of the Gulf of St. Lawrence Basin has been deduced from coal rank variations. It occurred in pos tPermian, probably Early Triassic time."

Jan 1, 1986

By Guoqiang Lan, Jun Song, Bin Ouyang

Rare-earth pyrochlores, commonly exhibiting anomalously low lattice thermal conductivities, are considered as promising topcoat materials for thermal barrier coatings. However the structural origin underlying their low thermal conductivities remain unclear. In the present study, we investigated the phonon properties of a group of RE pyrochlores, Ln2Zr2O7 (Ln = La, Nd, Sm, Gd) employing density functional theory and quasi harmonic approximation. Through the relaxation time approximation (RTA) with Debye model, the thermal conductivities of those RE pyrochlores were predicted, showing good agreement with experimental measurements. The low thermal conductivities of RE pyrochlores were shown to largely come from the interference between the low-lying optical branches and acoustic branches. The structural origin underlying the low-lying optical branches was then clarified.

Jan 1, 2015

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By Habib Zughbi, Paul Zulli

"A key step towards sustainability in iron and steelmaking is to optimise the use of raw materials and energy consumption, and consequently minimise CO2 emissions. Models based on a Process Integration (PI) approach play a key role in evaluating various scenarios and the impact of introducing changes in raw materials and operational conditions on the overall energy consumption and CO2 emissions. BlueScope uses a PI based comprehensive model for its Port Kembla Steelworks (PKSW), called the Integrated Steelworks Energy and Emissions Model (ISEEM). ISEEM is tightly coupled to the configuration of PKSW. It is based on mass and energy balances as well as thermodynamic relationships. ISEEM is a steady-state model and is used to predict overall and detailed unit-by-unit energy consumptions and CO2 emissions. It is also used for plant-based scenario modelling. This paper investigates the impact of major changes to PKSW configuration, including the shutting down of a blast furnace and cokemaking battery, on the energy consumption and CO2 emissions of the plant. It discusses some of the issues involved in updating the model and some identified opportunities."

Jan 1, 2015

By J. C. Marchand, M. A. Berube

"L'objectif principal recherché lors du broyage d 'un minerai est de libérer adéquatement ses valeurs utiles en vue de leur concentration ultérieure. La pratique courante consiste à tenter d'obtenir un produit de broyage d'une granulométrie constante. Malheureusement, les propriétés texturales des minéraux utiles varient naturellement dans un gisement et une telle stratégie n'entraine pas toujours pour ces minéraux un degré de libération constant. Pour un rendement optimal du procédé de concentration, cette variable très importante doit donc être périodiquement vérifiée.Jusqu'à maintenant, la plupart des études de libération des minerais se font en examinant des sections polies de particules du minerai broyé. Le GRAAIM a récemment assemblé un système modulaire d'analyse d'images qui servira en grande partie à des mesures automatiques du degré de libération des minéraux. Le système s'avère relativement peu coûteux comparativement à la plupart des analyseurs de texture conventionnels si l'on considère que plusieurs de ses composantes, par exemple le miniordinateur, sont utilisées à une foule d'autres applications, et il permet de plus une grande souplesse d'utilisation puisque l'on a qu'à construire des algorithmes de mesure et de calcul en fonction de l'objectif recherché. Des programmes particuliers permettant des études automatiques de libération sur des sections polies de particules ont ainsi été élaborés. Ils permettent également des mesures de teneurs et de distributions granulométriques apparentes des particules. Des résultats obtenus dans le cas de minerais de fer sont brièvement présentés afin d'illustrer la technique."

Jan 1, 1983

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

By J. Budac, R. Kofluk, D. Belton, M. Sjogren

A series of tests were performed to determine the flammability limits of mixtures of oxygen, ammonia, steam and nitrogen, over a solution, in a sealed autoclave. The partial pressures of ammonia and oxygen in the vapour space were varied by adjusting the character of the solution and by adjusting the oxygen concentration in the oxidant gas respectively. The data shows that flammable conditions can be minimized by controlling the operating temperature, reducing the ammonia content in the solution, increasing the concentrations of Ni, Cu and Zn in solution and keeping the % oxygen in the gas phase less than 15.5. Observations were also made that suggest that the presence of an aerosol in the vapour space may hinder ignition.

Jan 1, 2004

By S. M. Bradshaw, E. Charikinya

"Microwave induced cracks have the potential to enhance metal recovery from coarse sphalerite particles in heap leaching operations by creating new crack surface areas for lixiviant and enhancing value mineral exposure. The mode of fracture and the extent of mineral exposure due to microwave induced cracks have not yet been investigated. The objective of this study was to determine the extent of particle damage and mineral exposure in microwave treated particles. This was done using X-ray computed tomography (XCT) and image analysis techniques. XCT analysis was conducted on small (–5+4.75 mm), medium (–16+9.5 mm), and large (–25+19 mm) sphalerite ore particles before and after microwave treatment (MT). Geometrical properties, such as volume and surface area of each mineral phase in each particle was determined from the XCT reconstructed images using VGStudioMax image analysis software. These geometrical properties were used to calculate the interfacial areas of sulphide mineral grains in microwave treated particles before and after MT. The ratio of specific interfacial area after MT to specific interfacial area before treatment was used as an indicator of the degree of preferential grain boundary fracture. The results showed significant grain boundary fracture after MT at all sizes. For small sized particles, about 31% of the interfacial area was lost compared to 23 and 16% for medium and large particles, respectively. The results also showed an increase in the degree of mineral grain exposure of 28, 26, and 15% for small, medium, and large particles, respectively, after MT. These results provide experimental evidence supporting improved mineral exposure due to MT. INTRODUCTIONFor some years it has been suggested that microwave treatment (MT) of ores might result in preferential grain boundary fracture that would have benefits such as improved grain exposure and particle weakening. (Kingman, 2006). Most of the experimental work investigating the application of microwaves to mineral processing flow sheets has focused on assessing the benefits of applying microwave technology to flow sheets consisting of size reduction and mechanical flotation cells (Kingman et al., 2004). Experimental studies have shown that coarse crushing during tertiary grinding of microwave treated ore resulted in a better liberated coarser flotation feed (Scott, Bradshaw, & Eksteen, 2008). It has been suggested that improved liberation in milled flotation feed, was due to the presence of grain boundary fracture in microwave treated particles. However, this improvement in coarse particle liberation does not necessarily translate to a significant improvement in downstream flotation recovery (Kobusheshe, 2010). This is as a result of the size limit to the flotation of coarse material, due to detachment forces acting on particle-bubble aggregates, which increase as the particle size increases (Jameson, 2012). Current conventional, mechanically agitated flotation cells are not designed to float coarse material (Jameson, 2012). Hence it has been difficult to show the downstream processing benefits of applying microwaves to ores processed by comminution followed by flotation (Kobusheshe, 2010). It is clear from investigations carried out so far that inappropriate downstream exploitation of microwave treated ore would fail to realise a meaningful process benefit (Kobusheshe, 2010; Ali & Bradshaw, 2011)."

Jan 1, 2016

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960

By M. J. Marinigh

Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable. In converting furnaces which have tuyeres such as the Noranda Reactor and the Teniente, Peirce Smith and Hoboken converters, efficient tuyere line management is critical to optimizing blowing rates, increasing refractory life, and improving safety. This paper will describe recent improvements made to equipment used for tuyere punching, tuyere silencing, tuyere pyrometry and refractory drilling of tuyeres and how the proper application of the equipment can lead to operational and safety improvements.

Jan 1, 2007

By C. A. Campbell

"There has been a significant reduction in maintenance hours and improved performance by maintenance crews at the MacLeod mine since the introduction of a Maintenance Control system which includes the use of maintenance standards. This paper deals with the steps taken to develop and implement the program. The objectives of the program and the organization and training of the control group are outlined. The work-order system, standards application, classification of work and the preventive maintenance procedures will be discussed.All maintenance information is processed on a Model 360-20 IBM computer, which turns out maintenance records and control reports for management action. Information in these reports, and reasons for reporting, will be discussed and the benefits resulting from the program reviewed."

Jan 1, 1973

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By J. W. Reynolds

Introduction The Sullivan mine, at Kimberley, B.C., is the principal source of ore for the Consolidated Mining and Smelting Company of Canada, Limited. Current production amounts to about 2,500,000 tons of lead-zinc ore a year. With approximately 1,600,000 feet of percussion drilling and 700,000 feet of diamond drilling being carried on each year, any improvements in drilling practice are important. Testing of new equipment and drill bits is a major function of the Testing Department at the mine. Tungsten carbide bits have been the subject of many tests since 1947 and have been used in operations since 1948. This paper details with the methods of testing and gives comparative data on performance and costs for tungsten carbide bits as compared to steel bits. Operational use of tungsten carbide bits started in April, 1948, and the extent of application has increased considerably since that time. The scale of employment is illustrated in Table I, which also shows other statistics on the use of carbide bits. Up to the present time eighteen types of carbide bits or tipped steel, as made by six different manufacturers, have been tested. In general, one supplier's bits have been used in operations, but some large-scale operational tests have been carried out with other types. The types tried are shown in Table II. To date they have been, the subject of 33 tests, covering the destruction of 804 bits over an observed footage of 42,586 feet.

Jan 1, 1951

By R. D. Brown

The first step in achieving a rationalization of Canada's crazy patch-work quilt of mining taxes and policies was achieved with the release last November of a major federal-provincial report on the taxation of the Canadian mining industry. The Report, prepared by a group of federal and provincial civil servants, sets out a concise and informative discussion of the major taxation and incentive issues facing the mining industry, and puts forward major recommendations for more rational and moderate taxation policies. It will be considered by federal and provincial Finance and Resource Ministers for possible action by the respective governments. The Report was prepared in response to a directive from the federal and provincial First Ministers in February 1978 to review the federal and provincial taxation of the resource areas. Although the Report is more successful in identifying problems rather than concrete solutions, and reflects some continuing differences of opinion between the governments involved, it does represent an important first step in a comprehensive review of our resource tax policies. This article summarizes the Report, which is some sixty pages in length. Although a detailed discussion of it is beyond the scope of this article, the report itself is recommended reading for those concerned about the current state of the Canadian mining industry.

Jan 1, 1979

By Michel Jébrak, Claude Bellehumeur

Abstract - Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont­ Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not defined by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis . The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

By Neville Jordison

Indirect, gravity flow, heat exchangers have become a well established technology in mineral and metallurgical process plants. The technology is a conventional heat exchanger using high efficiency plates, with a free flowing bulk solid on one side of the exchanger and a fluid on the other side. This simple concept leads to many opportunities for achieving greater energy efficiencies in process plants. Indirect heat exchange is much more efficient than direct heat exchange using air such as in a fluid bed or rotary device. When air is used directly, large fans are required, it may also be necessary to chill the air, both high consumers of energy. By contrast, using water as the cooling medium requires only low horsepower pumps, typically only 10% of fan HP. Furthermore there are no stack emissions with the requirement for removal of dust or emissions. Indirect heat exchange also creates the opportunity to recover energy. This can work in two ways: energy can be recovered from a hot bulk solid, to heat pressurized hot water for steam generation or preheat air. Alternatively recovered energy from elsewhere in the plant in the form of hot water, steam, air or thermal oil can be used to preheat a bulk solid.

Jan 1, 2011

By D. Yuan, M. Sitter, S. St. Jean, M. Collins

The Ambatovy Joint Venture comprises an operating lateritic nickel mine, ore slurry pipeline, pressure acid leach plant and nickel refinery in Madagascar. The hydrometallurgical process selected by Sherritt for treatment of the Ambatovy ore is a long-term, sustainable approach to producing nickel. Sulphur, used to prepare hydrogen sulphide, which is used to produce mixed sulphide intermediate, is recovered in the refinery as ammonium sulphate fertilizer. Additional sulphur is used to generate sulphuric acid for treatment of the ore in the high pressure acid leach (HPAL) step; fossil fuel consumption is minimized by using the heat generated from the exothermic reaction between sulphur and oxygen in the acid plant to produce power and steam. Steam consumption is minimized by design of efficient flashing and preheat systems for HPAL, while the high temperature of the HPAL step serves to minimize acid consumption. Fossil fuel consumption by the operation as a whole is further minimized by locating the leach plant and refinery near the port of Toamasina and utilizing a 220 km slurry pipeline to transport ore from the mine to the leach plant. In addition, Ambatovy has demonstrated a strong commitment to sustainability programs such as the biodiversity management program at the mine and local procurement in Madagascar. In this paper, the hydrometallurgical process for nickel and cobalt recovery from Ambatovy ore is described, along with highlights of Ambatovy’s approach to sustainability in Madagascar.

Jan 1, 2015

By P. D. Kondos, J. R. Goode

Given the global inventory of low grade and refractory gold deposits, processes that could turn these challenged deposits into mines are of considerable interest. Such gold deposits have low value and potentially high operating costs and so they pose special challenges for the mining engineer and metallurgist. Conventionally, refractory gold ores have been processed by whole ore pressure oxidation and roasting, or flotation followed by roasting, pressure oxidation or bio-oxidation of the concentrate. Halide-based processes have recently been developed that might be applied to concentrates. Low grade refractory gold ores have been processed using heap bio-oxidation followed by cyanide heap leaching or milling. Other processes are emerging. Barrick has completed an inventory of emerging technologies (1). A summary of the current status of these developments will be presented with the view that, with additional development, some of these technologies or a combination thereof may unlock the value of these deposits.

Jan 1, 2005