Search Documents

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By Norman O. Lotter, Dominic Fragomeni, Jorge Oliveira, Dee J. Bradshaw, Rebecca Monnapula

"The role of mixed collectors in enhancing the metallurgical performance of sulphide flotation processes was reviewed in 2008, and later published as an integrated theory by Lotter and Bradshaw, 2009. The theory proposed that xanthates, dithiophosphates and dithiocarbamates could be synergistically combined in an optimal formula to deliver improved grade and recovery. The approach uses a five-step structure, viz.1. A mineralogical study of the ore to be treated, identifying and quantifying the economic minerals (with hosting and association) and gangue species present.2. Selection of candidate collectors from this mineralogical information and from the known pulp conditions of that operation (e.g. Eh, pH).3. Design and execution of a factorial experiment to estimate and test the main effects and interactions, and to model the response surface for an optimum formulation [Box et al., 1978].4. Use of a High-Confidence Flotation Test platform in the factorial to reduce overall errors and allow for clearer observations [Lotter, 1995; Lotter and Fragomeni, 2010].5. Statistical design of a plant scale trial to measure and validate the gains [Napier-Munn, 1995; Lotter et al., 2009]. Eland Platinum, which was commissioned in November 2007, appointed a team to apply this theory to formulate an optimized mixed collector suite for use in the operation. The West Pit ore (UG2 - Normal ore) was sampled at site and brought to Xstrata Process Support, Sudbury, Canada, for mineralogical and metallurgical testing in 2008. Microprobe and QEMSCAN measurement characterized the type, grain size and textural association of the discrete Platinum Group Minerals (PGM) present. From the mineralogical data, it was clear that a mixture of dithiocarbamate and two xanthates would be a likely reagent suite selection. A factorially designed set of High-Confidence Flotation Tests studying these was performed, concluding that an optimal suite using certain amounts of these collectors was a viable formulation that would advance the grade and recovery performance at Eland above the standard PIBX by approximately 2.13% 4E PGE. The plant trial, which used a form of the replicated block design after Napier-Munn, 1995, and Lotter et al., 2009, exceeded this estimate with an overall PGE recovery gain of 2.48% (absolute basis) and a concentrate grade gain of 26.4 g/t PGE (absolute basis), as well as reducing chrome in concentrate from 2.04 to 1.62% (absolute basis). These gains proved to be statistically significant using the analysis of variance method, and have validated the theory."

Jan 1, 2011

By Lucas G. Thompson

My topic, "The Administration of Mineral Rights'.' is possibly an unusual one, as it deals with a subject upon which many of us have a more than passing interest, I thought ?it might prove consistent with the objects of this meeting, more especially as I propose to deal, not with those broad subjects of nation-wide importance which are often the subject'? of learned (and sometimes futile) academic discussion, but rather with problems in their practical light. To the scientist, the important question is What is it? to the technician, Can it be utilized? to the business-man, Will it pay? All three questions are important, and so quick has been the march of business on the heels of science? that the one question follows the other with astonishing rapidity and all three must be considered in the modern management of a mineral estate. A .good illustration of the force of this can be found in the recent advance of our knowledge of the element helium in which we have advanced from a solution of the first question to the last question in the short period of 55 years. It is to be borne in mind, however, that in the administration of mineral rights, the question "Will it pay?:' is of primary importance. What forms a mineral estate ? A former practice in western Canada in selling lands was to sell the hair with the hide. All transactions sold the lands in fee simple, which included all mines, minerals and rights and privileges whatsoever, excluding only the royal metals, gold and silver, which by imputation, though not by specific reference, in deeds. of title are reserved to the Crown. At that time the country was in the first ?stages of settlement and the value of our mineral resources was hardly appreciated and little understood.

Jan 1, 1923

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By B. Panton, J. Carvalho, E. T. Brown

High-capacity, post-tensioned anchors have found wide-spread use in initial dam design and construction, and in the strengthening and rehabilitation of concrete dams to meet modern design and safety standards. Despite the advances that have been made in rock mechanics and rock engineering during the almost 80 years in which post-tensioned anchors have been used in dam engineering, some aspects of the rock engineering design of high-capacity rock anchors for dams have changed relatively little over the last 30 or 40 years. This applies, in particular, to the calculations usually carried out to establish the grouted embedment lengths required for deep, post-tensioned anchors. These calculations which involve a number of aleatory and epistemic uncertainties, usually make simplified assumptions about the distribution and values of rock-grout interface shear strengths, the shape of the volume of rock likely to be involved in uplift failure under the influence of a system of post-tensioned anchors, and the mechanism of that failure. The resulting designs are generally conservative. These aspects of the rock engineering design of large, post-tensioned rock anchors for dams could be improved by making greater use of modern, comprehensive, numerical analyses in conjunction with 3D models of the rock mass structure, realistic rock and rock mass properties, and the results of prototype anchor tests in the rock mass concerned.

Jan 1, 2015

By B. S. Kim, Y. D. Kim, T. S. Kim, T. B. Kim, H. J. Chae

"The Nd-Fe-B scrap was placed in Fe crucible with pure Mg in an Ar atmosphere, and the scraps were melted using an induction heating method. The effects of experimental parameters such as melting temperature (range of 993K to 1073K) and holding time (15min-600min) on the ability of extraction were investigated. The microstructure and diffusion layers were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), and the constituent phases were characterized using XRay Diffraction (XRD). Diffusion of Nd through the Nd-Fe-B scrap into liquid Mg was described, and the diffusion coefficient of Nd in liquid Mg was estimated.INTRODUCTIONNd-Fe-B magnets are usually produced either from comminuted melt-spun ribbons as bonded magnets or hot pressed bulk magnets, or by sintering in conjunction with prior green compaction in an applied magnetic field (Sagawa et al., 1984). These magnets have been widely used for various electromechanical and electronic devices such as voice coil motors (VCMs) and magnetic resonance imaging (MRI) (Samardzija et al., 2012; Matsuura et al., 2006). The production of the Nd-Fe-B magnets is increasing by about 20% per year because of their excellent magnetic properties. However, the expansion of Nd-Fe-B magnet market induced a concern for the scarcity of Nd at the aspect of natural resource. Therefore, the development of an effective recycling process for Nd-Fe-B magnet scraps is an extremely important issue from the viewpoint of resource and energy conservation. Several recycling processes for the Nd-Fe-B magnets have been proposed (Uda et al., 2002; Lyman et al., 1993]. It has been reported that the best separation of rare-earths from the Nd-Fe-B magnets is obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. However, this process can make a large amount of waste water including dangerous solutions. Recently, (Xu et al., 2000) have reported a technique to extract Nd from 18Nd-72.4Fe-0.9B-1.82Pr-5.3Dy (wt.%) magnet scrap by using liquid metal extraction (LME) processing. However, these techniques seemed to be difficult for application, because the scraps consist of an infinitesimal amount of other minor elements (Pr, Dy, Cu, Al and Tb), and these minor elements can make a new intermetallic compounds with Mg. Also, some oxides or the plated Ni metal can be preventable to reaction between solid-liquid (S/L) interfaces. For these reasons, the substantive reaction mechanism between Mg and Nd-Fe-B scrap is not clear. In this study, the simple composition of 33Nd-66Fe-1B (wt.%) magnet scraps were prepared using an induction melting process. The effects of the experimental parameter on the diffusion properties between Mg and scraps were investigated to determine whether these methods could be used in industrial application in a liquid metal extraction (LME) process."

Jan 1, 2012

By J. T. Sims, C. E. Karayannopoulos

Today's rare earth industry is undergoing significant and rapid evolutionary change toward greater reliability and diversity of supply, increased security of supply chains, and better price forecasting. Technology innovation is reducing rare earth production costs while decreasing the impact of producers on the environment. Advances in rare earth material science are reducing the need for relatively scarce heavy rare earths (HREEs) in high-performance neodymium-iron-boron (NdFeB) permanent rare earth magnets and opening the NdFeB magnetic market space for a broader range of downstream applications. Rare earth producers such as Molycorp are increasingly able to offer long-term supply agreements with forward price predictability, something that has not been the case for many years. All of these trends are helping to restore the confidence of customers and other stakeholders in the rare earth space. That increased confidence is likely to bolster global demand for rare earth materials and expand innovative utilization of these remarkable materials.

Jan 1, 2014

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilisation to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilised to produce more effective dispersant systems which allow the preparation of, added value, higher solids and finer particle size calcium carbonate slurry products.INTRODUCTIONConcentrated aqueous dispersions of fine, particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently more than 10 million tonnes of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e. its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximise the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimise drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it' is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924

By M. Yamine, R. J. Ring, D. J. Waters

"An experimental program has been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid as an alternative oxidant to pyrolusite in the leaching of uranium ores from the Alligator Rivers region of northern Australia. Batch leaching tests on Ranger, Nabarlek, Koongarra and Jabiluka ores showed that uranium extraction was unaffected by choice of oxidant, but that Caro's acid reduced acid requirements by 15 - 25%. Lime requirements for neutralization of tailings liquors were reduced by 20 - 30%.The batch studies were extended to a four-stage continuous leaching circuit with a capacity of 400 gore h-I. Comparative leaching tests confirmed the reagent savings obtained in the batch tests. Following these encouraging laboratory results, lnterox Chemicals Pty Ltd carried out plant trials using Caro's acid. Reagent savings in the mill were similar to, or better than, those obtained in laboratory test work. The trials also established that Caro's acid has a number of operational advantages over pyrolusite.IntroductionUranium is most commonly extracted from its ores by leaching in sulphuric acid. Simple hexavalent uranium oxides and compounds are readily soluble but uranium in the tetravalent form is insoluble and must be oxidized for dissolution to occur. The most commonly used oxidants have been sodium chlorate and manganese dioxide. They act indirectly by maintaining iron as the ferric ion which oxidizes uranium by a surface electro- chemical reaction. An Fe3+ concentration of about 1 - 2 g L-I is usually considered adequate for the effective dissolution of uraninite(1)."

Jan 1, 1984

By J. Aiello

"A brief history of previous mining activity on Coal Mountain, near Corbin, British Columbia, is followed by a description of the steps leading up to the resumption of mining in /974 by Byron Creek Collieries. New developments, including a preparation plant, a rail spur and a totally enclosed facility, as well as operating techniques, are also discussed. IntroductionThe Corbin Mine of Byron Creek Collieries Limited is located in southeastern British Columbia, approximately 110 air miles southwest of Calgary (Fig. I), 15 miles south of Highway 3 via a newly constructed provincial road (Fig. 2). Development of the area began on July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J . Robert s, first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co. , after acquiring 15,000 acres of land in the area , began to develop a mine.F.J. Roberts was responsible for the construction of the 14-mile rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production.The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3), and production from 1908 to 1930 inclusive totalled 2,337,800 tons. This production was allocated to the mines as shown in Table 1. No.3, 4 and 6 mines were operated intermittently from 1931 to 1935."

Jan 1, 1980

By The Hollinger Mill Staff

ALTHOUGH cylindrical grinding mills have long been used, there is wide divergence of opinion as to what constitute best operating conditions. Questions such as mill diameter, diameter-length ratio, revolutions per minute, type and size of grinding media, volume of charge, circulating load, pulp level, pulp consistency, liner design, and size of feed, have all been given serious consideration by competent scientific investigators as well as by operators. While many laboratory and plant tests have been made that would seem to justify certain definite conclusions, there is a dearth of definite data giving actual results obtained when a grinding mill working between fixed limits is operated at its maximum capacity under varying conditions as to ball load, circulating load, speed, etc. In tests conducted recently at the Hollinger, extending over a period of thirteen months, to determine the best operating conditions for a ball-mill 6 ft. 6 in. diameter inside the liners, some very interesting facts have been ascertained. This paper is presented in the desire to make public the results of these tests and not with the idea that the last word has been spoken in regard to grinding. We feel, however, that these facts justify certain definite conclusions and hope that, by the fullest and frankest criticism and discussion, the essentials necessary for the correct design and operation of grinding mills will become better known.

Jan 1, 1937

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By J. A. Finch

In this paper, the author offers a personal view of what the next 30 years holds for mineral processing. Restating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining ?mineral processing ?extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro- and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but this author anticipates that the new lines will come from the waste management business. The paper concludes with the examination of the “research cycle” and identification of growth in small “high tech” companies and university research centres

Jan 1, 1998

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By J. H. H. Chamberlin

"In the Introduction the author briefly discusses the company history as it relates to the development of its contracts with the Japanese steel mills. The main part of the text describes how Coleman Collieries Limited approached the problem of mining coal profitably in thick, steeply inclined seams. For many years a basic room-andpillar system was worked by conventional methods. Main roadways were driven on strike across the mineable area. These roadways acted as haulage routes for coal, materials and men. Rooms were developed to the rise of the main haulage route by pairs of men using air-operated hand picks. As these rooms advanced the miners would lay and extend a sheetiron chute down which mined coal would gravitate to a controlled loading point, where it was loaded into trains of mine cars. Connecting roadways or ""OFFS"" were driven at predetermined intervals between adjacent rooms, forming pil1ars or blocks. Extraction of the blocks followed on a line conducive to good strata control some distance behind the developing rooms. A need for higher productivity, expansion of the operations and a scarcity of qualified miners resulted in the company deciding to mechanize its underground mines. Joy 6 CM continuous miners and 10 SC shuttle cars were selected as being machines that could reasonably negotiate the problems associated with the pitching seam. The equipment, nonetheless, has definite limitations and Coleman therefore developed a modified version of the room-and-pi11ar system such that the miners and cars could work on cross pitch. In the area described, main roadways were driven to the rise on an average gradient of 12 degrees. Panels, which consisted of two parallel roads with interconnecting cross-cuts, were then developed on strike to a boundary point. Blocks formed in the development of the panels were subsequently extracted on retreat. Problems associated with each phase of the operation are thoroughly discussed, together with roadway support methods and equipment used for the conveyance of coal and materials."

Jan 1, 1972

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By Jochen Franke, Derek D. Lichti

"This paper gives a brief introduction and presents recent enhancements in the MillMapper technology developed for thickness gauging and condition monitoring of liners in grinding mills used for mineral comminution. It also introduces the recent expansion of MillMapper functionality aimed at mill operational optimization. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces at feed, shell, and discharge ends with millimeter accuracy. Data capture takes nominally 5 minutes, hence interruption to mill operation is negligible.The paper is structured as follows. First, a review of the technology and discussion of recentlyimplemented innovations such as liner change out forecasting, automatic ball charge volume and weight measurement, and automatic mill liner volume/weight measurement for mill operational control or load cell calibration are presented. Combined weight information provides control over load related issues such as load fill levels for relining, or start-up load after reline. Feature descriptions are followed by a listing of the numerous advantages over existing techniques and the benefits to operations. Results from the application of MillMapper are presented throughout.INTRODUCTIONThe need for thickness gauging of liners of grinding mills used for mineral comminution is well known but the task is rarely completed to a satisfactory standard. Liner failure resulting from excessive wear can have expensive consequences. Furthermore, mill performance as well as liner wear are known to be correlated to lifter bar geometry (Napier-Munn et al., 1999; Rajamanni et al., 2005). At present, the following techniques are routinely used to gauge the thickness of mill liners:1. Visual inspection;2. Ultrasonic thickness gauging (for steel liners); and3. Physical inspection (e.g. nail inserted in rubber liners)"

Jan 1, 2008