Search Documents

The first geological maps of parts of Australia were produced in the 1830s and 1840s, many being for purely practical purposes, such as indicating the occurrence of coal, iron and other essential materials. Mineral location maps were also first made about the same time.More systematic geological mapping commenced in the 1850s when large parts of New South Wales and Victoria were studied in government-sponsored surveys by geologists such as Samuel Stutchbury, Alfred Selwyn and Reverend William B. Clarke. Their work coincided with the opening up of most of the major goldfields of eastern Australia, which led to the establishment of Departments of Mines in the separate Colonies (later States within the Commonwealth of Australia).A few companies employed consultant geologists at this time, and the mapping by Frederick Odernheimer is particularly notable. Geological study of Australian ore-deposits and mineralisedareas was influenced by the continental European geological ideas of men such as Odernheimer as well as by those from England. Both geological and mineral maps were a feature of Colonialdisplays presented at major international exhibitions during the second half of the nineteenth century. The maps accompanied rock and mineral collections which showed the known and potential mineral wealth of the Colonies. Such displays raised interest in the potential for development amongst government officials, entrepreneurs and investors in Australia and abroad.By the 1880s most of the Colonies had produced basic geological maps, and several maps of the whole continent had been published. Although systematic mapping of the continent become a reality only in the 1950s, the nineteenth century geological and mineral mapping formed the basis for the development of the major coal, artesian water, and metalliferous mining regions of Australia.

Jan 1, 1990

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

By C J. Stanley

Reflected light optical microscopy, or epimicroscopy, is one of the oldest techniques of modern mineralogy. At a relatively low capital cost, it is also very resourceful, and the analytical choice for the identification of most ore minerals. In ore mineralogy, reflected light optical images have the potential to overcome the main limitation of backscattered electron images from scanning electron microscopes, namely contrast of mean atomic number  below the spectral resolution of the backscattered electrons detector. This is the case for relevant ores, like iron (haematite-magnetite) and copper-zinc ores (sphalerite-bornite), but for both cases the pairs of minerals are easily discriminated in reflected light. The improvements in optics and electronics also made microscopy a powerful source of digital images, suitable for automated analysis for minerals processing, as the determination of liberation spectra. The drawback, however, has always been the impossibility to recognise the transparent minerals, which account for most of the gangue phases in ores, from the embedding resin, usually epoxy. In order to determine if there was any possibility to separate quartz from epoxy resins, reflectance spectra have been acquired for quartz and some commercial epoxy resins (Araldite, BuehlerÆs Epothin and Epocolor, Araldite spiked with fluorochrome from Struers), from 380 to 720 nm in 5 nm intervals. Reflectance of quartz and epoxy is very similar over the whole visible light range, and varies from 4.5 to five per cent. Epocolor, a red-dyed epoxy, reflects slightly more above 560 nm, as does Araldite spiked with the fluorochrome from 460 to 570, but for both the reflectance is still very close to that of quartz, under 5.1 per cent. This data set is final, and precludes the application of reflectance in light optical image analysis for assessment of liberation, phase quantification, or any other signal that requires separation of resin from transparent minerals.

Jan 1, 2008

The paper deals with the taking of soundings in connection with coal mining operations under part of the Pacific Ocean adjoining John Darling Colliery.INTRODUCTIONIn the early days of mining in the Newcastle District there did not appear to be any definite law specifying the limits to which mine workings, other than certain borings, could extend under tidal waters.As time went on, a figure of 120 ft. was fixed as the minimum thickness of strata between the roof of the seam and the sea bottom; beyond this mining operations are disallowed. The laws relating to working coal under tidal waters are as follow:-The minimum width of pillars to be left shall be eight (8) yards and the maximum width of bords or other excavations shall be six (6) yards, but the lessee may at his discretion increase the minimum width of the pillars or decrease the maximum width of the bordsor other excavations so as to increase the general safety.The eight (8) yard pillars shall be left unwrought.In on-road of every pair of Winning-off or leading headings, a bore shall be kept going ten (10) feet in advance for the purpose of foretelling the presence of any fissure, wash-out, open joint, fault, dyke, or otherwise, and all winning-off headings shall be driven atleast one hundred (100) yards in advance of the working bords.The most accurate and trustworthy information shall be obtained by the lessee not only' of the depth and character of the ocean bed, river, lake, or estuary deposit, but also of the strata overlying the coal seam.When working under the ocean, strata shall be bored through and proved a minimum thickness of thirty (30) feet at the face of the leading headings or levels immediately such headings or levels are under the ocean, and...

Jan 1, 1947

By Ketelaar P. B, Nichols S, Power W. L, Utley D. C

The impact computers are having in geoscience is distinctly mixed. In the petroleum industry where much of the data are based on geophysics, computers have become an integral part of exploration and reservoir evaluation and simulation. In the minerals industry, the trend to computerisation is more advanced in some disciplines than others. Geophysical and remote sensing data are routinely processed and imaged using state of the art computer techniques. Mine surveying, planning, design and resource and ore reserve estimation are now all predominantly reliant on computers. However senior management of many companies, particularly in the mineral exploration industry, are still reticent to fully embrace the technology. 3D computer modelling of geology and orebody delineation is still largely in its infancy. Two current and significant drawbacks to the routine use of computer modelling of geology in both mining and exploration are the tedious and time consuming modelling process and the lack of seamless interaction between 3D computer-aided drafting (CAD) software and geographical information systems (GIS) which are largely 2D in their data treatment. There is an urgent need for a 3D spatial information system (eg 3D GIS) with intelligent and rapid modelling functionality. One of the keys to the successful building of 3D geological computer models begins with data base structure and design to ensure that there is no loss of data fidelity through data capture, storage, manipulation and modelling. Once a model is constructed, the latest generations of visualisation software provide sophisticated environments over a range of hardware platforms for visualisation in both mono and stereo viewing. This is demonstrated by the geological models which are presented in the digital interactive version of this talk whose URL on the World Wide Web is: http://www.ned.dem.csiro.au/FRACTAL/pubs/talk97AUSIMM/

Jan 1, 1997

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

Presidential Address Today I want to couple that prediction with a discussion on competitiveness and changing employment roles in our industry. A crude analysis of the intensity of use of metals in developed and undeveloped nations was undertaken by dividing the weight of copper, zinc, lead and aluminium used in countries by the population. In the developed countries which were basically the Western European States, USA, Canada, Australia and Japan, approximately 38 kilograms are used per annum. In the developing countries which were basically the South-East Asian country Korea, India, Pakistan and Taiwan, the usage is 5.3 kilograms. Thus, if the developing world is to catch up with the developed world, the intensity of use of metals will have to increase seven times. The usage of metals in the developed world is increasing at the rate of 1.5 per cent per annum while the rate of increase in the developing world is about 5.8 per cent. In this analysis, the population of the developed world was 850 million and the developing world 1.5 billion. Note that this analysis did not include Russia, China and most of the countries of South America and South Africa. I am sure that with time, these undeveloped countries will move into the developing category. In the long-term there is obviously great opportunity for us both in the primary and secondary processing required to meet world demand. Turning now to competitiveness and changing employment roles. I am sure that everyone here present is aware of the urgent need for Australia to improve its competitiveness. I want to try and relate unionism and industrial relations, management and tertiary education to our competitiveness. I wish to talk on these items as I see them in the past, the present and the future. So firstly unionism and industrial relations. It has been unfortunate for Australia that unionism was based on the United Kingdom craft system. It is not surprising that it was because UK has been the basis for almost ' all of our institutions and that has generally been of very great value to us. The craft system in our trade unions has lead to the demarcation problems of which we have all been well aware. This has been extremely limiting to the individual; it has limited his or her ability to broaden their scope of knowledge and far worse it has limited their ability to maximise their satisfaction at work as they have only been able to undertake part of a job, rather than being able to undertake a role in totality.

Jan 1, 1992

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

-in 1961,.West Australian Petroleum's Eneabba. No. 1 bore encountered twenty-two' seams of coal totalling forty feet in thickn' ss between the..'depths of 6373 feet and 64,/,1 feet. 0n'ana:lysis; this coal had a. similar calorific value (8000 - 9000 B.

Jan 1, 1964

Sustainable development places a heavy burden upon everyone involved in the public policy debate, about how to balance economic growth and environmental protection. We must treat that responsibility very seriously indeed. The mining industry especially cannot dodge the responsibility, even if it wished to.

Jan 1, 1992

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

By J Nantel

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

By D McInnes

Rather than look at the problems associated with sampling, this paper deals with the issue of sampling and blending to optimise revenue û predominantly in the mining industry. An example of the use of this methodology in the agriculture industry is also presented. Mining companies, in particular, are experiencing a boom in commodity prices and many believe the industry is in the middle of a æsuper cycleÆ. Production levels are being escalated dramatically to meet the demand coming from China and India. This in turn has further stretched the capacity of our rail and port infrastructure û resulting in significant shipping queues around most Australian commercial ports and increased demurrage costs for the producers. Mining companies are now looking for effective scheduling, planning and blending to maximise production and reduce demurrage charges û given the current infrastructure constraints. Mining companies can no longer use spreadsheets to run their business. This paper further looks at how these outcomes can be met by optimised blending using an integrated supply chain management system such as MineTrak together with effective sampling and analysis.

Jan 1, 2005

By T P. Tafirenyika, K C. Corin, C T. O’Connor

There is a growing demand for copper driven by its applications in renewable energy and electric vehicles. Sulfide ores are an important source of copper. Flotation is a critical front-end process used to remove gangue minerals and concentrate the copper minerals. The electrochemical activity of sulfide minerals contributes to their overall activity in the flotation pulp. The mineral rest potential dictates how collectors interact with the mineral surface, and hence ultimately on the flotation response. Dissolved oxygen, (DO), pH, redox potential (Eh) and water composition and ionic strength are also significant in controlling flotation performance. The aim of this investigation was to determine the influence of the electrochemical environment both during milling and flotation on the flotation behaviour of bornite and chalcocite. For this investigation, the interactions of collector with bornite and chalcocite were studied using synthetic plant water (SPW1) and deionised water (DIW) at 5 different pH levels. Sodium isobutyl xanthate (SIBX) was used both in microflotation, collector adsorption and zeta potential tests.

Aug 24, 2022

The Golden Cross is the first large precious metals mine to be both commissioned and closed in the æmodernÆ era in New Zealand. This paper discusses the life cycle of the Golden Cross mine, with emphasis on the closure process and post closure management.   The closure process has generally been very well managed, and successful, but in spite of that some on-going issues remain unresolved. Nearly nine years after the end of mining the mine owners are still actively managing the site, with no immediate end to that in sight.   The site has been described as atypical, due to the identification of a deep seated landslide below the tailings and waste rock storage facilities. However that should not be given too much emphasis when addressing the overall closure and post-closure management issues, which could well apply to other existing and future mine sites in New Zealand.   The Golden Cross can provide valuable lessons for other miners, and the issues arising at this site should be watched closely by the industry as a whole.

Jan 1, 2006

By Sorokin AP

The main regularities of the tectonic history of the Circumpacific belt's Asian segment are discussed. The established longitudinal metallogenic zoning is characterized by essential copper specialization being replaced in the.continentward direction by tin-tungsten and then by copper-gold-molybdenum and-tin-lead- zinc ones. The zones indicated show specific magmatism and ore forming fluid composition. The eastern margin of Eurasia experienced specific tectonic history and exhibits a wide variety of mineral deposits. It is composed of the Siberian and Sino-Korean cratons and of the largest mobile elements of tectonosphere like the Hyperborean, Urals-Mongolian, Mediterranean and Circumpacific belts. The Earth's Atlantic segment mobile features show deep penetration of their geosyncline-fold systems into the eastern margin of Asia. A good example is the Urals-Mongolian belt, its Intra-Asian branch being located within the continental margin. The Intra-Asian structural features have WE and NE trending, while folding process moved southward : Karelides and Baikalides are found in the Transbaikalia and the Soviet Far East (Stanovoy, Bodaibo-Patom, Baikal- Vitim, Selenga-Yablonovy fold regions)

Jan 1, 1987

By Muir DM

In recent years, significant improvements have been made in the design and operation of carbon-in-pulp plants. Some of the major developments in plant operation and technology are reviewed together with an outline of the research being undertaken in Western Australia. The main problems facing operators include the understanding and control of carbon fouling and regeneration, and the recovery of gold from the carbon. It is shown that carbon fouling by a variety of agents, particularly cyanide, calcium carbonate and silica, cause a significant loss of kinetic activity which in turn leads to poor plant performance. The importance of acid washing and adequate thermal reactivation is discussed. Although the Anglo elution procedure is commonly used in South Africa its use in Australia in preference to the conventional Zadra elution procedure is likely to be re- stricted because of its demand for high quality water. Solvent elution by the recently developed Micron procedure using refluxing methanol, ethanol or acetonitrile vapours is an attractive alternative. This elutes gold in 4-6 hours and provides concentrated gold solutions suitable for simplified gold recovery steps.

Jan 1, 1984

There is an established need for an inflow of foreign capital if New Zealand is to meet projected growth rates. The Government recognises this and encourages capital inflows especially where there are allied economic benefits such as the access to specialised know-how or export markets. The Government has promulgated certain Regulations which are administered by the Reserve Bank. Under the Capital Issues (Overseas) Regulations 1965, consent is required before any company incorporated overseas can commence business in New Zealand or before an overseas person can borrow or raise any money in New Zealand. A New Zealand company is deemed to be an overseas person if more than 25% of the voting power is held by non-residents. In terms of current policy, overseas companies are permitted to borrow in New Zealand only a limited amount of working capital and some longer term capital calculated on the ratio that their New Zealand owned equity capital bears to their overseas owned equity capital. Wholly owned overseas companies are expected to bring all of their Fixed term capital from overseas.

Jan 1, 1971

As this Seminar is on "Progress - Mining and the Environment", I am taking the liberty of extending my address beyond the scope implied by the subject, "Rehabilitation of Mined Land", with a preliminary discussion on broader economic issues relevant to "Progress and Mining in Western Australia" before discussing its effect on the Environments Western Australia is nearly one million square miles in area and has a population density of approzimately one person per square mile. Because of its vastness it has wider climatic variations than any other Australian State. The north is tropical and the south is in the temperate zone. The major portion of the State is an arid plateau with less than 10 inches of mean annual rainfall. The climate, rainfall and soil conditions of the South-West region are more favourable to agriculture than any other part of the State and consequently was settled first. The immediate need of the colonists being food and shelter, the early economy was based on farming and forest products.

Jan 1, 1971

The constraints in university courses are lack of hours, high cost of scientific equipment, and poor availability of suitably experienced staff. These have forced the balance away from practical work and towards more theory. Labelling of individuals as either practical, or academic, does not help the inter- change of staff between industry and univer- sities that is necessary to balance idealism and realism. Practical men who do return to universities may lose seniority and find that industry is reluctant to have them back. Academics who specialise too long may concentrate on their research to the exclusion of basic material. It is difficult to operate pilot scale plants in universities because of lack of time, and obsolescent equipment. Small grants from industry might enable tests to be run in research laboratories such as at C.S.I.R.O.. Within universities there may be a need for greater interchange of students among depart- ments, aided by the absence of weighted student unit measurements, as suggested by Aus.I.M.M. and A.M.I.C.

Jan 1, 1984