Search Documents

By S Grano, M Fordham, H Manouchehri, J Curral

This paper focuses on the impact of high pulp temperature on sphalerite flotation after the zinc regrind circuit in the Zinc Plant of Somincor, owned and operated by Lundin Mining Corporation. In the zinc circuit, the zinc rougher concentrate is reground with forged steel media before flotation with one stage of roughing and scavenging, and three stages of cleaning to obtain a zinc final concentrate (zinc grade >50 per cent). After regrinding, sphalerite flotation has been found to be seriously affected by high pulp temperature which may occur during the summer months. Mineral recoveries were found to be seriously reduced at pulp temperatures above 60¦C. At this high pulp temperature, neither elevated copper sulfate concentration nor a decreased pH alone appreciably increased Zn recovery. However, a combination of these two (eg a decrease in pH from 11.5 to 10.8, and an increase in copper sulfate dosage from 400 g/t to 800 g/t) was found to reduce Zn depression at high pulp temperature. At pulp temperatures below 45¦C, the negative influence of pulp temperature on mineral recoveries was minimal. A systematic series of flotation tests and solution/surface analyses were performed to reveal causes for poor sphalerite flotation at high pulp temperature after regrinding. The decrease in mineral recovery was shown to be associated with variations in the surface species on mineral particles in response to the increased pulp temperature. These variations in the surface species include collector desorption and superficial oxidation to form lead/zinc oxide/hydroxides on mineral particles. The influence of the type of regrinding media on sphalerite flotation at high pulp temperature was also addressed in this work.

Jan 1, 2008

North Broken Hill Limited came into prominence as a producing mine at· the commencement of the present century, when a great many of the disabilities experienced in earlier mining operations th:rough lack of adequate stope filling had been overcome.The northern or narrower ore-body was first mined in the upper levels and, in the early stages, no great difficulty in mining was experienced. In depth, under the influence of its northerly pitch,. the wide southern ore-body entered the North mine between the 400 and 500-ft. levels. Owing to its flat dip and the relatively weak nature of the hanging wall and footwall, the value of close filling was recognized and this policy has been followed throughout the life of the mine. This feature undoubtedly contributed to the freedomfrom "creep" action to which some of the older mines had been subjected.The Broken Hill lead-zinc-silver ore-bodies occur as well defined replacements of favou:rable horizons, in intensely folded Pre-Cambrian sedimentaries. In the North mine two main replacement zones occur, the Gre being found where the beds are involved in a certain set of minor folds. The resulting ore-bodies are roughly elliptical in cross-section, the long axis of one being north-east of, and somewhat offset from the long axis of the other. The ore-bodies pitch eastwards at 40° and dip northwards at 60° in a fairly regularmanner. The southern Ore-body has an average length of 700 feet and an average width of 90 feet with a maximum width of 230 feet, whilst the nonhern ore-body on the lower levels averages 500 feet long and 40 feet wide.

Jan 1, 1940

Evidence for Middle-Late Triassic large-scale, silicic volcanism characteristic of extensional continental terranes is widespread in the Tasman Orogenic Zone in Eastern Australia. Detailed study of an area of south-east Queensland has defined the eroded remnants of a large collapse caldera and an associated area of rhyolite dome building and regional downsag which may be a second caldera (Stephens, 1986). The silicic volcanics and minor basaltic to andesitic products have been assigned to the Aranbanga Volcanic Group (Cranfield, in prep.) and the associated granite complex has been named the Mungore Complex (Ellis, 1968). Published isotopic age dates on the Mungore Complex are 212-219 m.y. (K-Ar Biotite; Ellis, 1968) and 226 m.y. (pooled Rb-Sr on several similar plutons in the region; Webb and McDougall, 1967). Basalts within the area have been dated at 219 m.y. (GSQ Annual Rpt., 1986). The collapse caldera (Mungore Caldera) lies on the intersection of 4 major structural features: 1) the Mt. Perry Lineament, a meridional fault zone extending for over 600 kilometres in a NNW-SSE direction and which has faulted the eastern part of the caldera 5 kilometres sinistrally. The lineament has been active at least from mid-Permian to Late Triassic and has localised activity into the Tertiary. Granite plutons of the same age as'the Mungore Complex- are topographically prominent and largely concentrated east of the Mt. Perry Lineament and its extensions (Nash, 1986); 2) the extension of the Darling River Lineament, a continental-scale, ENE trending feature which correlates with regional structural discontinuities but which lacks expression as faults within the Tasman Orogenic Zone;

Jan 1, 1987

By P J. Mathew

Quality and process control in the iron ore industry is based on measurements of ore grade from blast holes through to shiploading. Traditionally this has been carried out using conventional sampling, sample preparation and analysis methods, but on-line analysers are now being introduced for monitoring the grade of important process streams. Once a conventional sample has been collected, it can be analysed for a wide range of elements. On the other hand, on-line analysers measure only a few selected elements, but they provide rapid feedback on grade, which is important for effective quality and process control. In both cases, the linkage between mining, processing and final blending operations at the port is crucial to ensuring that product quality is maintained while production targets are met and the life of the resource is maximised.

Jan 1, 1998

Self Advancing or "Poweredtt supports are a successful means of supporting roof and designs have reached the stage where adequate support capa- bility is available for all conditions. Some designs have resulted in equipment being too difficult to transport underground and too complex to maintain. Current trends are reducing those problems and simplicity in hydraulic systems is now the keynote of both supplier and user. There is a good possibility that the "Shield-Chock" support will be the universal design of the future. So-called t'shortwall supports" have been developed to the point where they can be applied with a high degree of confidence to conditions of great variety. Develop- ments by manufacturers and practices of users related to maintenance should result in consistent achievement of designed performance.

Jan 1, 1974

A number of small copper deposits occur in the Pernatty Lagoon-Mt. Gunson area. Textural and mineralogical differences distinguished the lagoon sulphide deposits, which occur in a water filled basin of permeable bedrock immediately under the lagoon floor, from the largely oxidized deposits which occur in the low hills adjacent to the lagoon deposits.Groundwaters are carrying copper, and to a lesser extent zinc, downstream to the lagoon. Several species of sulphate-reducing bacteria are widespread in the groundwaters and lagoon muds.It is suggested that copper sulphides were first deposited at the same time as, or soon after, the host Proterozoic sediments, and that during the present cycle of erosion the lagoon deposits may have been enriched, or largely formed, by bacterial precipitation of copper sulphides from laterally migrating cupriferous groundwaters.

Jan 1, 1971

Of the energy resources present in Australia, coal and uranium are by far the largest. These two resources ap- pear sufficient to satisfy Australia's energy needs beyond the immediately foreseeable future and long after the natural petroleum resources are exhausted or have ceased to play a significant role. By that time, coal could be converted in plants of very large size to synthetic liquid and gaseous fuels which will be used as substitutes for pet- roleum fuels, particularly for transport. The basic role of uranium will be to supply electricity from nuclear power stations for heat and power requirements, thereby freeing non-coking coal largely for conversion purposes. The establishment of these enterprises will require a massive national effort and a high degree of co-ordination at the planning stage.

Jan 1, 1975

By Hughson B

The need to prevent the sterilisation of coal stems directly from the fact that it is a non-renewable resource. In N.S.W. a vast amount of coal resource is located under major public utilities such as freeways, railways, stored waters, pipelines carrying gas, water and sewage, and transmission lines. Total extraction has occurred under freeways, transmission lines and pipelines with little or no damage. Where damage has resulted, the cost of restoration was only a small fraction of the value of the coal recovered. However, coal at present is being sterilised and perhaps lost for ever under stored waters and railways. If engineering solutions are available for mining under these improvements economically and with maximum safety, then coal should be extracted and utilised to the benefit of the State.

Jan 1, 1986

A novel problem-solving exercise for undergraduates is described which is directly relevant to production supervision. It is based on the fictitious Metwin Plant which produces refined metal from sulphide concentrates via a hydrometallurgical route with six unit operat- ions. Students are given details of the chemistry, process engineering and normal operating conditions. They are also given min- imum data for the Plant when it is operating with a fault. By requesting further data, for which they are 'charged', the students must diagnose the fault. The responses of students to the exercise are described. The data were produced by computer simul- ation of steady state operation under normal and various faulty conditions. The development of this program was an educational experience for the author and it stimulated new interest in metallurgical process engineering.

Jan 1, 1984

By Belcher C. B

A simple gravimetric procedure was developed for the rapid determination of carbon dioxide in coal mine roadway dust samples and the result is used for the subsequent calculation of incombustible matter contentaccording to the requirements of the Queensland Coal Mining Act. The carbon dioxide is determined through loss of mass by a semi-enclosed apparatus, following room-temper.ature hydrochloric acid attack on the sample.With a sample containing 36 per cent carbon dioxide, the achieved standard deviation (ls) of 0·3 per cent CO. is adequate for coal mine roadway dust analysis.This simple procedure enables relatively unskilled labour in mine laboratories, to analyze coal mine roadway dust samples in accordance with the Act. Some 50 analyses can be achieved per day compared with 8 by the Australian Standard Method for coal.

Jan 1, 1976

By Mills JC, Belcher CB

X-ray fluorescence spectrometry is used videly for routine quality control of the mining, )lending and agglomeration of iron ores. Most )f the procedures used, cannot tolerate significant changes in matrix composition or be Lpplied to a wide range of elements. Accord- ngly, a graphite briquette technique which is Lpplicable to some fifty elements in widely Tarying iron ore matrices is described. The ignificant advantages are suitability of the ame preparation for both optical emission and -ray spectrometry, a complete elemental overage for the range 5bcg/g to 100%, and the recision and accuracy of the methods are om.parable with the standard chemical.methods hich have been superseded in the authors' boratories. The proposed methods become ore attractive and economical as more prehensive information is sought.

Jan 1, 1975

By T C. Hughes, R Hughes

Ausmelt has developed and commercialised high temperature reactor technology that has been applied to waste processing in the form of a catalytic waste converter (CWC). Ausmelt Technology uses a top submerged lance system within a versatile converter containing an oxidised molten siliceous slag. Metals and other valuable products can be extracted from wastes for recycle into the community. Non-valuable components such as toxic organochlorinated compounds are destroyed and prevented from reforming. The slag produced is inert and can be safely used in building and concreting. The CWC can be applied to practically all types of wastes and examples from Ni-Cd batteries to toxic wastes are discussed. Additional benefits can be derived from large-scale operations if the surplus heat generated is exploited to produce steam and electricity.

Jan 1, 2000

Members of The Australasian Institute of Mining and Metallurgy are engaged in locating, extracting, processing, marketing and converting the worldÆs mineral wealth for its consumption in a useful form. We have an ethical responsibility as professionals to carry out our roles in such a way that we seek to optimise the recovery of that wealth for the benefit of the community, not only now, but also in the future. To be able to optimise, we must be able to measure with confidence the value of the commodity through the various stages of treatment from discovery of a geological anomaly to the end use. This introductory paper will provide an overview of some aspects of the issue, including the possible extension of the coverage of The InstituteÆs Codes to production accounting and reporting.

Jan 1, 2002

The radiolarian biostratigraphy of the western part of the Gympie Province, north of Brisbane, has been examined. This part of the province comprises mainly the Amamoor beds and the Gympie Group, which have been assigned Permian ages on the basis of localised marine macrofossils. This study has shown that the Amamoor beds and the Gympie Group include older strata than previously supposed.The Amamoor beds consist of at least two tectonic units, namely a melange unit (unit A) and a well stratified sequence of sedimentary rocks (unit B). The former unit, regarded as an accretionary subduction complex, contains chert blocks ranging from Late Devonian to Earliest Carboniferous, while the latter unit yields Permian radiolarians. Latest Devonian to Earliest Carboniferous bedded cherts occur in sequence previously mapped as Amamoor beds and Gympie Group.

Jan 1, 1990

By Willey GJ

A brief test program was undertaken to assess the viability of air-sparged hydrocyclone beneficiation at the Cadjebut concentrator. Three different process streams were processed (lead rougher feed, lead scavenger tail and `mine water' solids) in a small scale ASH unit (one litre volume, feed rate 1000 to 1800 kg solids/hour). Analysis of the concentrates indicated that ASH based flotation was successful, selective and capable of achieving improvements to the overall metallurgical performance of the concentrator. The flow regime inside the device accentuates the selective flotation of the finest particle size ranges generally not recovered to any significant extent in conventional mechanical flotation devices. The testwork proved that the ASH is a viable alternative option for increasing the flotation capacity of the lead beneficiation stage of the Concentrator.

Jan 1, 1993

By Mining Geophysics

Modern geostatistics has eliminated much of the guess-work in ore reserve estimation, and can calculate levels of confidence for the reserve estimate. Geological modelling software has brought about a revolution in the communication of complex geo-variables to mining engineers, metallurgists, surveyors and managers. Mine planning and scheduling can now avail itself of a veritable toolbox of enabling technologies.

Jan 1, 1994

World class ore deposits can be defined commercially as deposits which contain metal concentrations in the upper quartile of resources size and/or grade, world wide, from which economic extraction can be undertaken, over a production period exceeding ten years, at a cost below the weighted average cost of cumulative production of the contained principal commodity of mines world wide.

Jan 1, 1993

A general approach to the analysis of processing technology is presented using the concepts of Process Aims, Process Characteris- tics and Process Costs. From an examination of the processes used in extractive metallurgy a hierarchy of process aims is identified, these aims are separation, compound formation,, metal production and metal purification. The application of this methodology to process flowsheet development is described.

Jan 1, 1984

By M Bezzina

In 1995 Standards Australia International Limited æSAIÆ published a risk management standard titled AS/NZS 4360 Risk Management. It was the first such standard published by a recognised formal standards body anywhere in the world and it put Australia at the leading edge of the risk management discipline. Many Australian and international organisations have utilised the risk management standard and it is one of SAIÆs most important and popular standards. Since its publication in 1995, the risk management standard has gone through a major revision in 1999 and is currently undergoing another such review, which is due for completion in 2004. This paper will chart the application of the standard within certain key organisations since its inception in 1995. A brief overview of the methodology behind AS/NZS 4360 will be presented as well as an overview of supporting and related standards. It is prudent to base risk management and other management system issues on existing and tested standards rather than creating new proprietary approaches. Examples of areas in which the risk management standard might be applied in the mining industry are given, subject to the specific operations of each company: technical, commercial, environmental, informational, and safety and regulatory.

Jan 1, 2003

By Y Hansen, J Petrie

Life Cycle Assessment (LCA) is increasingly being used as a decision-support tool within mining and minerals processing and metals production. However, a number of initiatives have highlighted the current limitations of LCA to accurately reflect the environmental performance of minerals and metals. These programs include:the Mining, Minerals and Sustainable development project (Stewart, 2001); the United Nations Environment Programmme/Society for Environmental Toxicology and Chemistry (UNEP/SETAC) workshop on LCA and metals (NRCan, 2002); the UNEP SETAC Life Cycle Initiative; and the review of the existing ISO 14 040 set of environmental management standards. Together, these initiatives highlighted concerns relating to the ability of LCA to engage with and support metals recycling, to adequately reflect the impacts associated with products from a multi-product orebody, the ability to adequately reflect the toxicity potential of metals in the natural environment and the fact that resource depletion focuses on mining (and not consumption) as the depleting activity in the life cycle of a metal. Additional impact categories to be included in LCA were also suggested. In this paper we demonstrate how existing initiatives are addressing LCA limitations. Finally we present the state of the art in Life Cycle Impact Assessment (LCIA) for two impact categories:resource depletion; and impacted land footprint for solid wastes.

Jan 1, 2004