Search Documents

Average annual growth in consumption of primary energy in Australia over the past 10 years has been 5·5 per cent compared to a world average of 4·1 per cent.Over the next 10 years growth rate is expected to increase to 6 per cent per annum due largely to the rapid development in the mineral processing industry.By the end of the 19705 natural gas is expected to supply more than 9 per cent of Australia's primary energy market. Coal will supply 40 per cent and petroleum products 47 per cent. Nuclear energy will make its appearance but will make only a small contribution in the period.Australia has adequate reserves of natural gas and coal to supply its needs in the 1970s and beyond. However the newly developed reserves of crude oil, while supplying 60-70 per cent of requirements in the initialyears, will need regular and sizable additions if they are to keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated that new discoveries will need to approximate ten times the volume of recoverable reserves found in Australia to date.

Jan 1, 1971

By Yoshii Y

Many kinds of shield machines are being driven in the soft ground of Tokyo metropolitan area. Tunnel alignments for underground power transmission lines are generally planned to pass under public roads where facilities, especially life-line facilities, are densely located. Therefore, it is frequently required to drive the shield machines along very sharply curving routes. This paper reports on the performance of the new shield machine - the Sharp Curve Excavation Shield Machine - developed by Tokyo Electric Power Co., Inc., which can freely drive along a much sharper curve than conventional machines. Some of features of the developed devices of this machine are, maximum flexing angle of 6.5 degree in all deirection at the middle of shield body, maximum bending angle of 3.5 degree in all direction at the cutter disc, and so on. This shield machine can there- fore drive along curve of minimum radius 15m. The machine was confidently applied to the const- ruction of tunnel in soft clay strata at N values 2 to 5. Outer diameter 3.7m. Length 202m. Horizontal curve; radius 15m, length 20m x 2. Vertical curve; radius 30 m, inclined driven up 29%. The behaviors of the shield machine, segments and surrounding ground were monitored during construction for safety and efficiency check of this machine.

Jan 1, 1987

By Borgelt B. V, Perry A. J, Wellington H. K

There has been little change in the lead smelting practice at Mount Isa since 1939 when the metallurgy and general practice were outline by Raney and Blott.The purpose of this paper is to descriqe some of the operational details that have influenced the overall production. The slag fall hns been increased by the lowering of the lead content of the concentrate. Further, as it is the practice to include iron on the furnace charge and carry a higher lime content in the slag, both factors have produced notable results in furnace operations.All blast furnace gases are filtered in a baghouse and this unit is. being further extended to take all smelter gases, thus eliminating the existing Cottrell plant handling Dwight-Lloyd gases.The lead smelter was closed down from April 1943, to May 1946, during which time blister copper was produced.The report is subdivided as follows:-1. Filtering and Mixinga. Effect of calcium sulphate on cloth.b. Dwight-Lloyd charge composition.c. Main mixer.d. Return sintel sizing.2. Blast Furnace Operationsa. Introduction.b. Use of orehearth.

Jan 1, 1953

By K Inoue

The pressure oxidation of molybdenite concentrates in acidic and alkaline media has been studied. The conditions of the selective oxidation of copper and iron sulphide minerals with a quantitative copper leaching by ferrous-ferric-sulphate solution have been found and explained from the point of view of electrochemical kinetics. The partly oxidised residue consisting of molybdenite and (hydro-) oxide of iron (III) was then decomposed by oxygen in alkaline media. Effects of the main parameters, such us oxygen pressure, leaching temperature, solid-liquid phase ratio, autoclave stirring speed as well as lixiviants nature on the molybdenite oxidation rate have been established.

Jan 1, 2000

The passage of a vast array of new State and Federal environmental legislation over the last couple of years has required many mine operators to sharpen their focus on environmental requirements. Established requirements, such as environmental impact assessment, minimising disturbance and rehabilitation must now be complemented by mine environmental management plans. These may not only require regular monitoring of mine operations and detailed forward planning to prevent or reduce environmental harm caused during mine operation, but annual updating. It is likely that in future these plans will be required to incorporate general principles such as pollution prevention, sustainable development, waste minimisation and conservation of biodiversity and ecological integrity.

Jan 1, 1993

By J Brown, C Roberts

The scope of this paper is to recount the development of segmental linings used in tunnel construction, starting with its inception as an improvement to the brick-lined tunnel approach of Brunel in England and moving through the history and development to the present day, before finishing with a few insights into what the future might hold. The paper also discusses the motivation for the relatively recent move towards replacing conventional steel reinforcing cages with steel fibres and the reasons why steel fibre reinforced concrete (SFRC) is rapidly becoming the material of choice for manufacturing precast concrete segmental linings.

Jan 1, 2008

Mount Isa Mines operates Hewlett Packard 1000 computer systems for process control in its major mineral processing plants. To simplify control systems implementation, a process control software package has been developed. This package is now used at the Lead/Zinc Concentrator where the HP computer is interfaced to Foxboro Interspec/Spec 200 system and Honeywell TDC 2000 front-ends. The HP computer controls crushing, grinding, flotation and tailings disposal. This paper outlines the development of process control systems at Mount Isa Mines. The creation of the process control package is described and the reasons for its development highlighted. The application of the software package and the implementation of process control systems at the Lead/Zinc Concentrator is detailed.

Jan 1, 1978

By Shining Z

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The rheological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

As modern techniques of Petroleum Exploration and Development are rela-tively new in Australia,2 the alien terms "Mud Logging" and "Core Analysis" will bear explanation. Mud Logging and Core Analysis are two of the Petroleum. Industryts most useful "tools" in the successful search for, and development of, commercial oil and gas deposits. Modern Mud Logging could be more accu-xately termed "Drill Cuttings and Mud Gas Analysis". Presently, mud-logging has its greatest application in exploratory wells where subsurface geologic control is at a-minimum.

Jan 1, 1962

The Department of Resource Industries regulates and oversees safety and environmental standards for the mining and related industries in Queensland, and provides scientific support through its effort in the geosciences.The geoscientific data base accumulated over more than 120 years is very large. Therefore, accessibility to and utilisation of the data base in the most effective manner is an issue to be addressed in terms of modern information technology. The Department has developed a strategy whose implementation is progressing rapidly.

Jan 1, 1990

Silica-Kaolin Sand Wet Sizing The Bulgarian deposits of silica-kaolin sand are localised in the eastern part of the Danube plain. After wet separation the raw material yields two products - washed kaolin (different grades) and silica sand (different grades). The water washing technology includes: disintegration; spiral classification; hydrocyclone classification and dewatering of kaolin grades; hydroclassification; sizing using drum screens and dewatering of silica sand grades. Research and development program has started to improve the silica-kaolin sand separation in processing plants. Based on the raw material and tails characterisation data and the preliminary experiments using Derrick Stacksizer screening machines a silica-kaolin sand wet sizing technology was developed. The full-scale pilot flowsheet includes the following units: Derrick Stacksizer equipped with 0.43 mm opening Derrick Urethane Panel; 500 mm Flat bottom Hydrocyclone; Derrick Stacksizer equipped with 0.150 mm opening Derrick Urethane Panel; 100 mm Hydrocyclone and Derrick Dual Motor Linear Motion Machine equipped with 0.064 mm opening Derrick Pyramid Panel. The pilot-test data clearly demonstrate that the new silica-kaolin sand wet sizing technology is suitable for Bulgarian silica-kaolin raw material. There are possibilities to increase the silica sand recovery increasing the production of silica sand grade PK 0.16 and starting the production a new grade PK 0.10.

Sep 13, 2010

By G J. Corbett

Magmatic-related low sulfidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.   Low sulphidation systems in the south-west Pacific region exhibit a vertical zonation in deposit types: from porphyry copper-gold at deep levels, quartz-sulfide-gold at mesothermal to deep epithermal levels, carbonate-base metal gold at mainly epithermal levels, and epithermal quartz silver-gold at shallow levels. It is interpreted that the characteristics of each of these styles of deposits is produced by mixing with circulating waters of different physio-chemical compositions.

Jan 1, 1995

The New South Wales Department of Mineral Resources has, since 1974, administered the Derelict Mines Rehabilitation Program (DMRP) to reduce the environmental impacts of abandoned and orphan mine sites. The application of the DMRP is presented in case studies of sites from the South Maitland Coalfield featuring residual drainage of acidic and saline water in a semi urban and rural community setting. The acidity here is typically derived from iron oxidation in shallow underground coal mine workings and in surface emplacements of coal washery reject materials. This paper presents summary information on AMD investigation, monitoring and rehabilitation. The experiences of community expectation, stakeholder consultation and peer review are discussed.

Jan 1, 2003

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops.

Jan 1, 1992

By Royston D

Victoria has an extensive brown coal resource, 202,000 Mt, of which 43,300 Mt is regarded as readily recoverable. This brown coal is located principally in the Latrobe Valley as thick seams and is being extracted at low cost primarily to support base-load electrical power generation. The high moisture content of the coal is partially off-set in many applications by the high reactivity of the coal and the generally low levels of potential pollutants such as ash, sulphur and nitrogen in the coal. Large scale development of this brown coal resource began in the 1920's. In addition to electricity generation, it is used for briquette production, carbonisation of briquettes to char and was gasified for town gas supply to Melbourne (1956 - 1969). The BCLV coal to oil pilot plant at Morwell is a major new initiative in the use of Victorian brown coal. Many other new developments are in place and emerging in the utilization of low rank coals. Examples of these developments are, the large-scale gasification of lignites in the USA, and value-added products such as bulk chars, solid fuels, activated carbons and coal-water mixtures. The Government of Victoria has created the Coal Corporation of Victoria to promote current sales of briquettes and to encourage further new industrial developments based on the State's brown coal resources, in particular the Loy Yang coalfield. The Coal Corporation also has a vigorous product and process oriented research and development Programme.

Jan 1, 1987

Highwall mining commenced in the Appalachian region 50 years ago. With innovative equipment design introduced in more recent times, penetration distances over 300 m are now commonplace. It is only in the last three years that highwall mining has become part of the Australian coal industry. Geotechnical evaluation is an integral part of the Australian procedures, and although still being refined, has already proven its worth. Statutory guidelines have also been prepared for operations in Queensland. This paper explores trends in equipment design, geotechnical prediction, operating techniques and statutory requirements with regard to highwall mining Australia's coal deposits. A quick assessment guide to assist in the evaluation of potential sites is included.

Jan 1, 1992

By Rozycki J

The results of shaft lining monitoring gave rise to an investigation of cracks observed in the structure. An hypothesis was made that the cracks might be due to stresses caused by energy wave propagation, triggered during blasting or by the rock falls. However, it could not be excluded that the cracks had their origin in the rheologic changes taking place in the concrete. To prove the hypothesis, an investigation of the scale of the increase of stress due to the energy triggered was undertaken. At the same time it was decided to attempt to determine the "damage threshold" for such material in the danger zone. In the paper the investigation and its results are presented, as conducted in one of the shafts. In conclusion, certain generaliza- tions are proposed to give a starting point in the consideration of similar problems elsewhere.

Jan 1, 1987

By Loo R

The Paper discusses the size and extent of in-pit dust suppression problems created by iron ore mining in the Pilbara region of Western Australia. Dust problems associated with drilling, loading, hauling and tipping are discussed indicating the large quantities of water which can be applied for dust control and attempts that have been made to rationalise this water usage to obtain maximum benefits from the applied water. The magnitude of the problem and the quantities of water involved can be appreciated when one realises that 275 000 tonnes of rock are moved on Mt. Whaleback each day and that there are 40 km of haulroad within the open pit. Initially dust suppression was limited to the spraying of haulroads by large water tankers. Now dust suppression is practiced during drilling and after blasting, wind blown dust is reduced by application, using water cannons,of large quantities of water to floor stocks prior to loading operations as well as by the installation of 16 km of automatically controlled fixed sprinkler reticulation on the main semi-permanent haulroads. The methods used to assess the water requirements for in-pit dust suppression are discussed and the extensive development testing used to evolve the present installations are 1. Environmental Superintendent Mt. Newman Mining Co. Pty. Ltd. Newman, W.A. 2. Chartered Consulting Engineer, Perth, W.A.

Jan 1, 1979

By McNabb K. E

Significant coal reserves in New South Wales lie under areas with steep topography such as valley slopes and cliffs. Subsidence predictions are difficult to make for these locations as existing empirical databases cannot cover all permutations of topography and mining geometry. Two dimensional numerical model alternatives are of limited applicability. Consequently a novel three-dimensional numerical model is developed including the detailed panel layout, realistic rock mass properties including the full stratigraphy, goaf behaviour and actual surface topography. Model results show the same trends as subsidence measurements from Baal Bone Colliery in the Western Coalfield of New South Wales.

Jan 1, 1992

The first 12 m diameter rakeless thickener in the Australian gold mining industry was installed to treat plant tailings at the St Ives gold plant in April 2000. The plant processes approximately 3.2 M tonnes of ore producing about 430 000 oz of gold per annum using conventional crushing, grinding, gravity and carbon in pulp processing methods.The main benefit sought from the thickener was to improve water recovery in the plant and provide water for a 55 000 oz per annum heap leach operation. The thickener design indicated that more than 128 m3/h of overflow water could be returned directly into the plantÆs water circuit, relieving the demand on the borefields. The resultant surplus in the water circuit would then be available for the heap leach project. Based on laboratory and pilot plant scale tests conducted by EIMCO the thickener was designed to handle up to 700 m3/h of tailings slurry (450 tph of solids) with a 40 per cent oxide component in the ore blend. The normal plant throughput is 565 m3/h of slurry (400 tph of solids). Gold mineralisation in most areas at St Ives comprises quartz-sulphide vein and breccia lodes with common albite-biotite-chlorite alteration assemblages. There are well developed supergene gold horizons in the clay-oxide profile above most of the deposits (Osborne, 2002). This results in a wide variety of ore types being treated. At times 40 - 50 per cent of the ore may be oxide in nature. After some commissioning difficulties associated with instrumentation, the thickener has performed satisfactorily although it has not reached its design capacity. The maximum density achieved under normal operating conditions with 20 per cent oxide ore is about two per cent below the design. The thickenerÆs performance deteriorates further with increasing amounts of oxide ore in the blend. The thickener has provided sufficient water for the successful operation of the heap leach and has also provided some down stream benefits for the gold plant by way of pH and cyanide conditioned thickener overflow water.

Jan 1, 2002