Search Documents

By K L. Silversides, A Chlingaryan, A Melkumyan

Multiple data sources can be fused to improve boundary modelling in stratified deposits such as the banded iron formation (BIF) hosted deposits in the Pilbara Region of Western Australia. Accurate boundaries are essential to produce high quality geological models. Initial models are based on the widely spaced exploration hole data. This creates a high level of uncertainty in areas between the holes, with different interpretations of the boundary equally probable. Including directional information collected in these holes in the models can reduce the number of possibilities. Including data collected during mining, such as blastholes and bench measurements, can further guide the model. This research demonstrates a Gaussian Processes based method of fusing these disparate data sources to better inform the boundaries. Our results demonstrate that when only exploration points are used the model creates a smooth boundary with minimal variation between the holes. Each additional data source refined the model and added additional detail to the boundary. For the blast data, the new detail projects down to the bench below the current bench to allow for a better prediction before mining commences on that bench.

Mar 22, 2022

Sampling and analysis of mineral deposits need to be executed without fear or favour of financial or personal impacts. Examples are given to illustrate the effects of departures, witting and unwitting, from correct use of appropriate techniques and/or equipment with emphasis on exploration and mining of porphyry copper deposits of the Pacific Rim. Some of the results of errors on the low and high sides of true value in exploration, resource or reserve estimations and in production caused by sampling and/or sample preparation mistakes, faulty practices, equipment and/or analysis are considered.

Jan 1, 2004

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health rleterinratinn_

Jan 1, 1988

During 1995 a catastrophic accident took place at the No 2 Vaal Reefs shaft in South Africa, when a locomotive fell onto a cage, causing the death of 104 people. The subsequent Commission of Enquiry found that the safety detaching hook had opened when hit by parts of the falling locomotive, detaching the cage from the rope and allowing the cage to drop 400 m down the shaft. It was believed that had the hook not detached, the rope would have been sufficiently elastic not to have failed, implying that many fatalities may have been avoided. In addition, the risk of accidental opening of hooks due to impact with smaller falling objects in shafts became a concern. This paper deals with a comprehensive statistical investigation that was performed to quantify this risk, establish acceptable levels of such risks and to derive criteria for the resistance of detachment hooks against accidental opening caused by impacts. The investigation involved a survey, dynamic finite element analyses and Monte Carlo simulations.

Jan 1, 2005

Vatukoula is credited with the second largest population in the Colony of Fiji. Within an area comprising 550 acres are living approximately 4,500 people. Of these, about 1,150 Fijians, 90 Rotumans, 90 Europeans, 180 Part-Europeans, 180 Indians and 30 Chinese and miscellaneous Pacific islanders are employees of the Associated Mining Companies.The remainder is made up of employees dependants with a small minority of tradespeople and Government servants, such as storekeepers, school teachers, police and post office officials.To appreciate fully the work involved in the administration of this unusual community it is necessary firstly to know something about the various types of people which compose it.The FijiansAlthough the Fijians are of Melanesian stock their physical characteristics indicate a Polynesian strain. Natives from all provinces in the Colony are to be found in Vatukoula and their varied types point to this MelanesianPolynesian intermixture. For example, there are people from Lau** and Kadavu who are tall and well built with good features and comparatively fair skins contrasting with the dark, broad featured and generally short people of the hill tribes of Ra and the coastal tribes of Bua.The Fijians, particularly the older people, are noted for their dignity, courtesy and hospitality. The young Fijians of the present generation, large numbers of whom are...

Jan 1, 1953

This paper presents the water management plan of the Mae Moh Project in the North of Thailand, which includes a large lignite opencast mine and thermal power plants. Lignite production will increase from the present 5.5 million tons per annum to approximately 20 million tons per annum by 1995 when the pit area will be about 20 sq.km. and the depth at over 300 meters. Seven power plants are proposed of which two are under construction. The total capacity to be installed is 2,925 MW. The principles considered for water management are firstly flood protection, including drainage of the mining pit and diversion of the Mae Moh stream away from proposed future mining areas; and secondly, a plan to meet the water requirement of the thermal power plants, while maintaining downstream supplies for irrigation and other purposes. The limited annual run-off of Mae Moh and Mae Chang watershed basins are inadequate for the proposed power plants. A study has been prepared to compare two approaches, namely conveying water from remote watersheds to meet the water requirement of the power plants up to total installed capacity; or by limiting future total generation, at the existing site, to only 2025 MV.

Jan 1, 1988

By J Andrina, D Richards

The Grasberg is a large copper and gold open pit mine operated by PT Freeport Indonesia and located in the high equatorial mountains of Papua Province, Indonesia. The climate is alpine/sub-alpine with little seasonal variation in temperature and rainfall. The annual precipitation varies from about 3000 to 5000 mm over short distances around the Grasberg, but in general, an average daily precipitation of 10 mm per day applies and leaching of the overburden is continuous throughout the year. Mining commenced in 1988, and almost all of the overburden mined up to 2003 was potentially acid forming. The current acid drainage from this overburden is being collected and treated. From 2004 to the end of the Grasberg pit operation in 2014, approximately 70 per cent of the overburden will be potentially acid forming and 30 per cent limestone. A program of laboratory leach columns, field test pads and an instrumented full-scale dump was developed with the objective of defining scale up factors to quantify the acid and metal leaching rates and to evaluate the stockpile geochemistry and control options. The results of an ongoing seven year program have demonstrated feasible scale up between laboratory columns, field test pads and the trial dump in relation to material geochemistry and ARD evolution trends at Grasberg. The potentially acid forming waste types are highly reactive and maximum acid generation rate occurs within two to three years and that maximum copper release occurs within one to two years of exposure. The results also show that the net acid generation (NAG) test provides a good estimate for the potential acid load from overburden types. The chemistry, temperature and oxygen data from the trial dump suggest that oxidation and acid generation is occurring throughout the dump but at a decreasing mass rate with increasing distance from the toe of the dump. It is apparent that convection and/or advection are important mechanisms for the transport of oxygen into and within the dump. Key results and findings of the investigations carried out are presented and the implications of the findings for long-term ARD management at the Grasberg mine are outlined.

Jan 1, 2003

By Smit J. G

Following an increase in the number of methane ignitions in South African coal mines a new ventilation system was developed. The "Hydravert" system conceived in late 1979 for use in low seam coal mines, where the bord and pillar method of working is used, has been extensively developed to include applications for mining seams up to 4.5 metres high. A brief history of the development is supplied including some of the pitfalls encountered in the hydraulic equipment design and selection.

Jan 1, 1988

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

Utah's Blackwater mine began operations in 1967. The four CQCA mines controlled by Utah followed over the period 1971 to 1979. Project feasibility studies for all these were based on open cut mining to overburden depths of 60 metres, with typical project lives of 12 to 16 years, depending on reserves Further studies, initiated after the mines had started, showed that continuation of open cut mining beyond the 60 metre highwall was viable. In 1973, the Deep Stripping Project (DSP) was launched to define the scope for stripping deeper, to determine what the additional equipment needs might be, and to pu forward proposals for a full scale trial system. The project commenced at grass roots with a literature survey, proceeded through a sequence of equipment evaluation, specification, design and manufacture to the commissioning of the Goonyella BWE system. Studies are continuing to assess the future deep stripping requirements for all Utah's Bowen Basin mines.

Jan 1, 1983

By Marshall T, Nicholson DS

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while ooencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By King MN, Travis IC

PISCES - the Planning and Information System for Coal Export Services has been developed by Port Waratah Coal Services (PWCS) to ensure the efficient and economic operation of the Hunter Valley Coal Chain. PISCES is a computer based integrated information and management system to coordinate operations commencing at minesites through the coal chain to shiploading at the Port. The PISCES system comprises a central database around which a number of planning modules interact. These include interactive programs for train planning and timetabling, stockpile management, berthing analysis and a coal shippers enquiry system. PWCS has previously developed - number of computer based systems for planning, controlling and monitoring complex coal handling operations and the extension of the PISCES system to the Hunter Valley Coal Chain is another initiative to assist the Hunter Valley Coal Export Industry in looking confidently towards the Future.

Jan 1, 1987

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

The emergence of a new range of database communication standards and software has provided the impetus for the development of a new approach to exploration and mining data management. The acQuire software produced by acQuire Software Pty

Jan 1, 1998

By G Chitombo, M Ruest

In surface mining, studies of the kinematics of blasted rocks using high speed film/video image analysis have allowed the estimation of the starting time, direction and magnitude of visible movement of fixed sections of the free face. Horizontal displacement versus time plots from discrete targets at the face generally report changes in slope over very small time intervals. These changes indicate step increases in velocity due to the action of explosive gases. In practice, the onset of rock mass movement, different to localised spalling, has been associated with a response time which exceeds the combined times of detonation, propagation and reflection of stress waves. This time is referred to as minimum response or burden movement time. As an engineering index, burden movement time has been used to provide guidelines for the selection of inter-hole and inter-row delay sequences in production blasting. With respect to improving breakage and fragmentation, it has been demonstrated that the delay interval between adjacent explosive charges should be less than the expected burden movement time. Similarly to reduce confinement between rows, delay intervals should exceed the expected burden movement time. The Hybrid Stress Blasting Model (HSBM) is a modelling framework that dynamically links an ideal and non-ideal explosives detonation code to a geomechanical rock model. This blast simulation tool is aimed at analysing the role played by different explosive formulations in fragmenting and/or damaging various rock types under different degrees of confinement. In the current framework, the rock behaviour under extremely high pressures and loading rates is calibrated from shock tests and the role of the explosive in fracture growth is accounted for and assumes a compressible fluid flowing through the explicit fracture network. The model is being developed as part of an international collaborative research project funded by a consortium of companies comprised of explosive and equipment suppliers and major mining houses. As part of the development and validation of the HSBM project, data from literature addressing the kinematics of the rock mass (ie burden displacement, face velocities and response times) has been collated and used to evaluate the current version of the code. A series of numerical experiments have been conducted with the view to: evaluate the response of the rock mass to changes in burden distance given by the impact of both stress waves and radial gas flow pressure;compare the modelling outcomes in terms of displacement, response time and face velocities to documented field observations; andcompare stress induced and stress/gas induced modes in terms of burden displacement outcomes. Results from these experiments have shown that in its current form the model is able to capture the trends observed and measured in practice. This is with respect to the simulation of burden displacement, response time and average face velocities for different geometries and charging conditions. The experiments have served as consistency checks which form part of an ongoing and comprehensive evaluation and validation of the HSBM code also aimed at addressing some of its current limitations.

Jan 1, 2007

By Vassiliev P

Cut-off optimisation, based on the work of Lane (1988), can be used to maximise the NPV (Net Present Value) of a mine by the judicious manipulation of cut-offs and the use of stockpiles. Apart from maximising NPV, cut-off optimisation will ver

Jan 1, 1998

By Rynn J. M W, Paynter A

Recent studies by the authors have concerned themselves with assessing the earthquake risk to north-eastern Australia, based on available historical earthquake data for the area. There have been several significant earthquakes (Richter local magnitudes of the order of 6) concentrated in the Wide Bay - Burnett region in central eastern Queensland, although none of these has occurred close to a significant centre of population or development. Using derived average acceleration attenuation relations and world-wide data on earthquake-induced damage as a basis, conditions under which earthquake-induced liquefaction may occur have been investigated and presented in graphical form. Historical earthquake data for north-eastern Australia have been overlain on this graphical presentation and it has been demonstrated that the Wide Bay - Burnett region, in particular, may in the past have been on the verge of earthquake-induced liquefaction, where ground conditions are susceptible. When this is viewed in the context of the rapid growth in population and development in this area over recent years, the risk can no longer be ignored with impunity.

Jan 1, 1990

By Hefter G. T, Singh P

The use of sulphur dioxide (SO2) as an anode depolarizer in place of traditional oxygen evolution reduces the energy costs of copper electrowinning. This paper reports the effect of various metal ion impurities, which are usually present in th

Jan 1, 1998

By Quast K. B

Laboratory batch rod and ball milling tests were conducted on samples of Heavy Medium Separator (HMS) sinks from Renison Tin Limited. The product size distributions for this heterogeneous material were very different to similarly sized homogenous material previously reported by the authors. The effects of pulp density on product size distributions were only evident at pulp densities greater than 80 per cent solids. At high solids density, the major weight distribution product peak fell and broadened indicating less efficient breakage, particularly for rod milling. Tin distribution in the ground products was also affected by pUlp density, and there was always less cumulative per cent tin than cumulative per cent weight, ie there was no tendency for cassiterite to slime down to 10/lm.

Jan 1, 1995