Search Documents

By Williams SR

Column Flotation cannot be used indiscriminately. Based on extensive pilot plant experience at Lakefield Research, a number of limiting parameters have been identified for the application of column cell flotation. Parameters of importance are the use of wash water, flotable mineral content, pulp viscosity, type of mineral selectivity being sodght and degree of mineral liberation. The paper discusses when wash water should be used and the positioning of a column within the circuit as this is important to maintain a sound water balance for the circuit and prevent excessive circulating loads. Other areas of debate are pulp chemistry, very low and high weight recovery, for which the conventional column is a poor selection of equipment, and treatment of complex ores, where the separation of valuable minerals is more difficult than non-sulphide, sulphide mineral separation. Based on these observations, the application of column flotation must be carefully considered or can be optimised.

Jan 1, 1993

By Sullivan T. D, Lohe E. M

Geological structure is one of the main controls on ground conditions within mining. It has a significant impact on the mining conditions and productivity of coal mines within the Sydney - Bowen Basin. The three main types of faults common to this region, normal, reverse and strike-slip systems, each present distinct challenges to mining. These systems effect a wide range of geotechnical and mining conditions within the mines. These include coal quality, strata stability, goat and caving behaviour, productivity and maintenance schedules of mining equipment, mine design and mine-site stress fields. A better understanding of the regional, local and mine-scale structural setting, timing relationships of structural events and the mechanisms of fault formation will greatly aid industry's push for greater productivity and competitiveness.

Jan 1, 1991

From 1980 to February 1991 the Rosebery concentrator purchased ore from Aberfoyle's Que River Mine. Following the termination of the contract the concentrator reverted to treating Rosebery ore alone. Since that time it has become apparent that the circuit configuration employed was no longer optimum for zinc metallurgy. The circuit was designed to treat a difficult, slow floating sphalerite; however, the opposite was now found to be true. The sphalerite is fast floating and the circuit was cumbersome. During 1992 extensive circuit changes led to the provision of a simple open circuit flow sheet. The circuit is now easier for operators to understand and lends itself to improvements in process control. Middlings streams have been minimised, which produces a far more stable circuit. Significantly, it must be noted that the key to achieving potential results must lie in reducing variations within the process. A significant ore characterisation program has been undertaken, providing an insight into the metallurgical compatability of the ore to be mined. Using the information collected in this program, metallurgical recoveries and grades can now be predicted with a geater accuracy. Ore characterisation data suggests that an improvement from a 54 per cent zinc concentrate to a 57 per cent zinc concentrate should be achievable. By understanding the size-by-size mineral assemblage, a strategy for concentrate grade improvement has been developed. The requirements of the customer must in all cases determine the quality of the product. Pasminco is a fully-integrated zinc producer and as such significant gains can result by tailoring the concentrates to suit the Smelters.

Jan 1, 1993

By Hunter T. C

The wirebar furnacing and casting facility commissioned in 1970 at Copper Refineries Pty. Ltd. (CRL), Townsville, comprising a 70 tonne/ hour ASARCO shaft furnace and a Walker type casting wheel, contained several unique design features. Since commissioning, effort has been directed at improving metallurgical control of the casting process. This has resulted in the identification of optimum mould lubricant properties and the use of continuous on-line measurement of molten metal oxygen content. Casting defects such as cracks and surface porosity are readily explained and controlled using these techniques.

Jan 1, 1977

By Fourney W. L, Weaver T. A

A large number of single borehole crater-forming shots were analyzed in terms of correlating the crater parameters with explosive weight. The objective was to determine a scaling rule for which the explosive weights varies over many orders of magnitude and covers many different geologic materials. Included in the data base are type and weight of the explosive, geologic medium and degree of saturation, charge depth-of-burial, crater dimensions, and crater rim (lip) measurements. An alternative scheme to the usual plot of scaled depth-of-burial versus scaled volume removed was desired. The proposed technique uses a plot of the logarithm of the explosive weight, Y, versus the logarithm of the slant length, R', calculated from the known depth-of-burial of the explosive and the measured crater radius. A plot of Log Y in kilotons versus Log R' in meters from all the crater tests in this data base resulted in a straight line with a of slope 0.31 and showed good correlation between the variables Log Y and Log R'. Since the crater data includes many geologic materials, different explosives (including nuclear tests), and large differences in charge weight, the straight line fit suggests that the type and strength of the geologic materials play a subordinate role to explosive energy in crater formation.\

Jan 1, 1990

A major factor in the economic development of New South Wales has been the ready availability of coal for the major industrial and urban centres of Sydney, Newcastle and Wollongong. Historically, the presence of high quality coal near these areas has acted as a catalyst to urban and industrial growth. This easy access to low cost coal resources over the past 200 years has given rise to a commonly held belief that New South Wales contains vast coal resources sufficient to meet any foreseeable demand. However, a recent study undertaken by the Coal Resources Development Committee has found that New South Wales is likely to face a serious shortage of economically mineable coal in the future. Forecasts predict that demand for New South Wales coal will increase by about 40 per cent, and then remain at about that level for at least a further ten years. To meet such demands, the coal industry will require access to economic high quality coal resources.

Jan 1, 1995

By Caivin JS, Freeman CJ

The Fairbanks Mining District in central Alaska was discovered in 1902 and since then approximately 7.5 million troy oz of placer gold, 250,000 troy oz of lode gold, and several thousand short tons of antimony and tungsten hap been produced from an area of about 1000 km . Historic lode production was from high grade gold-quartz veins that averaged 1.3 OPT free milling gold. Five main types of mineral deposits' are recognized in the district. I. Conformable, stratabound volcanogenic zinc, antimony, lead, and copper sulfides in places containing gold, silver and tungsten in bimodal metavoleanics (Cleary Sequence). II. Complex precious metal-bearing lead sulfosalt-quartz veins in Cretaceous granitic intrusives. III. Tungsten skarns adjacent to granitic intrusives. IV. Gold-bearing polymetallic sulfide-quartz veins crosscutting metavolcanics and metasedimentary units of the Cleary Sequence. V. Antimony-bearing gash veins along axial plane shears in various lithologies of the Cleary Sequence. Type I and Type IV mineral occurrences are currently being evaluated as low. grade bulk tonnage (target model 16-20 'million tons of 0.05 to 0.15 OPT)'and high grade moderate tonnage (target model 0.5 to 2.5 million tons of 0.5 OPT) gold deposits. The host rocks for Type I mineralization occur over a 30 km strike length and are at least 300 meters thick. Stratigraphic, structural, fluid inclusion, and isotopic data suggest that the Type IV mineralization is related to remobilization of Type I

Jan 1, 1987

This paper discusses design concepts in planning a large modern bulk terminal. The need is emphasised for a studied master plan, in-built materials handling flexibility and staged development. An integrated approach is advocated, combining functional purpose designed foundations and structures to serve their mechanical, electrical and environmental functions. Dry bulk and slurry handling are also compared in perspective.

Jan 1, 1983

By Langberg D, Gray N. B

The flocculation of hydrophobic magnetite with gold was examined as a possible means of recovering fine (95 per cent were possible for 1.5 - 3.0 ¦m and 5.5 - 7.5 pm gold sizes. The effect of process variables on the flocculation process was explained by variations in the adhesive force between the gold and magnetite.

Jan 1, 1991

By Thomas R. J

Following asmallnumberofpollutionincidents involving the death of cattle from ingestion of cyanide that had escaped from gold processing plants, the Queensland Government undertook to develop competent guidelines addressing this problem. These guidelines, "Queensland Government Guidelines on Prevention of Water Pollution from Cyanide Use in Gold Ore Processing", issued by the Department of Environment and Heritage, Department of Resource Industries and Water Resources Commission, cover hydrology and general house-keeping intended to reduce the likelihood of significant impact from a spill or unintentional dis- charge of contaminated material. There are three major advances for Queensland embodied in this Guideline: ò the use of a design approach that gives site specific standards rather than trying to give a multitude of standards broad enough to cover all situations, ò the use of hazard assessment and a "critical period" hydrologi- cal design technique, and ò new monitoring and reporting requirements. The guideline is presented here in a summary form:

Jan 1, 1991

By R G Warren

Sparse geochronological data have been combined with data on felsic suites and depositional facies of rocks to provide an overview of the development of the Arunta Block. The study provides a basis for construction of a map showing the distribution of granites and associated felsic extrusive rocks in the Anmta Block. The tectonic evolution can be subdivided into a series of significant time intervals. Only in the initial stage, to about 1880 Ma, was there any subduction-related magmatism. All later felsic magmas were crustal-derived melts. The early, pre-1880 Ma arc-related units in the SE contain small showings of Cu, probably including the small Cu deposit in the Casey Bore Inlier at the edge of the Simpson Desert. The most significant time-interval for formation of mineral deposits was 1820-1760 Ma, when volcanogenic Cu-Pb-Zn deposits formed in the Strangways Metamorphic Complex and also in the Jervois district. Stratabound tungsten lodes in the hanging wall of

Jan 1, 1994

By Ooms M, Scott OJ

This paper is concerned with the design and operation of storage and discharge facilit- ies for bulk solids handling. It presents an overview of the basic design philisophy emphas- ising the influence of bulk solid flow propert- ies and bin geometry on the flow patterns developed and how these, in turn, affect the reclaim efficiency and the bin structural in- tegrity and wear characteristics of both bins and chutes. The salient aspects of feeder design and operation will be discussed and the need to consider feeders as integral parts of the bin discharge system will be stressed.

Jan 1, 1978

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

I In an optical microscope, mild attack by cyanide solutions on various minerals can be observed by means of colour changes as well as etching patterns. However, the mineral may not be identifiable due to the coloured film. In some cases, a transfer algorithm between mechanical stages enables the surface-altered mineral to be identified in the SEM. A more severe attack may not be so informative, as it is not known whether the mineral attacked has been completely dissolved away. The leaching behaviour of some common minerals is described.

Jan 1, 1991

By B Walker, A Robertson, C Wels, S Fortin

A background characterisation study was carried out in the Sangre de Cristo mountains, New Mexico, to: quantify naturally occurring contaminant loads from mineralised areas; define site-specific background concentrations; and to determine key factors controlling spatial and temporal variations in contaminant concentrations. The study included a comprehensive sampling and testing program (paste pH/EC, ABA, leach extraction tests) of soil/bedrock from mineralised areas (including erosional scars), and a ground water and surface water quality monitoring program in selected mineralised watersheds. Results demonstrate that high concentrations of contaminants occur naturally in ground and surface water draining the mineralised area of the Red River basin. The erosional scars were found to represent the major source of acid rock drainage (ARD) (~66 per cent) in this area due to: high rates of weathering and erosion, which continually exposes sulfide-bearing outcrops; and high rates of run-off as a result of high elevation and lack of vegetation. The scar material is generally very acidic (paste pH ranges from 8.5 to 1.5; average = 3.6) with highly elevated concentrations of sulfate and leachable metals. The composition and concentration of leachable metals vary significantly, not only between scars but also within a given scar. While all streams draining the various scar watersheds are highly acidic, each has a characteristic æfingerprintÆ of sulfate and metal concentrations. Most of the run-off from the scars infiltrates into alluvial debris flow aprons and reaches the Red River via groundwater flow.

Jan 1, 2003

By Sneddon A

Expansion of central production facilities at the Kutubu Petroleum Development Project in Papua New Guinea (PNG) required excavation of a steep hillside overlooking operating crude oil processing, storage and pumping facilities. Drilling and blasting were used to remove a large volume of rock which varied from hard limestone to soft sandstone, with zones of soft clay and many underground caverns. Similar ground conditions had made it very difficult to predict and control blast-ing results during previous excavation in this area.Special conditions of the project included restrictions on ground vibration levels at a high pressure oil pipeline and pump station within 100m of the blasting area, and a prohibition on any flyrock. As work progressed, some blasting was necessary with 20m of installations being constructed on the levelled project site. Thus blast design, drilling and charging were carefully controlled to avoid any incidents which could interfere with oil production or progress of the construction project.

Jan 1, 1994

Prior to 1975, most geochemical drainage surveys for gold were based on analyses for pathfinder elements, such as As and Cu, rather than direct analysis for gold, for two reasons. Firstly, analytical methods lacked the required sensitivity and precision to determine gold abundance at background levels in stream sediments (usually in the range 1 - 10 ppb). Direct analysis was also inhibited by concern about the potential for gross sampling error, brought about by the dispersion of gold as rare discrete particles of the extremely dense native metal. This sampling error, commonly termed the 'nugget effect' has two components: erratic distribution of the element within the stream environment, related to hydraulic factors, and the difficulty in taking representative samples, both in the field and later in sub-sampling for analysis. In more recent years the collection of very large samples was commonly advocated to overcome the sampling problem (Hams, 1982; Nichol, 1986).Two methods have been widely used to evaluate the gold content of bulk samples (Elliott and Towsey, 1989). The preparation and analysis of heavy mineral concentrates has in recent years been largely superseded by the leaching of gold contained in bulk samples by cyanide, commonly termed the BLEG (Bulk Leach Extractable Gold) or BCL (Bulk Cyanide Leach) methods. The terms BLEG and BCL are essentially interchangeable and the latter will be adopted for the remainder of this paper. The strengths and weaknesses of these two techniques were compared with conventional total gold analysis on fine fraction (

Jan 1, 1976

By Cortes JP

In a dynamic environment such as the Star Mountains of Papua New Guinea Geotechnical Engineering for the Ok Tedi Project must be described as both interesting and challenging. To be effective a reasonable sized team of dedicated people is required with occasional supplementation by specialist consultants and an annual review process. Ok Tedi Mining Limited's (OTML) Geotechnical Section has a vision to be recognised as the leading mine-based geotechnical engineering section in PNG and to be world class by any international standards. This paper deals with the organisational and operational duties of the Geotechnical Section at the Ok Tedi Mine. One of our major roles is in the area of safety, and in particular in the early warning of natural and mining induced geological hazards that may affect safety and/or productivity. The major activities in- clude geotechnical inspections (pit, waste dumps, tunnels, re- gional), data collection activities and database management, geotechnical design and control work.

Jan 1, 1997

By Prohaska G, Jackson F, Jack B

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By Cox I

Raiseboring is a technique that has become popular in modem mining engineering since the early 1960s. A study has been undertaken at the University of Queensland to determine important factors affecting the optimum diameter of raisebored shafts, excluding local parameters such as the maximwn excavation size that a particular rock type can safely accommodate.This model is used to examine each of these factors and the results indicate that the optimum diameter for raisebored shafts is generally between four and six metres.

Jan 1, 1991