Search Documents

By Billington WG

A structural study of northwest Fergusson Island, part of the D'Entrecasteaux Group, was undertaken using colour and monochrome aerial photography and Landsat imagery. The resulting interpretation shows an upstanding, in part, dome-like metamorphic core complex, which is bound on three sides by an en echelon series of low-angle, thrust faults. Faceted gneissic layers occur throughout the complex. These facets are triangular in plan view and range in size from a few tens of metres, to massive composite zones which traverse the entire uplifted zone, The lower surface of each of the facets are, in fact, low-angle decollements which, during uplift, slid one upon the other to accommodate the vertical and extensional movements. As a consequence, deep structural valleys developed which widen towards the zone of maximum uplift. In many places, recognisable topographic features are replicated on both sides of these valleys, and under the stereoscope can be visually reconstructed to their original pre break-up positions. The southern margin of the core complex is less dome-like and falls away, via a series of deeply-entrenched structural valleys, towards a volcano-studded lowland. The lowland appears to belong to a rift or arm, stemming from the more southerly located Goodenough Bay Infrabasin.

Jan 1, 1987

The mineral pulp as it passes through grinding-classification, flotation and solid-liquid separation is examined in the context of it being a particulate fluid. By focussing on the complex viscosity and yield stress of the fluid, new control strategies are discussed. The mineral-particulate fluid is dominatred by non-Newtonian rheology (ie shear thinning, shear thickening, shear yield stress and compressive yield strength). The control of this Theology is seen to be dependent on the fundamental practice-particle interaction forces and with adequate information, it is possible to use the complex shear properties to advantage. The advantages, in terms of final waste and concentrate management, to high weight per cent solids in the mineral particulate fluid, are explored and control strategies outlined.

Jan 1, 1993

In comparisons of a trial extruded brick containing 33 per cent coalwash and 67 per cent clay and a trial pressed brick containing 100 per cent coalwash with a standard extruded clay face brick, the mixed feed stock trial brick compared favourably with the standard brick. If a highly plastic clay is used to mix with the coalwash, satisfactory results are obtained in respect to dimension, strength, water absorption, efflorescence, resistance to salt attack, hardness, colour, weathering, mineralogy and porosity. Although a brick containing only coalwash can be successfully manufactured in a press, its mechanical and physical properties are inferior. This mixed feed stock brickmaking technology leads to the utilisation of a by-product with a potential saving of raw material costs. The extent of use is likely to depend on the proximity of the coal washery and the brickworks and the economicsof transportation costs.

Jan 1, 1992

By Glenn R. J

Treatment processes are outlined for the recovery of rutile and zircon from the heavy mineral-bearing sands on the east coast of Australia. With the exhaustion of the higher grade deposits and the imposition of more rigid specifications for the finished products, strict metallurgical control has become necessary.A description is given of the methods used by The Titanium Alloy Manufacturing Co. Pty. Limited to control the operation of suction dredging, of wet concentration using fans and spirals, and of dry separation using high tension and electromagnetic processes. By applying these methods a plant designed for an output of 15,000 tons of rutile per year has been tuned to produce over 20,000 tons of rutile and a corresponding amount of zircon.Details are given of (a) the method of drilling to determine the extent and grade of the ore bodies, (b) a simple electrically-timed pneumatic automatic sampler, and (c) the methods developed for the physical estimation of quartz, rutile, zircon, ilmenite and "others" in the products of plant operation.The method used for calculating the metallurgical balance and the forms used for the reporting of production results are presented.Examples are given which show the value of this detailed production and metallurgical control of plant operation.INTRODUCTIONThe organization which is now known as "The Titanium Alloy Manufacturing Co. Pty. Limited" (T.A.M.Co.)-a subsidiary of National Lead Company-commenced operating at Yamba, N.S.W., in 1935. A mixed natural concentrate was at first simply dried and bagged and later was upgraded by the removal of silica and the lighter heavy minerals on shaking tables and, after air-drying, was bagged for export. At that time zircon was the most wanted constituent.

Jan 1, 1960

Ventilation characteristics of a three h -nc longwall development panel in a 1/100th tale hydraulic model using dispersion mechanics are the first applications of its Find in ventilation. Dispersion mechanics gives additional and important ventilation parameters such as degree of mixing, bypassing, -ecirculation etc. These are not obtainable the traditional pressure-volume methods. Experimentally, the model work investigates entilation characteristics of different stopping layouts, including leaky stopping,, cut-throughs and return roadway, brattice tyre ventilation and the effects of flow rate reduction on air distribution in the headings. Additionally, a model of methane generation at the face provides results used to calculate the dispersion characteristics in the return airways. It is concluded that the model resui,s -trongly suggest that dispersion mechanics could be applied to mine ventilation surveys to provide quantitative flow pattern data and details of effective dispersion '?_C!,r riro ò `b' eritilat.ing air.

Jan 1, 1983

By Clarke DS, Sporli KB

Structure is an important control in the localisation of gold mineralisation in epithermal systems. There has been, however, only limited investigation of the structural elements involved; such a study is currently directed at the gold deposits of the Coromandel Volcanic Zone (CVZ). Here, mineralised veining and brecciation ranges up to tens of metres in thickness. Dips of veins are mostly steep, but not vertical, and there is a significant number of low angle veins.The structural control of epithermal deposits may be considered on four scales. At the mega-tectonic scale, pre-volcanism fault patterns mostly relate to separation of the New Zealand micro-continent from Gondwana. The major structural controls on mineralisation at this scale, however, are associated with the volcanic arc processes responsible for the CVZ. Post-mineralisation faulting are linked to the Hauraki Rift and the Colville Ridge-Havre Trough system. Regional scale faults controlling the distribution of gold deposits are the product of these tectonic events; much of the faulting may relate to rifting and calderas, but further work is required to demonstrate this. Detailed study is also needed on vein systems at the prospect scale to validate models of brittle deformation responsible for such systems. Evidence that a variety of structural mechanisms dominated in different deposits is found at the vein scale, with Coromandel gold deposits being classified according to their different styles of vein-fill texture.

Jan 1, 1990

By Orr T. O H, Hodkinson I. P

The Mount Leyshon breccia complex is located on an east-west trending contact between Cambrian metasediments (Puddler Creek Formation) and the Ordovician Mt. Leyshon granite, within the Lolworth-Ravenswood block. Detailed mapping of basement, breccia and igneous unit geometries, crosscutting relationships and resolution of complex chronological relation- ships indicates that the Mt. Leyshon breccia complex should be reinterpreted as a number of intrusive igneous and breccia phases. This is in contrast to a previously published account of a largely extrusive geological setting. A complex structural history dominated by strike-slip faulting is preserved within the basement units and is responsible for controlling the location and geometry of the breccia complex. The breccia complex has been divided into brecciated "basement", "main pipe breccia" and an "interactive magma/breccia sequence". Main pipe breccia (the most voluminous unit within the complex) has been re-interpreted as an intrusive breccia, rather than an extrusive or vent fill as previously proposed. This is based on the following evidence: 1. the facies characteristics of the main pipe breccia, 2. the presence of a progression from cohesive basement through to mixed breccia, 3. minor basement block rotation during breccia complex formation, and 4. the partial structural control on the main pipe breccia. No unambiguous evidence exists for pyroclastic facies, although the fine breccia variant commonly contains "accretionary structures", very similar in appearance to those formed during pyroclastic processes. In view of 1. above, they are interpreted to be the product of particle accretion during upward movement of fragmental material, although an origin due to altera- tion cannot be completely discounted. heir occurrence in the main pipe breccia indicates that their presence within a rock unit is not necessarily diagnostic of nvroclastic nroeesses.

Jan 1, 1991

The first stage in process design for coal preparation is a study of the coal seam and its associated features followed by an examination of the mining method to.be employed and the coal market requirements. Normally benefication is based upon the differences in relative densities of the coal constituents and asso- ciated ash forming components. Since initial liberation is obtained at a relatively large particle size, the size to which coal is crushed is more subject to the market requirements than to liberation studies. It is possible to estimate energy requirements for comminution and recoveries and product grades can be cal- culated following the interpretation of standard laboratory tests. Numerous units are available for the separation and concentration of the components of run of mine coal in- cluding jigging, dense media separators, and for the finer particle size fractions, flowing film separators, dense media cyclones and froth flotation.

Jan 1, 1975

By Milawarma E, Cusack C

The Sapan Dalam coal deposit of Indonesia consists of ten steeply dipping seams with thicknesses varying between 0.1 and 3.5 m and split by shale, clay, silt and sandstone. The area contains four faults dipping about 75¦ with four to 85 m vertical displacements. The complex nature of the deposit coupled with limited 27 exploration drillholes at an average spacing of 200 m made it difficult to create a realistic geological model. A three-dimensional gridded seam model gave a fair representation of the deposit. Attempt to create an optimum pit using the WHITTLE 3D pit optimiser proved unsuccessful since the pit optimiser is restricted to standard regular or fixed blocks. The gridded seam model was converted to a fixed block model prior to the optimum pit design. Smoothing and pit base controlling were also introduced to obtain a smoother pit. A mining scenario produced 3.6 million tonnes of coal, 28.4 million bcm of waste and US$18.1 million revenue.

Jan 1, 1995

By Morrison R. D, Kojovic T

Industry-sponsored research at the Julius Kruttschnitt Mineral Research Centre has produced models of high tension roll and electrostatic plate separators operating in mineral sands dry plants. The behaviour of mineral species has been characterised under a wide variety of operating conditions by extensive plant machine sampling and laboratory measurements. The effect of operating conditions on separator performance has been quantified by monitoring changes in the weight distribution of mineral species along the product splitter axis. The response of each mineral species has been modelled on a size-by-size basis using an average surface charge decay time and a variation in its surface properties. The models incorporate changes in machine, mineral and ambient conditions on the separation and predict all product flows, assays and size distributions. This paper outlines the structure of the models. These models are being implemented in JKSimSand, an user-friendly simulation software Package.

Jan 1, 1991

By Coin CDA

From a study of coke samples obtained from the tuyere level of four Australian Blast Furnaces, the nature of in-furnace coke degradation has been investigated. At the periphery of the raceway is a concentration of fines and the lump coke appears dull and rounded. However coke from the deadman is angular and relatively undegraded. Cokes made from higher rank coal appear to suffer preferential attack of the reactive maceral derived component (binder). The coke from lower rank coal appears to be attacked non-preferentially by the solution-loss reaction. Initial attempts to simulate these phenomena have given results consistent with these findings. From chemical analysis of the tuyere probe samples there appears to be a relative increase in carbon and decrease in-.sulphur and phosphorous between stockline and tuyere level. An overall decrease in coke mineral matter derived material was noted and associated with this was a significant gasification of silicon. Consequent formation of silicon carbide was noted.

Jan 1, 1981

By Muchi I

To clarify the characteristics of non-uniform flow of gas through layered burdens of ore and coke, flow equations of continuity and motion were solved numerically taking account of the geometrical effect of a bed. The results are compared with that predicted by an approximate solution. A mathematical-kinetic model for determining the distributions of process variables over the region from the top to the melting level of blast furnace with the horizontal or the inclined layers of burdens is developed in consideration of the uneven gas flow. By the use of this model, the longitudinal and the radial distributions of process variables in an existing blast furnace in Japan were calculated with the aid of a digital computer. Computed results show that the process variables and the melting level change remarkably over the cross-section of the furnace and that the patterns of these distributions are similar to the results observed by other investigators.

Jan 1, 1975

Major discrepancies between mine estimates and estimates from plant metallurgical balances are a common problem in many gold and base metals mines around the world. Many existing practices are based on practical protocols that often fall short

Jan 1, 1998

By Katsuyama K, Nag DK

Three aspects of rock mechanics, namely, in-situ stress estimation by acoustic emission (AE) method, strength of rock mass and role of chemicals to reduce the strength are covered. It is possible to detect the previously applied maximum stress by stressing a rock specimen to the point where there is a substantial increase in AE activity. This is known as Kaiser effect. From the AE signatures in the second and subsequent loadings, AE take-off point was identified more easily than in the first loading. In determining the compressive strength of rock mass, two factors have to be considered, namely, the size effect on the compressive strength of intact rock and the effect of discontinuities on the compressive strength of rock mass. Although a modified Bieniawski criterion gives best agreement with the triaxial test data, modifications have been suggested to Hoek-Brown criterion due to its popularity. It is possible to reduce the tensile strength of sandstone by saturating it with weak chemical solutions made with dodecyltrimethyl ammonium bromide, polyethylene oxide and aluminium chloride by up to 30%. In the case of compressive strength, there is no appreciable effect. The possible explanation is that the chemical solutions produce an effect on the strength of sandstone only when the failure mechanism is dominated by tensile mode.

Jan 1, 1998

By West-Sells P, King J. A, Patel C

The Eskay Creek orebody is located in north-central British Columbia (Canada). The ore contains major gold and silver values and minor but economically significant quantities of zinc. The refractory nature of the gold necessitates a pressure oxidation pretreatment prior to cyanidation. After solid-liquid separation the oxidation solution can be treated by oxyhydrolysis for iron removal and cementation with zinc dust for noble element removal. The resulting solution, as obtained in pilot studies, contains 7 - 10 g/L Zn, 0.5 g/L Ca and 2 - 4 g/L Mg. Minor amounts of cadmium, copper and iron may also be present in the solution. Over 90 per cent recovery of zinc from Eskay Creek oxidation solutions could be obtained by four stages of zinc extraction with Cyanex 302 extractant (Cyanamid Canada Inc, Niagara Falls, Canada). Zinc was stripped from the organic with spent zinc electrolyte in two stages. A complete description of the bench scale and miniplant studies of the solvent-extraction electrowinning circuit follows. The behaviour of minor amounts of copper, cadmium and iron in the circuit is also Discussed.

Jan 1, 1993

By C Menzies

Hydraulic Monitor mining at Solid EnergyÆs Spring Creek Mine has proven to be a safe and effective method of extracting steeply dipping thick seams at production capabilities approaching one million tonnes per annum.   This paper traces the development of Hydraulic Monitor mining from its initial introduction into old workings at Strongman Mine, its refinement at Strongman 2 in shallow, thick and steep workings, through to its introduction into the deep, very thick seams at Spring Creek Mine. This last step of the progression came with all the added complications that come with depth, particularly flammable gas.   This paper will describe the various changes in mining conditions that dictated the performance of the monitor, how the mine layouts were changed to adapt, and the various operational systems that were put in place, to allow a safe and productive operation.

Jan 1, 2007

Australia is the Western world's largest producer of alumina, supplying one third of total needs. Western Australia's South-West has the greatest concentration of alumina production in the world, with a current annual production rate in the region of 6.8 million tonnes per annum, over 20 per cent of the total supplied to market economies. The value of this production in 1989-90 was 2.34 billion dollars, a very significant contribution to the economy of the State (1). This is despite the fact that the bauxite from the Darling Range is the lowest grade that has ever been commercially exploited, and despite the geographical isolation of the region. It is therefore of great importance to the National and State economies that this industry retain its competitive edge, particularly in the current times of economic downturn. One essential ingredient of this competetiveness is technology and innovation, which can be assured by the committment of the industry to an active program of Research and Development, with support from the public sector as Appropriate.

Jan 1, 1991

The provision of electrical power is an important consideration in project development. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of laking a supply from a power authority or providing local generation can then be considered. This requires additional defmition of the probable characteristics of the supply.The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was previously possible.The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for five recent Australian remote development projects indicate how some of these aspects influence the decision on power supply.

Jan 1, 1990

By Ennis P. C

The Mt Keith ultramafic intrusive extends for about 200 kilometres from Agnew in the south to Wiluna in the north. It forms the host for a number of nickel sulphide orebodies including Mt Keith and Honeymoon Well. Long fibre minerals are associated with the orebodies. The presence of these minerals impacts on the issue of tailings disposal from several standpoints, particularly the slurry beaching properties and dust generation from dry beaches. Central thickened discharge (CTD) is an innovative method of tailings disposal that involves stacking tailings in a low conical hill instead of storing them in cells. In appropriate circumstances this leads to savings in capital costs and operating expenditure. The method was introduced to Australia in 1981, and is currently employed at four operating mines, Elura and Peak Gold, both at Cobar in NSW, McArthur River in the Northern Territory, and Union Reefs near Pine Creek, also in the Northern Territory. It is the proposed method for Century Zinc and Ernest Henry, both in Queensland. The paper describes laboratory test work and design parameters for the application of the method to tailings disposal at Honeymoon Well and compares them with comparable data for other CTD systems. Of particular relevance for design purposes are beach slope, density, and water recovery. Wind tunnel tests were conducted on the Honeymoon Well tailings samples to investigate dust generation from the dry beach surface and it was concluded that dust generation from an undisturbed beach would not occur because of crusting.

Jan 1, 1996

Most orebodies have one or more boundaries which are gradational, where the decision to stop mining is based on an economic cut-off. To maximise profit, this cut-off grade must be chosen correctly. It is necessary to review cut-off grades regularly, as the optimum cut-off grade changes with time, and major changes are hard to implement in a working mine without disruption to production schedules.Whenever a cut-off grade is used, there will be errors in its application caused by errors in the estimation of block grade. These can be minimised by stringent quality control in sampling and by the use of kriging, which attempts to minimise the absolute errors in grade estimation. The kriging method used should produce the most accurate estimates of marginal grade blocks - this will not necessarily be the technique that gives the best overall prediction of head grades.

Jan 1, 1993