Search Documents

By D Craw

A glasshouse experiment was set up to investigate arsenic uptake in rye corn grown in different arsenic rich substrates. Sods of material were taken from various locations and planted with rye corn seeds. The plants grew for 13 weeks after which time the above ground biomass was harvested. Analysis of the rye corn plants showed a narrow range of arsenic concentrations, which did not reflect the arsenic contents of the soil. Comparison of the results from this study with previous work showed the glasshouse rye corn to have lower arsenic concentrations in above ground biomass than rye corn grown in field conditions. The environmental conditions present on the tailings and water-rock interactions were considered the main factors involved with the difference in arsenic uptake between field studies and the glasshouse study. This suggests that bioavailability processes are influenced by a variety of factors and cannot necessarily be predicted by the use of soil factors or glasshouse trials alone as is often done when planning phytoremediation work and mine shut down.

Jan 1, 2007

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

Financial markets are subject to constant change and project finance, as a product within these markets, adapts and will continue to adapt with those changes. A meaningful discussion of these adaptations requires an understanding of differences between non-, limited and full recourse project finance. The reasons sponsors seek and lenders provide project finance are also pertinent in this context. Arranging a project, financing package can be a canplex and time consuming task. An important first step is choosing the right advisor for the assignment and then structuring and tailoring the financing before approaching prospective lenders. The last thirty years has seen changes in the needs of sponsors and the ability of lenders to meet them. These shifts in preference may well be a guide to the future. Several major project financings successfully canpleted in Australia in the last few years and more recent examples are broadly discussed. Project finance will be keenly sought in the future and the form and nature it takes will continue to vary.

Jan 1, 1983

The Taupo Volcanic Zone in New Zealand and the Philippine Mobile Belt in the Philippines are characterized by active subduction, active volcanism and high seismicity. The main factors affecting characteristics of geothermal systems in both countries are: tectonic setting, source magmas, maturity of the systems, and depth to the degassing magma body. Within New Zealand, geothermal systems are grouped into arc- and rift-type. Fluids in arc-type systems contain high amounts of volatiles (40%) and higher Cl contents (3,000-10,000 mg/kg). Maximum temperatures are also higher, reaching up to >400¦C. Arc-type alteration assemblages in New Zealand and the Philippines are similar. Because Philippine geothermal systems are less mature, have higher temperatures and steeper geochemical gradients than New Zealand ones, advanced argillization is more widespread occurring down to depths of 2000 m. Mineral phases are more varied due to the active input of magmatic waters and the formation of vapor conditions at depth, forming P04-, B-, Li-, Ce-, F-, and Cl-bearing minerals at high temperatures. In the Philippines, high temperature magmatic-hydrothermal to contact metamorphic assemblages containing biotite, amphiboles and pyroxenes are relatively common, but rare in New Zealand.

Jan 1, 1995

In late 1984, Council of the Australasian Institute of Mining and Metallurgy accepted a proposal to establish a Mineral Heritage Committee. This was to be involved in matters relating to mineral heritage-its recording, its preservation, and the acknowledgement that it can be of use to the mineral industry in the future. The Committee was established to ensure that all of the disciplines of our profession were included and that, so far as possible, all of our country as well as those countries of the Southwest Pacific Basin were represented. Some work has been commenced to bring real- isation of the importance of the heritage of our mineral industry to the forefront of the commu- nity's interest. There is not a state in this country and the Southwest Pacific where the mineral industry has not at various times proved to be the basis of community development.

Jan 1, 1987

In May 1977 a new dam was commissioned for disposal of 600,000 metric tonnes/year of tailings. Design basis, costs and construction problems are described. Problems arose, assoc- iated with lack of experience in building such a dam "from scratch". Solutions are described land costs given.

Jan 1, 1978

The history of the down draught Dwight- Lloyd system of iron ore sintering in Australia is developed. Characterisation of the broad process is given for one plant, and regional divergences from the reference practice are noted and briefly analysed. The subject of the development of high basicity sinters is introduced, and regional differences in approach and results are Examined.

Jan 1, 1972

Downhole survey uncertainties observed at various De Beers operations prompted an investigation into their possible effect on deposit shape and volume. An accurately surveyed artificial æboreholeÆ was constructed and different downhole survey instruments tested. In this way an empirically determined error range of 0.1 per cent to ten per cent was derived for downhole survey data. These survey errors were applied to an orebody model at an existing mine. Visualising the sphere of uncertainty associated with a borehole trace using a general mining package (GMP) gives an indication of possible volume variance. The resulting orebody maximum and minimum volume scenarios for three different depths (200 m, 500 m and 800 m) are presented. For certain instruments and borehole angles, the 3D positional error can be as high as 100 m at 1000 m down the hole. At depths below 200 m the resulting volume deviations can become significant for borehole survey errors exceeding 0.35 per cent. At 800 m depth the volume difference can approach 25 per cent. These figures assume that the error is compounded. The impact of these downhole survey errors is greatest for pipe-like orebodies such as porphyries and kimberlite pipes. Subhorizontal sill-like orebodies (and coal seams) will not be significantly affected by these errors. The impact of this type of survey error needs to be stated (and quantified) and is significant in JORC classification.

Jan 1, 2009

By E Giles

Pike River Coal Limited (PRCL) is opening a new underground coal mine in the Paparoa Ranges north-east of Greymouth. To access the coal reserves, PRCL have had to build a 13 km access road through regrowth and virgin forest, and appointed McConnell Dowell Constructors Limited, with URS New Zealand Limited as their consulting engineers, to construct the final access link: a 2.3 km long, 5.5 m wide and 4.5 m high incline tunnel. This paper discusses the logistical issues of construction in an isolated pristine forest in mountain land and how they were addressed. It provides an overview of the 90 per cent complete tunnel and how challenging rock conditions have been mastered. It outlines briefly the remaining work which is construction of pit bottom workings where the mine infrastructure will be housed and construction of a 110 m deep, 4.0 m diameter, vertical ventilation shaft.

Jan 1, 2008

From August 1962 to June 1976 Peko Mines Ltd. produced Gold Bullion at the Peko Control Mill using 18x24 Denver Mineral Jigs and strake tables. Gold ores treated during this period were obtained from Orlando, Juno and Ivanhoe Mines and from the Warrego Mine after 1974, all in the Tennant Creek Area of the Northern Territory. With the downturn in copper prices Warrego Copper ore mining ceased and the copper Smelter closed down in February 1974, Warrego gold ore continued to be treated in the Peko Concentrator.

Jan 1, 1978

By McGuckin P. H, Logan A. S

The BHP Minerals' Cannington silver-lead-zinc deposit is located approximately 190 km south-east of Mount Isa. The deposit, is hosted by Proterozoic rocks beneath a thin cover of younger sediments, and contains a total estimated resource of 45.3 million tonnes at 11.1 per cent lead, 4.4 per cent zinc and 500 g/t silver. The deposit is separated by faulting to form a shallow, lower grade Northern Zone and a deeper, higher grade Southern Zone (Roche, 1994). Contract development of an exploration decline to test mineralisation in the Southern Zone commenced with the excavation of a boxcut in August 1993. The complex variably deformed Proterozoic sequence interpreted from drill core and intersected in the exploration decline has required a high level of practical rock mechanics input to achieve: ò appropriate support designs, ò a high quality of installation, and ò required development advance schedules. The Norwegian Tunnelling Index (Q System) in conjunction with regular face mapping is used as an operating tool to assist in decision making for ground support. Line mapping, discontinuity analysis and wedge assessments are conducted routinely to optimise ground support requirements in the decline, intersections and all other underground excavations. Throughout the project, an emphasis has been placed on developing a strong working relationship with the contractor to achieve quality assurance program targets.

Jan 1, 1995

ABSTRACT' The first references to gold in New Guinea were by the Portuguese in 1525. The first significant discovery and gold rush was on Sudest Island in 1888 and was a natural extension of the rush that surged up Australia's eastern coast and ended at cook- town. Prospectors made a series of minor discoveries in coastal regions before the first large discovery at Wau/Edie Creek/Bulolo in 1925. Major post war gold discoveries were made at Bougainville, Frieda River, Porgera and Ok Tedi. On Misima Island a large bulk low grade deposit has been recognised surrounding old gold workings. Gold exploration has increased drama- tically since the lifting of a 3 year moritorium on new exploration areas in Noverrber 1982. A new bulk low grade gold discovery has been made on Lihir Island, north of Bougainville and a number of other promising areas are being drilled. Gold production is also expanding dramatically from current levels of 600,000 ounces to an anticipated 1.3 million ounces in 1985 with the opening of Ok Tedi. Other potential developments are likely to increase output above 2 million ounces by 1990. Papua New Guinea's world ranking as a producer is likely to move from 9th to 7th in 1985 reflecting the favourable geological potential, stable political environment and attractive development terms offered by the Government.

Jan 1, 1984

Shear strength testing of rock discontinuity surfaces has been undertaken at a considerable number of open pit gold mining operations in Western Australia, as part of geotechnical studies of pit wall stability. These mining operations are located in geological settings that are typified by highly weathered and/or chemically altered rocks that contain significant structural fabric in which accurate and representative measurement of shear strength is essential.Little of the published rock discontinuity shear test work and back-analysis of failures has been conducted on weathered discontinuity surfaces, at low normal stress levels which are comparable to Western Australian conditions. Available shear strength data are reviewed and the following aspects of shear strength testing are considered:ò the need for shear strength test work and the amount of testing required;ò review of laboratory testing methods and the quality of the results; ò presentation of the test results;ò discussion of the shear strength failure criteria; ò interpretation of the test results;ò summary of test results for a variety of rock types, degree of weathering and discontinuity surface conditions;ò a review of laboratory and field shear strength data to illustrate the amount of variability that can occur; andò a monitoring strategy is proposed to manage the uncertainty associated with discontinuity shear strength.

Jan 1, 1992

Brand se Baai, on the North-Western Cape Coastline of Southern Africa, is the site of the Namakwa Sands Limited Heavy Mineral Sands Mining Operation. The mine is a 14 000 000 tonnes per annum open-cast strip-style mining operation using truck and excavators to mine the sand. The orebody consists of relatively unconsolidated sands reworked by fluvial, marine and aeolian mechanisms. The total orebody includes three primary ore types, namely the Red Aeolian Sands, the Dorbank (a hardcap layer) and the Orange Feldspathic Sands, which forms the bulk of the resource. Mine planning and scheduling is done using a 50 m + 50 m variable bench height system with three primary bench heights. The Aeolian and Dorbank each have a bench that varies with their thickness of up to a maximum eight metres and the Orange feldspathic sand, a standard bench height of eight metres. For a number of years Namakwa Sands used a complex 2D, Datamine Based, macro system to perform the resource evaluation and mine design. As the mining operations expanded it became clear that a complete system redesign was required to cope with the increasing operational pressures coming to bear on the old system. The biggest challenges facing any replacement system are the sheer scale of the mining operation (16 km long and 7 km wide resulting in a minimum of 30 000 individual 50 m + 50 m mining blocks), the size of the geological data files (up to one gigabyte) and representing the benching system accurately (as the benches follow the topography and are not horizontal). In addition to these large-scale issues, the ability to run multiple mine design scenarios was required, an aspect which the old system was unable to perform adequately. Based upon these primary difficulties, a new business process was developed which required a complete rethink of the mine design methodology as well as the creation of a new system to deplete the resource model, produce monthly reconciliation evaluations and create a ultimate pit limit based on the operations mining cost model. Using a system based on the Earthworks Mine2-4D Mine Design and Scheduling System (with its mine design and scheduling specific tools), as well as a small, customised program, massive time-savings have been made. It is now possible to run several life of mine scenarios in the same timeframe that a single life of mine run took under the old system. This paper will present the methodology and business decisions behind the new Namakwa Sands system, and detail the restructuring and development used to deal with the large data set sizes and long processing times inherent in the old system. Future enhancements to the system that will make it more generically applicable to open-cast mining scenarios will also be dealt with.

Jan 1, 2003

Magnesium-rich olivine is used as an additive in LKABÆs iron ore pellets in order to improve the high-temperature properties of the finished products. Olivine is only added to the pellets that are manufactured for ironmaking in the blast furnace process. The olivine comes from Minelco/LKABÆs mine at Seqi in Greenland. This dunite complex of Archean age contains about 95 - 98 per cent olivine. The grain size is typically 1 - 3 mm but much larger euhedral olivine crystals are common in the porphyritic type. The serpentinisation is absent or weak. The most common minor minerals are chromite, chlorite, talc, phlogopite, amphibole and pyroxene. The crushed olivine is transported to LKABÆs pelletising plants in Northern Sweden. After grinding, small amounts of olivine are mixed with the magnetite concentrate. The concentrate is rolled into green balls, about 10 - 14 mm in diameter. The moist green balls are transferred into the pelletising machine where the maximum temperature is about 1250¦C. The residence time in the pelletising machine is about one hour. Olivine is used in order to get pellets with better high-temperature properties. This paper deals with the olivine alteration during the pelletising process and the behaviour of magnesium following the decomposition of magnetite. The reactions are quite complex in the pellets because the physico-chemical conditions vary considerably in the process from one process step to another, and in the pellet bed from the top to the bottom. Some olivine particles in the finished product show very slight alteration, some particles are completely decomposed. The formation of the iron-rich coronas around the olivine particles is the most typical alteration. In the finished pellets the magnesium is mainly distributed between the following phases: unaltered olivine, coronas, Mg/Fe-ferrite and silicate slag.

Jan 1, 2008

This paper describes operational experience with seam gas and spontaneous combustion management, gained during ten years of production history (1993 to 2003) in the Wynn seam at Dartbrook Coal mine. In addition, comparisons are made with more recent operational experience in the overlying Kayuga seam. Development and retreat longwall operations were undertaken in a 4.0 m thick working section of the Wynn seam, contained within the lower quarter of a circa 24 m thick mega seam, from 1993 until mining operations were relocated to the overlying Kayuga seam in 2004. Production from the first block of the Kayuga seam is currently underway with seam gas and spontaneous combustion management requirements being refined as further operational experience is gained. Seam gas management techniques, including pre-drainage with pressurised fracturing, surface to underground goaf drainage of a carbon dioxide rich seam gas and novel, high capacity ventilation circuits, were employed in the Wynn seam. Ventilation strategies included operating up to carbon dioxide STEL concentrations of 3.0 per cent in segregated return airways rather than being limited to the TWA-TLV concentration of 1.25 per cent. The spontaneous combustion experience at Dartbrook Coal has, to some degree, resulted in a change in the way the risk is managed in Australian coal mines. Values of carbon monoxide make and hydrogen concentrations are profoundly different from previously recommended management plan trigger levels and those used elsewhere in the industry. However, the detection of higher hydrocarbons together with rising oxygen depletion ratios and absolute hydrogen concentrations remain as indicators of advancing spontaneous combustion events. In this respect, experience gained in the Wynn seam was important in the initial management of the shallower Kayuga seam, an essentially greenfield site with no prior operational experience being available.

Jan 1, 2005

By L H. Chapman, I J. Kelso, N H. S Oliver

Utilisation of modern 3D visualisation tools, can improve our ability to correlate between different datasets, and thus to produce more accurate geological models. Here, we present an application of such techniques to the Century Zinc Deposit, northwestern Queensland, Australia. This stratiform orebody is the second largest Zn resource in the world (167.5 Mt at 8.2 per cent Zn, 1.2 per cent Pb, and 33 g/t Ag). It is hosted in the Page Creek Syncline affecting Mesoproterozoic shales and siltstones of the Wide Supersequence of the Isa Superbasin. As in other deposits, (eg McArthur River, Lady Loretta, George Fisher and Dugald River), the mineralised sequence is bound by an important regional structure, the Termite Range Fault, which partly intersects the deposit along its Eastern side. This fault is thought have been active during sedimentation and probably also during mineralisation of the lowest part of the Wide Supersequence. The anastomosing geometry of this fault system and crosscutting relationships with other NE trending structures indicate that it was reactivated several times from Mesoproterozoic to at least late Devonian times (>1000 million years in total); as a result, the ore sequence is subdivided into several fault blocks.Using two different computer modeling packages (GOCAD and 3ds max), we have reconstructed and restored the stratigraphic horizon with the highest Zn content, realised a series of isopach maps for each mine scale stratigraphic unit, plotted the three-dimensional distribution of Zn, Pb, Ag, Fe and SiO2, and have begun to evaluate the degree of correlation between thickness changes and sulphide zoning. With this approach it is possible to better understand the timing of mineralisation from a genetic perspective, because the origins of the orebody are controversial. Three-dimensional reconstruction is a vital tool for identification of syn-sedimentary and post-sedimentary fault activity. In conjunction with sulphide precipitation, these are factors that greatly influence the stratigraphic thickness distribution. Post-sedimentary deformation can be recognised directly by core logging and pit mapping, but the effect of tectonic movements during sedimentation (growth faults in particular), that represents a substantial variable when we attempt to reconstruct basin evolution, is difficult to evaluate without this methodology. The 3D models improve our understanding of the local basin architecture, identifying similar grade characteristics at different structural levels and thus suggesting that much faulting and folding are post-mineralisation events. In addition, we identified several growth faults adjacent to thickened layers, representing two possible sedimentary depocentres. These thicker domains apparently relate to the highest Pb content. If further analysis of rocks, thickness and grade distributions support this preliminary correlation, then a syn-sedimentary model for mineralisation might be applied, and would contrast with the sub-surface model for mineralisation of Broadbent et al (1998).

Jan 1, 2003

THE plant is one of the usual type of Mond plants, and contains no new features worthy of comment. A brief description of the process, however, with a few remarks on the working of the plant, may prove of interest.Producer gas is made by passing a mixture of air and steam through incandescent carbon contained in a furnace called a producer, which, in the Mond type, is a cylindrical casing of steel plate, lined with firebrick, and fitted at the lower end with sloping fire-bars'. Coal crushed to an even size (about 2-in. gauge) is elevated to bunkers over the producers, from which it is fed into a measuring hopper on each producer.The hopper is a cast-iron cylinder fitted with a swing cover at the top and a bell valve at the bottom, worked by a lever and balance weight. When a charge of coal is run from the bunker into the hopper, the cover is closed, and the bell valve is lowered, allowing the coal contents to drop into the producer. Thus no gas can escape from, or air be admitted to, the producer during the process of charging. The hopper discharges its coal through a steel pipe-shaped container called the bell, which projects about 9 in. through the roof of the producer. The function of the bell is to spread the coal evenly over the fire, and supply coal to any portion of the fire as it settles.

Jan 1, 1918

Response of a mineral to anionic and cationic flotation reagentsvaries with the nature of the mineral and the particle size. A ruleis deduced for the selection of the correct type of reagent, which leads to a simple method of testing ores to determine the possibility of separating the constituents by flotation.

Jan 1, 1963

Politicians and economists talk glibly about the so-called knowledge revolution. The reality is that knowledge is fundamental to economic progress. Consequently there have been many technological revolutions. The global impacts of the invention of the steam engine and the development of the frozen meat industry are well known. Another less publicised technological advance occurred in Central Otago late in the nineteenth century. This was the adaptation of the bucketladder dredge to the mining of placer deposits. A product of over 30 years experimentation and innovation, New Zealand dredging technology was taken to the Risdon Iron and Locomotive Works, San Francisco by R H Postlethwaite, a Dunedin based mining engineer. New Zealand-style dredges built by Risdon operated successfully in California, Alaska and the Yukon. Californian engineers assimilated the best features of the New Zealand dredges with American (Bucyrus) designs to produce a standard for the worldwide placer mining industry.

Jan 1, 2003