Search Documents

By Belton G. R

The kinetics of the interfacial reaction of H2O on liquid silica-saturated iron silicates has been studied by means of measurement of the HDO-H2 isotope exchange reaction. The apparent first order rate constant, ka, was found to be inversely proportional to the H20/H2 ratio, consistent with two electron (melt to adsorbed/dissociating molecule) transfer mechanism and can be given by the expression In ka = -1.97 x 104/T + 1.57 - ln(pH2O/pH2), where the units for ka are mol cm -2 s-1 atm 1. The results of the current study are shown to be consistent with the indirect measurements of earlier work.

Jan 1, 1987

By Eisele TC

Horizontal perforated-plate baffles were shown to improve the cleaning efficiency of a flotation column when processing coal from two sources. The baffles consisted of flat plates with holes large enough to avoid plugging problems, and they improved the washing efficiency by making the flow patterns in the column closely approach plug flow. Tests with varying amounts of baffle open area showed that the optimum was between 30 and 40 per cent open area, which effectively prevented backmixing without seriously reducing capacity. The baffled column had previously been tested under ideal conditions with good results (87 per cent pyrite rejection at 85 per cent combustiles recovery), and so the tests reported here were intentionally run with difficult-to-float coals to determine the benefits of baffling under adverse conditions. For an original coal feed containing 38 per cent ash and 3.23 per cent total sulphur, the baffled column could recover 84 per cent of the combustibles while rejecting 84 per cent of the ash and approximately 54 per cent of the pyritic sulphur. Without baffles, the column recovered 88 per cent of the combustibles while rejecting only 76 per cent of the ash and 45 per cent of the pyritic sulphur. Subsequent tests with a dye tracer showed that the baffles reduced entrainment by approximately a factor of five, while the recovery was reduced by only a few per cent. Overall, the loss of capacity due to the baffles was more than offset by the improvement in product quality.

Jan 1, 1993

By Hutchings SG, Skimmings T

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921

Recent and on-going studies on the leaching of gold, the properties and activity of carbon, developments in the elution of gold from carbon, and methods of recovering gold from solution are reviewed. Emphasis is placed on Australian contributions, and their impact on gold metallurgy. Consideration is given to the future development of selective solvent extractants, ion exchange resins or alternative reagents for cyanide.

Jan 1, 1987

By W A. van der Westhuizen

Selective mining played a major role in saving a mine and a communityÆs existence as well as creating a working culture that is the model for all KumbaÆs mines. The successes that resulted from selective mining led to receiving KumbaÆs highest award (it was the Gold Medal Breakthrough project of 2003) as well as the productivity award at the National Productivity Institute award ceremony in 2004. Kumba was established in November 2001 (previously Iscor Mining). The new company identified Mineral Resource Management (MRM) as one of its key drivers and an initiative was launched to define MRM in the Kumba way. Best MRM practices at the Kumba mines were included in the definition. Selective mining was born out of this initiative. One of the key principles of good MRM practice was identified as: æThere must be a balance in the operational processÆ. This principle was applied with great success at Thabazimbi Iron Ore mine in the Limpopo province, South Africa. The emphasis of this paper will be to show how value can be unlocked throughout the whole mining value chain. In the past (up to 2001) the mine went through a number of crisis situations: planned production performances were not reached, the stripping ratio was extremely high with two new pits, the product beds were not of constant quality, slope failures were big risks, flooding could and did cut off half of the ore supply, and restructuring demoralised staff.This paper focuses on: selective mining throughput drivers, and selective mining and its role in achieving this balance.The results were dramatic, with huge improvements in production results, stockpiles, plant yields and product bed specifications. The mine was brought into balance and a self feeding loop was created with positive spin-offs up to this day.

Jan 1, 2005

By Lee M. F

The Lady Loretta lead-zinc-silver mineral isation of north-west Queensland was discovered first by Placer geologists in 1968 as a result of a geochemical soil survey. The stratigraphic position, mineralisation and rock associations of the deposit are very similar to those of the Mount Isa lead-zinc-silver orebodies. Aspects of the exploration history, geo- chemistry and structural geology of the Lady Loretta deposit, are discussed. A geometric model of the Ore Horizon is given.

Jan 1, 1974

By A Mokhtari, S Gatehouse, N Rutherford

Geochemical exploration continues to play a significant role in new mineral discoveries inAustralia and elsewhere, including terrains where mineralisation is buried or otherwise obscured by regolith cover of various types. Transported regolith commonly restricts the migration of trace elements to surface, especially in arid terrains, presenting a range of problems for traditional geochemical exploration methods that employ surface samples. Regions dominated by transported cover include the northern parts of the Tasmanides in eastern Australia and the Yilgarn Craton which are variably covered by thick alluvium and Mesozoic to Cainozoic sedimentary rocks (Anand and Paine, 2002). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By I Gipps

The mining industry has come through a period of major change in community expectations regarding safety and environmental impact and these changes can be expected to continue in the future. These changes are ultimately reflected in Government regulations and industry safety standards and form the basis of the ælicense to operateÆ. Equally, advances in technology have made possible new equipment and processes either available now, or close to completion, that will allow mines to meet these more stringent expectations if properly introduced. Changes in technology provide opportunities for mine management to introduce new systems that will remove people from hazardous areas and lead to improvements in the ætriple bottom lineÆ. In a longer time frame of five to ten years, novel and advanced technologies that are currently being developed will deliver new mining methods and conversion of presently uneconomic resources to ore. This is consistent with the time frame required to develop a new mine from discovery. Strategic decisions can be taken now by mine designers to enable the introduction of these major technology changes. Examples of both practical and strategic opportunities are drawn from the integration of rock cutting/blasting, automation, electronic communications and new mining methods. This paper discusses emerging industry trends, changes to legislative framework and some practical choices for existing and imminent technology.

Jan 1, 2003

A general review of grinding mill steel liner evolutions/developments in recent times. The driving force behind these developments has been the mill operators desire to minimise the nett cost of their operation. These developments have resulted from a team approach between supplier, operators and reline crews. The move towards larger diameter high aspect mills, faster mill speeds, pebble ports and the use of large diameter grinding media has affected the traditional liner designs, which is placing higher demands on the supplier to meet these new working parameters and expectations. Operators are also taking closer ownership in the liners being supplied, as demonstrated by the development of their own mill liner specifications. This paper outlines some of liner developments and changes undergone at various milling operations around Australia and overseas (such as Cadia Hill, Kidston, Ok Tedi Mining, PT Freeport, etc) and where to in the future?

Jan 1, 2000

By Barro L

Very large reserves of gas are contained in coal. Because of the low permeability of the coal gas flow rates are very low. Fracturing of the coal can be achieved by use of the nitrogen - foam frac techniques described but the flow rates after fracturing are not sufficient to support economic development. Fracturing of the seams in the Bowen Basin was as predicted but in the Sydney Basin no trace of the fracture could be found when development proceeded past the fractured well. Testing of coal samples has provided some insight into parameters affecting desorption Rates.

Jan 1, 1982

By M Byrne, P Newman, M Lindqvist

SomincorÆs Neves Corvo Mine, one of the largest copper producers in Europe, is currently constructing a paste backfill plant in order to replace cemented rockfill in its bench and fill stopes and possibly replace hydraulic sandfill in the drift and fill stopes. A 250 m flow loop was constructed at the mine and the flow properties of various paste blends were investigated. Cycloned tailings and total tailings were both pumped successfully as pastes and were also combined with waste rock for additional testing. The pressure losses in 102 mm and 154 mm diameter pipeline were recorded at flowrates up to 60 m3/hr and are presented at slumps from 120 mm to 250 mm. The data showed the sensitivity of paste mixtures to slight changes in consistency, confirming the need for accurate control during paste production and distribution. The flow results clearly showed the different paste behaviour between cycloned and total tailings pastes and the change in properties at low and high slumps. In addition to pressure loss data, strength testing was done on 38 mm and 82 mm diameter samples. Further strength testing is ongoing at the mine using fly ash as a supplement to cement, reducing the overall binder cost. Preliminary engineering for the underground distribution system is briefly discussed, with reference to the siting of the plant. The Neves Corvo Mine is particularly shallow and alternative methods to pumping were sought in order to ensure sufficient hydraulic head for underground distribution. The comparison of options had to take into account the capital and operating costs, the operation of the plant and the impact on the future expansion of paste fill utilisation at Neves Corvo.

Jan 1, 1998

Knowledge of coalfield geology has evolved rapidly over the past few years. Recent advances ranging between exploration, mining geology and seam variation studies have enabled application of geological techniques commensurate with technological changes in the coal industry.

Jan 1, 1969

By Marshall K. I

THE problem of satisfactorily eliminating the fumes and dust which are unavoidably produced in various metallurgical and manufacturing industries is one which has received considerable attention in the past, and has been the subject of much investigation and research. The solution of this problem was urgently desired for two reasons, the principal one being the fact that a considerable percentage of the total process losses in many industries was represented by the commercial values of the fumes and dust that escaped from the stack.The other reason is that, in some instances, the emission of the matter is regarded as objectionable. Various methods have been designed with a view to solving the problem thus presented, and the latest development that has beendesigned is the process of electrostatic precipitation. Continued investigational and developmental work with this process has already demonstrated its applicability to many industries, and new uses to which the process can be put are being opened up. Its use is already widespread, and the economic success that has attended its application in most instances would indicate that its use will become more general in the future.It has proved its ability to treat gases over wide ranges of temperature, and has successfully handled various types of fumes whose chemical characteristics differ very considerably. In many processes it has now come to be regarded as standard equipment.HISTORY OF ELECTRICAL PRECIPITATIONThe first recorded observations on the influence of an electrified insulated wire on gases containing solid particles in suspension was made as early as 1824 by Hohlfeld, in Leipzig. He found that, if he electrified a wire hung in a bottle filled with smoke, the smoke cleared rapidly, and a deposit formed on the sides and bottom of the bottle.

Jan 1, 1923

A mining companyÆs approach to managing the risk of theft of explosives and initiating devices should be underpinned by an organisation-wide policy developed with internal and external consultation. It should be based on the principles of sound proactive risk management, planning, monitoring and remedial action. This paper aims to provide mining (and construction)organisations with the rationale and many of the tools they need to control explosive security risks. As with all legislative compliance, they are best managed by incorporating the statutory and legal requirements into company policies, management systems and plans, operating procedures and culture. This is the approach that has been adopted in this paper. Trends we should expect: more prescriptive legislation and stricter government regulations; enhanced enforcement and more prosecution; more sophisticated detection systems, eg airports; additional compliance costs; additional vigilance on record keeping; improved risk awareness and risk communication; wider use of explosives policies, management systems and plans; and additional security staff with investigative skills.It should be noted that mining companies will be required to play their part in reducing the likelihood of explosives, intended for mining purposes, being wrongfully used to threaten, hold to ransom or to injure individuals or members of the public or to produce property damage. This will be done by putting in place safeguards to reduce the risk of theft of explosives while they are under their control. On that basis, this is a business risk assessment rather than a hazard risk assessment. A conclusion of this paper is that mining companies can and should play their part in reducing the supply of explosive materials that can then be used for illegal activities. In fact, mining companies have always had this duty, but now the stakes are higher û æcomplacency no longerÆ.

Jan 1, 2004

By Cameron A

In recent years there have been significant developments in the tech- nology available for blast monitoring, analysis and simulation. Progress in these areas has been achieved through research conducted by explo- sives manufacturers and independent research groups from universities and mining companies. Miners are increasingly keen to exploit this tech- nology to help them design blasts which make optimum use of explo- sives to produce easily excavated muckpiles for the minimum possible cost. The art of blast design in the future will increasingly depend on an adequate understanding of the nature of the rock mass, the perfor- mance of explosives and the characteristics required of the muckpile to suit the chosen excavation machinery. Despite recent advances in blast simulation and the prediction of blasting performance, the best way to determine how a particular explosive will function relative to other explosives is to conduct properly designed and monitored field trials. This paper discusses recent work at Mount Thorley Colliery which demonstrates that field blasting trials can be monitored and analysed to provide quantitative data on the relative performance of bulk explosives. Techniques used in the trials included the sampling and analysis of explo- sives, insitu measurement of VOD, monitoring of near and far field vibra- tions, high speed and still photography and survey measurement of muckpiles. These techniques provided data for the analysis of throw, swell, fragmentation and burden movement together with data on the consistency and robustness of different explosive products. The blasting trials allowed both the shock and heave energy of various explosives to be observed in the field and led to the derivation of design rules for the use of differ- ent explosives at the mine.

Jan 1, 1988

Arrow Energy NL has been operating a number of coal seam gas wells in the Darling Downs region of Queensland. At the time of writing this paper, the region is enduring an extended drought period. The local aquifers are depleting and have not been significantly recharged in over a decade. The local communities (both rural and townships) are struggling to obtain water. Currently, coal seam gas (CSG) operators (under licence) draw water from the coal seams as part of the gas production process and the majority of operators choose to evaporate this water, as it is characteristically brackish to saline in quality and as such must be contained. Although the water produced from one CSG operator is not sufficient to drought-proof the greater area of the Darling Downs, there is potential to supply smaller local areas and contribute to the sustainability of these communities. This paper outlines the work completed by Arrow and its local community partners on the Darling Downs to date, and discusses the application of the produced formation water for:stock watering in feedlots, as a feedstock for coal washing, as a potable water supply for Dalby, as an agricultural water supply for cotton farming, and use as a medium for growing salt-water fin fish.

Jan 1, 2006

By Zhou Y, Karmis M, Haycocks C

Hazard analysis utilizes interaction mecha- nisms in combination with geologic, structural and mining conditions to delineate areas of potential damage in seams subject to interaction. Using characterizations of conditions peculiar to multi- seam mining, such as innerburden thickness, geol- ogy and structures, initial interaction contour maps can be constructed. Geologic hazard analysis is then carried out on roof, pillar and floor condi- tions in the affected seam using lower seam rock properties and layout geometries in the overlying seam. Either safety factors or damage ratings can then be developed representing degree of hazard in the lower seam. The final hazard map shows both the aerial extent and magnitude of potential dam- age from interaction.

Jan 1, 1992

Laboratory studies of batch and continuous screening of ferrous sinter mixtures (4-0.5 mm) are described. The results are analysed by an equation derived from the first-order rate law for the condition of decreasing screen residue.The results of the studies show that the two screening operations are comparable in all respects if deck length in continuous screening and time in batch screening are interchanged.It is shown that the general screening process is determined by the numerical values of the screening rate constants of each of the particle sizes in the feed mixture and that the relationship between these constants and the particle size/screen aperture ratios is related to the appropriate probability function of the same ratios.It is also shown that the screening rates decrease exponentially with the amount of near-mesh material present in the feed and that oversize particles can increase these screening rates for some screen motions and decrease them for others.

Jan 1, 1985

By Box JC

A comprehensive computer simulation has been developed for heap and dump leaching processes. It deals with complex chemical interactions, involving several minerals and reagents, which vary with time and location in the dump. The simulation is generally applic- able to ores of various metals extracted by different reagents. It requires only mineral- ogical data obtainable from drill cores and chemical data obtainable from the literature; there is no curve-fitting with adjustable parameters. Applications in designing testwork programmes, evaluating operating options, transferring experience to new situations and reducing uncertainty in long-term forecasts are described. Specific examples are included illustrating the potential of the simulation.

Jan 1, 1983