Search Documents

By G Anderson, V Lawson, P Voigt

Glencore operates zinc concentrators at both Mount Isa and McArthur River. Both orebodies have a history of complexity and required the development of new technologies to maximise the value from these long-life assets. The Mount Isa orebodies were plagued since operations started in 1931 with complex mineral textures making separation challenging and many areas uneconomic. Examples are given in Figure 1 with different grain sizes from the same orebody in different areas. The McArthur River deposit, located in the Northern Territory, was discovered by Mount Isa Mines geologists in 1955 (Logan, Murray and Williams 1990). The extremely fine-grained nature of the ore was quickly recognised and the difficult separation of the minerals was soon obvious. The geographical, metallurgical and economic factors resulted in the orebody not being developed until the technologies for the mineral separation had been developed. The development of the IsaMill allowed for an economic mineral separation flowsheet to be developed and ore treatment commenced in May 1995 (Nihill, Stewart and Bowen 1998). CITATION: Lawson, V, Anderson, G and Voigt, P, 2018. Developing technologies for a complex orebody, in Proceedings Complex Orebodies Conference 2018, pp 116–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J B Tucker, A T. McGrath

Situated in north-west Queensland, Australia, the Ernest Henry Mine (EHM) has been producing copper and gold since 1996. Owned and operated by Glencore Xstrata, ore is currently sourced from a newly developed underground sublevel cave (SLC) mine below the old EHM open pit (the pit). Ore feed to the concentrator is supplemented by satellite open pits comprising the Mount Margaret operation.The transition from open pit to a producing underground mine involved a complex extraction sequence for the first two production sublevels on RL1650 and RL1625. Underground mining during cave initiation was further complicated when south wall instability prevented completion of the final open pit shell. The transition mining phase included mass firing of an inclined crown pillar between the initial SLC void and the pit followed by a combination of transverse and longitudinal SLC mining.The inclined crown pillar mass firing was the first significant milestone in the extraction of the transition ore block. Comprising approximately 890 000 t of in situ material; 70 000 m of drilling was charged with 351 t of emulsion and 6026 electronic detonators to initiate the single mass firing. The firing contained five direction changes over 19 seconds making it one of the largest and most complex underground blasts ever conducted in Australia.Risk management was integrated into every facet of the technical and operational planning and execution of the transition mining phase, whilst maintaining daily mine construction and production commitments. This paper provides a detailed overview of the transition objectives and constraints, mining method selection, post mass blast outcomes and the journey ahead.CITATION:McGrath, A T, Campbell, A D and Tucker, J B, 2014. Transition of the Ernest Henry Mine from open pit to an underground sublevel cave, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 297–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A Maier, M Goldner, C Gimber

Given the ongoing global crises of climate change and nature loss, with the World Economic Forum (WEF) identifying them as the top risks to global economies in terms of both likelihood and impact in the coming ten years (WEF, 2022), there is increasing, pressing demand for companies to demonstrate they understand their climate and nature related risks and look toward contributing genuine beneficial environmental outcomes. Within the mining industry, mine closure is the obvious field in which climate and nature positive strategy can be linked with operations. To do so, there is a need to challenge long-held assumptions around closure in the mining and regulatory context; particularly, to shift the focus from closing individual mines to considering regional opportunity generation and value creation.

Aug 2, 2023

By J M. Menacho, L Zhang, A Hoadley, L Verdugo, B Etschmann, W Bruckard

Since the introduction of Lithium-Ion Batteries (LIBs) in 1991, the market for lithium-ion cells has been driven by the high demand for portable electronic devices and more recently for batteries for the electric car industry. It is expected to grow rapidly to reach 2600 GWh globally by 2030 (US Government, Office of Energy Efficiency and Renewable Energy, 2021). However, there is a desperate need to recycle LIBs to recover valuable cathode materials and graphite. For this reason, several physical and chemical recycling technologies have been proposed to recover these materials from spent batteries. Amongst these, froth flotation technology is a potential cost-effective technology for separation of the graphite fraction from the lithium oxide components due to the natural hydrophobicity of graphite and density difference between graphite and cathode materials (Folayan et al, 2021).

Aug 24, 2022

THE Taranaki oil-field is situated on the western side of the North Island of New Zealand, at about its widest part, and may be said to be the most compact and fertile part of the Dominion, for, with the exception of the. upper half of Mount Egmont and of the ranges adjoining, which absorb 36,000 acres, the whole of the area, miuus what is taken up by the rivers land streams-is suitable for settlement, and certainly two-thirds is good land. The gross area oE the district is 2,417,299 acres.The principle rivers are the Wanganui, Mokau, Waitara, Patea, and Waiwakaiho. Mount Egmont, which is 8260 ft. high, used to be called Taranaki, and from it the district takes its name (the Maori meaning of which is "sloping peak ").

Jan 1, 1911

To enable AN-FO .tòo' be used on an equal .weight basis wish Nitro Gl reerin.e expl3oòsives r smaller diameter bore holes became necessary With consequent modifications to drill steel and burden on holes, De't'onation of AN-FO "in small diameter holes proved successful' both with 'and without primer charges but some altorat-ions were required to. adopt Anolodeòr.s to the smaller -holes, Important factors in training all operators In the new charging method were the retention of imp-,cved, fragmentat'ion, avoidance of excel ive ove:break and keeping wall rock dilution 'to an absoluato mi. iArurle ò The ò successful storage of Ammonium 14t-rate in c"!ime.tic conditions 'with daily'.-' temperature fluctuationc above and below the critical' 90¦F, has. been "achieved,

Jan 1, 1964

By H Allday

The mining industry’s attention has shifted over the last decade with the recovery from the downturn resulting in greater development of innovation and new work methods in a bid to remain competitive and deliver higher productivity. The emphasis on cost reduction to improve profit margins has primarily been the focus of the “work smarter” campaigns embraced within the industry. But is this strategy holistically the best-for-business, or does it place a ceiling on revenue opportunities and inhibit mining companies from truly maximising value? Businesses need to maintain a balance between active cost management and revenue generation often resulting in cost reduction strategies at site level. These strategies have merit, assessing areas of cost wastage across operations and creating space for opportunity. However, this potentially can create distractions from the goal of enabling growth and lead to the sacrifice of quality and delivery. Focusing too heavily on cost reductions without addressing revenue generation is an unprofitable lens to look through, and the relationships between cost, revenue, quality and profit margin can often be overlooked resulting in missed opportunity to maximise value. How these relationships are effectively employed by mining companies to reap the rewards from an overarching corporate perspective down to site level remains a fluid concept depending on the nature, operating market and strategy of the business. A common directive from businesses to their operations is to strive for greater profitability and productivity. The quantification of these requirements, and the nature of the cascading message delivered, impacts the methods employed by the operational team to meet the expectations of the business. Cascaded strategies, if not delivered with appropriate participation and buy-in can often be perceived to be knee-jerk and create frustration for operations who are squeezed to deliver on expectations by slashing site costs. This squeezing is not only felt by the mining operation but at the individual level and can result in increased team stresses. In some cases, this may also steer behaviours towards activities that result in corner cutting and an elevation of operational risk, potentially increasing associated incidents and injury. Driving down costs by any means can create an unhealthy tunnel vision where value is no-longer assessed for best-forbusiness results. By flipping the viewpoint to a value-based approach revenue opportunity may be realised and potentially exceeded, however this opportunity may be missed if value is over shadowed by a cost heavy focus. By analysing a selection of real operational cases (ranging from mining contractors through to in-house mining giants), it becomes apparent that practical revenue maximisation strategies are not only key to an increase in value and cash flow but to a stronger understanding of business drivers for sites and operators alike. In the cases evaluated additional revenue opportunities are foregone in favour of cost reduction strategies resulting in negative impacts on the associated operations and wider businesses. Alignment towards value generation is king. If strategies are not implemented focusing towards value and revenue maximisation, the opportunity loss experienced by mining operations could continue be great and the question should be posed; when the next up-turn hits will operations be ready to reap the rewards or still have a glass ceiling above their heads?

Mar 15, 2021

By P Woodward, T Ly, N Muhamad

OZ Minerals' Prominent Hill copper-gold concentrator is located 650 km north-west of Adelaide in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a design capacity of 8 Mtpa. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell preceding the three stage conventional cell cleaner circuit.Since its commissioning, the Prominent Hill flotation circuit has been the focus of a series of projects aimed at continual performance improvement. This has been achieved by a systematic approach of project identification, evaluation and implementation which has led to a progressive improvement in flotation performance. Innovations that have been successfully implemented include aspects of cell design and operation, and reagent suite optimisation.Improvements to the mechanical cells initially focused on the installation of a modified rotor-stator design in the rougher circuit, as recommended by Outotec. Isolated cells were fitted with this technology and proven to provide a benefit for copper recovery before the design was trialled in subsequent cells along the bank. Based on this success, further modifications were made to other aspects of the rougher and cleaner cells.Laboratory trials conducted at Prominent Hill involve a screening process identifying potential reagents from a list of products, which are then rigorously tested in the laboratory before one is selected for trial in the concentrator. Where these reagents have demonstrated a statistical improvement in performance they have typically been incorporated permanently into the flotation circuit. This paper discusses the process of continual improvement at the Prominent Hill flotation circuit and the optimisation achieved by the implementation of key initiatives.CITATION:Woodward, P, Muhamad, N and Ly, T, 2013. Optimisation of the Prominent Hill flotation circuit, in Proceedings MetPlant 2013 , pp 431-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By A Turner, P Hills, D Johnson

Underground mining for gold began in Beaconsfield in 1877 and development of the Tasmania Mine saw the sinking of multiple shafts, including the Hart Shaft over the ensuing 35 years. The mine closed in 1914 at a depth of 455 m due to prevailing economics, eventually reopening in 1999. The modern mine closed in 2012 after extending the mine from a historical depth of 455 m to the exhaustion of the modern Ore Reserve at a depth of 1210 m. West Tamar Council took over the lease for the immediate area around the Hart Shaft as an extension of the adjacent museum. The Hart Shaft and above ground structures became a significant drawcard for visitors. Tasmania was affected by sustained wet weather during May, June and July of 2016 which caused severe flooding and significant Statewide damage. This uncharacteristically intense wet weather caused saturation of the ground surrounding the Hart Shaft. Eventual shaft failure was first identified in August 2016. The failure of the shaft occurred at approximately 50 m below surface and resulted in a plug of material completely blocking the shaft. Significant surface subsidence affecting the surface infrastructure ensued. Due to the unstable nature of the surrounding material, it was determined that addressing the failure above the blockage would not provide a permanent solution to prevent the continued flow of material into the shaft. Many options to stabilise the shaft were considered, however it was assessed that a concrete plug in the shaft in competent ground at a depth of 100 m below surface and well below the blockage, would provide the only long-term solution. Man-entry was considered unsafe. The solution to access ultimately entailed filling the entire shaft with granular fill up to 100 m depth to act as formwork for a concrete plug. The rising mains at 400 mm and 250 mm diameter, which remained in place in the shaft, provided the avenue for placing the fill and ultimately, the concrete plug. Once the plug was in place the remainder of the shaft up to the underside of the blockage and over the top of the blockage to the surface was successfully filled with a combination of more granular fill and flowable cement stabilised sand. The Hart Shaft and surrounding above ground infrastructure was successfully stabilised and re-opened to tourist access. CITATION:Johnson, D, Turner, A and Hills, P, 2018. Stabilising and filling the Beaconsfield Hart Shaft, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 42–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By D Olwagen, C Stanton, J Gerber

From December 2013 to February 2014 the Southern Middleback Ranges magnetite concentrator went through a successful optimisation process that included the installation of extra grinding power to treat a wider range of ore types. After the initial improvements, sampling surveys were conducted to identify the mineral deportment through the concentrator. Samples collected during the survey were analysed using X-ray fluorescence, quantitative X-ray diffraction and QEMSCAN™ to cross-validate the analysis. Certain streams were also put through a laboratory-scale Davis Tube Recovery washing process to produce clean concentrates for analysis. The QEMSCAN™ analysis identified various metallurgical characteristics (mineral association, particle sizes, grain sizes, particle densities, etc) and these were evaluated for each separation and comminution stage to both understand the processes involved and identify opportunities for improvement. Key findings from the investigation indicated the importance of understanding the elemental deportment of target elements throughout the various minerals. The standard practice of tracking iron deportment through assay provided misleading results on losses to tail through the plant. The investigation provided insight into both wanted and unwanted minerals and the efficiency of each separation stage. The efficiencies of separation are critical due to their impact on downstream capacity, and the investigation provided insight into where opportunities exist to extract more benefit. The findings of the geometallurgical analysis have been implemented on the concentrator, and improvements in the rejection of non-magnetic minerals have been seen.CITATION:Gerber, J, Stanton, C and Olwagen, D, 2015. Using geometallurgy during process optimisation activities at the Southern Middleback Ranges magnetite concentrator, in Proceedings Iron Ore 2015, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

Nippon Telegraph and Telephone Corporation (NTT) developed a new construction method (the M-2 method) that could drive a long, curved small-diameter tunnel (4>1.2 m) without human labor. This method employs the cast-in-place lining system, using quick-hardening resin mortar, so that it can greatly increase the driving distance and execute both long distance driving (longer than 500 m) and curved driving with a radius of curvature of 200 m. Furthermore, the central control system with a mini-computer in a vertical shaft enables all work in a small-diameter tunnel, i.e., excavation, lining, and transportation of excavated soil and materials, without human labor. NTT conducted several field tests and a Practical Application Test (P.A.T.) under a public road bearing great traffic. Good results were obtained and the practicability of this method was demonstrated. Therefore, from now on, NTT will apply this ii-2 method to drive telecommunication cable tunnels in urban areas. This method will also be applicable to constructing public tunnel facilities, such as for water, sewage, electricity and gas.

Jan 1, 1987

By N Guresin, M Rohde

A lead-zinc flotation tailings sample containing silver from BHP Billiton’s Cannington Mine has been characterised to understand occurrences of silver in the tailings by conventional elemental, X-ray diffraction (XRD) and size analyses followed by mineralogical analysis with a scanning electron microscope (SEM) equipped with mineral liberation analysis (MLA) software and the use of an adapted diagnostic leach process originally developed for gold containing materials.The tailings sample contained 67 g/t Ag, 1.8 per cent Pb and 0.52 per cent Zn. The XRD analysis showed that the sample consisted of 74 per cent silicates, nine per cent sulfides, 11 per cent magnetite and small amounts of other minerals such as fluorite, fluorapatite and rutile. The p80 and p50 of the sample were determined to be 106 µm and 38 µm, respectively. The silver distribution was high in the small size fraction with 52.1 per cent of the silver being in the -8 µm fraction. The silver minerals freibergite, acanthite, jamesonite, pyrargyrite and native silver were observed in the mineralogical analysis of the sample by SEM/MLA. The associations of the minerals were intricate and the occurrences of silver were complex. There were finely disseminated silver minerals and also coarser grains of silver minerals in composites with the host minerals. It was estimated that almost 50 per cent of the silver was contained in pyrargyrite, around 14 per cent as native silver and contained in acanthite, 12.5 per cent in galena and around ten per cent in freibergite and jamesonite.These composite particles and the type of the silver minerals present were expected to limit leaching efficiencies of the silver in hydrometallurgical processing. The diagnostic leach tests showed that around 50 per cent of the silver could be recovered by direct cyanidation and higher extractions could be achieved by more aggressive acidic systems.Cyanidation tests were conducted to confirm the findings of the diagnostic leach studies. The investigated cyanidation parameters were time (up to 48 hours), solid to liquid ratio (1:1 and 1:2), cyanide concentration (0.025 M, 0.5 M and 0.1 M) and particle size (p80 of 106 µm, 63 µm and 7.5 µm). The effects of oxygen and lead nitrate were also studied. The tests were conducted at atmospheric temperatures. The maximum silver recovery obtained was about 50 per cent for all the parameter ranges trialled except particle size. The decrease in particle size from 106 µm to 7.5 µm by fine grinding resulted in an increase in silver recoveries from 50 per cent up to approximately 82 per cent indicating that the liberation of the silver grains/minerals is one of the factors affecting the cyanidation recovery of silver in addition to the presence of refractory silver minerals not amenable to cyanidation.Low head grades of silver in the tailings and relatively low cyanidation recoveries of silver (without fine grinding) necessitate a thorough cost analysis for the cyanidation of the Cannington lead and zinc tailings to assess if cyanidation would be a suitable process option for the extraction of silver. It is clear that one of the most important factors in determining the cost feasibility will be the price of silver in the world metal market.CITATION:Rohde, M, Guresin, N and Johnson, N W, 2014. Characterisation of silver minerals in lead-zinc flotation tailings and their response to cyanidation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Blasthole cone samples are used for grade control in most of the iron ore mines of the Pilbara of Western Australia. This method of sampling is straightforward when the target sampling interval matches the mining bench height but is problematic when the blasted bench is 'flitch' mined in two or more passes. Crucially, the sampler needs to decide which part of the blast cone represents the upper and lower flitches to be mined. This sampling selection decision is usually made by assuming a certain proportion represents the subdrill component of a sampling face in a blasthole cone and the two flitches are split equally from the remaining portion. In this study of a West Australian channel iron deposit, sampling experiments were carried out to determine the actual proportions of a sampling face in a blasthole cone by spray painting the blast cones at flitch and subdrill boundaries during the drilling process. Measurements were then taken to assess the differences between assumed sampling face proportions and actual proportions. A set of paired samples was also collected from a number of blastholes with one set using the assumed proportions of each flitch for each sample, while the other set sampled the actual proportions, which were identified from the cone painting process.

Mar 1, 2010

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011