Search Documents

By Kavetsky A, Scott A

As well as breaking and moving rock, blast energy sets up a seismic wave in the ground which can cause significant damage to rock structures and buildings and disturbance to human occupants. This seismic ground vibration is potentially most damaging when its dominant frequency coincides with the resonant frequency of a structure, leading to high amplification factors between the input ground vibration and the resulting structural response. This paper outlines methods of identifying the resonant frequency of structures. It also describes a practical numerical method for the modification of blast designs to reduce the ground vibration energy in critical frequency ranges. The method is illustrated with two recent case studies.

Jan 1, 1990

By Moxon N. T, Berndt J. R

BHP-Utah Coal Limited's Peak Downs Mine is located in Cen- tral Queensland, approximately 200 km south west of Mackay. The annual raw coal production of the mine is over 8 million tpa, requiring the removal of about 40 million cubic metres of prime overburden. This is achieved through the use of five large draglines. The large depths of overburden (up to 55 metres) encountered over half the strike length of the mine enables cast blasting to be carried out in conjunction with draglines employ- ing the chopping method of digging. The objective of cast blast- ing is to use explosive energy to move as much material directly into spoil as possible. The additional costs of drilling and blast- ing are offset by reducing dragline rehandle. Two factors which are of primary importance to the design of cast blasts are initiation control and material velocity. High speed motion picture photography is a powerful diagnostic tool to quantify these aspects of blasting (Winzer, Montenyohl and Ritter, 1979; Chiappetta et al., 1983; Anon., 1983). The objec- tives of such analysis are to: 1. Determine the burden velocity, 2. Determine the time to initial movement (that is, the inter- val between a face hole firing and the initial movement of the burden), 3. Check the accuracy of the initiation sequence. BHP Central Research Laboratories (CRL) and Peak Downs Mine monitored a cast blast in the mine's Winchester Pit on 18 August, 1988. The objectives of this exercise were to: 1. Quantify current cast blast performance, providing a base case for comparison with modified blast design. 2. Compare two orientations of angled holes within the blast. 3. Assess the effectiveness of cast blasting utilising an air-deck. 4. Check blast timing with respect to burden movement times.

Jan 1, 1989

By Cotton P. L

Although the terms "pipe" and "tube" are normally considered synonymous, a distinction is often drawn, the former term being applied to the hot finished product and the latter to cold finished material. It is, considered that the title of this paper includes hot finished seamless, and continuous-weld pipe, cold drawn seamless tubing, and electrically welded tubing.The continuous-weld process will be reviewed first, passing to the various methods of seamless manufacturing, which, in addition to meeting the demand for hot finished seamless pipe, also supply the raw material for cold drawn tubing, the manufacture of which will then be described. Finally the electric resistance-weld process will be Considered, and the paper will conclude with a brief review of the processes described and trends in present-day manufacture.CONTINUOUS-WELD PIPEThe raw material for this process is delivered in the form of coiled, hot finished, strip steel, generally referred to as "skelp". The end of one coil is electrically buttwelded to that of'the next, so forming an unbroken strip. This continuous ribbon of 'steel is fed into a skelp heating furnace, and brought to the correct temperature for the forming and welding operations which follow. This temperature is usually about 1,350°C.The heated skelp issues from the furnace into 'a multistand mill, in which the first pair of rolls is designed to form the skelp into tubular shape, the edges being in close proximity to, but not touching each' other. These edges...

Jan 1, 1951

The Blackwater Coal Mine is a modern open cut operation using large draglines for over- :)urden removal and shovels, loaders and trucks to mine and haul coal to the crushing and coal ?reparation plant. Operations at the mine are described in sequence following through overburden removal to the railing of product coal from the mine site. The close operating connection between the mine and washery, which results from the blending of raw coal into clean product via the qashplant bypass system, is stressed. Some features of special interest at Blackwater Mine, such as land reclamation and slope stability,are outlined.

Jan 1, 1974

Recovery of tin and copper from concen trates containing cassiterite, stannite and chalcopyrite was studied in laboratory-scale tests designed to simulate continuous operation of the matte fuming process in which tin is recovered as SnS fume while copper accumulates in the matte. Charges made up of 300g of mixtures of the concentrate and siliceous flux were added at a uniform rate in pelletized form to crucibles containing 300g of matte and 50g of slag (both of which were recovered from previous tests), while blowing through the matte with air or oxygen-nitrogen mixtures at a rate of 3 to 5 1/min. Accurate material balances enabled the effects of process operating conditions on tin recovery and sulfur utilization to be deter- mined. When operated correctly, the matte fuming process gave tin recoveries exceeding 90 percent in spite of wide variations in the copper content of the matte and in the operat- ing conditions. Deterioration of tin recovery was associated with undersaturation of the slag with respect to silica, and with high partial pressure of sulfur dioxide (greater than approx- imately 0.2) brought about by oxygen enrichment of the blowing air. The utilization of sulfur varied widely in low grade mattes. Copper in excess of approx- imately 10% promoted formation of SO2 by the commonly accepted reaction: FeS + 1-120 2= FeO + S02 while in copper-free and lower grade mattes a substantial fraction of the oxygen was consumed in the alternative reaction FeS + i 02 = FeO + z S2.

Jan 1, 1980

This paper briefly discusses the negotia- tion of the more important provisions in agree- ments for exploration and mining rights with Pacific countries. LAND RIGHTS Land rights are complicated and sometimes controversial in many of the Pacific countries. In some countries, a company will have to deal with land owners directly; in others, the government will act as intermediary. Inevit- ably, a company will have to deal with both. Mining companies need to be sensitive to the culture and particular interests of the land owners and of their history in defending their rights. The issues are too complicated to be dealt with here. Some mining companies have spent, and will continue to spend, considerable time trying to understand them. It will " require patience, perseverance, sensitivity and unflagging optimism. The better advised companies will ensure that their local repre- sentatives get to know the land owners, under- stand their concerns, and will pursue a policy of keeping them informed on a regular basis of all of the company's activities and proposed activities. Good community relations are the keystone for good mining operations in the Pacific. Most countries will require the submission of an environmental impact statement so that they will know in advance what effects a pro- posted mining operation are expected to have on the environment and how it is intended to deal with them. They will also want to approve the company's environmental reclamation and rehabilitation plan. Let's face facts right away - mining, by its very nature, is not going to improve the environment. There will be waste discharges, emissions and deposits. They will affect the land, air and water and hence human, marine and animal life and vegetation. There will be sounds and odours and the esthetics of mining operations, though perhaps pleasing to geolo- gists and mining engineers, will not please Others.

Jan 1, 1987

The problems of the as-built water supply system are discussed. Recent modifications to the collection dams and the water cleaning station using wedge wire screens to resolve these problems are outlined.

Jan 1, 1978

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

By Bedford D. J

The post pillar cut and fill stoping method has been adopted by King Island Scheelite for the extraction of the main Dolphin orebody. The orebody is a massive, tabular deposit varying from 10 to 50 metres in thickness, and dipping at approximately 30¦ towards and under the sea bed. The mining method was selected for 1. maintenance of hangingwall support under the sea bed; 2. maximisation of first stage ore extraction; 3. flexibility of mining, allowing maintenance of grade and selective mining around waste bands within the orebody, and 4. compatibility of existing equipment both with stoping and the on-going underground mine development programme. Stope parameters were established on the basis of initial rock stress analyses, and since the undercut phase of mining the stoping programme has been monitored with various types of deformation measuring devices installed in a series of large diameter boreholes.

Jan 1, 1977

This paper details successful implementation of a revolutionary pit access system involving excavation of an 'in-the-wall' ramp at Three Mile Hill open pit operated by Gold Mines of Coolgardie, formerly Goldfan Limited, at Coolgardie, Western Australia. Three Mile Hill is a medium-size, open pit, gold operation typified by hard, competent, fresh rock conditions from near surface. The project involved construction of a haulage tunnel or decline access located in the wall of an open pit in place of a conventional pit access ramp. Works undertaken as discussed herein included excavation, support, ventilation, dewatering, services installation, commissioning and monitoring. Prior to implementation, the conventional hardrock pit slopes and designs were constrained by the presence of infrastructure and a main road to the North and by adjoining leases to the Southeast. The combination of these factors and economic considerations resulted in a decision to proceed with an innovative in-the-wall ramp access system that is believed to be the first of its type in Australia. Back-analysis indicates that implementation resulted in a cost saving of as much as A$3.6 million and increased mineable pit reserves. The paper deals with the successful implementation and operation of the in-the-wall ramp haulage as well as an economic evaluation that is aimed at drawing some general conclusions on favourable conditions for implementation in other mining scenarios.

Jan 1, 1996

This paper examines the impact of the time value of money on the location of mining facilities, as examplified by a central processing plant serving several mines. Three approaches, the Euclidean-Distance Approach, the Gravity Centre Approach, and the Rectilinear-Distance Approach, commonly applied to a single facility location problem were employed in the study. The objective function in all three models was the updated value of the following three costs influenced by the processing plant location and defined within the framework of the continuous model of value representation and the continuous interest rate convention: I. the costs of transporting the useful mineral from the mines to the plant, 2. the costs of constructing the transportation links between the mines and the plant, and 3. the costs of maintaining these links over time. Results of the study show a substantial impact of the time value of money on both the processing plant optimal location and the opportunity cost of neglecting the time value of money in the locational considerations.

Jan 1, 1995

By Warren L. J

The recovery of phosphate minerals from the Mt Weld deposit by froth flotation has been studied by many researchers. Most of the flotation experiments were carried out with a tall oil fatty acid as collector and sodium silicate as dispersant and gangue depressant at pH about 10. Several rougher stages and cleaner stages and, sometimes, a desliming stage were included. The major difficulty was to reduce the Fe2O3 impurities in the concentrate to the required level. We used QEM*SEM (Quantitative Evaluation of Materials by Scanning Electron Microscopy) to provide a comprehensive and accurate mineralogical analysis of the flotation products. The analysis indicated that the Fe2O3 impurities were mainly recovered in the second concentrate, owing partly to the incomplete depression of the liberated iron oxides by the sodium silicate and partly to composite particles containing iron oxides. The selective depressing action of sodium silicate was improved by adjusting the variables such as the modulus (SiO2/Na2O), pH and time of standing of the stock sodium silicate solutions or by adding some polyvalent metal salts into sodium silicate solution. The flotation process was optimised to produce a phosphate concentrate with the required grade and recovery (38.6 per cent P2O5, 2.67 per cent Fe2O3, 13.7 for P2O5/(Fe2O3 + A1203), at P2O5 recovery of 81.5 per cent). The possibility of recovering the rare-earth phosphate, monazite, from the Mt Weld deposit by flotation was also studied.

Jan 1, 1991

By Corrans I. J

A wide variety of copper-bearing gold ores exist throughout the world which have yet to be processed economically for gold recovery. The copper minerals present in these ores can be many and varied and usually result in high cyanide consumptions and problematical levels of copper in leach solutions. The copper content is often assessed as being of nuisance value as the ores are generally of the grade or type which can support neither a copper project nor a straight gold project, due to the interference of copper. Many of these problematical gold-copper ores could possibly be processed economically for gold recovery using a novel ammoniacal cyanide leaching system which utilises a copper-ammonia-cyanide complex as an effective lixiviant for gold, yet limits copper dissolution and conserves cyanide. Results from recent testing have promoted a re-evaluation of the economics of treating some gold-copper ores. This paper describes the novel leaching process and discusses the conditions employed to treat a variety of gold-copper ores.

Jan 1, 1992

By Borshoff J, Coles R

The Rum Jungle Uranium Province is lo cated on the western margin of the Pine Creek Geosyncline approximately 60km south of Darwin. Uranium was discovered in the Embayment area (Whites Deposit) in 1949, spurring active ex- ploration and leading to the discovery of the Rum Jungle Creek South Deposit in 1959. With the discovery of the Alligator Rivers Uranium Field, new criteria in the understanding of the controls for mineralization sparked a re- surgence of exploration activities in the Rum Jungle area. Uranerz Australia Pty. Ltd. (UAL) commenced exploration in the area in the late 1970's in joint venture and in its own right. Two domal Archaean granitic complexes, the Rum Jungle and Waterhouse Complexes, domi- nate the area. They are unconformably mantled by Lower Proterozoic sediments metamorphosed to middle to upper greenschist grade. The Lower Proterozoic sediments are unconformably over- lain by remnant blocks of Carpentarian sand- stone, generally preserved in downfaulted blocks. Over a six year period extensive geolo- gical, geochemical and geophysical programs were conducted to reinvestigate previous target areas and locate new prospective zones. Exten- sive shallow bedrock drilling showed that lo- cally the stratigraphic succession is quite variable and cannot always be divided into an ordered succession for correlation with groups and formations established by the Bureau of Mineral Resources (BMR). Deformational events resulting in intraformational recumbent folding and overthrusting also account for repetition of certain lithotypes.

Jan 1, 1984

By Landy D. M, Ward M. O, Power W. L

Geological structures are irregular and intricate, so creating a 31) solid geology model is a complicated process. A software system can only partially automate this process, since geological knowledge and experience are required. Therefore, the interaction of a geologist is critical for such a system. This paper discusses some useful advanced functions for enhancing the visualisation and manipulation of 3D solid geology models: flexible attribute display, multiple views, auxiliary display objects, and geologically sensitive operations. It also describes some experiments to explore the effectiveness of these functions and presents sample output. Most existing 3D solid geology modelling systems are implemented in an ad hoc way, which greatly reduces their reusability and extensibility. This paper presents a generic framework for 3D solid geology modelling systems, which is based on object-oriented technology. The deficiencies of current systems may be improved by using this generic framework. A modelling process based on drillhole data is discusses as a case study.

Jan 1, 1995

By Spottiswood DJ, Kelly EG, Bull WR

An empirical model of a 254mm water-only cyclone treating minus 17001im coal has been developed. The model includes the prediction of by-passing, SG50 corrected, water split and the use of a single equation forthe reduced performance curve of particles in the range 1700-106pm. Particles finer than 106pm did not separate according to specific gravity. Simulations using the model showed the water-only cyclone performance to be dependent more upon feed size distribution than washability when the feed contains high-ash fines, but that, with a deslimed feed, the yield and ash content of the over-flow should be controllable by altering feed rate or feed pulp density.

Jan 1, 1985

By Tarvainen M, Mattila O

Outokumpu Oy has systematically developed the automation of mineral flotation covering the technology of both new devices and control methods, and as a practical result of this effort currently produces two on-stream X-ray analyzers. The Courier 300 system basing on conven- tional X-ray technology is applied to complex or large processes. The newer Minexan 202 dis- tributed probe system based on radioisotope technology is developed mainly for simple or small scale applications. In this paper aspects and experiences of these analyzer systems and their applications for flotation control are discussed with particular reference to the role of the computer

Jan 1, 1977

By Ward C. W

Conventional polygonal and block modelling techniques inadequately represent the grade-thickness distribution of some narrow shear and stratabound gold deposits. The polygonal influence of high-grade drill intercepts can result in overestimates of resource tonnages at high-grade cut-offs. Although block modelling methods provide grade smoothing and a better representation of structural continuity, the technique can lack precise definition of ore width. An alternative method known as Spatial Object Modelling (SOM) has been developed on MineMap software to overcome some of these modelling issues. This method does not rely on a uniform cell size and allows grade smoothing between resource intercepts in three-dimensional space. The SOM technique creates grade-thickness bars on regular, user-defined spacings which allow easy visual comparison of raw intercept data to the interpolated model. Model cell values are readily transformed into isopachs, isopleths and resource perimeters for reporting and mine planning purposes.

Jan 1, 1997

The Devonian Mount Morgan gold-copper deposit was situated on the western margin of the Calliope Volcanic Are assemblage, in the northern New England Orogen. Recorded production from commencement of mining in 1882 to mine closure in 1989 stand

Jan 1, 1994

During the last few years the quality requirements on roads and railroads have become more accentuated due to the desire to minimise maintenance costs. This has, in turn, led to increasing requirements in the preparation of ballast materials and pavement aggregates. As the access to natural gravel in northern Europe is decreasing (due to lack of availability or by law restrictions) the use of crushed rock material is becoming more and more important. The aim of this paper is to derive and describe a universal method for the prediction of particle size distributions from compressing crusher machines such as jaw- and cone-crushers. Based on a closely defined physical model, expressions which define the size reduction process are derived. Conditions for simplifying assumptions are clearly outlined. The choice and mix of breakage functions is a central subtopic iò the analysis of the crusher machine processes. Known breakage functions are reviewed and evaluated. A new concept for determination of a true breakage operator which is related to physical properties of the crusher device and the size distribution of the feed material is introduced. Finally experimental tests are compared to numerical calculations. The method described in the paper can be a useful tool when designing crushing plants or when optimizing the output of compressing crusher Machines.

Jan 1, 1995