Search Documents

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R W. Shaw

The MTM Process targets treating lower grade and/or problem concentrates that are not attractive to smelters. The process has been developed at laboratory scale for copper and is based on a related development for zinc that has been extensively developed both in the laboratory and through pilot testing. The basis of the process is novel ammonia-ammonium chloride leach chemistry adapted to give high copper extraction whilst being selective over iron, arsenic and many other elements. The preferred flow sheet depends on location, especially infrastructure and utilities. These impact upon the leach and crystallisation stages more than copper reduction.

Aug 24, 2022

By K Faure

At Sams Creek a peralkaline granite porphyry dyke hosts gold-bearing sulfide-quartz-siderite veins. The granite dyke intrudes Ordovician-Silurian metapelite and quartzite, and has thin lamprophyre dykes along its contacts. The mineralised veins and the granite and lamprophyre dykes have been deformed during several phases of folding, the youngest of which is Early Cretaceous. The granite has been hydrothermally altered, with early magnetite-siderite¦biotite alteration overprinted by sulfide and quartz-siderite veins and quartz-perthite-albitesiderite-pyrite-rutile¦sericite alteration assemblages. The sulfide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, with minor quartz and siderite. The gold contains significant silver (up to 30.8 wt per cent) and ranges in fineness from 692 to 844. Immiscible liquid-rich fluid inclusions, in quartz protected from recrystallisation by enclosing arsenopyrite, contain carbonic liquid that homogenised at temperatures of 320 - 355¦C. The Sams Creek gold deposit is distinguished from the orogenic gold deposit type by its stockwork veining, magnetite-siderite¦biotite alteration, high sulfide content, ore mineralogy and the absence of mineralisation in the metapelite country rocks. Features of the Sams Creek gold deposit do not fit neatly into existing classifications of granite-related gold-bearing deposits. The peralkaline composition of the Sams Creek granite and the absence of molybdenite and paucity of chalcopyrite, are major points of difference with gold-rich porphyry copper deposits. The presence of a lowsulf idation-state ore mineral assemblage, carbonate alteration and carbonic fluid inclusions at Sams Creek are typical of many of the reduced granitic intrusion-related type of gold deposit. However, notable differences are: the reduced type granites are metaluminous and calc-alkaline; and Sams Creek only has high As in contrast to elevated Bi, W, As, Mo, Te, and Sb in the reduced type. The Sams Creek deposit also shows affinities with gold deposits associated with alkaline magmatism, and it appears to be a new variant of this type as an As-Au deposit associated with a peralkaline granite and lamprophyre.

Jan 1, 2004

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By M R. Drumond

The present work presents a new theoretical interpretation of the flotation process, which can also be applied to other mineral processing physical unit operations. This interpretation is part of the æModelo OperacionalÆ (Operational Model) that was developed as an attempt to establish a new theoretical basis for mineral processing unit operations. In the case of flotation, a book was edited by one of the authors in Brazil (Mass Concentration by Froth Flotation, in Portuguese and Spanish).The model establishes a link between a natural phenomenon (migration of particles from the pulp to the froth) and a real industrial phenomenon (mass concentration by operational interference). In this model, flotation is viewed as a phenomenon of macromolecular mass transport (of particles) between froth and slurry phases. Mechanisms for mass transport and particle flow between phases as a function of the hydrophobic potential in each phase are discussed. By establishing the so-called equilibrium distribution curve between phases it is possible to calculate macroscopic balances that are related to metallurgical results, which in turn are a function of the operational line that is required by the process itself. The number of cleaning stages and their efficiencies can also be determined by simple laboratory-scale experiments.

Jan 1, 2005

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

It is a sad commentary on human nature that for every successful, unscrupulous entrepreneur you need a multitude of incautious, greedy investors. One wonders whether is will be ever possible to completely protect investors from their reckless gambling instincts, which are so widely encouraged elsewhere in society.

Jan 1, 1989

By A Seneviratne, Y Li, N Udugampola, X Ai, B Li

LoRa (Long Range) is a low-power, long-range wireless communication technology that has gained significant research interest for its potential use in multi-hop linear wireless sensor networks (LWSNs) for underground mines. These networks deploy LoRa-enabled sensor nodes in underground mines, together with LoRa repeaters placed along mine tunnels to relay sensor data to a LoRa gateway, which connects to a backend network for application-level processing. Since the packets generated by sensor nodes farthest from the gateway have to hop through many repeaters, their probability of successfully reaching the gateway is significantly lower due to the higher chance of packet collisions compared to sensor nodes closer to the gateway, resulting in a lack of network fairness for the sensor nodes. In this paper, we first present an algorithm to improve the fairness of a LoRa LWSN by grouping neighbouring nodes and adjusting the number of packet re-transmissions and transmission intervals for each group. Then, we demonstrate that the fairness of a simulated LoRa LWSN can be improved by approximately 500 per cent by applying our algorithm. We verify our algorithm with network simulations under different network traffic levels and grouping strategies, obtaining fairness improvements in each scenario. Our algorithm and results will pave the way towards developing highly fair LWSNs for underground mining applications.

Sep 1, 2024

By S G. Gatehouse

Extensive gold mining activity û dominantly alluvial û has taken place in the Sofala-Wattle Flat district since the 1850s.This work will have located most, if not all, of the visible sources for the gold in current stream systems.Also, there are many gold bearing elevated Tertiary alluvial terraces in the district which may confuse possible gold signals from primary hard rock sources in the streams.Associated element signatures eg As and other chalcophiles, will discriminate non-alluvial signatures but will not necessarily distinguish non gold bearing mineralisation.Both trace elements and conventional gold analyses will dominantly re-identify known occurrences. Conventional BCL sampling is considered misleading as experience from the Oberon area to the south of Sofala demonstrated that BCL sampling was very sensitive û perhaps too sensitive.All occurrences û major or minor û of gold will be detected (Gatehouse, 1992). To improve on BCL sampling, a small, -120# sample with selective duplication was recommended to screen coarse-grained gold anomalism and a program of sampling covering an area thought to be prospective was enacted.Samples returning anomalous Au were analysed in duplicate and if the results demonstrated reproducibility, indicating fine gold only, the sample site was assigned a high priority.It was found that most of the reproducible samples clustered in one area û Spring Gully. The results of this sampling program led to immediate identification and, ultimately, the successful delineation of the Spring Gully gold deposit near Wattle Flat.

Jan 1, 2004

By A Manzoori, M T. Shadloo

This paper describes a CFD modelling study which was carried out to investigate possible improvements in the design of an alumina precipitator tank at the Jajarm plant of Iran Alumina Company. In particular, the tank has an impeller located very close to the tank bottom, such that it quickly becomes covered with settled solids after a shut-down of the agitator, making it difficult to restart. A CFD model was firstly set up in which the existing design was evaluated in terms of flow pattern, off-bottom suspension and distribution of solids, and power consumption. Further simulations were then carried out to test alternative designs, leading to a recommended design, which maintains good mixing, with the same power consumption and without the use of a low-clearance impeller.

Jan 1, 2006

Located 350 km west of Sydney and 20 km outside Orange, NSW, lies the Ridgeway Gold Mine û NewcrestÆs flagship Underground Gold Mine. Key to success at Ridgeway has been the fast tracked development of the 3.8 km, 1 in 5.3 conveyor decline which houses the 850 t/hr conveying system feeding the dedicated Ridgeway Concentrator, built adjacent to the existing Cadia Hill Concentrator. Eroc was contracted to develop the steep conveyor decline, drawing on its personnel and experience from past metalliferous, tunnelling and coal mining projects to complete the ambitious schedule within 12 months. This paper deals with the complexities and experiences in safely delivering what is understood to be one of AustraliaÆs steepest declines of any substantial length in a metalliferous mine.

Jan 1, 2002

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By C D. Rose

A review and summary of the results of 120 coal sampling system bias tests is presented. This review supports new methodology using multivariate statistics currently being considered by ISO TC27 SC4. The current difficulties with ISO 13909-8 are explained and the logic behind the current new working draft is discussed in detail. Bias was detected in nearly 36 per cent of tests reviewed, suggesting that much improvement is needed in designing, maintaining and monitoring the performance of sampling systems in order to avoid sampling bias.CITATION:Rose, C D, 2012. Bias testing of mechanical sampling systems for coal - A review of test results and call for use of multivariate statistical analyses, in Proceedings Sampling 2012 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By R L. Chaney, M Mahoney

Mine and ore beneficiation wastes and smelter contaminated soils often cause phytotoxicity and threaten adverse environmental effects if not remediated. Science has clarified both the risks from soil metals and methods to alleviate those risks that can be applied at low cost. Phytoremediation is a family of plant and agronomy based technologies to deal with environmental aspects of sites requiring remediation. If valid risk assessment indicates that metals comprise risk, phytostabilisation may be used to alleviate that risk for most contaminated sites. In particular, Zn-Pb, Cu and Ni mine and smelter sites are readily remediated by making the soil calcareous and fertile, with added organic and metal sorbent amendments that include soil microbes to ‘revitalise’ the soil. In each case, the soil fertility and causes of phytotoxicity should be clarified by agricultural soil extractions, and the combination of amendments required to improve fertility and reverse phytotoxicity identified and found locally. In contrast with phytostabilisation, phytoextraction/phytomining uses rare metal hyperaccumulator plants and agronomic management to maximise annual phytoextraction of soil elements into plant shoots for harvest, ashing and use as a metal ore. Plants that accumulate more than two per cent Ni in shoots, and yield 10–20 t ha-1 dry biomass yield 200–400 kg Ni ha-1, which has value greater than all common agricultural crops. Considering the value of elements, existence of hyperaccumulator plants and demonstrated agronomic management for Ni phytomining, it is clear that mine sites and Ni mineralised subore-grade serpentine soils can be phytomined economically as an agricultural mining technology. A team developed agronomic methods and improved cultivars of Alyssum, which can be profitably grown on temperate zone Ni mineralised or contaminated soils. Plant species for tropical ultramafic soil materials have been identified. Phytoextraction is also strongly needed to remove Cd from rice soils to prevent human disease from soil Cd.CITATION:Chaney, R?L?and?Mahoney, M, 2014. Phytostabilisation and phytomining – principles and successes, in Proceedings Life-of-Mine 2014 , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By D J. Kilkenny

Work practices involved in shaft construction can be aligned with current industry standard operating practices. However, the working environment during conventional shaft construction introduces unique conditions which can not always be overcome by hard engineering controls. To provide an improved working environment, future shaft diameters will generally be greater than has historically been the case for the Australian hard rock mining industry. This paper aims to explore both what can be constructed from the contractors perspective, and how does an owner extract maximum business efficiency from an asset that in many ways is likely to be larger, more complex and more expensive than initially envisaged.Newcrest Mining Limited, or an associated company, has constructed two major shafts over the last seven years. In both cases, Byrnecut Mining, or an associated company, was the contractor engaged for the shaft sinking activity. The first is the 1127 m deep, 7.0 m diameter production and intake airway at the Telfer Gold Mine, the second is a 295 m deep, 5.5 m diameter split shaft at the Gosowong Gold Project in Indonesia that was primarily designed as both an intake and exhaust airway. Importantly both shafts are designed to provide emergency egress from the respective underground operations.From an Australian shaft sinking perspective, the construction of these two shafts resulted in the following learnings: •constructability is of equal importance to desired functionality;•allow six months of interactive design between the owner/engineer/contractor/regulator to get it right;•shaft sinking and equipping are intimately entwined, therefore engineering of both needs to be complete prior to any activity commencing; and•the mobilisation of both equipment and experienced personnel to a new shaft sink takes up to eight months.Shaft sinking is not extinct in the Australian hard rock mining industry. But, if you are considering constructing a shaft, approach it as a long life asset, front end planning to a high level of detail is required to unlock its full value. Think – plan – think and remember it’s going to take 12 months to get from the whiteboard to firing the first cut.

Mar 21, 2011

By J Canterford

Although we have access to a wide range of sophisticated process design and improvement tools in combination with a significant range of case studies, the mineral resource industry still manages to be plagued by the negative publicity surrounding operating plant failures because they were neither smart nor safe, together with proposed projects that fail at the first or second hurdle. The general public and the finance industry are generally totally uniformed about projects that ramp-up to name plate capacity on time and on budget and even more so when ahead of schedule and under budget. As the saying goes, good news does not cut the mustard.The following is a summary of the author’s sometimes jaundiced view about why metallurgical plants do not live up to their technical and commercial expectations. In no way should the summary be construed as a negative reflection on the skills of the metallurgical profession. Rather, it is to be taken as a positive acknowledgement of those skills and is intended to highlight some of the major considerations that need to be assessed as a potential project transforms into a sustainable technical and commercial reality.While a considerable portion of the summary is directed at developing hydrometallurgical flowsheets, the general principles are equally important to all aspects of extractive metallurgy.For convenience, the summary covers the following five basic discussion points – project, people, process, patents and politicians.

Aug 8, 2011

LKAB operates two underground mines in Kiruna and Malmberget, Sweden. Blast furnace pellet is the main product and makes up 70 per cent of total production. The orebodies are hosted by 1910 - 1860 Ma old volcanic rocks. The host rocks and the ores were affected by the Svecokarelian orogeny for 1890 - 1860 Ma ago. The deposit belongs to the Kiruna type apatite-rich iron ore. Magnetite is the main ore mineral but haematite is the dominant ore mineral in some orebodies in the western part of the deposit. Large-scale sublevel caving is the dominant mining method. Three main haulage levels are in operation at present. The ore boundaries and quality can be detected by geophysical logging resulting in reduced waste dilution and subsequent grade reduction. The susceptibility measurements have been used in the magnetite ore since 1991 and gamma-gamma measurements in the haematite ore since 1998. The mining scale has increased during the last 20 years but diamond drilling has remained at approximately 18 000 drilling metres per year. Uncertainties in the ore constructions can lead to unexpected cost increases, ore loss and dilution. The ore boundaries are evaluated with percussion drill holes using in-hole geophysics to achieve satisfactory geological knowledge. The probes are calibrated in all currently mined orebodies. The correlation between core sample assays and measured susceptibility and gamma-gamma values is strong. The cost to determine the ore boundary by percussion drilling with in-hole geophysics is two-thirds lower, and productivity is six times higher compared to diamond drilling. The measurements are made by geotechnicians and the interpretations by a geologist. The results are transferred to a database and presented three dimensionally as holes with iron grade intervals on mine maps. The interpreted holes are used by the geologist in various ways in the geological modelling. Layout planning uses the measurements as a tool to place the drifts at the correct distance from the ore contact especially in the longitudinal sublevel caving and the production hole planning to optimise the final length of the cross-cuts and drifts for best ore recovery.

Jan 1, 2006