Search Documents

By MattelmSki M

Outokumpu Harjavalta Metals Oy has been producing nickel since 1962, based on conventional flash smelting technology followed by electrowinning of nickel. In the 1980s, a research project was initiated to develop a converterless direct smelting process to produce matte for further refining in the then existing refinery. The process was tested on a pilot plant scale at Outokumpu's research centre in Pori and was found to be viable. The process was named the Direct Outokumpu Nickel Smelting Process or the DON Process. At the turn of the 1990s, Outokumpu studied various options to develop its nickel business and the Harjavalta operations. As a result of this work, the DON Process was further developed to produce two mattes: low iron matte in the flash furnace to be leached in the existing leaching circuit and high iron matte in the electric furnace to be leached in the new leaching circuit. In Harjavalta's case, it was essential and important that the process could use the existing flash furnace and electric furnace without converters.

Jan 1, 1996

By M Medina, J Alexander, R J. Longey

Capricorn Copper Pty Ltd (CCPL) are operating the Capricorn Copper Mine located at Gunpowder, Queensland. As current holder of the environmental authority for the site, CCPL have obligations to rehabilitate areas of the mine that are no longer operational and have the potential to cause/contribute to environmental harm. CCPL sought a voluntary Transitional Environmental Program (TEP) to provide an agreed program of works to cap and rehabilitate the former Mammoth Tailings Storage Facility. The voluntary TEP contained conditions that were required to be met, to reduce the potential for environmental harm from the facility. The former Mammoth Tailings Storage Facility commenced use in the early 1970’s, and is an unlined valley in-fill structure, contemporary in design compared with other such approved structures of the era. The decommissioned Mammoth Tailings Storage Facility, now known as the Old Tailings Storage Facility (Old TSF), has been a legacy source of contamination due to the existing capping not meeting modern cover criterion, and allowing oxidisation and infiltration to the underlying acid forming tailings resulting in Acid and Metalliferous Drainage (AMD) from the facility. A cover design for the Old TSF, and other mine waste storages onsite that required clay capping, had been proposed by previous operators. Under the TEP cover design phase, it was identified that a key constraint was the lack of significant quantities of low permeability clay onsite. The lack of available clay prompted the consideration of alternate lining materials for the Old TSF, with a Bituminous Geomembrane Liner (BGM) being adopted as the preferred alternative. The BGM compared favourably with clay-based materials on seepage analysis, and led to other benefits by eliminating the need for borrowing clay off site, reducing the site’s environmental footprint, and reducing construction time. The BGM cover system on the Old TSF is being monitored with the intent to use this as a case study to confirm expected performance, enabling the cover design to potentially be adopted on the remainder of the site’s mine waste storages that require capping.

Jul 1, 2021

By B Howard, M Jones, D Pershke

"Current closure objectives and criteria are often difficult to achieve and are not delivering value for money outcomes at closure. Current mine closure processes tend to focus on rehabilitation and revegetation of landform structures to as close to premining condition as possible, rather than focusing on the functions of those structures and values they provided. Because mining has highly disturbed the environment, premining conditions and vegetation are often not achievable and objectives and criteria aimed at achieving close to these conditions have been shown to be very costly.The authors have developed a broader approach to developing mine closure plans that is based on environmental risk and gaining post-closure social, environmental and economic value. We think the focus should shift from trying to return the original landscape to returning functions and values provided on- and off-site. If it is not possible to return values on-site in a cost-effective manner, investment should be provided to deliver equivalent values elsewhere.This process can provide better stakeholder acceptance, deliver better environmental outcomes on the tenement and within the catchment and significantly reduce costs, whist fulfilling closure obligations.This framework should enable closure teams to: focus on the functions and services that are important to achieve as outcomes post-closure, rather than a focus on revegetation and replacing the premining biophysical structure engage meaningfully with stakeholders regarding closure outcomes and link outcomes to stakeholder values conduct transparent option evaluations that enable stakeholders to clearly understand the costs and benefits associated with each option and to participate in dialogue on option selection.We present examples of how the framework could be applied to identify alternate closure options that achieve equivalent value outcomes while reducing the costs of closing the mines.CITATION:Howard, B, Pershke, D and Jones, M, 2014. Achieving better mine closure outcomes for less money, in Proceedings Life-of-Mine 2014, pp 615–620 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 16, 2014

By F K. Altuntov

The study presented in this paper is based on the Kiirunavaara underground mine located in the northern part of Sweden. The deposit is mined using the sublevel caving (SLC) mining method. This paper briefly reviews the alternative SLC layouts, as well as presents challenges for the application. In Kiirunavaara currently, the traditional SLC design is employed, however, continuous improvement of material transportation systems used in mines generates a need for investigation of the current and future production area layouts in sublevel caving mines. When identifying the potential benefits of the alternative production area layouts, the production targets and effects must be further investigated to understand the benefits and potential effects. In this study, several different layouts have been investigated and evaluated. The designs include different development configurations and orepass infrastructure moved further away from the orebody and still require further investigation.

Mar 29, 2023

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation: W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By G Byrne

Long-term water management is typically ignored in mine closure planning. A review of 73 mine closure plans dating from 2007 to 2013 shows that, on average, relinquishment is proposed to be achieved in 11 years. A separate review of 57 mines in actual closure shows that only five have so far achieved relinquishment with an average closure period of 14 years after production cessation. The remaining 91 per cent of sites in closure have an average closure duration to date of 21 years - and still going.A common issue among those sites in closure is water management, with a further common issue being acid and metaliferous drainage (AMD). Of the closure plans that were reviewed only one site had allowance for long-term (>50 years) of water treatment. Of the sites in actual closure 25 per cent have reported that they expect such long-term water treatment, with many acknowledging that in perpetuity treatment is probable.Clearly there is a gap between what is being allowed in closure plans and the reality of closure. There are a number of factors leading to the optimism of the closure plans, including unrealistic assumptions, pressures to reduce closure cost provisions and the technical complexity of many AMD issues.Long-term water management is a reality that needs to be acknowledged and addressed. If addressed early in the mine life cycle the impacts for mining companies can be reduced.CITATION:Byrne, G, 2013. Long-term water management - the forgotten legacy of mine closure, in Proceedings Water in Mining 2013 , pp 163-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By P K. Wong, D A. F Oliveira, F M. Azad

In situations where foundation piles are located in proximity to existing or future tunnels, it is typical for the tunnel owner to require that sleeving of the piles be carried out to at least the invert of the tunnels to minimise any load transfer to the tunnel lining. In competent rock, this practice may be sometimes unnecessary, thus uneconomical. This paper presents an assessment of the effect of pile loading from one of the multi-storey buildings at Barangaroo South in Sydney on the adjacent future Sydney Metro tunnels. It was originally required by Transport for NSW (TfNSW) that the piles be sleeved below the tunnel invert level; however, the building developer wanted to reduce the pile sleeving depth to achieve a more economical solution due to the large number of load transfer piles being required for the project. To assess this feasibility, a full 3D commercial numerical code, FLAC3D, was used to carry out this complex soil-structure interaction analyses. Based on these assessments, it was demonstrated successfully to the TfNSW that the pile sleeving may be terminated at 2 m above the tunnel invert level. For this arrangement, the investigations found that the loading on the piles should have negligible adverse impact on the tunnel lining design. As a result of such an assessment, the proposed pile sleeving level was approved by TfNSW, thus offering an economical foundation solution for the project.CITATION:Azad, F M, Oliveira, D A F and Wong, P K, 2014. The impact of pile loading on adjacent metro tunnels – Barangaroo South, Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 355–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By T Ireland, S Eratne, W Newns, P Spies

The approach to risk management during the procurement of major projects often has a significant outcome on the ultimate delivery of a project. The NZ$1.4 B Waterview Connection project is the largest and most complex project yet undertaken by the New Zealand Transport Agency (NZTA) and the procurement process for an alliance contract was refined to provide compliance with the International Tunnel Insurance Group (ITIG) Code of Practice for Risk Management of Tunnel Works (TCoP). The principle of shared risk within an alliance incentivises a common understanding of project risks prior to finalising the alliance agreement and therefore enables superior risk management through design, construction and beyond. Risk management practices need to be instigated well in advance of commercial phases, so that commercial competition does not lead to a significant elevation of project risk. In particular the practice of gaining commercial advantage by taking on a potentially unmanageable level of risk is one of the outcomes to be avoided by the TCoP.During the procurement phase the NZTA placed high value on design and construction mitigation measures proposed in order to address ground risks, as is appropriate for a major tunnel project. In order to achieve alignment on the level of geotechnical risks an Alliance Geotechnical Baseline Report (AGBR) process was developed.This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. Refinements to the procurement process to ensure compliance with the TCoP prepared by the International Tunnel Insurance Group (ITIG) are described along with the AGBR process applied as part of a suite of measures to achieve a successful procurement outcome.CITATION:Ireland, T, Spies, P, Eratne, S and Newns, W, 2014. Risk management and use of a geotechnical baseline report for a competitive alliance procurement?process, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 553–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Berry

Consider these four questions:What is the definition of life-of-mine?When should life-of-mine planning seriously commence?When can life-of-mine planning seriously commence?What is the key input to effective life-of-mine planning?Whilst there is likely to be general consensus on the answers to the first three questions, the answer to the fourth question is open to debate. This author argues that understanding and managing risks and opportunities associated with geological uncertainty is the key input to effective life-of-mine planning, at all stages in the life cycle of a mining project.CITATION:Berry, M, ?2014. Effective life-of-mine planning by understanding and managing risks and opportunities associated with geological uncertainty, in Proceedings Life-of-Mine 2014 , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Norbert, P Mok

The mainline running tunnels for Legacy Way comprise of two-lane tunnel boring machines (TBM) driven tunnels. The length of the TBM tunnel section is approximately 4.2 km. The TBMs employed are double shield TBMs. Typical support to the segment ring while advancing a double shield TBM comprises of filling the excavated annulus between the ground and the segmental lining by injecting pea gravel, followed with primary grouting to fill between the pea gravel some distance behind the excavated face. The methodology adopted for the Legacy Way project, however, did not follow this typical approach, instead, two component grouting of the annulus was carried out.Where the annulus is typically filled with pea gravel, support is provided to the segment ring very close to the end of the tail shield, whereas in the case of two component grout this is not practical as the risk of grouting in the tail shield is high. The staging of the two component grout injection, the grout early age strength properties become key issues in ensuring that the segment ring leaving the TBM tail shield is stable and can support the necessary external loads.Two-component grout is a grout with two components, cementitious grout (component A) and accelerator (component B), commonly adopted for earth pressure balance (EPB) TBM. The grout reaches its thixotropic state in a matter of seconds providing initial support for the segment rings. Manual injection of two component grout to fill the bore annulus was carried out in stages leaving a portion of the segment rings unsupported. Ring stability during TBM advance was provided by a combination of ram thrust and the segment circumferential joint shear connectors.This paper outlines the design considerations such as rock load derivation by probabilistic analysis carried out utilising the software JBlock, 3D finite element analyses using the software Strand7 for ring stability and the testing and back analysis of the shear connector load bearing behaviour. In particular, the actual available capacity of the shear connectors against their published capacity by supplier was discussed.CITATION:Mok, P and Norbert, M, 2014. Tunnel boring machine excavation stability – double shield tunnel boring machine advance with partially grouted annulus, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By F Sandrone, J-P Dudt, J Zhao, E Paltrinieri

Tunnel boring machines (TBMs) excavation is nowadays more and more considered a valuable alternative to conventional tunnelling. As a matter of fact, thanks to its advantages such as greater rate of advance and safer working conditions, the application of TBMs has increased significantly in recent years. Despite the possible excellent performance of TBMs in favourable ground conditions, the advance rates could be significantly slowed down or even obstructed in limiting geological situations. This obviously traduces in potentially longer tunnel construction times and higher costs and, therefore, in a preference for conventional method. One of the major geological hazards encountered during tunnel construction, is related to the presence of fault zones or heavily jointed and fractured rocks. The most common geotechnical problems resulting from tunnelling in these difficult conditions include the instability of the excavation face, instabilities of side-walls producing large overbreaks on the tunnel profile, excessive deformations in case of squeezing grounds, frequently changing stresses in terms of magnitude and direction, high water inflows, etc. The decisions aids for tunnelling (DAT) is a model and a computer code that can be used to evaluate the influence of the uncertainties related to both the geological/geotechnical conditions and the construction process on final tunnel construction time and costs. In this framework, the DAT is used for assessing the effects that challenging ground conditions may have on tunnelling operations in terms of costs and delays. This is done by simulating the tunnel construction considering several geological profiles. The aim of the study is comparing different excavation methods (ie drill and blast versus TBM) in changing ground conditions along the tunnel alignment ranging from good rock, to very poor and fractured formations. The results show the impact, in terms of changing construction time and cost, of the excavation method versus the ground conditions.CITATION:Paltrinieri, E, Dudt, J-P, Sandrone, F and Zhao, J, 2014. Comparison of excavation methods in different ground conditions with the decision aids for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 573–580 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Mee, R L. Gwyther

Accurate measurement of rock mass response during the mining of massive underground orebodies is essential, as mines become larger and deeper. These measurements enable: provision of quantitative data for optimal pit slope design and engineering; monitoring of the stability of deep pit slopes, the long-term integrity of shafts and large-scale underground infrastructure, and long-term measurements of deformation or rock mass creep following the mining process for environmental management. Strainmeters traditionally used for deformation measurement have neither the long-term stability nor the high sensitivity to perform measurements in these applications. This paper describes a new precision borehole strain monitoring system (GTS) currently deployed by CSIRO Exploration and Mining, which has the potential to solve these new issues in rock mass deformation monitoring. This technology was originally developed for use in hard rock mines (Gladwin, 1977) and refined considerably for earthquake research (Gladwin et al, 1994; Gwyther et al, 1992). A case study of the use of the GTS in monitoring longwall coal mining over the period 1993 - 1998 is presented.

Jan 1, 2000

By J Bohm, B Csoke, I Tarjan

In process technology, especially in coal preparation, it is often necessary to have a continuous knowledge of the average density of granular material in order to achieve both quality control and process control. The paper presents a new method and means supported by laboratory measurements for the rapid, practically continuous, determination of the average density of continuously supplied granular material through frequent sampling.

Jan 1, 1993

The Mt. Sisa Orebody on Misima Island, P.N.G., consists of gold-silver mineralization associated with massive carbonate and amor- phous iron-manganese oxides in fractures and breccia matrix. The orebody forms the north- ern extension of the Umuna deposit. The mineralization lies within the three kilometre strike length of a northwest trending, 300 metre wide, high angle fault zone. The fault zone structure is deeply oxidi- sed, with the manganiferous oxide material resulting from oxidation of carbonate. The wallrocks are metamorphosed basement psammopelites and basic volcanic rocks, exten- sively intruded by microgranodiorite. These are dominantly epidotized and sericitized. The precious metals are associated with anomalous Cu, Zn, Pb, Mn, As, Ba, Ga, Sb, and. Mo. Many of the features of the Mt.Sisa mineralization are characteristic of volcanic- hosted epithermal deposits of western North' America. Lithologic and textural gradation is ob- served between the carbonate hydrothermal breccia-fill at Mt. Sisa, and the quartz domi- nated dilational fracture-fill mineralization which forms most of the Umuna deposit to the south. This gradational relationship is ana- logous to that within the Amethyst-OH vein system at Creede, Colorado, where it is shown to be indicative of deposition from laterally migrating fluids.

Jan 1, 1987

By J Zhao, Q B. Zhang

The shock behaviour of a material represents its response to very high strain rate loading at pressures associated with those generated by explosive and blasting loadings. Three sets of shock wave experiments have been conducted to determine shock Hugoniot behaviour, spall tensile strength and shear strength using a plate impact facility. Embedded manganin stress gauges (ie longitudinal and lateral gauges) and high-speed velocimetry using heterodyne techniques were used for the measurements of stresses, shock velocity and free surface velocity. The gabbro exhibited classic linear Hugoniot equations of state in the US-up (ie shock velocity-particle velocity) plane; while for marble a polymer-like non-linear response was observed. The detailed experimental procedures used to make these measurements are to a great extent standard methods when determining mechanical properties and deformation fields at high strain rate.CITATION:Zhang, Q B and Zhao, J, 2015. The response of rock materials to one-dimensional shock loading, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 665–672 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Agdaca

Leightons is the sole contractor at the Wahana Coal Mine Project (part of the Bayan Group), a multi-seam thermal deposit consisting of 13 coal seams with thicknesses ranging from 20 cm to 500 cm. The average dip of the deposit is 18 - 20°. However the deposit is heavily faulted in certain domains with anticlinal and synclinal structures present causing seams to dip up to 90°. Average thickness of coal inter-burdens range from less than 2 to 12 m. The minimum coal thickness being mined is 20 cm. Coal production is direct mine mouth feed and there is no coal processing plant currently used.Conventional blasting between the highly variable coal horizons in the early phases of the mine life was suboptimal from a production perspective. Drilling short holes with a reduced drill pattern, and on occasions with sloping benches, resulted in low drilling and explosives loading efficiency.A high frequency of small size blasts fired up to two times daily was required with each blast consisting of four up to five small blast areas. Each blast averaged approximately 36 000 bcm thus causing a low utilisation rate of the mining fleet from frequent blast delays and the inability to deploy larger Liebherr 9350 excavators on bench. It was identified that increasing the production targets required a more efficient drilling and blasting process. Furthermore, due to the highly variable nature of the deposit, the existing coal model was determined to not be able to accurately predict the coal seam location prior to blasthole drilling.In August 2009, Leighton Contractors Indonesia and Orica Mining Services with the full support of the Wahana team, initiated through seam blasting trials using electronic blasting systems. Further trials were conducted in November 2009. Trial evaluations indicated that the benefits from decreased lost time events due to blasting, an increased vertical advance rate per blast, and increased overall blast size could be attained while not damaging or diluting coal.Full-scale?through seam blasting has been ongoing since February 2010 for the upper eight coal seams to extract coal seam thicknesses ranging from 20 - 100 cm. This paper will discuss the parameters of the through seam blasting process in Wahana and the resulting benefits to the overall mine production.

Nov 8, 2011

By R Osterman

As mining companies have to go deeper in search of ore and coal, the importance of protecting the highwall increases. Wall fatigue also increases with importance of the long life expectancy of a highwall, in particular the impact of fatigue influenced by resonance. Resonance is the tendency of a material to oscillate with greater amplitude at certain frequencies when exposed to a periodic force. Until recently, only dominant frequencies, either natural or induced, were all that could be measured through the fast Fourier transform of the blast-induced wave form.This paper presents a novel method to accurately predict the resonant frequency of a highwall. In fact, the method can predict the natural frequencies between any two monitoring points placed in line with the source of impact, and as such it can be used to determine the resonant frequencies of any physical object. The method not only predicts the resonant frequencies of the material; it predicts the structural response of the total frequency spectrum. This method helps describe the response of a mechanical structure to excitation. It describes the structure’s efficiency in the use of energy, that is, whether energy is dampened or consumed in resonance.The initial predictions have been so accurate that it made it possible to determine the fundamental frequency and the first six harmonics of a highwall in a northern Queensland coalmine. With the use of electronic detonators, the blast can be timed with a repeating delay to create an induced artificial frequency that has been determined to retain the least amount of energy.CITATION:Osterman, R, 2015. Transfer function – new method to accurately predict resonant frequencies of a highwall, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 233–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Dal-Corobbo

Traditional acid and metalliferous drainage (AMD) wastewater treatment focuses on the iron co-precipitation/adsorption process as this is a very effective method of reducing heavy metals, including copper, lead, zinc, arsenic, etc, to parts per billion (ppb) levels in AMD wastewater streams. One of the drawbacks to this method however is the large volume of sludge produced and subsequent disposal costs for the mine site concerned.A proprietary metals treatment system called high density sludge (denoted HDS) which significantly reduces the quantity of waste generated is described in this paper. This process generates a dewatered sludge that contains in the order of 50 to 55 per cent solids. This sludge is denser than conventionally dewatered sludge, which typically contains only 20 to 30 per cent solids. This advanced process has a wide range of applications and can be easily retrofitted into existing AMD treatment systems. It has been successfully installed at several mine sites to treat AMD wastewaters. This paper discusses the high density sludge process, its benefits and provides data and operating results from pilot test installations.CITATION:Dal-Corobbo, A, 2013. High-density sludge process for treating metal bearing acid and metalliferous drainage wastewaters, in Proceedings Water in Mining 2013 , pp 217-220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By W R. Adamson

Cerro Vanguardia SA (CVSA), property of AngloGold Ashanti, mines gold and silver from a system of vetiforme orebodies located in the south of the Argentine Patagonia, in the Province of Santa Cruz.Surface mining techniques are applied to develop a series of narrow pits with an average waste to ore ratio of 26:1. This quite unique constraint brings into focus the need to maximise inter-ramp and final wall angles, leading to a strong need to optimise wall control drilling and blasting in order to reduce back-break damage to an absolute minimum.The paper describes a program of applied investigation and design modification implemented during?2008?and?2009 in?two?separate pits of Cerro Vanguardia. Three distinct yet complementary damage mechanisms were identified and observed during the field components of the work; vibration induced strain fracturing, surface cratering around blasthole collars and quasi-static loading and unloading of the surrounding rock mass as a consequence of poorly controlled confinement.With these mechanisms identified, a measurement, modelling and modification campaign was conducted in order to reduce the incidence of each source of damage. Interactive design analysis and modelling, near-field vibration measurement, video capture and the application of electronic initiation technology were supported by seed wave modelling and topographic evaluation of the achieved results.Results point to the usefulness of simulation techniques for determining optimum delay timing to reduce vibration impact, while the visualisation of explosive energy distribution produced by drilling and explosive loading decisions assists in reducing the probability of over-confinement.This paper presents relevant aspects of the two fieldwork campaigns:1) describing the application of the techniques, and2) summarising the results obtained.

Nov 8, 2011