Search Documents

By J A Evans

A well-maintained and low cost mining operation today requires the use of condition monitoring techniques. At ERA - Ranger Mine oil analysis, vibration monitoring, infra-red themtography, and performance analysis have been successfully applied over the last four years to lower operating and maintenance costs. All condition monitoring is scheduled through a comprehensive in-house developed maintenance management system known as the Engineering Information System (EIS). (EIS) is used extensively at Ranger to ensure consistent frequency and recording .of all condition monitoring data. This paper provides an insight into the benefits of condition monitoring and explores the future direction for condition monitoring techniques at Ranger.

Jan 1, 1994

By S N CARRAS

Ore reserve estimation is a procedure involving data collection, data storage and judgement and assumptions about geology mining and metallurgy. Calculations are based on these assumptions and an economic analysis on projected cash flows is carried out. Ore reserve estimation must therefore be subjective and will always depend on the extent to which the assumptions used in arriving at the estimate are correct. This paper is an attempt to summarise the many aspects that can contribute to ore reserve problems and to offer some suggestions on how to minimise these problems. For further details on specific concepts readers are referred to the detailed descriptions in the referenced papers.

Jan 1, 1992

By D J. Brake

The underground metalliferous mining industry continues to change under the influence of many factors including, to name a few, new mining techniques and equipment, new approaches to risk management, more stringent safety and health standards, new employment practices and orebodies become deeper and often lower grade. In addition, the same technological revolution and plummeting cost of technology that has brought the GPS, smart phones and digital cameras to the general population is also working its way through the mining industry impacting on communications, automation and process control as well as introducing major efficiency and productivity dividends. However, not all factors are positive including, in particular, the issues of carbon costs and electrical power. This paper explores some of the trends affecting ventilation in hard rock mines, some of the existing and likely future challenges and some of the potential future solutions to these issues.CITATION:Brake, D J, 2013. Ventilation challenges facing the metalliferous sector, in Proceedings The Australian Mine Ventilation Conference , pp 3-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J Cook

In this paper we present a case study of the challenges and opportunities associated with the development of cultural heritage management strategies at the Lihir gold mine in Papua New Guinea. We discuss the contextual drivers and constraints, and outline the ways in which Lihir Gold Limited is aiming to set new industry bench marks for the region through the development of values-based best practice cultural heritage management programs. This approach is largely based upon a compliance partnership with a local stakeholder group. We argue that such partnerships are a prudent means of mitigating company risk, while constituting a far more necessary tool for local people in the reconceptualisation and negotiation of the experiences of significant social change and modernisation experienced in the context of recent resource development.

Jan 1, 2009

By A Galli

Traditionally pit optimisation and scheduling is carried out assuming that the resources, the commodity prices and production costs are all known. Once the pit contour and the mining schedule have been determined, geostatistical simulations can be used to assess the impact of the uncertainty in the resources on the pit design and the schedule, and likewise stochastic simulations can be used to test its robustness to fluctuations in costs and prices. But it would be more interesting to have a dynamic procedure for optimising the pit as the resources become better known and as economic factors such as commodity prices and costs evolve over time. This paper presents a novel approach for doing this. Rather than working with millions of small selective mining units, it was decided to work with large blocks, called macro-blocks. Mining sequences are defined as the quantities to be extracted from each macro-block in each time period. Feasible mining sequences are mining sequences that respect the accessibility constraints, and also the geometric constraints on the amounts that can be extracted from any one block over time, or from all the active blocks at a given time. Having defined feasible mining sequences, their mathematical properties were studied. It was found that natural breakpoints occur in the sequences when one set of blocks have been completely mined out, thereby opening up access to others. It was discovered that families of sequences exist, and that they are convex and closed under certain types of row permutation operations. Convexity is an advantage when optimising. The closure property opens up the possibility of mixing and matching subsequences of rows in the sequences. Another interesting property is that the sequences form branching families, rather like the binomial and trinomial trees used to model prices in finance and in real options.It is easy to generate large numbers of feasible mining sequences randomly. A two-step procedure is used to find the best one (or the best few) using three economic criteria: expected NPV,the probability of a negative NPV, and the percentage of years when the cash flow is negative. The procedure was tested on a synthetic gold mine based on the characteristics of the Essakane mine in Burkina Faso. The results were encouraging.

Sep 26, 2011

By M Manefield, G Bournival, S Ata

Asteroids contain an abundance of valuable resources such as: nickel, cobalt, gold, platinum and rhodium. Whilst the consumption of mineral resources on Earth continues to deplete, meteoroids have the potential to become a significant source of minerals. Even though the minerals content of asteroids may be relatively high, the valuable minerals are more likely to be only a small portion of the total ore present in the main body. The ores must, therefore, be processed to extract the metals of interest from the waste. Existing terrestrial technologies rely on manipulating the physical and chemical properties of minerals. The application of these techniques to asteroids processing, however, is not straightforward due to the presence of different conditions such as zero gravity and lack of water in space. This paper discusses potential separation and extraction techniques that can be used for processing of asteroids.CITATION:Ata, S, Bournival, G and Manefield, M, 2015. Resource recovery in space, in Proceedings Third International Future Mining Conference, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Determining the controls of high-grade mineralisation at Vera Nancy requires careful data collection and assessment on a global and specific deposit basis. The techniques developed over 60 years ago to analyse structure, grade and width data are just as applicable today and can be enhanced using modern geological modelling software. High ore grades at Vera Nancy are controlled by both the primary geometry of the mineralised structure and the intersections of the main mineralised veins with subordinate splay veins. The main mineralised structure dilated as a consequence of extensional tectonics while the splays acted as conduits bringing oxidising surficial fluids into mixing zones precipitating high gold grades. Near-mine exploration is focussed on identifying zones of vein flexure and splay interaction to locate the relatively small high-grade shoots. Data modelling in a 3D environment is an essential process for understanding the geometry of the system being explored.

Jan 1, 2000

By S Hapugoda, A Edenton, L Lu

The blast furnace cohesive zone has a profound impact on hot metal productivity and quality, fuel consumption, operational stability and the lining life of the blast furnace. The high temperature properties of ferrous burden materials determine the configuration and location of the cohesive zone and have therefore attracted particular attention. While numerous standard testing methods are in use to assess the quality of ferrous burden materials for the blast furnace, these simple tests are generally conducted under fixed conditions, which often represent the extreme situations encountered by the burden materials in the blast furnace. Furthermore, none of these simple tests provides information on the high temperature properties of the burden materials, such as their softening and melting properties. CSIRO is equipped with a fully computerised testing facility to characterise the high temperature properties of ferrous burden materials under realistic conditions similar to those encountered in the blast furnace. This paper will first review the CSIRO softening and melting test method and then discuss the softening and melting properties of a variety of blast furnace burden materials, including sinter, pellets and lump ore, and their implications for blast furnace operation.

Nov 8, 2021

By G J. Showers, P Botman, A G. Hunt

Iron Road Limited (Iron Road) is currently evaluating the feasibility of producing 21.5 Mt/a of high-grade (>66 per cent Fe) magnetite concentrate from a 3.7 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate can be produced via a conventional grind and low-intensity magnetic separation flow sheet. Due to the comparatively coarse magnetite liberation size (106 µm), consideration was given to enhancing both the grind economics and coarser product sizing via gravity separation.This paper outlines the test work, flow sheet design and engineering design of a gravity beneficiation circuit (GBC) conducted by Mineral Technologies for Iron Road. The resulting circuit optimisation necessitated mass balance simulation by Iron Road’s SysCAD model to quantify the resulting changes in mill recirculation load. This included the determination of project-critical grinding power and energy requirements with and without the GBC installed into the primary ball mill classification circuit. The outcome of this work was the design of a GBC, including spirals and up-current classification, which led to a substantial reduction (33 per cent) in ball mill recirculating load and power requirements, together with a favourable coarsening of final product size due to the relatively coarser gravity concentrate. This has led to a significant reduction in project design capital and operating costs. A further benefit of this approach is increased recovery of (paramagnetic) hematite and lesser titano-hematite via gravity separation compared to an all-magnetic separation approach.CITATION:Hunt, A G, Showers, G J and Botman, P, 2015. Test work and design of a gravity circuit for Iron Road’s Central Eyre Iron Project, in Proceedings Iron Ore 2015, pp 139–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

It is proposed to consider a new access, mining and hoisting system for underground deposits, as an alternative to the commonly used decline or vertical shaft access. The proposed system offers fundamental improvements in gathering of exploration data, reduction of capital expenditure and significant savings in mine operating costs. The cost reductions are achieved through:superior orebody definition by Supersucker winzing on ore prior to the commencement of capital development; considerable reduction of capital development in waste; full capitalisation on all benefits of a raisebored excavation; introduction of rubber tyred skip and rubber tyred Mine Rapid Response Vehicle; introduction of simplified ore handling system and reduction of underground mobile diesel fleet; and introduction of minimum maintenance shaft concept. The system is applicable to deposits ranging from shallow, low dip angle, narrow vein, high-grade to bigger, massive type vertical mineralisations accessed from the surface, preferably from the bottom of an open pit; it is also suitable as a down dip extension of an existing underground mine. The system is highly conducive to mine automation and emerging trend aimed to increase the ratio of mined metal/mineral to mined waste. It offers substantial reduction in diesel exhaust gas emissions to the mine atmosphere.

Jan 1, 2000

It is no longer adequate when starting a new mine to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency which requires systematic involvement of people in continual improvement of production and commercial processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. The presentation will show the practical and successful use of these principles. This paper will introduce the case study and provide background material on True TQM.

Jan 1, 1995

By R G. Moreby, S Bluhm, FávonáGlehn, C Pascoe

Resolution Copper Mine in Arizona, USA, is planned to be a 2000 m deep panel cave mine with virgin rock temperatures exceeding 80¦C in rock with high crystalline silica content, resulting in a very challenging ventilation and cooling system design. This is one of the largest copper orebodies ever found and, with a planned rock production rate of 120 kton/day. The project is currently in its prefeasibility phase and the paper discusses features of the ventilation and cooling system design which includes multiple ventilation shafts with total primary ventilation flow of about 3000 m3/s and both surface and underground refrigeration plants producing more than 140 MW refrigeration capacity. The cooling system features large surface bulk air coolers chilling all downcast air supplemented by an underground secondary air cooler system and a chilled service water system. This will be a very challenging mine to ventilate and cool but this work has demonstrated that it will be technically achievable with the application of existing technology.CITATION:Bluhm, S, Moreby, R G, von Glehn, F and Pascoe, C, 2013. Life-of-mine ventilation and refrigeration planning for Resolution Copper Mine, in Proceedings The Australian Mine Ventilation Conference , pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By J Bolen, I Cameron, M Huerta, M Okrutny, K O’Leary

As greater amounts of fine iron ore concentrates enter the marketplace, new investments in iron ore pelletising capacity are inevitable to deliver these concentrates to steel industry consumers. When investors assess the two well-proven pelletising technologies, the straight grate and grate-kiln, the most appropriate choice may not be immediately evident. Certain technical, market and site-specific factors will favour one technology over the other; investors need to be aware and understand these factors in order to make the best investment decision. Hatch has compared the merits of both technologies regarding plant configuration; type of iron ore processed; energy consumption and flexibility to use a variety of fuels; ability to produce the required pellet quality; required plant capacity and scale; operating and capital costs and environmental performance. A technology assessment checklist that investors should consider when making a new pellet plant investment decision is presented.CITATION:Huerta, M, Bolen, J, Okrutny, M, Cameron, I and O’Leary, K, 2015. Guidelines for selecting pellet plant technology, in Proceedings Iron Ore 2015, pp 45–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Lechner, T Baumgartl, S Arnold, P Audet

When revegetation is a part of a rehabilitation strategy at mine sites in arid and semi-arid environments, its success can be strongly affected by the availability of water prior or during the time of seed dormancy, germination and early growth of seedlings. The semi-arid and arid environments of northern Australia are characterised by highly variable and erratic rainfall and hence the actual weather conditions at and around the time of germination and seedling emergence play a critical role in determining the success of plant establishment and the type of plant community that may develop.Using available climate data, an analysis has been undertaken and a set of indices has been developed which describe the suitability of the climatic conditions for rehabilitation. In total, eight sites from Queensland and one site from New South Wales, Australia have been analysed. It could be determined that regular rainfall and relatively short periods of water-deficit are key characteristics of climate suitability. A comparison of the locations studied allowed the separation into suitable and susceptible locations in terms of the availability of water, amount of rain and duration of drought between rain events.In our experience, specific estimates of climate suitability are rarely incorporated into the design of mined land rehabilitation programs. We consider that the regional intensity, seasonality and extremity of climate represent an overarching component of landscape complexity, which in turn will influence the development of post-disturbance ecosystems in these regions. This paper presents the outcome of climate analyses paired with the development of suitability indices. A conceptual framework is presented explaining the suitability matrix and its incorporation as a prognosis tool to achieve greater certainty for success in rehabilitation development.CITATION:Baumgartl, T, Arnold, S, Audet, P and Lechner, A, 2014. Development of climate-based suitability indices for the improvement of success in rehabilitation, in Proceedings Life-of-Mine 2014 , pp 483–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By MattelmSki M

Outokumpu Harjavalta Metals Oy has been producing nickel since 1962, based on conventional flash smelting technology followed by electrowinning of nickel. In the 1980s, a research project was initiated to develop a converterless direct smelting process to produce matte for further refining in the then existing refinery. The process was tested on a pilot plant scale at Outokumpu's research centre in Pori and was found to be viable. The process was named the Direct Outokumpu Nickel Smelting Process or the DON Process. At the turn of the 1990s, Outokumpu studied various options to develop its nickel business and the Harjavalta operations. As a result of this work, the DON Process was further developed to produce two mattes: low iron matte in the flash furnace to be leached in the existing leaching circuit and high iron matte in the electric furnace to be leached in the new leaching circuit. In Harjavalta's case, it was essential and important that the process could use the existing flash furnace and electric furnace without converters.

Jan 1, 1996

The products of Lower Miocene calc- alkaline activity on the east coast of Northland, New Zealand are described and contrasted with coeval rocks of the northern North Island. These rocks, the Eastern Volcanic Belt (EVB), occur in four main centres aligned north-west to south east as either plutonic/hyabyssal bodies or as agglomeratic piles and dyke intrusions. Significantly the plutonic members always occur to the north-west of the volcanic members, probably indicative of differential uplift along faults (upthrown to the north) aligned perpendicular to the EVB. A full basalt-rhyolite (diorite-granodiorite/ adamellite) spectrum is represented, with a temporal progression towards the silica-rich endmembers indicated by cross-cutting field relationships. Modal mineralogy parallels this trend, consisting of two-pyroxene, hornblende, biotite, quartz/alkali feldspar modal assemblages, and with rare occurrences of olivine and garnet-bearing volcanic phases. Chemically the EVB is medium-K, calc-alkaline (with respect to AFM and total-Fe/MgO vs. Si02 indices) and quartz and hypersthene normative. The thirty two available K-Prisotope dates indicate that activity was largely confined to the Lower Miocene (24Ma-16Ma), with an apparent younging towards the south east. Initial B7Sr/e Sr ratios (0.70335- 0.70679) are indicative of a continental- arc-type setting, however it is unlikely that a straightforward tectonic reconstruction for this part, of the Pacific Margin is possible. Evidence from xenoliths, both petrologic and isotope, within EVB magmas and from regional geologic studies suggests that hypotheses pertaining to a volcanic arc sited over a subduction zone may hold little relevance in this case. The review concludes that the EVB developed from the partial melting of a geochemically evolved lower crust as indicated by xenolith evidence. This occurred in response to thickening initiated by a short-lived obductive event in the uppermost Oligocene, and controlled spatially by pre-existing basement structure. Intra-suite chemical and mineralogic variation reflects not only crustal variability, but localized differences in physico-chemical conditions best illustrated by the rare occurrences of olivine and garnet.

Jan 1, 1987

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014