Search Documents

By A V. Ozsever

The selectivity in flotation columns involving the separation of particles of varying degrees of floatability is based on differential flotation rates in the collection zone, reflux action between the froth and collection zones, and differential detachment rates in the froth zone. Using well known theoretical models describing the separation process and experimental data, froth zone and overall flotation recovery values were quantified for particles in an anthracite coal that have a wide range of floatability potential. For highly floatable particles, froth recovery had a very minimal impact on overall recovery while the recovery of weakly floatable material was decreased substantially by reductions in froth recovery values. In addition, under carrying-capacity limiting conditions, selectivity was enhanced by the preferential detachment of the weakly floatable material. Based on this concept, highly floatable material was added directly into the froth zone when treating the anthracite coal. The enriched froth phase reduced the product ash content of the anthracite product by five absolute percentage points while maintaining a constant recovery value.

Jan 1, 2005

By J Miedecke

A metalliferous mine has operated at Storys Creek from the 1890s to 1979. Storys Creek drains from a pristine catchment and National Park and remains as the most degraded stream from historic mining in north-eastern Tasmania. It has been the subject of public concern since the closure, particularly at times of high rainfall such as existed in 1985 and 1986. The mine is located on the banks of the creek, which flows into a major river, the South Esk River, which is one of TasmaniaÆs largest rivers and important for recreational fishing and water supplies. For much of the life of the of the operations tailings were directly discharged into the creek, and in latter years stockpiled or very close to it. Little rehabilitation was carried out at mine closure. The result was erosion and subsequent deposition on the banks of the creek downstream. Direct emissions of adit water and the consequential emission of contaminated ground water to the creek continue to affect water quality. Contaminant loads discharging from the mine and tailings comprise 70% of the metal load in the catchment and are by far the largest single source. Acidity data suggested that the introduction of systems to introduce alkalinity could be effective in ameliorating the residual acid drainage impacts in the Storys Creek catchment. After a period of investigations and trials which proved their effectiveness, treatments adopted have included the following: relocation of tailings to a constructed and clay capped disposal area and rehabilitation of tailings area; crushed limestone addition to stream flows; crushed limestone addition to creek banks and exposed tailings; sealing of a drainage Adit; and construction of an anoxic drain to generate alkalinity to surface waters draining to old mine workings. These innovative treatments have resulted in a marked improvement in water quality draining from the area. The anoxic drain is believed to be one of the few, if any, which has been constructed to have generated high levels of alkalinity from clean waters and offers a solution to the clogging problems experienced in such drains in the past. Similarly, the use of crushed limestone in an active stream has proved effective in buffering acid drainage and removing metals from solution.

Jan 1, 2003

By M L. Cramer, N P. Wines

"On 9 February 2014, bushfire embers landing on exposed coal in a disused pit at the Hazelwood mine in Victoria’s Latrobe Valley ignited a coal fire that burned for 45 days. The fire was the largest and longest burning mine fire to occur in the Latrobe Valley (Hazelwood Mine Fire Board of Inquiry, 2016). Two Victorian Government Boards of Inquiry have been held into the Hazelwood mine fire. The most recent, in 2015, included consideration of the regulation and implementation of rehabilitation practice at Hazelwood and the other two brown coalmines of the Latrobe Valley (Loy Yang and Yallourn; Government Gazette, 2015).The 2015 Hazelwood Mine Fire Board of Inquiry commissioned Accent Environmental Pty Ltd (Accent) to undertake a review of the financial mechanisms for mine rehabilitation and closure adopted in Australia and overseas (Accent, 2015). Specifically, Accent was engaged to identify ‘any practical, sustainable, efficient and effective alternative mechanisms to ensure rehabilitation of the mines as required by the [Victorian] Mineral Resources (Sustainable Development) Act 1990’ in accordance with Terms of Reference 10 (c) (Government Gazette, 2015).The review by Accent included consideration of a range of financial instruments such as bank guarantees, trust funds and insurance. It considered a number of financial assurance systems in operation in Australia, New Zealand, the European Union, Canada and the United States. These systems included: full and discount financial assurance systems predefined liability proportion systems pooled fund systems the use of post-closure financial mechanisms such as trust funds (Accent, 2015).What lessons can be learnt from other jurisdictions? Are there financial mechanisms already in place that could allow the Victorian Government and the mine operators to manage the risk of rehabilitation default3, lower rehabilitation liability, attain site rehabilitation objectives and allow eventual site relinquishment?CITATION:Cramer, M L and Wines, N P, 2016. Global lessons for a local problem – rehabilitation bonds and Victoria’s Latrobe Valley coalmines, in Proceedings Life-of-Mine 2016 Conference , pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By Iwu GO, Almond DP, Joasoo _

The gravimetric integral Knudsen effusion method was used to measure cadmium activity values in binary liquid In-Cd alloys in the range 523 to 573 K. The activity measurements together with other studies from the literature indicate that special bonding conditions exist in the melts near a composition corresponding to InCd3. Sound velocities in In-Cd melts were also measured using a precision pulse-echo over- lap method in the range 404 to 953 K. The frac- tional deviation of experimental and ideal isentropic compressibilities at 623K shows a functional dependence on composition with a pronounced maximum near the composition 75 at.%.

Jan 1, 1980

By I Ametov, S Harmer, R Alford

A process that allows selective flotation separation of low Cu/S ratio minerals (chalcopyrite and pyrite) from high Cu/S ratio minerals (bornite and chalcocite) from a mixed copper mineral concentrate under controlled oxidative-reductive potential conditions has been developed. The process has been extensively tested on samples with varying mineralogy using laboratory batch flotation tests and mini pilot plant trials.In this process, the mixed final copper mineral concentrate is purged with nitrogen, and then treated with sodium dithionite to achieve a slurry Eh in the -200 to -100 mV standard hydrogen electrode (SHE) range. Flotation was then carried out using nitrogen gas. As a result, a low Cu/S ratio concentrate (<1.3) and a high Cu/S ratio (>1.6) tailing stream were produced. QEMSCAN analysis of the flotation products showed that more than 85 per cent of the chalcopyrite and 95 per cent of the pyrite reported to the froth concentrate. Chalcocite and bornite were almost evenly distributed between the concentrate and tailing streams.Surface analysis studies, focused on the mechanism of separation, showed that at a negative redox potential xanthate and possibly dixanthogen are the dominant hydrophobic species on the surface of chalcopyrite and pyrite. As a result, the flotation of these minerals remained unaffected. In contrast, a much lower concentration of xanthate species on the surface of chalcocite and bornite particles was observed. Therefore, it is likely that at low Eh the copper xanthate complex desorbs from the chalcocite and bornite surfaces, causing a decrease in surface hydrophobicity and the diminished floatability of chalcocite and bornite.CITATION:Ametov, I, Harmer, S, Grano, S and Alford, R, 2014. Selective flotation of chalcopyrite and pyrite from a mixed copper mineral concentrate under controlled redox potential conditions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R Thompson, J Miedecke, D Handel, E Tomicek, D Tulloch

"The Mine Haul Road Optimisation Alliance (HROA) is a unique Australian industry–academia collaboration that has been developed to support mine haul road operators. The alliance integrates industry, end-user service providers and academic research expertise in mine haul road design, construction and operation to identify, quantify, implement and monitor the various equipment, materials and road management strategies and solutions required to drive haulage productivity improvements.Initially, a broad overview of the university–industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis internationally. This insight places into context the opportunity that strategic collaborations present, to drive productivity and efficiency in mining, while also delivering innovative technology solutions.Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry collaborations can deliver a more robust and needs-driven solution to mine haul road design, performance and management, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service providers alike form the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and practical, implementable solutions.The paper concludes with examples of how the alliance collaborations work in practice to deliver focused mine haul road research outcomes, together with the mechanisms used to ensure industry needs are met through end-user driven research solutions for enhanced operational performance.Citation:Handel, D, Miedecke, J, Thompson, R, Tomicek, E and Tulloch, D, 2016. Driving Haulage Productivity Improvements through Industry–Academia Collaboration, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 243–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

Successful restoration of Ballarat region alluvial gold workings to Box-Ironbark forest requires realistic evaluation of techniques. A stocking level threshold of 68 percent is used to rate the success of 'broadcast' seeding of E. microcarpa, E. Melliodora and E. Leucoxylon.Failure necessitates follow-up enrichment planting with tubestock, which is considered undesirable, interalia, due to pathogen, spacing and economic problems.

Jan 1, 1992

By C Katonga

Mindola mine is currently the deepest mine in the Zambian copper belt. Stoping is currently active to 1330 m below surface with long range plans indicating future production from 1590 m level. The orebody is tabular and dips between 55o to vertical. The thickness varies from 8 to 14 m. The vertical crater retreat method of mining was first introduced at Mindola mine in the late-1980s following several trials that helped define the design criteria for its application. Over the last ten years the method has been continually modified to improve safety and maximise ore production. For example, due to the weakness of some rock units within the orebody formation and the instability of the hanging wall, the last VCR slices are usually between 8 - 10 m thick, and efforts are being made to strictly apply shrinkage method in order to reduce dilution. Recent advances in mining technology in the areas of equipment, blasting techniques, rock mechanics and materials handling have been employed to increase the overall productivity of the mine. Large down-the-hole machines capable of drilling 165 mm diameter blast holes, up to 80 m long are used in stoping. Each stope produces up to 20 000 tonnes of ore per month and can last for three months. Heavy systematic ground support of VCR development has significantly enhanced safety for mining crews and equipment. Crater mining has not only improved productivity and enhanced safety, but also overcome various problems associated with conventional sublevel open stoping previously employed at the mine. This paper discusses the technical and operational aspects of vertical crater retreat mining at Mindola mine during the last ten years. The changes in mining method are often accompanied by changes in mine design, blast design, mining equipment, ground support and operating practices.

Jan 1, 2000

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Salmimies

Choosing a ceramic capillary action filter is often favoured in processes where low energy consumption is important, such as the dewatering of iron ore. In addition, the performance of the filter medium is essential, and the possibility to regenerate the medium is an advantage compared to other types of filter media. Although low, roughly 8 - 9 w-per cent for iron ore concentrate, and even cake moisture is the primary goal of dewatering, the introduction of better filtration processes can result in significant improvements of water economy and material efficiency.As industrial beneficiation processes are often complicated in their chemistry due to impurities originating from the ore itself, from the up-stream processing equipment and from the process water used, the characterisation of the filter media after usage might provide relevant information on what actually takes place during long operating periods. The aim of this study was to obtain new information on the fouling of fi lter media in an iron ore process to enhance and develop the regeneration process of the media in the future.X-ray diffraction and scanning electron microscopy were used to characterise ceramic filter media used in the dewatering of magnetite. Principal component analysis and discriminant analysis were introduced to identify trends in the data. Two types of media blockages were found to play an important role in an acidic iron ore dewatering process: fouling by slurry particles and by in situ crystallisation of a calcium compound, of which the latter originated from the combination of process water and process chemistry.

Jul 11, 2011

Mining regulatory authorities worldwide mandate frequent inspection of winder ropes used in shaft-equipped underground mines and ski lifts. Visual inspections are effective in identifying and assessing the type and severity of damage found in the exterior of the rope. In addition, electromagnetic or permanent magnet-based methods are used to identify broken wires, corrosion damage and other anomalies that occur anywhere within the core of wire ropes made of steel, which is a ferromagnetic material. The magnetic methods yield the loss of metallic area due to wire breaks and other damage in the ropeÆs section as well as local flaws that give rise to discontinuities in the magnetic field. The quantitative measurement of the loss of metallic area is indirectly related to the loss of breaking strength that is commonly used as a rope discard criterion. The ropes used in a mine winder in the Goldfields of Western Australia are inspected using Meraster 120B permanent magnet-based rope tester and their condition is assessed against published discard criteria.

Jan 1, 2003

By Y Zhang

Being analysed systematically, the factors influencing the production of fully-mechanised coal face have been divided into geological, mining technical, and management groups. Artificial neural network-expert systems (ANN-ES) are established to decide the influencing factorsÆ membership grade; genetic algorithm-artificial neural network (GA-ANN) are used to decide the weights; fuzzy comprehensive evaluation method is used to calculate the integration indexes. Finally, the GA-ANN model is established to forecast the production of fullymechanised coal face. It is proved that the model is reliable with higher precision. The production of fully-mechanised coal face is influenced by many factors. However, some influencing factors are neglected by the traditional forecasting methods, the results of which are not precise and hardly be used as a guide for mine production and management. The relation between the production of fully-mechanised coal face and its effecting factors is analysed, and the meta-synthetic AI approaches are used to forecast the production of fully-mechanised coal face.

Jan 1, 2003

By Bailey H. W

Power supply for remote mining developments is compared with supply to the general public with the conclusion that the private power plant operator has many opportunities to minimise his costs which are not open to public utilities. The main features of diesel, gas turbine and steam power plant and the limitation upon their application which may be imposed by the fuels available and the local conditions at remote sites are outlined. Reference is made to the value of joint examination by the mining engineer, metallurgist and power engineer to decide how to make best overall use of capital, labour and energy in co-ordinating the design of power and process plant and in setting no more than adequate standards of reliability and efficiency. Fluctuations in world markets make it difficult to plan mining operations to a firm time base. Suggestions are made to minimise the financial risk in forward expenditure upon power plant which in large sizes due to longer construction time may have to be ordered before a final decision is taken upon the mining development it is to serve.

Jan 1, 1973

By C Mpodozis

Central Andean (22¦S to 34¦S latitude) Miocene giant ore deposits share common features that reveal their origin. Tectonic and magmatic features include a relation to a shallow subduction zone, an association with the waning or initiation of a magmatic episode, emplacement at the time of uplift associated with crustal thickening and formation at times of major magmatic changes along the Andean margin. Rare Earth Element (REE) signatures in magmas erupted near the time of mineralisation indicate a progressive change from equilibration at depth with a hydrous, intermediate-pressure amphibole-bearing mineral residue to equilibration with an anhydrous high-pressure garnet-bearing assemblage. These features point to a common history. First, a relatively shallow subduction zone leads to hydration of a cool mantle wedge providing a source of fluids which builds up over at least several million years. Arc magmas formed at this time equilibrate with a hornblende-bearing residual mineralogy. Second, a compressive tectonic regime leads to crustal shortening and thickening that facilitates entrapment of arc magmas in the crust. Eventually, the magma-weakened crust yields to horizontal compression causing rapid crustal thickening. Fluids required for mineralisation are liberated as amphibole-bearing assemblages break down to garnet-bearing ones and over pressured fluids are released from plutons. Mineralisation subsequently ceases in the region unless continued dehydration of the slab and mechanical thinning of the continental lithosphere causes the previous conditions to repeat. The type of mineral deposit generated depends on the pre-existing continental lithosphere and the distance from the trench.

Jan 1, 1999

Optimising a mining or a quarrying operation about the overall cost is quite a challenge as there never is a situation where we have exactly the same conditions regarding rock properties, explosives' performance, mining equipment or evironmental restrictions. The amount of endless influencing parameters and variables make the evaluation process difficult. The enormous progress we have seen during the recent two decades in computing has however significantly increased our ability to evaluate and process the information gathered, and refine our existing prediction models. Refined models demand an increasing volume of good quality information to show reliable conformity with reality. There is a great need for co-operative work in the mining and quarrying society if we shall be able to screen all available data, systematically find the key-parameters influencing the results and to build robust scientific models. No organisations today have all the skilled people needed or can afford to hire the necessary specialists in all the overlapping branches. This paper highlights some on-going work where the Dyno Explosives Group is adding some new pieces to the giant jigsaw puzzle representing the ultimate model of the mining and quarrying operations we all of this society would like to see completed.

Jan 1, 1995

By Williams DJ, Battino S

The rapid crushing technique for the measurement of gas content of coal consists of accelerating the rate of gas desorption from coal by crushing. This technique allows the determination of gas content in the space of hours rather than days or weeks as required for the traditional slow desorption technique. The crushing technique is used particularly when gas content determinations are urgently required for mine safety purposes. The method is now routinely used in underground coal mines of NSW and to a lesser extent in QLD. Despite the rapidity and efficiency of this method, concerns have been raised upon the reliability of the method to deliver accurate results. Experience in Australia has shown that there is in fact some discrepancy in results between gas laboratories using the rapid crush technique. The development of rapid crushing techniques for seam gas content measurements in Australia and the main causes of variability in the gas content test results were investigated. The gas laboratories participating in the gas content testing were CSIRO Division of Coal and Energy, BHP Technical Services and GeoGas Pty. Ltd.

Jan 1, 1998

By R E. Hobbs, O Grabandt, C Das

Mine hoisting is carried out from depths of up to 4 km. At extreme depths, the ropes are so heavy that a large part of their capacity is employed in lifting themselves. Consequently, deep mines have an intermediate winding station. Even at lesser depths, the weight of steel wire rope reduces the possible payload. Of course, steel wire ropes have, over the years, demonstrated exceptional reliability and acceptable lifetimes. The use of steel is supported by well established operating rules and sound NDT methods. However, lightweight ropes made from synthetic fibres could be of great benefit to the industry, with the prospect of eliminating two-stage winding and substantially increasing the payload. Initial tests, in cycling over sheaves, have demonstrated that an aramid co-polymer fibre, Technora« is a potential candidate for this type of service. This paper presents results of testing carried out on aramid co-polymer and other synthetic fibre ropes. These results hold out the prospect of exceptionally long lives. Possible NDT methods are explored including optical fibres with optical time domain reflectometry or with Brillouin scattering, plus a method based on carbon fibre continuity. The introduction of aramid co-polymer ropes will require extensive testing and a program is proposed in the format of a Joint Industry Project.

Jan 1, 2005

By J Czerwinski, M Kasper, M Wyser, N Heeb

The VERT project 1993 - 1998 laid the technical foundation for curtailing the emission of fine particles from diesel engines at Swiss underground workplaces. The targeted maximum was 100 ¦g/m3 EC. Extensive laboratory and field investigations demonstrated that this specification is only attainable with modern diesel particulate filter (DPF) systems that almost eliminate particles in the entire lung penetrating size range from 20 nm to 2.5 ¦m. In January 2000, Switzerland mandated compulsory particle filters in underground workplaces, particularly in tunnelling, irrespective of engine age, size and type. After the implementation, the particle concentration in the respiratory air was below 40 ¦g/m3 EC, compared to earlier values of up to 750 ¦g/m3 EC. Deployed DPFs have proven filtration rates of 99 per cent in the entire size range of alveoli intruding particles. The DPFs are as durable as the engine, suffer no ageing and require minimal maintenance. The failure rate is below three per cent annually. Of the 6000 retrofitted construction machines in Switzerland, about 400 are deployed underground. Prerequisites for this quality are a sophisticated certification procedure, electronic monitoring of DPF operation and meticulous periodic exhaust gas inspection of the engines.

Jan 1, 2005

By A Garg

Squeezing can occur both in hard rock and in jointed rock mass as a result of over stressing. It is related to time dependent shearing, ie shear creep and is associated with the volumetric expansion (dilation) and radial inward displacement of the tunnel surface. While planning a tunnel in hard rock under a high cover of the order of 2 km it is desirable to identify the potential squeezing ground conditions and to select appropriate excavation technique and the support measures. There are several solutions to counter balance the squeezing ground viz over excavation of tunnel profile, assessing appropriate excavation technique, provision of a ductile primary support and time for providing tunnel lining. Low drivage rates and high cost due to support failures requiring rectification arising out of poor anticipation of tunnel closures and support pressures are major problems associated with tunnelling under squeezing ground conditions. Under squeezing ground conditions, the deformation will be gradual, therefore, in order to absorb deformations yielding supports are quite useful as primary support which provide a reliable low initial support pressure and permit uniform stress relief of the surrounding rock along with preventing rock from ravelling. The paper discusses the various factors which influence the selection of appropriate excavation technique and support measures in hard rock under squeezing ground conditions.

Jan 1, 1999

By B L. Coulter, E Wightman, A S. Burrows

With their commitment to sustainable development in an increasingly carbon-constrained world, many resources companies are focused on reducing the energy required to create their final products. In particular, the comminution and smelting of metal-bearing ores are both highly energy-intensive processes. If resource companies can optimise the energy efficiency across these two processing stages, they can directly reduce their overall energy consumption per unit mass of metal produced and thus reduce their greenhouse gas footprint. Traditional grinding and flotation models seek to improve the efficiency of mineral processing, but they do not consider the energy used by downstream metal production, eg smelting and refining. Concentrators and smelters individually may be running efficiently, but are they optimising energy consumption of the overall system? A key step towards answering this question is to understand whether it takes less energy to remove an impurity in the concentrator or the smelter. Analysis of the complete concentrator û smelter process chain may show that there are times when the concentrator should use more energy to reduce the overall energy requirements across the mill and smelter. The new methodology discussed here will integrate downstream processing energy with mineral processing energy, to find the overall most energy efficient circuit design and operating strategy. The proposed methodology includes: determining what grade and recovery positions can be achieved in the concentrator by using different combinations and amounts of grinding and regrinding, thermodynamic calculations of the energy used to process the different concentrate grades to metal, and integrating the concentrating and smelting models to find the lowest total energy for the system. A case study which investigates the effect of increasing regrinding energy on the overall mineral processing û smelting energy consumption is presented. For the copper-nickel sulfide ore investigated the addition of regrinding results in 11 per cent less energy being used in the overall concentrator û smelter process chain per tonne of metal produced. Although regrinding is often seen as an energy-intensive process, in this case study the use of 1 kWh of energy for regrinding reduces the overall energy consumption by 12 kWh. The new mill to melt methodology will allow companies to model energy consumption from mill to smelter with a view to reducing the energy-intensity and greenhouse gas footprint of their processing and smelting operations.

Jan 1, 2009