Search Documents

By D Ford

BHP BillitonÆs new rotary iron ore car dumper installation at Finucane Island (Port Hedland) was constructed to increase the total capacity of the port facility from 110 Mtpa to 120 Mtpa and to allow for incremental capacity increases in future. The arrangement of the dumper is similar to other car dumper installations existing on site. To construct the facility, approximately 120 000 m3 of material was excavated in six months, to a total depth of 22 m. The saline water table was nominally 6 m below ground level and the materials excavated varied depending on depth, ranging from sand to mangrove muds. There was a need to retain the sides of the excavation and limit the amount of water from entering the excavated area. This was required to allow excavation to progress and had to be maintained during construction of the permanent concrete and steel facility. The excavation was backfilled progressively as construction progressed. Various retaining wall methods were investigated with the preferred option being sheet piles secured by walers and ground anchors. Detailed electronic models were developed and assessed to complete the final design arrangement. Dewatering bores around the perimeter of the excavation removed the groundwater to intercepted sumps within the site. A strict and methodical program was developed to monitor the integrity of the temporary works and the quality of the groundwater. The works were completed on time despite the following challenges being encountered: availability of resources and equipment, movement of mobile plant on æboggyÆ materials, difficulty driving sheet piles into material at depth, drilling of ground anchors to 32 m, grouting of ground anchors, greater than expected groundwater flows, and the risk of hydrocarbons within the groundwater. The lessons learned from the use of the retention system and, in particular, the associated construction challenges overcome, provide a sound basis for similar work in this buoyant resource market. The conference paper describes the temporary works options investigated, design considerations and processes, construction methodology and challenges encountered, and the monitoring systems developed. Lessons learned are also discussed.

Jan 1, 2007

By G S. B Karunatillake

Following a pre-feasibility study, Mount Isa Mines commenced a feasibility study on the deposit of the George Fisher Mine in May 1997. Board approval was granted in May 1998 to construct a 2.5 million tonne per annum mine and to upgrade existing concentrator and smelter facilities. The world-class George Fisher zinc-lead-silver deposit is located approximately 22 kilometres north of the city of Mount Isa, in north-west Queensland and is 2.6 kilometres north of the existing Hilton Mine. It will be a large-scale underground mine, sustaining a profitable zinc-lead-silver business in Mount Isa for at least ten years. This paper will outline the details of the mine that was developed during the feasibility and design phase. It will include a description of the mining methods, ventilation, fill, ore handling, services and infrastructure. The utilisation of existing assets and the development of innovative ideas were essential to the successful economic development of the George Fisher Mine.

Jan 1, 2000

By B Murphy, T Mattsson, R Crosbie, T Maksimainen

"An Outotec e500 TankCell, with 500 m³ of actual flotation volume, was commissioned at the Kevitsa Cu-Ni-PGE concentrator in northern Finland during 2014. This flotation cell was implemented at the head of the existing copper circuit as the first Cu rougher flotation cell. This was the first flotation cell of this size to be run under production conditions by any supplier anywhere in the world.The cell has been in continuous operation since start-up in October 2014 and has provided improvements in metallurgical performance at very low specific power consumption. On average, the cell has recovered 71 per cent of copper contained in the 0.37 per cent Cu flotation feed at a concentrate grade of 17 per cent Cu. The specific power consumption for the cell (excluding blower power) is typically around 0.4 kW/m³.After start-up, the impeller speed and superficial gas velocity were varied and the impact on metallurgical performance measured. In this paper a review of the cell operation at Kevitsa is given. Furthermore, the impact of mixing and gas dispersion on metallurgical performance is presented.Citation:Crosbie, R, Mattsson, T, Murphy, B and Maksimainen, T, 2016. Metallurgical Performance of Outotec's e500 TankCell at the Kevitsa Cu-Ni-PGE Concentrator, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By T Brown

Australia is now committed to the most significant period of infrastructure investment since the 1960s and the current climate of project finance and public private partnership (PPP) model uncertainty means it is imperative that the affordability and certainty in delivery of infrastructure projects is maximised.In light of the current and forecast levels of infrastructure investment it is worth drawing comparison with a similar period of Australian expansion when the nation’s first railways were constructed. Similarly to over a century ago, we are following a trend in rapid development and are already reaping the inefficiencies that could be avoided with broader technical planning and improved client coordination.The original rail networks were developed by the individual states before they combined to form a Federation of states in 1901. As a result of the adoption of different gauges by 1917 a passenger wanting to travel by train from Brisbane to Perth had to change trains six times.Similarly in 2011, there is little parity between Australian states on the quality requirements (performance specifications) for road tunnels. Differences between states start most significantly with the size of the specified traffic envelopes, thus the size of tunnel required. Where ambiguity and differences exist in project documentation, performance specifi cations (PS) and broad technical requirements for road tunnel projects, any associated risk in interpretation ultimately ends up being incorporated in the bidder’s (constructor’s) final sell price.Whilst not nearly as inconvenient as having to change train at each state border, and largely unnoticed by the general tax paying motorist, this paper examines examples of apparent minor differences in Australia’s recently constructed road tunnels to highlight the differences in road tunnel specifications.The paper identifies how these small differences manifest themselves in major price penalties between projects and further, highlights the need for further specification review, refinement and standardisation across road tunnel jurisdictions to increase road tunnel affordability.

Mar 8, 2011

By M Grigorescu, J H. Hodgkinson

The expansive, open cut iron-ore mines in Western Australia typically experience few days of rain per annum, often amounting to less than 250 mm. Unlike mines where rainfall is frequent, they may be less prepared for extreme rainfall events. Such events can cause erosion, flooding and sedimentation, drainage alteration, spoil and stock heaps wetting and effect slope stability. Such impacts may threaten personnel safety, infrastructure, and production. The CRATER (‘Climate Related Adaptation from Terrain Evaluation Results’) framework collates and interprets a mine’s pre-existing data and semi-quantitative information to assess vulnerability to, and ultimately plan to avoid or minimise, flood-related hazard to infrastructure, people, downtime, environment and revenue. Outputs assist decision makers to design investment strategies for minimising mining operations’ vulnerability to climate. Previously developed for smaller, wetter mines in Queensland’s coal region, the outputs provide a hot-spot map, fault tree analysis and an assessment of the mine’s capacity to adapt. The multicriteria evaluation (MCE) within a geographic information system (GIS), equally suits iron-ore mines’ siteconditions (elevation, slope, drainage, soil and vegetation) to identify critical inundation areas. Hotspot results provide target zones for in-depth fault-tree analysis that, in turn, present a range of sitespecific adaptation options. Rainfall-intensity and the number of rain days since the 1970s have increased over central and eastern parts of the Pilbara Region. While tropical cyclones may become less frequent, they are projected to increase in intensity. Although some parts of the Hamersley Ranges receive more than 500 mm per annum, rainfall in the Pilbara is generally very low. Therefore, experience of the impacts of extreme rainfall events in the constantly changing topography of Western Australia’s iron ore region may be sparse. Minimising potential effects can be proactively assisted using CRATER.

Nov 8, 2021

By M M. Hilden, M S. Powell, B Foggiatto

In an environment of decreasing ore grade, increasing costs and uncertainty with respect to commodity prices, the industry could benefit from evaluating alternative technologies and innovative circuit configurations. The flexible circuit approach suggests that the design of grinding circuits can be adapted to changes in feed properties and economic conditions. Advances in modelling and simulation are enabling metallurgists to predict the performance of more complex circuit configurations with increased confidence. Ore variability information and processing costs may be used as modelling inputs to determine the optimum processing conditions at a given time. A case study has been completed demonstrating the value of combining a flexible circuit with a model-based optimisation of the process. Ore properties and equipment performance data obtained in operating plants have been used to model and simulate flexible circuit configurations.This paper explores strategies to introduce flexibility to existing circuit configurations when processing ores with high variability. Multicomponent models incorporated in the model developers’ kit (MDK) allow the simulation of more complex and flexible circuits. This capability enables demonstration of the potential to enhance metal production through adapting processing routes according to the ore type being processed. The simulation of different flow sheet configurations allowed the definition of the best option for maintaining the metal production when treating lower grade ores, highlighting the advantages of flexible circuit configurations compared with a one-process-fits-all approach.CITATION:Foggiatto, B, Hilden, M M and Powell, M S, 2014. Advances in the simulation of flexible circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 391–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named 'RAMOCE' has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski's rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

By J Pan, B-J Shi, X-B Li

The granulation behavior of specularite fines which possess poor ballability was studied with limonite fines as a function of nuclei particles and adhering fines. The results show that the permeability of granules deteriorated as the ratio of specularite fines increased in the mixture, and the optimal granulation moisture content also decreased. The granulation kinetics results demonstrate that the adhering load of specularite fines increases rapidly within three minutes and then levels off. With increasing specularite fines ratio, the adhering speed is accelerated but the granulation duration needs to be longer to reach adhering balance. The microstructure of granule quasi-particles indicates that the fine limonite particles act as binders to bond together the specularite particles which are dispersed in the adhering layers. This can improve the adhering strength of the granules. Hence, the granulation behaviour of specularite fines can be improved by blending them with fine limonite ores which have high adhering capabilities.CITATION:Zhu, D-Q, Li, X-B, Pan, J and Shi, B-J, 2015. Granulation behaviour of specularite fines in ferrous sinter mixtures, in Proceedings Iron Ore 2015, pp 91–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Recovery of gold by smelting zinc dust concentrate has been carried on at Lake View and Star, Ltd., since July, 1930, when the Merrill-Crowe precipitation plant was first put into operation.Part I describes the development of current gold-room practice, commencing with the clean-up of the MerrillCrowe plant, a procedure that has not materially changed since its inception, and then shows how modifications to straight roasting and smelting became necessary, following a gradual increase in the copper content of the ore treated by the mill.Present smelting practice converts most of the copper into a mixed copper-lead matte, thE sulphur being supplied by the addition of flotation concentrates containing about 35% sulphur as pyrite. The process yields gold bullion of a sufficiently high grade to send to the Royal Mint, but until 1943, suffered from the disadvantage of giving matte and slag by-products high in gold and silver, that were not recovered directly but had to be sent to a smelter.Part Il gives details, of experimental work cnrried out since 1943 which led .to a process for the satisfactory and economic recovery of not only the gold and silver, but also the copper from these, hitherto, troublesome by-products. Nevertheless, incidence of matte in a smelt has always been considered undesirable, and it is hoped that eventually it will be obviated by removing most of the copper from the zinc slime before smelting.Part III indicates the methods by which this might be achieved, and outlines the experimental work that has been done up to the present.

Jan 1, 1948

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

By G W. Croft, L E. Krause

The current copper ore handling systems in use at Xstrata CopperÆs Mount Isa Copper Operations are up to 33 years old and have hoisted over 160 Mt at a rate of around 6 Mtpa. The mineÆs production profile is increasing in line with the optimum life of mine plan to over 6.6 Mtpa, which requires a system utilisation and reliability above that previously achieved. Copper ore is hoisted up the U62 shaft, which forms the central part of the U62 ore handling system. In theory this system can cope with the duty planned if the bottleneck is only the U62 winder. To achieve the planned production rate will require increased focus on reliability of each component in the ore handling system so that ore is available at the shaft for hoisting whenever the shaft is available, and the shaft is available for the maximum practical time. Increased availability will be achieved through the outcomes of the study of each component in the U62 system, and the internal ore handling systems that deliver ore from as far as 2 km laterally and 700 m vertically from the U62 shaft. The true capacity of each component is being determined and current performance is being measured with the aim of improving performance through root cause analysis and engineering out the causes of delays. The program began in March 2004 and this paper describes the progress achieved as of April 2005.

Jan 1, 2005

By Pate W. T

This paper describes the development of a dynamic flowsheet simulator for comminution operations. Object oriented software design allows the handling of multiple ore types, blended into multicomponent feed streams. Software objects have been c

Jan 1, 1998

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003

The Fosterville Goldmine in Victoria employs bacterial oxidation (BIOX« Process) to liberate gold from its flotation concentrate. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation even with fine grinding. Once liberated by the oxidation process, the gold is then available for cyanide leaching. While the oxidation process is very effective, it has been found that a portion of the liberated gold can become suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. This paper discusses investigations into the causes of the loss and also describes the successful use of quebracho tannin in reducing colloidal gold loss. Laboratory and subsequent plant trials, showed a gain of 2.6 per cent in overall gold recovery based on mill feed and waste stream data.

Jan 1, 2009

Gas dynamic phenomena, particularly instantaneous outbursts of coal and gas are problems experienced in gassy, highly stressed coal, both usually the result of depth. Diff- erent mining geometries present different opportunities for seam gas to escape, starting from the virgin condition unaffected by mining and ending with the mining of the coal. The mining of the coal varies from entering a virgin seam cross-measure, heading out into virgin seam, advancing longwall faces into virgin seam and extracting developed blocks from large longwall retreating blocks to small pillars. Each method has its particular gass- iness patterns and particular stress patterns, both changing to some extent with time, and changing as mining progresses. Geological structural anomalies are the cause of gas and stress anomalies, causing in turn greater gas and stress manifestations. Pre-drainage of gas from the working seam not only degasifies the coal but causes it to shrink and so may affect stress as well as gas patterns. Unfortunately prior degasification is not all benefit, and there are some d13- advantages to its use. Also although it is possible to degasify places ahead, gassiness will return if drainage holes are shut down or sealed up and other deleterious aspects may be induced. Research should continue into the problem of instantaneous outbursts of coal and Gas.

Jan 1, 1986

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Short KC

The Hunter Region, with a major part of the coal resources of New South Wales and a long history of coal mining, has experienced a rapid expansion of coal resource development in recent years. While there are inevitable conflicts between mining, urban development and related infrastructure, and between mining and other resources, the application of sound planning practices, and improved co-operation and co-ordination among the various parties, helps to reduce such conflicts. The planning process involves consideration of factors such as transport- ation (including port facilities), mine subsidence, provision for surface facilities, a,iC the need for buffer 'ones. In addition, provision must be made for urban expansion, often co-existing or in close proximity to present or future coal mining development. Approval of coal mining developments takes place within the legislative framework of the Environmental Planning and Assessment Act, 1979 (EPA Act), the Coal Mining Act, 1973 (CM Act) and the Mining Act, 1973. Considerable effort has gone into stream- lining and co-ordinating the procedures under these Acts. The EPA Act provides for regional and local environmental plans, as well as a linked process of development control and environmental impact assessment. The CM Act provides for the grant of exploration and coal mining titles and mechanisms for the responsible management of Mining.

Jan 1, 1987

Diamonds occur in N.S.W., Victoria and north west Tasmania. Diamonds from different areas appear to have their own characteristics, lending weight to the suggestion that three or four different sources (different in location and age) have produced the diamonds found in alluvials at quite a number of locations in Eastern Australia. Explorers for kimberlites in Victoria must overcome a number of field difficulties. The writer's approach attempted to find exploration targets by literature search, noting unusual garnet occurrences, and by relating records of diamond occurrences to described mining activity. While the records are biased towards gold, the study did lead to a pipe, located well away from known diamond-bearing alluvials. Core from one test hole has shown this intrusive to include an alkaline ultramafic breccia with many kimberlitic affinities - a breccia containing mantle-derived minerals, but not a true kimberlite. (A detailed rock description is appended to this paper, but is not the purpose of the paper.) This result enhances the possibility that kimberlites may occur in Victoria, on or near large scale faults or grabens. The depth of fracture penetration may have been different

Jan 1, 1979

Upgrading of Indonesia's Bauxite by Washing Method There were eight bauxite samples used in this research, three samples from Kijang contain total SiO2 18.36 - 29.16 per cent, Al2O3 40.12 - 48.36 per cent, Fe2O3 4.27 - 5.13 per cent, one sample from Tayan, contains total SiO2 4.69 per cent, Al2O3 38.95 per cent, and Fe2O3 19.67 per cent, and four samples from Mempawah contain total SiO2 33.5 - 44.8 per cent, Al2O3 29.8 - 35.9 per cent, Fe2O3 7.29 - 9.88 per cent. All of those bauxite ores have not fulfilled the requirement for Bayer process yet; therefore simple up-grading using a rotary drum scrubber is needed. The scrubbing process was carried out with time variable up to 60 minutes with solid percentage applied was 50 per cent and rotary speed was set up 30 rev/min. The bauxite was washed by following steps: scrubbing, screening, drying, and finally it was analysed to show chemical content. The washed bauxite produced has size fraction that is retained on the 1.7 mm of screen opening. The result of the research shows that the higher alumina content of the raw bauxite, the longer washing time is needed moreover the higher quality of the washed bauxite is produced. The highest alumina content of the washed bauxite was 53.67 per cent with the alumina recovery was 89.66 per cent and the concentration ratio of 84.80 per cent was achieved within 20 minutes of washing time of the raw bauxite (Al2O3 48.36 per cent). The washed bauxite resulted from this research is suitable as a raw material for Bayer process.

Sep 13, 2010