Search Documents

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

Results of investigations on adsorption and desorption of CO M CH and a mixture of the two gases are described.4 Results showed that even when the equilibrium conditions contains 50% Co and 50% CH4, the gas emission in the initia' stages will contain as much as 80% CH . 4 The temperature has a small effect and so also particle size for 1.4-11.2mm. The ratio of CO2/CH gases adsorbed in coal samples depends upon t4he equilibrium pressure and this ratio decreases with pressure. Results of field tests support laboratory studies.

Jan 1, 1988

By Hamblyn S

Oakbridge, in combination with its joint venture partner, Nippon Steel of Japan, is expanding its Bulga underground and open cut mines to meet the growing demand for coal in the Asian market. Expansion works underway will see the Bulga underground mine become a world leader in underground productivity, the introduction of a high capacity dragline into the open cut mine (largest capacity dragline in NSW) as well as a major upgrade of the coal preparation plant (CPP) and coal handling facilities (CHF) to process the increased production. This paper describes the planning and implementation of this major expansion program and highlights the rationale behind some key aspects of the program.

Jan 1, 1995

Mineral deposits in New Zealand whose origin can be ascribed to primary magmatic segregations are associated with mafic-ultra- mafic complexes related to two orogenic episodes which took place during Paleozoic and Mesozoic times. These mafic-ultramafic complexes are essentially of two types. One is ophiolitic and has podiform chromite mineralisation presumably formed below a spreading ridge. The other type occurs as intraplate layered intrusions in which Fe-Cu-Ni sulphides and Fe- Ti-V oxides have formed as a result of liquid immiscibility with the host magma, and have subsequently accumulated by gravity means. Generalised descriptions are given for some deposits in NW Nelson, Fiordland and Marlborough districts.

Jan 1, 1980

The inauguration of a geological department for the mines of North Broken Hill Limited necessitated the provision of accurate plans and sections upon which geological facts and projections might be plotted.Unfortunately, the basic data were very inadequate. For the British Section, sill survey plans were available, but no regular stope plans. Filling surveys had been preserved for many stopes, but on innumerable pieces of tracing linen, without heights of any kind, and not altogether reliable (as indicated by the finding of very inconsistent duplicates). For the bulk of the old stopes no plans exist at all. The expenditure of much time and patience has resulted in the co-ordination of most of the existing stope data, but the British Section must for the rest of its life continue to have surprises in store, as has been the case for many years past. Manufacture and preservation of stope records has, of course, been on a sound footing during recent years. No reliable cross-sections of the British Section were available.The Marsh, Junction, and Junction North Sections have for the most part very poor data. In the North Section, level plans were fairly reliable, and cross sections of the lode made for ore reserve purposes have been preserved for quite a few years. No floor plans of stopes were kept, however, until a couple of years ago.Diamond Drill records vary in quality. Practically none exist for the Junction and Junction North Sections. Logs have been kept for the British Section drill holes, but are...

Jan 1, 1940

This paper presents the findings from an experimental study of the effects of shock and gas penetration breakage mechanisms in rick blasting. A blasthole liner method, which realistically seperated these two basic sources of energy in blasting, was developed and utilized. The use of four different explosives with contrasting detonation behaviour produced a wide variation in the nature of explosive energy transfer to the rock. Through extensive field experiments it was found that, relative to low VOD dynamite, the high VOD emulsion imparted greater shock to the rock and therefore produced finer fragmentation and greater back damage. The comparatively lower heave energy of the emulsion caused less immediate blast results were obtained with watergel and ANFO explosives, which have detonation behaviour and energy partitioning charecteristics lying between emulsions and dynamite.

Jan 1, 1990

By Sauer P

The paper deals with the method of operat- ion, types of construction and sizing of screening machines as well as the selection of suitable screen decks. The application of novel screening mac- hines in hard coal preparation plants is explained in detail by way of examples.

Jan 1, 1984

A combination of the needs of business, employee desires and safety and health considerations is stimulating increasing attention to the time spent by people at work and the timing of that work. Particularly we are seeing: - innovative work schedules for 24-hour mining businesses; and - response from industry to accommodate the needs, even the desires, of employees in return for systems which are more productive and more capital efficient. There appears to be an evolutionary trend for business management to become more sophisticated and responsive to the need for achieving close to best cost work schedules to sustain continuous improvement. The underlying motivating forces driving this trend for improved techniques in organising attendance at, and time spent at work, is the seemingly inseparable combination of technological advance and ever-increasing accumulation of capital. The mining industry has not remained untouched by this thrust for ever-increasing need for best use of labour, to adopt advances in technology and to provide attractive opportunities for putting accumulated capital to work. An essential component of this on-going thrust is a substantial effort by the mining industry to improve the performance of labour by providing most-productive work schedules.

Jan 1, 1996

By Larsen D. F

Minor iron formation related base metal sulphide mineralization occurs in granulite facies metamorphic rocks of the early Proterozoic Willyama Complex. Rock sequences hosting three iron formation related Cu, Zn, Pb prospects from the Thackaringa Group (Suite 3) are described. A caparison of host rock sequences, style of mineralization and facies of iron formations suggests major differences in terms of the overall depositional environment. However, significant similarities are present with respect to the nature and distribution of iron formation facies and the occurrence of chlorite 'alteration' zones in close proximity to mineralization in all cases. The chlorite within these zones occurs in a number of diverse forms in a range of rock types. A comparison of the prospects shows that there is no evidence to indicate that the chlorite in the zones is a retrograde alteration product of former higher grade prograde mineralogies - the chlorite appears to have survived granulite facies metamorphism. The mode of occurence of the chlorite in the 'alteration' zones together with the fact that the association quartz + chlorite + magnetite + pyrite + base metals is cx rmn to all areas suggests that the chlorite is specifically related to the processes which deposited the stratiform iron formations and related sulphides. It is considered that the chlorite precursor was a prenetanorphic alteration product or chemical sediment closely related to submarine hot spring activity which was also the source for chemical sediment precursors of the iron formations, associated lode rocks and Sulphides.

Jan 1, 1983

By Richmond A

Like many industries the coal mining industry has, since the beginning of this century, undergone many changes. Technological advances and the increasing demand for fossil fuels have introduced new mining methods and techniques which allow the extraction of thicker and deeper coal seams at higher rates of production. Most new methods of mining (or for that matter any other processes) introduce problems which the engineers of the industry are expected to face and resolve. Unfortunately, spontaneous combustion has plagued the coal mining industry since the first attempts to mine coal, and is no doubt partly responsible for the reputation that coal mining is a hazardous industry. The financial loss and toll of human lives due to the occurrence of spontaneous combustion of coal in coal mines is enormous, if not incalculable. Its occurrence today is less likely to claim lives, due to both improved methods of working and in the detection of spontaneous combustion sites.

Jan 1, 1983

By Blockley J. G, Laeter J. R

The history of the Ph-Cu-Zn mineralisation in the orthampton Block of Western Australia has been further investigated. It was hoped that (1) Rh-Sr studies on partially-remelled granulites, wall-rocks to the dolerite dykes, should date the dolerite intrusion, (2) Rh-Sr data on hydrothermally-altered dolerite should date the sulphide mineralisation, (3) Pb model ages on the galenas might provide an independent dating of the mineralisation, in addition to any geochemical information that might be derived. Only the second dating aim was fulfilled, but the Pb isotope data, when combined with the Rh-Sr data, have permitted deductions about U, Th and Pb abundance changes during the regional metamorphism, and about a possible source of the ore Pb. In detail the following has been found. (1) The partially-remelted granulitic wall rocks yield a scattered whole-rock Rh-Sr isochron which seems not to have been reset by the dyke intrusion (age 1037 ± 146 Ma, with initial Sr ratio 0.7171 ± 0·0054, MSWD = 111). This date agrees well with that reported previously for granulites from another locality; together theyestablish the time the metamorphic period closed. (2) The hydrothermally-altered dolerites yield a Rh-Sr whole-rock date 434 ± 16 Ma, with initial Sr ratio 0.7072 ± 0·0029 and MSWD = 31, taken as referring to the time of Ph-Zn mineralisation. This contrasts with a report of much older palaeomagnetic and K-Ar datings of the dolerite (not less than 550 Ma, possibly older) and suggests that neither the dolerites nor their heat have had any connection with the mobilisation of the Pbscavenging solutions. (3) The Pb isotope ratios of galenas from the ores yield a well-correlated regression which is not amenable to any of the model-age calculations. (4) The Pb-isotopic trends negate any genetic connection between dolerite and mineralisation, but the country-rock granulites could be the Pb source. (5) Combination of the Rh-Sr dates and the Pb data in a "simultaneous isochrons" construct permits the inference of major losses from the system during the regional metamorphism, in the order U>Pb>Th, with substantial homogenisation of the remaining Pb. This left a wide range in local UlPb and Th/U among the source rocks which eventually were scavenged by the mineralising solutions. (6) These geochemical deductions are shown to be compatible with previously-published information on the abundance ofU and Th in the Northampton Block granulites, which are thus seen to be credible as source rocks for the ore lead.

Jan 1, 1985

By Aziz N

The objective of the paper is to develop an understanding of the influence of caving on powered support rating by examining the geology and support performance at two sites which represent the current extremes in support rating, ie 6/240 Ton supports operating in the Hirst Seam at Solsgirth Colliery, Scotland, and 4/900 Tonne supports operating in the Bulli Seam, West Cliff Colliery, Australia. A conceptual model is introduced which considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata. Different caving mechanisms are identified for the strata of the Hirst and Bulli Seams, ihese mechanisms being related to rock properties, ie to the palaeogeography and depositional conditions at each site, producing caved wastes with different yield characteristics. The results obtained for convergence and support reaction during production cycles at both sites are analysed to show the manner in which support reaction is developed, indicating the importance of high setting load densities in the Bulli Seam. Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations, ie the powered support and the caved waste immediately behind the powered support, is used to further demonstrate the influence of caving mechanisms on support rating.

Jan 1, 1986

By Ward B

Central Colliery was developed to exploit large underground reserves in the German Creek lease. It was planned from the outset as a retreating longwall operation and is the first longwall mine in Queensland. Longwall mining is not new to Australia but all previous experience has been confined to the coalfields of New South Wales. There was no precedent for longwall extraction in the markedly different geological setting of the Bowen Basin in Central Queensland. Various investigations were thus carried out during the initial development of Central Colliery, prior to the installation of the longwall, to ascertain the geotechnical characteristics of the coal seam and the adjacent strata and to predict the performance of the heading and pillar design as mining proceeds to depth. Laboratory tests showed the coal to be weak with an unconfined compressive strength of 9.6 MN/m2. Site inspection and geophysical correlation revealed a shear zone and extensive intraformational shear planes in the seam. The latter were found to exert a controlling influence on rib reaction in the headings. This behaviour was predicted by finite element modelling of the development headings which indicated that mining induced stresses in the coal would be relieved by block movement of the ribs. A chain pillar width versus depth curve was established for yielding pillar design based on empirical and computational methods. This gave pillar widths from 25m to 48m over the proposed depth range of 150m to 300m. Finite element modelling of the 25m pillars chosen for the first gateroads confirmed the overall stability of the design but suggested that rib spall could be significant in the adjacent tailgate. (1) Chief Mining Engineer, Capricorn Coal Management Pty. Ltd., German Creek Mine, Queensland (2) Senior Engineering Geologist, Coal Division, The Shell Company of Australia Limited, Melbourne

Jan 1, 1986

By Wilkins L. G

Ore recovered by North Broken Hill Limited as a result of mining operations at its Broken Hill leases is obtained, at the present scale of working, in the proportions of 80% from the North mine and 20% from the British mine sections, and is composed mainly of a silver bearing, sulphide lead and zinc mineral, in association with the gangue materials mentioned later in the text.The lead-zinc sulphide lode at the North mine is deposited in folds in pre-Cambrian sedimentary schists. These folds pitch north-east at approximately 40° and dip north-west at approximately 60°. In plan the deposit appears as two lenses designated on the mine as the "Southern" and "Northern" ore-bodies.The Southern ore-body yields the main tonnage of crude ore. The sulphide mass here overlies a heavy layer of rhodonite which persists with the pitch of the lode. In the central section of this ore-body the sulphide zone is coarse grained and of high grade with a wide range of minerals in the gangue dilution. Quartz, garnet, ftuorite, rhodonite, and felspar are common, whilst chalcopyrites, pyrites, pyrrhotite and green felspar are often present. The Northern ore-body is dolomitic to siliceous in nature. Crude ore obtained from the British section is predominantly...

Jan 1, 1940

By Haase W. C

The content of this paper will identify recent developments in walking dragline technology including utilisation of planetary swing dnves, high voltage generators, unique bucket configurations and increased machine capacity resulting from changes to front-end geometry. The benefits to mine operators for increased performance, reduced cost, improved availabilities, simplified maintenance, and ease of operation will be identified and discussed. The feasibility and application of the technology as a retrofit on existing equipment will also be covered in the presentation. All the technology being presented has been recently commissioned into operating Australian mining operations and will be presented from a practical, as well as theoretical perspective.When the Marion 8000-Series Dragline was introduced in the early-1970s, it quickly became the industry standard for high productivity and availability. Features like outboard bearing propel, four-chord deep section boom and the over/under fairlead have proven their superiority in thousands of hours of round-the-clock operations in a variety of tough digging conditions worldwide. Marion has currently sold 31 of these 8000-Series Draglines into the Australian mining community.

Jan 1, 1992

The continuously growing coal mining industry of India presently includes shovel dumper combinations in open cast mines, sometimes with dragline mining of overburden, together with the whole range of longwall and bord and pillar underground mining, continuously undergoing fuller mechanisation. This transition from "low tech" to "high tech" systems is now monitored for reliability and provides bases for comparisons of downtime relative to age and make of equipment, whether imported or indigenous, including spare parts, as well as frequencies of particular failures to allow analysis and progressive improvement. Varying geologies complicate technology and equipment requirements, especially in underground mine,s with minimal technological standardisation, but now, reliability in South Eastern Coalfields Limited has been given more importance and superior technological back-up is being developed.

Jan 1, 1991

About 90 per cent of the pre-mining BIF-hosted iron ore resource of the Hamersley Province of Western Australia is of the Phanerozoic supergene martite-goethite type. The remaining ten per cent formed as supergene deposits at ~2000 ¦ 200 Ma, and were later modified by burial to form the Proterozoic martite-microplaty hematite ores. The supergene-metamorphic segment of this general unified model has been challenged by three recently published hypogene-based genetic models for the hematite ores, all requiring meteoric oxidation to produce the ore. The most recent and detailed, by Taylor et al (2001), is based on data from the small Southern Batter and North deposits of the Mount Tom Price mine. The authors proposed that during Stage 1 æoverpressured bicarbonate-saturated basin brines from the dolomite aquifer of the Wittenoom FormationÆ at 150 - 250¦C, dissolved free silica from BIF to produce a stratigraphically thinned, magnetite-carbonate-silicate-apatite rock. In Stage 2, meteoric oxidation of siderite to secondary microplaty hematite + ankerite, and magnetite to martite, at unspecified elevated temperatures and pressures, was followed by carbonate leaching (Stage 3). Finally, during Stage 4, weathering with removal of apatite, produced the typical low-phosphorus, porous martite-microplaty hematite ores of the Tom Price-Whaleback type. However, evidence of both microplaty hematite and martite reduced to magnetite, and of infill silica, apatite, and ferroan chlorite, with late-stage pyrite, in the pore space of martite-microplaty hematite ore, shows that the hydrothermal activity at Mount Tom Price is a post-ore event. Neither pyrite nor ferroan chlorite could resist the oxidation required to form hematite ore. Recrystallisation of microplaty hematite in these infilled zones to a typically coarser form than present in most of the normal ores, is a further supporting factor. A more credible, post-ore alternative to the hypogene genetic model is suggested here. Re-exposure to leaching by ground water of the metamorphosed ore deposits in the Phanerozoic resulted in the partial removal of remnant goethite. Localised modifications in the porous BIF/ore contact zones were driven by exothermic oxygen/pyrite/carbon reactions in the footwall Mt McRae Shale. Cool descending oxygenated meteoric water in the permeable ore horizons, acted as one limb of a thermal convective cell. In the other limb, heated reducing solutions rose through the permeable contact zones, to produce the observed localised modifications of BIF and ore. Expelled silica from the carbonatised BIF invaded adjacent porous ore to form erratic silicified ore zones, and to produce the local quartz vein systems found in the associated overlying BIF.

Jan 1, 2002

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987

Indiscriminate surface disposal of coal waste in New South Wales has created a serious fire hazard and increased air pollution.A survey of numerous dumps, as well as particular investigations of one badly-constructed dump, showed that factors conducive to ignition and propagation of fires in waste dumps were high contents of combustible material (coal, pyrite, wood. paper. grease), size segregation leading to ready movement of air and moisture shape of the dump (e.g. protruding sections or porous junctions), high ambient air temperatures, bush fires, and even deliberate lighting.Control methods applied in the past tended to be haphazard and unsuccessful. Under Australian conditions the technique recommended for control of existing dump fires, based on experimental work, is to spray the dump with a chemical fire retardant (e.g. a 2 per cent solution of sodium tetra borate and ammonium phosphate), to cover the dump with a suitable soil, and to seal the surface with a I per cent solution of aluminium sulphate or sodium metasilicate. The recommended method of dump construction to prevent fires is to level and seal the site, to construct a firebreak around the dump area, and to build a rectangular dump with minimum size segregation and compacted surfaces.

Jan 1, 1971