Search Documents

By B R. Olsson, N Marinopoulos

To establish the design and the capacity of the Stanwell Magnesium Plant, Australian Magnesium Corporation Ltd (AMC) with Fluor Australia has modelled the operation of the magnesium plant using ARENA Simulation Modelling. The reliability model has been used to evaluate: surge capacities required between different sections of the plant; critical equipment requiring standby capacity; the number of trains required for different sections of the plant; and potential capital cost reduction options. The reliability model was established using the detailed Process Flow Diagrams, reliability information from literature and maintenance, operation and start-up experience from the Demonstration Plant. The model was run with different plant configurations to assist AMC in determining the most effective configuration to provide the production capacity at the lowest capital cost. The model was not only able to confirm the plant capacity to the independent technical expert but was able to minimise quantitative risk by minimising the quantities of hazardous materials on site. Fluor Australia provided the ARENA simulation expertise and has used this software for optimising new plant design and to establish improvements in operating plants. Reliability modelling is a normal feature of chemical plant design but is rarely used in the resource industry. The experience gained by AMC in the modelling system has indicated that metallurgical plant design can be improved by the application of reliability modelling.

Jan 1, 2002

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By M Edhammer

In 2007, Atlas Copco introduced an integrated tunnel scanner/profiler. The tunnel scanner, which is integrated into the control system, is mounted on the drill rigs, and replaces the previous variants of non-integrated scanner equipment. The Atlas Copco Tunnel Profiler, which is the name of this system, is currently being used by several contractors and mines on various projects in Scandinavia, Finland and Australia. Atlas Copco Tunnel Profiler can scan a tunnel of 65 m2 in just five minutes and is integrated with the computerised control system for the drill rig. This integration means that the results of scanning are immediately available for analysis on the computer screen both in the drill rig and in Tunnel Manager; a software for tunnel and drift planning.In 2008, a method was introduced for locating the drill rig with a total station navigation (TSN) system, integrated into the control system. TSN systems are used by a number of contractors in Scandinavia and Finland, as well as elsewhere in the world. Using a TSN for navigation is in itself not new, but when this is integrated with the control system it provides the opportunity for individual drill rig operators to use this method, without the direct assistance of a surveyor. TSN gives a very precise indication of the drill rig’s position in relation to the tunnel design. An accuracy of ±1 cm compared with the ±10 cm which is normally obtained with the traditional method using tunnel laser and sight plates on the drill rig’s feeder. The closer a tunnel is blasted to its planned profile, potentially the more is saved in terms of less shotcreting, extra rock bolting and other corrective work. A better quality tunnel is the key to better overall economy and today’s technology makes it possible to achieve that goal in every type of tunnelling and mining project.In addition to total station’s ­navigation and Tunnel Profiler, the concept of ‘high precision tunnelling’ also includes:•Software tunnel planning: Tunnel Manager, Tunnel Manager Pro and Tunnel Manager Measure while drilling.•Measurement While Drilling (MWD)collects the various drilling data and the interpretation of these for the early identification of variations in the rock.•Rig Remote Access (RRA) is a support for wireless or wired communication between drill rig and planning office. The result is being able to send planning data to the drill rig and to simultaneously have the facility for logged files to be sent from the rig to the office. There is an option of an external computer logging in to the drill rig’s control system to view menu screens and settings, and remotely troubleshoot and plan appropriate action.

Mar 21, 2011

By A Jewbali, L Allen

At Newmont Corporation drill hole spacing studies are done to support the business in understanding the cost of collecting additional information (with a specific focus on drill hole sampling density) versus the value of additional drilling in terms of resource risk reduction. For the last 20 years drill hole spacing studies have been executed in an effort to answer the following question: What spacing should the deposit be drilled at to achieve a certain level of resource confidence so that when mining occurs the resource model delivers as predicted ie what is the optimal sampling density? The optimal sampling density supports a resource model that provides a sound foundation for mine planning purposes and resource/reserve reporting. At Newmont Corporation drill hole spacing studies are now a requisite for understanding drill data density needs for new deposits and near mine expansions. This paper details the evolution of drill hole spacing studies at Newmont Corporation in terms of methodology and usage.

May 24, 2023

By K Guilfoyle

AngloGold Ashanti Australia Ltd operates an underground mine below a large open pit at the Sunrise Dam Gold Mine near Laverton in Western Australia. Operations are based on an extensive mineralised zone which has very complex geometry, has a high ‘nugget effect’, and is difficult to interpret and model. Initial underground ore was produced from relatively narrow orebodies dipping from 15º - 70º. Open stopes aimed to selectively extract high-grade ore, using methods including jumbo stripping and longhole drilling and blasting. The complex geology makes it difficult to accurately locate development and stopes in the positions required for profitable production. In narrow stopes, rock mass damage and overbreak dilute ore grades and increase the cost per ounce of gold poured. In flat orebodies, several different techniques have been used to recover blasted ore but overall productivity is low. Thus selective mining can also be slow, costly and recovers only a portion of the available mineral resources. Large longhole open stopes with cemented paste backfill are used to extract multiple zones of mineralisation from the Cosmo and GQ orebodies. Bulk emulsion explosives and electronic detonators are used in all large stope blasts to reduce the risk of misfires and to accurately control blasthole initiation sequences and delay timing. Larger stopes improve productivity and significantly reduce direct mining costs, enabling the use of lower economic cut-off grades which increase the overall recovery of mineral resources. This paper reviews the evolution of open stoping at Sunrise Dam, the various mining methods and drilling and blasting practices used, the results achieved, and the lessons learned.

Nov 8, 2011

By P Revell, B Adair, D King, L Keeney

Grade Engineering®, integrated across the mine value chain, has a pivotal role to play in achieving step change reductions in energy and water usage in mine operations. High levels of gangue rejection in the mine can significantly improve mineral head grades and overall productivity. A highly successful example is described at the Minera San Cristóbal (MSC) operation. The nature of the mineralisation in their “intrusive” ore domains in particular has facilitated high rejection rates (75 % of the mass), with significant upgrading of metal to the “accepts” streams (equating to a 2.6 times upgrade in the intrinsic Nett Smelter Return). Results from a series of production trials have confirmed these strong upgrades, resulting in the transformation of mineralised “marginal wastes” to high grade ore feedstocks. If new approaches to more energy and water efficient comminution and separation technologies can also realise gangue rejection at finer sizes in the concentrator, then preconcentration strategies across the value chain also offer the promise of no wet tailings treatment facilities and greatly reduced volumes of waste streams. This “No Tails” strategy is discussed, along with the integrated technologies needed to realise its effect. The work suggests a pathway and insights of a sustainable future for the Minerals Industry, unconstrained by Energy and Water, along with no requirement to produce problematic disposal streams. This strategy has the potential to significantly reposition the social, environmental, financial, and regulatory context of existing and new mining opportunities.

Nov 10, 2020

By M A. Rhamdhani, K Avarmaa, A Putera, J Chen, G Brooks

Silicon-based photovoltaic cells are currently the most dominant types applied to convert solar energy to electricity. In solar-grade silicon (SG-Si), the control of boron (B) and phosphorus (P) is very critical. Generally, these elements are difficult to remove into acceptable sub-ppm levels from lower grade Si. This study investigates slag treatment as a process for Si refining, focusing on the behaviour of P and B. The experiments were conducted by equilibrating Si-B-P alloys with 43 wt per cent SiO2 – 47 wt per cent CaO – 10 wt per cent Al2O3 slag under inert atmosphere at 1500°C. Different crucible materials were used (Al2O3, SiO2 and MgO), which determined the primary saturation phase for the system and modified the final slag composition accordingly. The samples were equilibrated and analysed with microanalysis techniques (EPMA (electron probe microanalysis) and LA-ICP-MS (laser ablation inductively coupled plasma mass spectrometry)). New standards were prepared and applied in the LA-ICP-MS analyses. Experimental results show that silver is essentially fully dissolved in silicon, as well as most phosphorus with LP ( = wt per cent P in slag/wt per cent P in Si) between 0.1–0.3. The distribution coefficient of boron was measured to be between 1 and 2. The crucible material used had an influence on the phase compositions and slight influence on the distribution coefficients of boron and phosphorus. The experimental results provided new accurate data when considering applicability of slag treatment as a technique for Si refining and Si PV cell recycling.

Jun 19, 2024

By R M. S Watsford, M Davis

In 2015, MMG Limited commenced further action to improve operating margins and establish a blueprint for future growth in the Australian environment. This action was taken in the context of weakening metal prices and high input costs that arose during the Australian minerals boom.MMG was formed in June 2009 following the purchase of the majority of assets of OZ Minerals Limited by China Minmetals Corporation (CMC) through its subsidiary China Minmetals Non-ferrous Metals Co Ltd (CMN).Since formation MMG has been implementing a business model to deliver a standard way of operating. The overarching purpose of the business model is to enable fast integration of acquired assets to realise improved productivity and performance. CMN established MMG as a vehicle to reach their growth targets through further development or acquisition of mineral assets in jurisdictions external to mainland China.The business model is underpinned by the MMG operating model. The operating model defines how MMG is arranged to deliver the company strategy.This paper describes the application of the operating model to the formation of the Australian operations into a single business unit from multiple stand-alone operating sites. The development and impact of the business model on MMG’s performance is also presented.The extension of the operating model to the Australian operations has led to improvement in safety performance, direct costs and productivity. These improvements have been achieved through reducing duplication, simplification of systems and rapid deployment of improvement initiatives.The successful implementation of the operating model to Australian operations strengthens the platform for further growth. Hence, delivering on the aim of the business model.CITATION:Watsford, R M S and Davis, M, 2016. MMG’s Australian operating model – the implementation, successes and learning, in Proceedings International Mine Management Conference, pp 291-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By N Van Buc, E Coroiu

The rapid socio-economic growth of Hanoi City coincides with a corresponding growth of the transport demand. Today, the transport in Hanoi is completely dependent on private modes of transport. Because of the lack of an efficient public transport system and the expected rapid increase in traffic volumes, the movement of people and goods in the urban areas of Hanoi will cause congestion in the present city transport network. The solution of the construction of new roads, or the widening of the existing streets, is very expensive in urban areas and usually causes many social problems due to the resettlement of people. From the point of view of the number of inhabitants, Hanoi City is now over one million. Above this number the international experience shows that the public transportation must be a mass transport system with large capacity, commercial speed and also independent as much as possible from the street network. According to the Hanoi Master Plan for 2020, the Hanoi urban population will be over 3.5 million persons. Also, in the next 15 years, the distances between centre-destination points will be doubled by comparison to 1995.

Jan 1, 1999

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By R Bearman

The importance of crushers in the mining industry declined with the introduction and resultant dominance of AG and SAG based circuits, but the recent move to consider more energy efficient circuits has caused the industry to re-consider the role of crushers.Different types of comminution equipment have different efficiency in the way the energy is applied in the size reduction process. Because of the general trend towards more sustainable production processes and emission of carbon dioxide, energy use has become more important. To fully understand how crushers can contribute to optimising the energy application in comminution circuits, detailed models of process performance are required. Such models need to take into account the mechanical design factors and how the crusher performance changes in response to feed conditions, the control strategy utilised and the wear of the crusher liners.It is also critical to analyse the total circuit, not just the individual crushers. To fully understand the performance of the entire circuit, dynamic simulation should be applied. Without the holistic understanding of the total circuit and the incorporation of transient effects, the full circuit performance cannot be adequately determined and the true energy picture will not be quantified.Based on detailed mechanistic modelling of crushers by the authors and the application of dynamic simulation, the opportunities to optimise the use of crushers for energy efficiency are examined.

Aug 8, 2011

By Nixon J. C, Reynolds C

Three principal features of the ore at Captain's Flat, New South Wales, tend to complicate concentration of the valuable minerals, these being:1. The ore occurs in three more or less separate bodies which vary in texture and mineral ratios. Mining of constant proportions of the three sections, or adequate blending of the ore, is not fully effective, and consequently the flotation section is subjected to feedof varying texture.2. The mineral association in the heavily pyritic ore is extremely intimate. Composite particles exist even at 20 micron sizeI, and probably finer.3. The copper content of the ore averages_about 0,6%, which is high enough to justify recovery of the chalcopyrite in a separate concentrate. A review of the metallurgical history of the mine shows that this feature has been the cause of the several major changes in flowsheet of the flotation section since the commencement of milling.METALLURGICAL HISTORYThe mine started production in January 1939, at the rate of 250 tons per day of sulphide ore, assaying 0·68% Cu, 6·52% Pb, 10·8% Zn, and about 1 dwt. Au and 2 oz. Ag per ton.

Jan 1, 1952

RME has a vision for a new grinding plant operational paradigm made possible by RMEÆs fast, safe Mill Relining System. Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by modifying liner design for maximum life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. Following the introduction, the first section of this paper provides an update describing recent and significant developments within RMEÆs range of Mill Relining Systems, the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The second section outlines RMEÆs vision of a æliner profile versus profitabilityÆ commercial model, developed either intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2007

By D Clarke, I Minniakhmetov

This paper describes the application of the SBRE framework to model the Olympic Dam deposit, one of the largest copper and uranium deposits in the world. Geostatistical simulations are the best practice for quantifying uncertainty in the mineral value chain and estimating resources. However, these simulations are currently undertaken on an ad hoc basis in the mining industry due to the high requirements in computing resources and capabilities in advanced geostatistics. The SBRE project provides a standard framework to test, build, and run conditional simulation workflows, which has been applied to the Olympic Dam deposit. Conventional geostatistical methods face challenges when modelling the Olympic Dam deposit, such as non-stationarity, non-linear correlations, and a large number of grid blocks to simulate. To address these challenges, a combination of methods was used, including projection pursuit multivariate transform, trend-residual decorrelation, pluri-Gaussian simulations, and turning-bands simulations. Various tools and applications were used to build the model, including in-house developed applications, Autovariogram software (Varify), and the RMSP python library. All computations were accomplished on the AWS cloud using the EC2-Batch service. The final set of simulations was validated using various methods, such as grade-tonnage curves, histograms, swath plots, and variogram reproductions, as well as validation using historical samples back-testing. The study highlights the importance of an automated, modular, and scalable framework in the development of conditional simulation workflows and describes the learning gained from trials of different combinations of methods and software

May 24, 2023

By M Zoorabadi, B Hebblewhite, S Saydam, W Timms

Based on the cubic law, the hydraulic aperture of rock discontinuities has the most significant effect on the hydraulic conductivity of jointed rocks. The hydraulic aperture of rock discontinuities is a stress-dependant parameter and reduces with increasing applied stress. Furthermore, the rock stress increases with increasing depth. Therefore, hydraulic aperture is a depth-dependant parameter. In this paper, new empirical equations are introduced to calculate the hydraulic aperture of rock discontinuities at different depths. These equations were developed on the basis of back analysis of compiled packer tests from different actual cases. They provide the capability to calculate range of variation and average hydraulic aperture when the orientation of discontinuity and field stress tensor are given. Furthermore, it is possible to calculate the hydraulic aperture of rock discontinuities when its value is given for another depth. A hydraulic aperture of 7.7?µm was calculated by this method, comparing well with a reported site value of 8.3?µm for rock discontinuities at the Stripa mine project at a depth of 385?m. These new equations can be used by analytical or numerical methods to estimate the hydraulic conductivity of jointed rocks.CITATION:Zoorabadi, M, Saydam, S, Timms, W and Hebblewhite, B, 2014. New empirical equations to estimate the hydraulic aperture of rock discontinuities at different depths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 375–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022

By M Boon, M Franklin

This paper outlines the journey of cultural maturation and management system development at the Mt Rawdon (MRO) gold mine from its acquisition by Evolution Mining Limited (Evolution) in late 2011 to 2016.Evolution embarked upon a series of projects that aimed to improve the operational consistency and implementation of change on-site, while leveraging off the existing strengths of the operation. This document describes the gaps that were identified, the processes used to close them, and the resulting cultural change and production outcomes, with a specific focus on how to optimise the culture at any mining operation.MRO had a history of four owners in less than three years when it became a key asset of Evolution. The site leadership team (SLT) decided to influence the culture at MRO by reviewing and upgrading the existing management processes.The first priority was to improve transparency and collaboration at the SLT level, followed by improving competency in project management. The next phase was to strengthen the internal communication using a deliberately designed network of meetings, communication screens and other initiatives. Once there was some traction, the focus moved toward increasing production volume and decreasing cost per unit by improving short-term planning and execution capability. Together with other initiatives, this resulted in improved collaboration between all functions, which in turn netted over 37 per cent mining production uplift.Following solid success, a process of prioritisation and alignment management was implemented. This supported the ‘Mine to Mill one operation’ ideal and allowed the SLT to decide month-by-month what actions were to be prioritised. These priorities incorporated production realities and longer term imperatives of the balanced business plan.Much of this work was completed during a period of declining gold prices and a relentlessly strong Australian dollar, making it difficult to justify spending money on improvement projects. This work proved critical for the operation’s long-term survival.CITATION:Boon, M and Franklin, M, 2016. Improving consistency of delivery at Mt Rawdon Operation, in Proceedings International Mine Management Conference, pp 305-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By M Sciortino, J Korczak, J Muinonen, A St-Jean

The Dumont deposit is a large (1179 Mt reserve), low-grade (0.27 per cent nickel) nickel sulfide project located in the Abitibi region 25 km west of Amos, Quebec. Royal Nickel Corporation (RNC) acquired the project in 2007 and has since taken the deposit through to feasibility. The disseminated nickel sulfide and alloy mineralisation is hosted within the serpentinised dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinised, ultramafic sill of komatiitic affinity. Pentlandite ((Ni,Fe)9S8), heazlewoodite (Ni3S2) and awaruite (Ni2.5Fe) are the dominant nickel-bearing metallic phases and can be recovered by conventional methods (flotation, magnetic separation). Non-recoverable nickel is also present within serpentine and olivine of the silicate matrix.A detailed mineralogical program including 1420 QEMSCAN« samples and 4400 electron microprobe points was undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. A total of 105 metallurgical tests have been performed under a standard procedure which have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block-by-block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance, thus unlocking the value of the Dumont deposit and other large tonnage low-grade ultramafic nickel deposits.CITATION:Sciortino, M, Muinonen, J, Korczak, J and St-Jean, A, 2013. Geometallurgical modelling of the Dumont Deposit, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 93-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J Gotte, C Morley, J Froud

Newcrest Mining LimitedÆs Telfer Mine is a world-class gold and copper producer, situated in the Great Sandy Desert, in the north west of Western Australia. The mine has a number of distinctive characteristics such as being one of AustraliaÆs most remote mine sites, being within 270 km of the hottest town in the southern hemisphere (Marble Bar) and having been shut down and reopened after a two-year feasibility study. The construction of a new plant and reopening of the mine gave Newcrest the opportunity to review their mining practices and systems including the opportunity to incorporate reconciliation as a core process. Telfer is now well on the way to being one of the largest gold and copper concentrate producers in Australia. When the mine reopened in June 2003, Telfer implemented SnowdenÆs Reconcilor software system to facilitate reconciliation of geological models, production data and plant measurements. The system was implemented on site in June 2004, as a web-based information management system, integrating other existing mining and plant software packages. It continues to provide an auditable process and consistency of data, providing ease of analysis with standard and customised reporting. This paper provides a case study of the reconciliation system implementation at Telfer. It outlines the consolidation of a number of management systems into one centralised system that can be used to compare and reconcile the tonnes and grades from the mine through to the mill. The authors outline the key estimates and measures that are used for reconciliation at Telfer, detailing the characteristics of the system used to capture the information and the benefits that have been gained through the use of a rigorous reconciliation process on a complex orebody.

Jan 1, 2007