Search Documents

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Mining Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost-has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this exceedingly interesting subject. In the working up of the electrical arrangements touched on in this paper, the author has had the able assistance of hisfriend Mr. F. J. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer isbetter than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant.Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of regulating factors before it is possible to arrive at a proper decision.

Jan 1, 1911

British Coal has made a practical progressive approach to improving the reliability of its mining equipment. Reliability must be addressed at the specification stage but does not end there and routine procedures are used to procure equipment of adequate reliability. The techniques used to monitor and improve reliability during the operational phase of the equipment, providing engineers and operators with detailed printouts, together with the types of maintenance employed, ensure high levels of availability. Finally, the methods of repair and overhaul of British Coal equipment and systems ensure that the initial reliability targets outlined on the specification, can still be achieved.

Jan 1, 1991

Designing for early access to deep orebodies is an essential driver for improved project payback. Vertical shaft sinking techniques have been developed to allow concurrent mine level excavation while continuing to sink. Project cash flows can also be improved when simultaneously deepening existing shafts beneath operating hoisting systems. Further economic advantage has been realised through creative sinking sequencing in twin ventilation/service shaft projects. A fourth technique to reduce project schedules involves partial shaft barrel equipping allowing unrestricted access to construct stations and continue with level installations. This approach reduces interference with barrel sinking activities to insignificant proportions. This paper reviews how these approaches have added significant value to actual shaft sinking projects, as assessed from a contractorÆs perspective, and discusses some of the practical issues to be addressed when planning future projects. Designers need to take cognisance throughout all project engineering phases of the adage that you are only sinking when cleaning the face. Cleaning can only be sustained when there is sufficient hoisting capacity.

Jan 1, 2005

By C Fricke, R Wood, P Velletri

"In a climate characterised by an ever increasing focus on cost reduction and maximising the utilisation of existing assets and infrastructure, understanding the uncertainty associated with alternative investment and operational choices becomes paramount to minimising the risk of making an ineffective decision. To assist in this process, TSG Consulting has developed an analytic framework to capture the underlying complexity of a mineral supply chain, and then quantify the impact of the uncertainty associated with the key drivers of business productivity. The technical basis of this approach follows three distinct steps: analyse the current system and identify the major factors that drive value build detailed models that can measure the response of the system to potential changes in the factors identified quantify the sensitivity of financial and capacity forecasts to these factors.Each of the above steps draws on a different area from the field of applied analytics, namely: data analytics dynamic modelling and designed experimentation meta-modelling and optimisation.Following the three-step approach described above ensures a rigorous modelling and analysis process is executed to support strategic mine planning decisions. The approach is equally applicable to the analysis of fully integrated system supply chains (pit-to-port), the evaluation of incremental capital investments to targeted areas of a supply chain, or when considering revisions to the operating philosophy of a system in the short term. The basis of each of the three analytic steps is explored in detail in this paper. The result is the definition of a structured mechanism for a business to actively manage risk and drive productivity as a component of the strategic mine planning process.CITATION:Fricke, C, Velletri, P and Wood, R, 2014. Enhancing risk management in strategic mine planning through uncertainty analysis, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By J G. Webster-Brown

The Tui Mine is located near Te Aroha at the base of the Coromandel Peninsula. It was a lead-zinc mine, which closed in 1973 due to declining concentrate prices, high overheads, and high mercury levels in the ore. The site was abandoned, leaving behind an acid rock drainage generating system, including a sulfide-rich tailings dam which has since caused pollution of Tui Stream, as well as open adits and waste piles which drain predominantly into the neighbouring Tunakohoia Stream. At the AusIMM conference in 2003, Harvey and Webster-Brown presented water quality results from the Tui mine site and lower stream catchments in 2002. In April 2006, Environment Waikato undertook remediation works to stabilise the dam and reduce acid drainage entering Tui Stream. In this study, water quality results from the Tui mine site and lower stream catchments are again being determined, in order to compare with the pre-remediation results. Preliminary data collected for summer indicate a minor but consistent improvement in water quality in the lower stream catchments, although lower Tui Stream continues to exceed ANZECC (2000) aquatic life guidelines for Cd, Cu, Pb and Zn. This slight improvement may be due to a decrease in the flow of ARD into Tui Stream, as there does not appear to have been an improvement in quality of the contributing ARD waters.

Jan 1, 2007

By A Dunne, R Kruger, H Coleman, P G. Laurens

External and internal challenges in mining are increasing the difficulty and complexity of operating mines. The external mining environment has a big impact on mining operations and is driving the focus on safety, sustainable mining, green issues, profitability and productivity. There is a very high emphasis on ‘reducing cost to improve’, lower mining and beneficiation costs by eliminating waste/inefficiencies (reduce people, use less consumables, multiskilling, etc). The internal mining environment is getting tougher to operate in, with the deposits being more difficult to mine, more difficult to manage due to external pressure along with issues associated with maintaining quality, etc.Technological and environmental developments too numerous to mention, mean that cost control models, reduction in human resource numbers, as well as other drastic measures to curtail expenditure and increase profitability have become part of everyday business. The capability to manage the mining environment in a systemic manner has been lacking and this increases the pressure for performance on those individuals operating and managing mines.Working smarter has become crucial to ensure that businesses optimise the use of their resources, become more safety conscious, more productive and remain cost-effective, while recognising the importance of sustainable mining now and in the future. The logic of determining and managing to the capability of the mining value chain will be examined and the underlying assumptions or beliefs guiding behaviour and decision-making will be highlighted.In order to identify the obstacles in the mining value chain that hinder achievement of its full potential, the following questions have to be asked:What are the factors that influence the performance of a mining value chain?What is the design capacity of the mine?How can the inherent flow and value capacity of a mine be determined?What types of solutions will allow a mine to operate at its inherent flow and value capacity?This article will discuss the way we plan, measure, assess and manage the mine value chain, by addressing the following factors:balanced capacity versus flow and value capacity designthe use of averagingoptimising individual components in a value chain versus optimising the whole value chain.Optimising flow and value through the mining value chain is one of the three pillars of Mineral Resource Throughput Management (MR™). MR™ is an entrenched and academically supported philosophy that has been successfully applied in the past decade in various mines throughout the world by EXXPLEO, a mining and beneficiation consulting company. EXXPLEO has partnered with HCL (a global IT company) to embed the MR™ philosophy, methodology and toolsets into a formal software product called Synchronised Digital Mining (SDM). The SDM system will provide mining companies with a sustainable platform to effectively apply the MR™ principles and toolsets effectively across all operations targeting increased productivity, efficiency and profitability without having to train operations and management staff into expert MR™ practitioners to successfully achieve the desired results.CITATION:Dunne, A, Laurens, P G, Kruger, R and Coleman, H, 2015. Optimising flow in the mining value chain, in Proceedings Iron Ore 2015, pp 437–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Scoble M, Peck J

This paper reviews the instrumentation and monitoring of blasthole drills and electric mining shovels at a surface coal mine in western Canada. The drill monitoring component involved the development and implementation of microprocessor-based hardware on Bucyrus-Erie 45R and 60R drills. Over a two year period 3800 metres of blasthole drilling were monitored The drill data was subsequently correlated with core and geophysical logs towards identifying unique and reproducible ranges of performance parameter data for the different rock types penetrated. Using this technique, the geology of the study area benches was characterized in detail. Once these same benches had been blasted, the performance of a P&H 2800XP shovel was monitored as it worked through the blasted ground. In this regard, the influence of different digging conditions on shovel performance were identified in a range of blast and geological environments within the study area. The precise nature of these environments was confirmed by a correlation with the interpreted drill monitored data and muckpile size distributions obtained from a digital photo-analysis study. The excavation of 500 000 bcm of waste was thus monitored and a digging index derived which reflected variations in muckpile diggability. The paper concludes by proposing an integrated monitoring approach which, as a first step, uses interpreted drill data for explosive loading. This capability would permit greater accuracy in explosives loading ie. charge placement within higher strength lithologies, while avoiding weaker units. The performance of an instrumented shovel would then be monitored as it works through the resulting muckpile. Interpretation of the shovel performance data would determine the overall quality of the blast in terms of a digging index (DI), providing an indication of the relative digging effort and the effectiveness of the blast design.

Jan 1, 1990

Drilling underground can be a hazardous undertaking in many circumstances. Raiseboring and boxhole boring underground could form an integral part of the block caving production methodology and getting the right mix of technical capability, ergonomics and economical viability has been the goal of many machine manufacturers. With the introduction of the Terratec Universal Boring Machine concept, flexibility of raiseboring, downreaming and boxholing has been enhanced by the introduction of a single machine that will perform all three processes. In addition to its technical flexibility, additional safety features have been introduced that will eliminate many sources of injury by mechanising most of the operational procedures. Together with the one-man remote operation, this machine design addresses and solves many of the safety issues. This paper outlines the machine concept, details its safety features and shows the techno-economic advantages for use in the block caving environment. Block caving is a distinct caving method applied mostly to large massive orebodies because of the inherent low costs and high production capabilities. Areas of sufficient size are mined by undercutting so that the mass above will cave naturally. Extraction of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling (Figure 1).

Jan 1, 2000

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

By A Finch, C Pridmore

The Cosmo Project falls within the Archaean to Palaeo-Proterozoic Pine Creek Orogen, one of the major mineral provinces of Australia.The Cosmo Deposit is interpreted to be a series of steep north-west-plunging gold mineralised vein, breccia and shear systems within the tight Howley Anticline and hosted within interbedded siltstones, mudstones, banded iron, phyllites, dolerite sills and greywacke.A folded environment poses a number of technical challenges, particularly for estimation.Handling of tightly folded and in some cases narrow domains might include subdomaining for orientation, omni-directional three-dimensional (3D) estimation within constrained domains or software-enabled unfolding/un-wrinkling procedures (transformation of the data and estimate space into a two-dimensional environment). Each technique has its own unique set of advantages and disadvantages.A further method (one applied at Cosmo) is where the estimation parameters (specifically search and variography orientation) are modified in a frequent or ‘dynamic’ sense to suit the orientation of the domain whilst maintaining 3D space. Control of the resource estimation orientation can be done in several ways, including the use of sectional panels of a specific size or, alternatively, orientation sector divisions. The sector approach provides some significant reductions in processing time over the panel technique and could be applied in a number of software packages.Three-dimensional ‘dynamic’ interpolation reconciles well with production data from Cosmo, whilst the sector method provides a practical technique that can be executed without the complications of transformation or the need for labour-intensive orientation subdomaining and with acceptable resource estimation run time.CITATION:Finch, A and Pridmore, C, 2014. Dynamic interpolation – estimation in a folded environment at the Cosmo Deposit, Northern Territory, Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Dunne

"Continuous improvement on metallurgical treatment plants is possible only when good data and analysis of the data are available. Good data implies appropriate and accurate mass measurement coupled with good sampling practices and accurate chemical analysis especially when carrying out monthly metallurgical metal reconciliations. Adequate characterisation of key samples (eg tailings, feed, concentrates and others) at timely intervals is an important part of a good continuous improvement program. The data from this will help identify opportunities to improve operation performance and thus profitability. Examples are provided of projects that have led to improved plant performance based on good metallurgical data collection and analysis.Citation:Dunne, R, 2016. Using Metallurgical Data to Drive Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Kent, R Paine

"Automated mining systems are increasingly being seen as a key requirement for a productive mining operation in the future. The importance of an integrated communication network infrastructure to support such systems is growing.This paper outlines the introduction of automated mining systems in large conventional mines as well as their growing role in block cave mines currently operating or being developed. The paper will then focus on a case study of how the communication infrastructure is fundamental to the operation of such systems and explain why the resultant communication networks require much more than just increased bandwidth (data capacity) to properly support the automation system within the overall mine operation.Mining operations already embarking down this road are discovering that the required network must be based on a true enterprise level architecture to not only enable the mine’s current plans for remote and automated mining, but also provide a scalable and integrated platform for future developments and requirements. The emerging issues for the communication network to truly support automation systems include: increased complexities of operating and maintaining multiple networks integration issues with disparate systems problems with reporting particularly as demands for corporate reporting and compatibility with enterprise systems become the norm ongoing management challenges, which will only increase with the proliferation of new technologies.The paper will explore how certain mining operations are addressing this by adopting a long-term strategy for automation deployment, which includes laying the necessary foundation architecture to meet their current requirements, while supporting their future visions for the fully automated mine.CITATION:Paine, R and Kent, D, 2014. Developing the foundation communication infrastructure to support remote and automated mining initiatives in underground mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 151–158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By D A. Sims

This paper outlines the contributing factors to a series of erroneous Mineral Resource estimates which led to considerable loss, including significant reduction of mine life and consequently a large write-down of asset value. The error prompted divestment of the mineral asset in the short-term by the owners, a major mining company. There were multiple and complex contributions to the result: • The mine was undergoing a transition in the deposit geology with increasing depth that was not accommodated in the models. Early indications of the geological transition in initial drilling were generally unrecognised in resource modelling. The shortcomings of the models became apparent with increasing infill drilling and subsequent production reconciliation. • There was a lack of recognition of, and confidence in, site-based input and skills by corporate technical management. The site had a reputation internally for over-delivery to plan early in its life and that supported the anticipation of ongoing metal delivery into the mine plan by management. • A corporate lack of confidence in site being able to adequately domain the mineralisation led to the use of a CIK domaining process, rather than one which was geologically based. This domaining process led to gross over-statement of mineralisation trends reflected in the subsequent OK estimate. • Timelines on the outsourced estimation process were so short that validation was not possible. Obvious errors in the estimate versus data were not able to be used to correct the issues and the site’s Competent Person sign-off occurred without adequate checks. This case study is presented to reinforce the concept that Mineral Resource estimates are not solely based on the ability of the Competent Person to satisfactorily guide the process. There are usually multiple complex issues in the estimation process which need to be recognised and considered in judging reconciliations of model to actual.

May 24, 2023

By A Trench, S Ulrich, S Hagemann

A synthesis of reported All-In Sustaining Costs (AISC) for 57 Australian gold mines in the period 2014–2016 reveals for the first time the clear influence of grade upon cost performance, most evident in gold-only underground mines. Past syntheses of costs on a single quarter basis have viewed grade as potentially subordinate to other factors such as production scale, mine geometry, mineralisation style and a combination of other mining-related costs. Better understanding of the grade to cost relationship on both an individual mine and whole-of-portfolio portfolio basis is needed. Insight into the roles and trade-offs between other cost-determining factors will aid the future sustainability of the gold mining sector in Australia and assist in targeting prospects for future resource growth and development. While the overall trend is toward higher-grade mines displaying lower costs and vice versa, the grade to cost functions appear radically different between mines based on time-series data. The median cost of Australian gold production in the final quarter of 2016 was A$1081/oz. The threshold for lowest cost quartile production was A$965/oz. Underground production now dominates Australian gold output – with 71 per cent of ounces originating from operations that are either entirely underground or hybrid pit/underground mines. Scale economies are evident, with smaller mines predominately among the higher cost producers. For mines of equal grade, open pit mines are lower cost than underground operations. Reserves are modest, with a median mine life for underground operations of 4.7 years based on current production rates. Reserve additions at mines are likely constrained not only by the finite nature of mineralisation at each mine but also by the geometrical difficulty of accessing suitable drilling locations to test for reserve extensions.CITATION:Ulrich, S, Trench, A and Hagemann, S, 2017. Towards an understanding of production costs at Australia’s underground gold mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By T Rohde, P Defferrard

In 2010 a store and release cover (the cover) was constructed on the south waste rock dump (SWRD) at Century mine. This also included aerial seeding of province native trees and shrub seeds. The purpose of the cover is to reduce percolation into the potentially acid-forming (PAF) waste rock by maintaining a compacted reduced permeability layer (RPL) at near-saturated conditions. This is achieved by overlaying the RPL with a 1.5 to 2 m thickness of soil-mulch. The soil-mulch has a hummocky final surface that captures rainfall, so it does not runoff, allowing it in part to infiltrate, with excess water removed by evaporation and transpiration. The RPL is the trafficked surface of the SWRD.The unsaturated behaviour of the cover is being monitored by instrumentation including volumetric water content and matric suction sensors and a weather station capable of estimating evapotranspiration. The instrumentation allows for direct measurement of infiltration into the cover, storage of rainfall, percolation through the base of the cover and in situ soil water characteristic curves (SWCC).The key functions used to describe the unsaturated behaviour of the cover materials is the SWCC and the unsaturated hydraulic conductivity function. The SWCC is a plot of soil water versus soil suction. It provides the loci of moisture states of a soil from the saturated to the dry state.The paper presents the results of five years of monitoring. It shows that total infiltration into the top of the SWRD was about 1.6 – 3.7% of cumulative rainfall over five years, with most of the infiltration going into storage within the cover. Runoff from the top of the dump is not allowed therefore, the remaining 95% of the total rainfall was lost to evaporation or as lateral flow when infiltration reached the RPL. The paper presents some simple analyses of the wetting by rainfall infiltration of the cover, leading to breakthrough at the base. Field data are used to support the analyses.Presentation of the SWRD water balance is also included in the paper using SVFLUX™GE which is a finite element model that simulates water transport through a saturated or unsaturated medium.CITATION:Defferrard, P and Rohde, T, 2018. Five years of cover performance monitoring and modelling for a store and release cover at Century Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 179–189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M G. Hawtin

The Rocklands copper project is a multilode, iron oxide copper gold (IOCG) + cobalt mineralised system located in the Eastern Fold Belt of the Mt Isa Inlier. Rocklands orebodies cover a range of oxidation zones from oxide, to supergene and primary. Each zone contains different economic minerals of interest. The supergene zones contain significant amounts of native copper and the primary zones are dominated by chalcopyrite. The juxtaposition of these oxidation zones and minerals make it an interesting mineralisation system.Current mine production sampling collects a nominal 3 kg drill chip sample from a 1 m composite, RC drilled interval. A site specific sampling procedure was needed to quantify introduced sampling error when taking grade control samples. Due to oxidation and mineralogical variation in ore zones we needed to develop a practically achievable sampling methodology that ensures minimum sample mass and sample error requirements are achieved to ensure ‘representative’ samples for all ore types.These issues are planned to be resolved using an experimentally derived method using principles from the Theory of Sampling. This method uses an experimental calibration of parameters K and a for Gy’s fundamental sampling error formula using a modified 32-piece sampling tree experiment to compile sampling nomograms for the primary and supergene ores. This paper demonstrates the process undertaken to improve the quality and standard of existing mine production sampling procedures at the Rocklands operation.Results indicate a sample mass of 5 kg for RC drill chips is appropriate for both the primary and supergene ores to achieve a fundamental error below 0.01 or 10 per cent relative error, which is slightly higher than the existing sampling protocol of 3 kg. An additional experiment is recommended to compile sampling nomograms using the exact laboratory comminution and mass reduction stage information to assess the use of a 3 kg sample. The results also indicate no changes are required to existing sampling protocols when sampling RC drill chips in primary and supergene ore at Rocklands.Sampling nomogram results also provide a useful ‘rule of thumb’ reference guide to other mining and exploration companies to help understand minimum sample mass requirements and sampling error during exploration drilling, resource evaluation and mining production stages when targeting similar IOCG mineralised systems. A sample mass of 5 kg is recommended when RC drilling similarly IOCG mineralised prospects and deposits in the Cloncurry area. Future test work is recommended when additional open cuts become active as well as including resource drilling drill core to provide better three-dimensional sample representivity.CITATION:Hawtin, M G, 2017. Minimum sample mass from reverse circulation grade control drilling at Rocklands copper project, in Proceedings Tenth International Mining Geology Conference 2017, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By D A. Sketchley

The Merlin Zone, a 2008 high-grade Mo-Re discovery, is a part of the Mount Dore Deposit in the Eastern Succession of the Mount Isa Inlier in Queensland, Australia. Hosted by carbonaceous metapelites and phyllites, the Merlin mineralisation comprises molybdenite veins, breccia infillings, stylolitic fracture fillings, and disseminations. Because rhenium is geochemically similar to molybdenum and commonly associated with it, global production of rhenium has been mostly a by-product of molybdenum refining. The high-grade rhenium in the Merlin Zone is an exciting discovery that is expected to become a direct source of rhenium. At the time of discovery, quality assurance (QA) procedures for rhenium were not in place at the Merlin Zone; therefore, they needed to be developed.The Merlin Zone was discovered using reverse circulation drilling, which led to concerns about molybdenite loss due to poor sample recovery. The twinning of the discovery hole with diamond core demonstrated a two-fold increase in molybdenum grade over several tens of metres. Consequently, the resources of the Merlin Zone were defined using assays from diamond drill core.Early analytical work, which was initially done only for molybdenum, comprised geochemical analysis with an aqua regia digestion, which have poor precision and can be biased low. Although initial testing for rhenium used similar procedures to those for molybdenum, a scarcity of commercial rhenium reference materials led to a validation process using neutron activation analyses and different digestions. This resulted in introduction of four-acid digestion assays, development of matrix-matched reference materials, and improvements to the quality of molybdenum and rhenium assays for reporting resources. Coarse and pulp duplicates were used to check for sampling bias and to ensure that levels of precision were adequate for the style of mineralisation and analytical methods. In addition, the direct and consistent geochemical correlation between molybdenum and rhenium provided another method for checking analyses.

Aug 22, 2011

By P F. Hodkiewicz

"Our understanding of mineral resources relies on three basic steps: data capture data interpretation model construction. Until recently, all three of these steps required significant time and manual effort to produce a single resource model for mine planning, typically taking more than a year to progress from drilling to the final block model. Over the past several years, BHP Billiton has been developing innovative workflows in rapid resource modelling projects to significantly reduce these time constraints and make the process more productive by replacing manual activities with automated ones. Rapid resource modelling is the process of combining recently developed off-the-shelf technology with internal technology developments to fundamentally change the way we collect, interpret, model and evaluate geoscience data. Initiatives include automated systems and standardised workflows to make it safer, faster and cheaper to continuously update multidiscipline resource models. Specifically, rapid resource modelling workflows combine: real-time analysis of drill holes and drill samples with downhole tools and hyperspectral scanning systemsautomated interpretation of drill hole intervals based on pattern-recognition algorithmscontinuous modelling workflows using implicit modelling software. This paper outlines technology developments and workflows that provide a more thorough understanding of mineral resources to support faster and more informed strategic, planning and production decisions.CITATION:Hodkiewicz, P F, 2014. Rapid resource modelling – a vision for faster and better mining decisions, in Proceedings Ninth International Mining Geology Conference 2014 , pp 183–188 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014