Search Documents

By J Ledgerwood

Namakwa Sands is a mineral processing company based on the West Coast of South Africa and is solely owned by Exxaro Resources Limited. Mineral ore is mined and processed, concentrated and both chemical and mechanically upgraded before being sent for electrostatic and magnetic separation units. The final high value mineral products report as Zircon, Rutile and Ilmenite.The recovery of non-magnetic material is largely dependent upon a number of factors, including but not limited to dew point, ambient temperature, feed rate, mineral size distribution, specific gravity and mineral content in head feed. One important limiting factor to recovery in typical dry mill operations is the particle size distribution of the feed. Variance in the particle size has catastrophic consequences for recovery. This is the reason for this study. Until recently large variances in non-magnetic production were viewed to be a function of machine operation. This view was later rejected with the feed size distribution determined as the major driver of low recoveries, for Namakwa Sands orebody 50 per cent variance in particle size distribution can be noticed within one day. This is because of the successive mining blending techniques employed.The predicament is that the two modes were so closely placed together that recovery of a single mode is almost impossible without the consequence of greatly reducing recovery. The second mode was found at 125 µm while the first was at 90 µm. Interestingly, for the mentioned feed type a cumulative size distribution of a unimodal feed type is almost exactly the same as for a bimodal size distribution. Thus a plot of cumulative size distribution will show no difference due to the modes being so close together. This is the reason why this phenomenon was not noticed before.The study also found that, using an high tension roll (HTR) or rare earth roll, a fine stream with a single mode at 90 µm versus a coarse stream with a single mode at 150 µm would yield completely different results interms of yields. Larger conductive particles are thrown from the roll while small particles loose charge faster (entrainment). Results in terms of the bimodal size distribution show that even though 25 per cent of the feed type is greater than 150 µm the yields followed a similar pattern to that of the coarse particles rather than that of the majority (75 per cent) fine particles. This confirms what was published by M Ziemski and P N Holtham in 2005 on charge decay rates; they mentioned that particle bed effects played a major role in recovery.

Oct 5, 2011

By A Esfahanipour, M Osanloo

Determination of cut-off grade?strategy is one of the most important stages of open pit mine planning and design. It is the parameter directly influencing the financial, technical, economic, legal, environmental, social and political issues in relation to mining operation. Choosing the optimum cut-off grade strategy that maximises the economic outcome has been a major topic of research workers for nearly one century. Many researchers have contributed in devising methods and algorithms, such as dynamic programming, linear programming, optimal control and so on for various aspects of its determination. In this paper, a non-linear mathematical programming for cut-off grade strategy optimisation is presented, considering the three main stages of mining operation introduced by K F Lane. In this model maximisation of net present value of mining operation, under the three constraints of mining stagesÆ capacities, considered as the optimisation criteria. Due to the discrete representation of the mining resource, the proposed non-linear formulation is approximated by a non-linear signomial geometric programming. According to non-convexity and the complexity of the proposed model, an augmented Lagrangian genetic algorithm was used to find the optimum cut-off grade strategy under varying and fixed price circumstances. To validate the proposed non-linear model efficiency, the results were compared with the results obtained by the K F Lane methodology. It was found that the proposed non-linear model works efficiently in the determination of cut-off grade strategy. According to the simplicity of the structure of non-linear programming modelling in comparison with dynamic programming it is hoped that, further development of this model would certainly provide the ability of considering managerial and technical flexibilities as well as incorporating more real mining conditions in the determination of cut-off grade strategy optimisation.

Sep 26, 2011

By N M. Player, R P. Varden, E Jones

"An effective geotechnical design provides an accurate and appropriate assessment, balanced with a mining company’s risk profile. Justifying the cost of slope assessment requires an understanding of the input sensitivities, and resultant risk, to achieve a slope of a required functionality. As a project progresses from Scoping to Feasibility, the geotechnical risk becomes better resolved through increased expenditure on drilling, testing, analysis and modelling as long as the input data is appropriately spatially distributed. Providing accurate and appropriate geotechnical assessments in the early stages provides confidence in all following stages, especially where initial analysis indicates difficult geotechnical conditions. It is also in the early stages of project definition that there is most opportunity to maximise the value of the deposit through investigations into optimal mining methods.This paper examines the advantages of geotechnical engineering input through a project study period. Early geotechnical involvement allows the Scoping and Pre-Feasibility Studies to be more effective. Operational risks can then be better understood and dealt within the Feasibility Study phase, also ensuring that the correct risks and management controls are put in place.With commodity price pressure and cost of resource recovery in a downturned industry, reducing the risk to cash flow, resource recovery and safety should be a primary goal for all mining companies. Reduced risk can be effectively achieved through geotechnical design of slopes to achieve a required performance as part of an integrated study to the Reserve definition and mine design.Citation:Varden, R P, Player, J R, Player, N M and Jones, E, 2016. Justifying Slope Design Risks and Costs, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 185–201 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By C Dick

Over the past three decades, mining operations have seen a significant increase in the use of contractors for mining, camp management and catering, recruitment, maintenance, power management, and commissioning. More recently contractors have been engaged for stores and logistics, OH&S, environmental, exploration, training etc. In some countries, such as South Africa, the trend is towards total outsourcing of all aspects of a mining operation which is coordinated by the owners’ management team.During the Global Financial Crisis (GFC) more Australian companies considered and/or took on this approach to recruiting for both projects and operations as mining companies were forced to rethink their corporate strategies as commodity prices plummeted to low levels, pushing operations and projects into potentially financially unviable territory.This paper discusses the labour recruitment, commissioning and operating strategy of Western Areas NL (WSA), with the assistance of Independent Metallurgical Operations Pty Ltd (IMO), as it progressed construction, commissioning and operation of the Cosmic Boy nickel concentrator at the Forrestania Nickel Project during and post GFC. The use of IMO contractors allowed Western Areas to mitigate labour cost risk during the uncertainty caused by the GFC and let their management team focus on the task of bringing a new operation into viable and profitable production.

Aug 8, 2011

As Pliny commented two millennia ago, The only certainty is that nothing is certain. Despite the many breakthroughs, advances and promises, the way we each live and work remains awash with technological, economic and political uncertainty. The resources sector is no exception in this regard. Mining itself is much more than a complicated process or recipe; it is a complex adaptive system. The way we adopt and adapt new technologies, the way we evolve data into corporate wisdom, the way we make decisions and even the way we view our concept of rationality should each be the subject of intense review. Translating these sentiments into sustainable company growth is indeed the challenge. This is unlikely to be achieved within convention, but through innovation. The game is changing!

May 1, 2010

Quite often the reserve assessor becomes enamored with the numbers gen- erated and forgets the basis for his assessment. The quality of the assess- ment can only be as good as the quality of the input data. The use of seismic data from the Gippsland Basin in assess- ing Esso/BHP's oil and gas reserves is an excellent example of this principle. By significantly improving the quality of seismic data, a much more reliable estimate of a field's reserve potential can be made. In addition, it provides the basis for further delineation drill- ing which, as recent experience in Gippsland has shown, often leads to increased reserves.

Jan 1, 1979

By Baafi EY, Chatterjee PK

The quality of mine planning decisions ultimately depends on reliable estimates of the characteristics of the orebody. The quant- ifiable factors such as grades or thickness can be estimated from field data gathered from outcrops or exploratory drillholes. Since outcrop data is necessarily limited to the periphery of a deposit, extensive drilling generally is required. This paper outlines a method for selecting the number and location of additional exploratory boreholes using an iterative procedure based on a mathematical optimization concept called fixed point theory. The method is illustrated through its application to an exploratory drilling program for a coal mine where optimized locations gave a lower estimate of regional and block variances than a manual Choice.

Jan 1, 1986

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

An integrated mining equipment development organisation is typified by Deutsche Montsn Technologic of Essen, Germany. working on improvements in reliability, production and control in coal mines. Examples of recent mining advances are in mechanised roadheading, in different approaches to cutting technology, and in low height roof bolting.On the longwall face the mechanics of cutting are related to supplied energy as well as to dust make. In conveying both armoured face conveyors and conveyor belts are monitored. Roof support is not neglected and the continuous pumping of stowage slurries provides further options for longwall support. Surveying developments, particularly the gyro-theodolite, directional drilling. and shaft vehicle monitoring provide further examples of advances in control in coal mining activities.

Jan 1, 1991

By K Rau

The overall success of a mining operation is directly impacted by the reliability and availability of mining equipment. Heavy-duty vehicles such as excavators and haul trucks are used for conveying of bulk material and improving such assets’ availability helps reduce costs, increase throughputs and improve safety (Ravande, 2022). If a mining operation’s key performance indicators (KPIs) are tied to operational performance, then overall equipment effectiveness (OEE) is an essential metric to track progress and to identify areas of improvement.

Sep 1, 2024

By G McKay, M Erskine, S Macklin

The City of Sydney is currently investing in a number of infrastructure projects that require tunnel excavations within the Triassic Hawkesbury Sandstone. It is generally accepted that this formation has high residual stresses of ‘tectonic’ origin, so much so that these stresses have been implicated in a number of well-known failures and problems for tunnelling. These include failure of ‘roof beams’ comprising discrete beds in the crown of tunnel excavations; stress-induced spalling and ‘slabbing’ of tunnel walls; shear displacement between beds causing the failure of rock bolts; strain in adjacent infrastructure and, the necessity for re-grouting of high conductivity fractures due to stress relief dilation after excavation. Whilst there is an extensive published database of in situ stress measurements comprising ‘hydrofrac’, ‘over-coring’ and ‘slotter’ stress measurements, these data indicate a considerable spread of results. The traditional approach to interpreting this data has been to attempt to fit linear correlations to stress versus depth data, based on personal experience and ‘back-analysis’ of monitoring data during construction. However, there are a number of such correlations in the literature and there is divergence of opinion regarding the assessment of ‘background’ in situ stress and appropriate upper and lower bound values for design. This paper provides a brief review of the published data; suggestions on an alternative ‘risk-based approach’ to assigning in situ stresses for design; and, proposals on how in situ stress tests may be conducted in future to improve the quality of the database available to designers.CITATION:Macklin, S, McKay, G and Erskine, M, 2014. A review of the in situ stress database for tunnel design in the Hawkesbury Sandstone, Sydney, New South Wales, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 171–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Lyman GJ

Systems for the routine on-line determination of ash content of process streams in coal preparation plants and handling systems have been in use in Australia for over four years. More recently, monitors for on-line moisture measurement have been developed to complement the ash measurement function. The technology for these systems is reviewed briefly. The development of reliable ash and moisture monitors has made the implementation of automatic systems of coal quality control practical. The emerging philosophies of automatic control in Australian preparation plants are examined with particular emphasis on systems involving dense medium circuit regulation. Related developments in flotation control and coal sorting are noted to complete this overview.

Jan 1, 1987

By Hustwick I

New Zealand Steel Mining Limited operates two independent sand mining operations on the West Coast of the North Island of New Zealand. (Fig. 1)Waikato North Head 30km south of Auckland supplies ironsand concentrate as the raw feed for New Zealand Steel's works at Glenbrook, and Taharoa 70km further south, exports ironsand concentrate to Japan. Taharoa uses two sets of six low pressure Warman centrifugal pumps in series to load bulk ore carriers 3km off shore through two underwater pipelines.Waikato North Head delivers the ironsand to Glenbrook l8kms through a 200mm ID buried pipeline using two stages of high pressure positive displacement (HPPD) pumping.A high level of operating and maintenance expertise has been developed since commissioning the two systems which are proving to be reliable, efficient and of minimal impact environmentally.

Jan 1, 1990

By Falconer A. J

Two magnetic parameters are proposed as a basis for the assessment of ironsands beneficiation. The parameters are deter- mined for raw sand prior to dredging and for magnetic separator head feed over a production period of five months. The relationships between these parameters and the performance of the magnetic separators are examined to establish the value of magnetic assessment compared with the traditional soluble iron assay method. The results illustrate that the first parameter, true magnetic fraction (TMF), has a value superior to that of soluble iron when relating raw sand grade calculated by tri- angulation to magnet performance. In terms of the relationship between magnet head feed grade and magnet performance, TMF and soluble iron perform equally as assessment parameters. For the ironsands mined during the five month period, the second magnetic assessment parameter, composite fraction (CR), is shown to merely reflect TMF and offers no additional information for assess- Ment. Conclusions are that true magnetic fraction has many advantages over soluble iron in terms of time and cost of determination and that it is a meaningful and reliable parameter upon which to base all calculations relating to the mining and beneficiation of ironsands.

Jan 1, 1980

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

By Bukovinsky SB

The smelting, refining and hydrometallurgical operations practised in the winning of non-ferrous metals are associated with severe aqueous and high temperature corrosion problems.With the increasing costs of maintenenace and the utilization of computerization to control the processes, the trend in recent years has been to spend more capital on improved and proprietory grades of engineering materials, which offer greater reliability and more cost effective plant performance.The problems which have plagued stainless steel users for many years are the alloys' poor performance in chloride or other halide media where pitting, crevice or chloride induced stress corrosion cracking may occur, have been essentially solved by the new proprietory grades. The controlled additions of minor alloying elements including rare earth metals have led to the development of stainless steels with high mechanical strengths, improved corrosion resistance, and high temperature corrosion resistance and structural stability.

Jan 1, 1985

By A Garvie, D Kentwell, J Chapman

"Most new mining projects require an initial assessment of the locations and volumes of potential acid forming (PAF) waste that is likely to be moved and dumped in surface waste stockpiles. This requires sampling of the waste rock zones and submitting the samples for a series of tests. Key to the outcome of the waste characterisation process is obtaining sufficient samples that are representative of the various rock types both in number and spatial distribution.Various regulatory bodies throughout Australia and the rest of the world are currently struggling with how to define minimum amounts of sampling to achieve realistic estimates without imposing excessive costs and time constraints on a project.This paper addresses two aspects of the process: what constitutes a æsufficientÆ number of samples how to use those samples in determining volumes of likely PAF material.Geostatistical methods of characterising orebodies with large numbers of samples are routinely used in the mining industry by geologists and geostatisticians to estimate and classify Mineral Resources. In theory exactly the same methods can be used to estimate PAF waste locations and volumes.In practice the number and spatial distribution of dedicated PAF waste samples at feasibility stage is typically so small that it is almost impossible to estimate the spatial distribution of PAF material with any degree of confidence at all. Consequently, the common approach is to characterise a few samples from a lithological unit and then assume that they represent the unit as a whole. This approach, however, can be fraught with risk.This paper describes some of the findings of SRKÆs evaluation of several coal projects with respect to PAF waste evaluation and highlights some common misconceptions held by people working in this area that do not have a knowledge of statistics or geostatistics.CITATION:Kentwell, D, Garvie, A and Chapman, J, 2012. Adequacy of sampling and volume estimation for premining potential acid forming waste evaluation using statistical and geostatistical methods, in Proceedings Life-of-Mine 2012, pp 79-88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983

By B Mil, D P. Adhikary, M S. Craig, P Rutzou

As shallow coal reserves with easier mining conditions are exhausted, future deep coal mining with difficult mining conditions may face significant economic, technical and environmental challenges. Moreover, due to increased coal production capacity with the new generation longwall systems, predicting adverse mining conditions has become more important than ever before. The potential impact of these difficult conditions is an increase in mining risks and costs. Reliable prediction of rock mass deformation, mine stability and mine water inflow is not only essential for improving mine safety and reduction of coal production costs, but it is also important for the assessment and management of the environmental impact of mining. This paper briefly describes an integrated approach to mine groundwater simulation and prediction. Central to this integrated approach is a three-dimensional computer code called COSFLOW, developed by CSIRO of Australia in collaboration with NEDO and JCOAL of Japan to address the pressing issues of mine water management. COSFLOW incorporates unique features that make it ideal for the simulation of coal mining and examining the interaction between rock fracture, aquifer interference and water flow. This paper also presents an example of an application of the integrated approach and COSFLOW in water inflow prediction at Springvale Mine in New South Wales.

Jan 1, 2006

By Fabjanczyk M. W

A limitation to present theoretical roof reinforcement design methods is the inability to derive accurate and quantitative information about the roof rock condition and the action of reinforcement at various excavation stages. To obtain the information required to assess roof rock stability, detailed monitoring of the in-situ behaviour of reinforcement and roof strata is required. Reliable instru- mentation and techniques have been developed for use in underground coal mines to identify the geometry and magnitude of displacements occurring in roof rock and the forces generated in reinforcement. The use of such instrumentation allows an accurate assessment of the in-situ capability of reinforcement and the mode of reinforcing action developed. In-situ monitoring can supply data required for the practical design of reinforce- ment and assess the potential stability of current designs. The use of such data together with mine wide appraisal of rock and stressfield considerations, can allow roof reinforcement to be designed on the basis of a predicted roof Response.

Jan 1, 1986