Search Documents

New Zealand depends on foreign investment for economic development. This also applies to the development of New Zealand's mineral resources. For this foreign investment to happen there must be some incentives to attract the investment. While prospectivity is the dominant parameter considered by investors it is not a variable that can be changed, only the perception of New Zealand's prospectivity. Other parameters likely to be considered are sovereign risk, red tape, green tape, land access, civil unrest, land claims, social risk, labour relations, infrastructure and natural disasters. Regulators and political will can vary some of these parameters. Where New Zealand fits internationally can be measured by investors' perceptions of these parameters. Following on from these perceptions New Zealand can be seen to have advantages in some areas and be disadvantaged in others. How to deal with the disadvantages to give investors confidence is not easy in the New Zealand environment where the development of mineral resources plays a small part in an economy dominated by agriculture. Added to this is the current global state of the minerals industry which offers even more of a challenge to attract foreign investment to develop New Zealand's mineral resources.

Jan 1, 2000

By J Gresham, A Turichshev

Ore from Henderson’s 7700 Southwest panel cave is transported between the production and truck haulage levels through a series of orepasses. A typical orepass complex consolidates dump points from four production drifts into two long bored raises feeding into a single truckloading chute. The system typically covers a vertical extent of 200 m and a lateral extent of 90 m. In the process of commissioning several initial orepass complexes, challenges with preferential draw in the long bored raises were observed. Preferential draw occurs when one long orepass mobilises much sooner and/or flows significantly faster than the other orepass. This has negative implications for orepass availability in the production drifts. As future mining at Henderson relies on the construction and use of such orepass systems, the development of appropriate design criteria and practical solutions to existing flow problems was necessary.A series of PFC3D numerical models were developed to assist in identifying the factors influencing preferential draw and possible corrective measures. The models helped to identify two primary factors that caused the preferential effect: the relative elevation of the brow at the bottom of each long bored raise, and the location of the bin used to funnel fragmented rock from both raises into the chute. This paper covers the initial design of the orepass complexes at Henderson, results of the numerical models, mitigation work done to date on existing orepass complexes, and design criteria for future construction.CITATION:Gresham, J and Turichshev, A, 2016. Correcting preferential flow problems in long orepass systems at Henderson Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A Mechanistic Model of Batch Grinding in Ball Mills

Sep 13, 2010

Beneficiation of Iron Ore - Washing with Surface-Active Agent The stability of the dispersed phase in 10 wt per cent slurry of iron ore slime and fines was studied at pH 5 and different concentrations of surface-active agents. The behaviour of the dispersed phase of iron ore slime and fines is different for different surface-active agents. The improvement of iron value of slime and fines in the presence of surface-active agent is best realized at pH 8, where the Al2O3/Fe and Al2O3/SiO2 ratios in the concentrates are appreciably reduced. The polar functional group like -COO- interacts with hematite surfaces and forms outer- and inner-sphere surface complexes depending on the suspension pH and adsorbate.

Sep 13, 2010

Detrital gold in the Greymouth-Hokitika area has been won from: (a) gravel of the Pliocene Old Man Group, (b) glacial outwash gravel of Middle and Late Quaternary age, (c) raised shoreline deposits of Middle and Late Quaternary age, (d) deposits resulting from the erosion of (a) to (c). The source of the gold was probably widely dispersed quartz veins in great thicknesses of greywacke and low-grade schist eroded from east of the Alpine Fault, with a contribution from veins in Greenland Group greywacke in the south. At times of high interglacial and post-glacial sea level, gold was concentrated along marine shorelines, and subsequent progressive uplift has resulted in a set of sub-parallel beach leads up to 100 m above present sea level. During glaciations, gold was concentrated in outwash streams close to moraines, especially where ice forming one moraine penetrated and destroyed an older one. Worked deposits in the Old Man Group may also be associated with glaciation. Apart from workings that are essentially extensions of past workings, significant new prospects may depend on inferences as to where prospective deposits are completely obscured by younger ones.

Jan 1, 1996

OneSteel and BlueScope Steel have been working with the CSIRO to develop sustainable carbon fuels and reductants which are suitable for use in the iron and steel industry. One of the initial focuses of this work has been a process called steel recarburisation which is the addition of carbon to liquid steel to produce particular steel grades. This paper reports on the preliminary work and the recent full scale recarburisation plant trials conducted at the OneSteel Sydney Steel Mill.   Preliminary experimental work involved kilogram scale recarburisation of liquid steel with a range of commercial and prepared charcoal products. This work showed that charcoal dissolves into liquid steel very quickly and that carbon recovery to steel was inversely related to the charcoal volatile content. Initial larger scale work focused on the collection of wood, and preparation of low volatile charcoal which is required for steel recarburisation. Approximately three tonnes of charcoal was prepared at the Corrimal coke ovens of the Illawarra Coke Company. This charcoal was dried, crushed, sized and packaged in a form suitable for addition to 80 tonne liquid steel ladles.   The recarburisation trial was conducted over 30 ladle heats during June 2009. The charcoal was manually added to the liquid steel in 5 kg bags using normal plant practice. Conventional commercial recarburiser was also added to the liquid steel in alternate ladle heats. The performance of the charcoal was compared with the conventional recarburiser based on the carbon recovery to steel, hydrogen pick-up by steel and the rate of carbon dissolution into steel.   An analysis of the trial results showed that the charcoal performed at least as well as commercial recarburiser in carbon recovery and rate of dissolution but may have resulted in a slightly higher hydrogen content of steel. This is probably due to the higher moisture content of charcoal. The main challenges in the future include: increasing the charcoal density to improve transport and handling economics, securing a sustainable supply of biomass for the steel industry and developing a charcoal production industry so materials of suitable quality for both production and trials on other applications can be conducted.

Jun 1, 2010

The paper considers Aboriginal responses to large-scale mining, including Indigenous attitudes towards land access for exploration and project development. The core question, in which I have been interested for some time (Trigger 1997a; 2000; 2001), is: what are the significant factors affecting responses among Indigenous communities to mining exploration and development project proposals?

Jan 1, 2002

Bioleaching of Weathered Saprolite - Heavy Metal Adaptation Mechanisms of Aspergillus foetidus Nickel laterite ores remain important to the future supply of Ni and Co as they contain the bulk of known nickel and cobalt reserves (80 per cent and 90 - 95 per cent respectively). Current commercial extractions of Ni and Co from nickel laterite ores are energy intensive and operational costs are high. Microbial leaching of oxide ores has the potential to offer a much needed step-change in the technology for processing laterite ores. Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. Optimisation of the process in in-situ application, however, has been hampered by the toxicity of the heavy metals that are being leached by the organisms. Our recent study has shown that organisms are able to develop tolerance towards heavy metals by adaptation. This study examined the extracellular metal detoxification mechanisms of A. foetidus in 0.2 per cent (wt/v) to 0.7 per cent (wt/v) of weathered saprolite ore. To support our analysis, FTIR, CHNS and microscopy were used to confirm the participation of specific functional groups in the extracellular detoxification process.

Sep 13, 2010

By P Meehan, R McAree, Z Guan

Equipment maintenance is 30 - 50 per cent of the operating costs for a typical mining company. While this is substantial, its importance is beyond its significance as a cost heading. Modern mining requires large amounts of investment in capital infrastructure and equipment to produce a product sold at a low unit cost. To stay competitive, such a business has to focus on full realisation of its capital investment, ie sustained production at high levels. Maintenance plays an essential role in achieving this goal. Mining companies typically use a mix of breakdown or corrective maintenance, planned maintenance, and some condition-based maintenance. The share of breakdown maintenance has been coming down through more effective planned maintenance and better condition monitoring tools. Planned or preventive maintenance (PM) is playing an increasingly important role in todayÆs mining maintenance. This is the suite of inspection and repair/replacement actions performed at scheduled time intervals as part of a preplanned activity. The activities are scheduled well in advance and, usually, the current wear-state of the machine is irrelevant. For example, the replacement of a major gear may have been planned 18 months in advance; replacement is carried out when the time comes regardless of the actual condition of the gear. The PM costs are significant and include direct cost of parts and labour as well as the opportunity cost of lost production while the machine is under maintenance. It is important to identify the optimum PM effort because over-maintenance should be avoided as much as under-maintenance. A new concept called severity-based maintenance is introduced in this paper. We have seen that measuring equipment ageing in mining merely by counting the engine hours is a very imprecise way of planning and scheduling maintenance because the damage accumulated in one hour varies enormously from operator to operator and with changing pit conditions. We recommend continuous monitoring of duty on all major equipment. This is feasible without having to fit out the machine with an army of sensors because most of the physical sensors required by dutymeters are already installed and maintained as part of the existing performance monitors. While the investment is modest, the potential benefits are huge and can be grouped under three headings:Immediate benefits will come from providing operators with direct feedback on the effect of their behaviour on machine health and training them to use this feedback to correct their operating style. The equipment can operate closer to the limits of capacity, producing more without unduly sacrificing the availability by monitoring and controlling the severity of the operation, ie the duty on the machine. Longer term benefits accrue from establishing correlations between actual time to failure data and measured equipment duty and using these correlations to optimise maintenance effort as well as planning new equipment purchases and warranty conditions.

Jan 1, 2002

A variety of cement raw materials occur within the Cenozoic sequence in Northland. These form the basis of Golden Bay Cement's cement manufacturing operation at Portland, Whangarei. High grade limestone is taken from the Whangarei Limestone formation, which has been shown to have been sub-aerially weathered and developed mature karst features prior to deposition of the overlying allochthon sediments. In this instance, remobilisation of allochthon sediments following uplift and erosion is inferred. At Portland Quarry, argillaceous limestone is extracted from deformed thrust sheets in the allochthon sequence. Quarry operations have been designed to handle the steep asymmetric folds, thrust faults and fracture zones that affect the resource.

Jan 1, 1999

By D E. Gadd

Since October 1972, New Zealand Steel Mining Ltd has loaded around ten million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110 000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the ship loading system and attempts to answer the question: 'If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?'

Jan 1, 1980

By S Speed, N Corlis, A Goldstone, G N. Browne, M Fitzpatrick

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. A non-notified resource consent was sought which necessitated that environmental effects be shown to be æless than minorÆ, and resulted from robust science and a pragmatic approach to design. As part of the assessment of environmental effects, there was a need to understand the effects of boron concentrations on aquatic organisms (ie algae, plankton, plants and invertebrates) in the receiving environment. Boron is a naturally occurring element that is found in the form of borates in the oceans, sedimentary rocks, coal, shale, and in some soils but Waikato coals and ashes have particularly high boron content. Boron is an essential micronutrient for higher plants with interspecies differences in the levels required for optimum growth. As aspects of the ANZECC (2000) derived boron limits are based on toxicity of aquatic algae and plants to boron it was important to assess these components in the environment. The effects on the receiving environment of the Awaroa Stream were assessed using predicted water chemistry and comparing actual boron concentrations in a comprehensive and multifaceted reference-condition approach of catchment ecological indicators. In addition a toxicological-based assessment of boron and a re-calculation of the ANZECC trigger levels were undertaken and applied to the ecological indicators. The reference-condition approach revealed that habitat and overall water quality attributes at and between sites was more influential in determining the aquatic biotic communities than boron concentrations alone. There was no evidence of any gradient of changes in ecological indicators with changing boron concentrations, nor evidence of any residual effect of high historic boron concentrations on the aquatic biota.

Jan 1, 2006

By G H. Clark

Batu Hijau is a porphyry copper-gold deposit located onSumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54 000 m of drilling in 105 diamond drill holes over a surface area of 1.2 km2 and to a depth of 1000 m below surface (412 m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55 g/t Au (variable cut-off) from an open pit in the higher grade portion of the resource.   The deposit is associated with a calc-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200 m diameter at surface to 500 m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbledykes or postmineralisation intrusive rocks.   Hydrothermal alteration of Old Tonalite and adjacent rocks is centred on the Old Tonalite and is zoned from a core of pervasive potassic alteration grading to an outer propylitic halo. At depth a propylitic assemblage is developed in the low grade core in the Old Tonalite. Phyllic alteration, late stage and mainly fracture controlled, overprints both potassic and inner propylytic zones. Intermediate argillic alteration overprinting is widespread, particularly on the eastern side of the hydrothermal system, where advanced argillic alteration overlies argillic alteration.   Ore grade mineralisation is cylindrical in shape, up to 800 m in diameter, and is centred on the Old Tonalite. A high grade shell (>0.75% Cu) forms an upward tapering cone in and around the Old Tonalite and reaches the surface in the centre of the deposit. Lower in the shell >l g/t Au and >2 g/t Ag accompany >1% Cu. Below 75 m above sea level mineralisation in the Old Tonalite rapidly decreases as a weakly mineralised core develops, but the limb continues to contain mineralisation to at least 412 m below sea level. Fracture and vein-controlled chalcopyrite and bornite are the dominant hypogene copper minerals and are the hosts for most of the gold mineralisation. Gold occurs free and in the lattice of the copper sulphides, and has been observed in quartz.   Weathering, especially where argillic alteration is developed, has produced a strongly leached cap, up to 147 m thick, below which is an irregular copper enriched supergene zone. Where leaching is not developed, such as over the centre of the deposit, an irregular oxide zone and a weakly developed supergene zone may be present.

Jan 1, 1995

Removal of Dilute Toxic Anions in Wastewater Using Aluminum Hydroxides Co-Precipitation Method

Sep 13, 2010

By C E. J de Ronde, J L. Mauk

Sulfide chimney samples collected during the 1998 - 1999 R/V Atlantis û DSV Alvin 3 - 30 research cruise have been examined and classified into four types, based on common characteristics. Chimney morphology is the most important characteristic and resulted in the following groups: 1. flutes, 2. cones, 3. wide-flats, and 4. beehives. Other characteristics resulted in the classification of subgroups within the flute, cone and wide-flat groups. The combination of characteristics, including; the presence of an orifice, internal chimney fabrics, wall thickness, extent of weathering, and the presence of Alvinella worm casts, enable evolutionary trends between the different chimneys types to be established. These trends indicate that with time, flutes evolve from immature zoned chimneys with a central orifice and smooth thin-walls, into cone chimneys with thick walls and massive fabrics which have their orifices infilled by massive sulfides, and a rough exterior. Repeated mineralisation within, cones may result in the formation of wide-flat chimneys. Beehive chimneys can form at any time during chimney growth.

Jan 1, 2003

By W T. Yen

Pyrrhotite crystallises as either a hexagonal or monoclinic structure, both of which can occur in ore deposits. In general, pyrrhotite is not considered as a valuable mineral unless it contains considerable amounts of other metals like nickel or copper. In fact it causes numerous problems in flotation including intensive oxygen consumption, which results in poor selectivity among sulphide minerals in the processing of complex sulphide ores. Also, because of its high sulphur content, pyrrhotite is a major contributor to environmentally detrimental sulphur dioxide (SO2) emissions from smelters. Pyrrhotite also interacts galvanically with grinding media via electrolyte species present in the flotation pulp, resulting in media corrosion. The most effective way to reject pyrrhotite is through a separation stage, which may be difficult when both types of pyrrhotite are present in the ore. In this regard depression of pyrrhotite through a flotation stage may be applied. Pyrrhotite depression by either intensive oxidation or by using sodium cyanide has been practiced. Results present in this work show that NaCN can depress pyrrhotite effectively when combined with an alkaline environment and low collector concentrations.

Jan 1, 2002

In the context of sustainable development, the Minerals Council of Australia (2010) states that 'investments in minerals projects should be financially profitable, technically appropriate, environmentally sound and socially responsible'. In other words, the business of mining can only be sustained if these criteria are met.   Science and technology plays a major role in all four of these criteria. This paper will present the technology and innovation emerging from the Minerals Down Under National Research Flagship which brings together CSIRO and more than ten of Australia's leading universities to work with industry to drive efficiency, productivity and environmental performance. This work is required if the Australian minerals sector is to thrive and continue to deliver national benefit in the face of increased global competition, declining ore grades, depleting ore deposits, increasingly constrained national resources (land, energy, water and people) and changing societal expectations.   Science and technology to reduce emissions and water use, discover greenfields resources, enable deeper mining operations and transform mineral processing are described. Technology is presented as an enabler of sustainability: a means to this end but not as an end in its own right.

Jun 1, 2010

Python Underground Processing Plant Critical Design The use of continuous gravity recovery in combination with a controlled breakage fine crushing and screening system followed by flash flotation has been incorporated into the Python processing plant. This provides miners with a flexible, robust, low cost, low energy pre-concentration process for the recovery of gold and/or heavy minerals. The Python plant incorporates fine crushing utilizing either High Pressure Grinding Rolls or Vertical Shaft Impactors in combination with the InLine Pressure Jig and Flash Flotation to continuously liberate and recover the valuable minerals. The use of these technologies has enabled a narrow, transportable pre-concentration plant to be produced which can easily be installed and operated in underground drifts and tunnels.

Sep 13, 2010

The Ekati Diamond Mine is located on permafrost terrain in CanadaÆs Northwest Territories. The mine rock consists of: diamond-bearing and barren kimberlite; and surrounding waste rock such as granite. The kimberlite occurs in several vertical æpipesÆ that are, or will be, mined using open pits. Early predictions of drainage chemistry at Ekati identified the potential for ARD due to sulfide oxidation from both waste rock and kimberlite. This was surprising for the kimberlite, because neutralisation potentials (NP) are typically hundreds of kg CaCO3 equivalent/t. However, subsequent testwork showed that substantial portions of the NP ædisappearedÆ quickly, apparently due to the unusual non-carbonate mineralogy. In any case, additional predictive work concluded much of the rock was benign and there would be no ARD. Shortly after mining started, ARD appeared from both the waste rock and kimberlite, although a few years passed before the company and its consultants recognised that at least some of the acidic water was ARD. Numerous other processes have been put forward as possible explanations for the remaining acidic drainage, although none have been either confirmed or eliminated. Because: the causes of the ARD and acidity are not known; no causes have been eliminated and more have been added; drainage chemistry was not predicted accurately; and future mining will encounter similar rock. I believe the Ekati Diamond Mine needs high-level assistance to understand current chemistry and to avoid problems with future drainage. Organisations like INAP, MEND3, and universities could provide this assistance.

Jan 1, 2003

By W Blair, J Bosman

The measurement of ferrosilicon rheology and characterisation of the parameters that have a direct influence on medium rheology provide the basis for evaluating, comparing and selecting an appropriate size and shape of medium to maximise separation efficiency in a dense medium application. The role of medium viscosity on particle separation in both static and dynamic separators is illustrated using relevant theory. The primary measurements of rheology are medium viscosity and stability. These in turn are determined by particle size, particle density and particle shape which in turn can be quantified. Additional characterisation parameters are also discussed. Different areas of application where ferrosilicon characterisation can be used are also discussed.CITATION:Bosman, J and Blair, W, 2017. The practical characterisation of ferrosilicon for dense medium applications, in Proceedings Iron Ore 2017, pp 135–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017