Search Documents

By R. S. Archer

THE PROPER representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem. The complete solution of the problem will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the A1 point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A 1 point is an open question, but that complete graphitization (to less than 0.10 per cent. combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440° F. It is the

Jan 2, 1920

By Robert Henry Bradford

This investigation was undertaken at the suggestion of Prof. Henry M. Howe, of the Department of Metallurgy, Columbia University, who, in a letter to the author, dated October 23, 1900, wrote as follows, suggesting the subject of this dissertation : "The extraction of silver from copper mattes by either the Ziervogel or the Augustin process depends upon converting the silver into silver sulphate by means of the sulphuric anhydride evolved from the decomposition of ferrous sulphate and cupric sulphate, which are formed during the roasting operation itself from the iron and copper sulphides present. "It occurred to me, some time prior to the autumn of 1897, that these processes might be made much easier by adding to them, at the proper stage, ferrous or cupric sulphate, or both, in the form of green or blue vitriol. That is, instead of having to rely solely on our ability to generate these sulphates in this very delicate roasting operation, my idea was that we could add a small quantity of already-prepared sulphate at the proper state of roasting, viz., at or before the period when the solphatizing of the silver occurs. The comprehensive audit of the accounts of a mining company is extremely important in its relations to the legal situation and obligations of the corporation, the personal liability of the directors, and the interests of the investing public. A consideration of the subject as affecting the professional duties and fixing the responsibility of a mining engineer engaged in the expert examination of a mine or in charge of mining operations, is equally important, though this phase of the question is not often presented systematically.

Jan 1, 1903

By C. W. Covington, H. C. Cook, J. F. Libsch

Sputtered aluminum thin films were prepared in each of two conventional bell-jar vacuum systems. One system utilized an inner "getter sputtering" enclosure; the second system was a standard diode sputterirlg arrangement. Consistent and repeatable film properties were obtained in both systems provided sufficient cleanup and presputter time was allowed. The various problems associated with aluminum sputtering are discussed, with pavticular attention to the vzinimization of film contamination by outgassing and oxidation. The growth and structure of the aluminum thin films were studied with the aid of electron wzicroscopy and related to deposition rate, substrate temperature, and film thickness. The resistivity of the films was correlated to film structure and surface roughness. Resistiuities as low as 3.5 microhm-cm (2.3 x bulk resistiuity) were measured for relatively thick films (20,000). THIS investigation was undertaken to explore the problems and film characteristics associated with the sputtering of aluminum. Earlier work reported on aluminum sputtering has stressed the contamination of both the cathode and film as well as abnormally low deposition rates.' Data on sputtering yields,3 however, indicate that aluminum sputtering could be practical. Recently, it was shown by Theuerer and Hauser3 that aluminum sputtering was feasible in a conventional oil-diffusion pumped vacuum system provided an inner "getter sputtering" enclosure was employed to minimize gaseous contamination. This technique employs the getter action of aluminum to produce extremely low reactive gas partial pressures in the deposition zone. Aluminum films have already found use in solid-state electronic devices such as transistors and integrated microcircuits. To the present time, most aluminum films have been prepared by evaporation due to the ease with which this metal can be evaporated. Controlled sputtering of aluminum offers a number of advantages over evaporation, however, such as 1) manufacturing compatibility with other metals which must be sputtered, 2) better control of process variables resulting in more repeatable and uniform films, 3) generally better adhesion resulting from higher-energy metal atoms, 4) built-in material supply for continuous operation, and 5) the ability to deposit alloys. The data presented in this paper are the result of two separate studies. One study utilized a small "getter sputtering" enclosure (System A) and was concerned with the structure and properties of thin aluminum films up to about 1600A thick. In this thickness range, study of the film structure was possible with transmission electron microscopy. The second study was conducted with a conventional diode sputtering apparatus (System B) and covered $ much wider range of film thickness up to about 34,000A. Emphasis was placed on developing techniques which would extend aluminum sputtering to an existing in-line continuous deposition process.4 I) EQUIPMENT AND PROCEDURE System A. Fig. 1 shows a schematic of the "getter sputtering" inner chamber used and Fig. 2 is a photograph of this chamber mounted on an 18-in. access ring of a standard liquid-nitrogen trapped bell-jar vacuum system. This chamber was designed after a similar system used by Theuerer and auser.3 The configuration allowed the glow to emanate in all directions from the cathode. Argon (99.99') was allowed to enter only at the top of the chamber such that most of the reactive gases entering with the argon were reacted with the aluminum vapor and deposited on the chilled walls of the chamber before reaching the deposition zone. Provision was also made as shown, Fig. 1, for heating and cooling the substrate from about 20" to 400°C. Two substrate materials were used: Corning 7059 glass (12 by 12 by 0.048 in.) and carbon films about

Jan 1, 1967

By A. F. Peterson, A. R. Eshbach

Much has been written to explain decreasing profits in American industry. Foreign competition, the attitude of government, rising tax burdens and increased labor costs have been blamed in turn. Whatever the cause, management in the mining industry, as elsewhere, is increasingly aware of diminishing profit margins. A mine operator is usually unable to do much about the causes of decreased profits, even if he knows what they are, but he can check the trend in part by cutting the cost of operation. To do this, he must know what his costs are, which of them are most significant and then go about reducing them in a systematic and logical manner.

Jan 10, 1962

By Herbert Hoover

THE desire of the engineers over the last few years, growing out of their contact with public affairs, that this Institute should take a wider vision than the narrower field of technology and should apply its skill to the development of civic problems which must lay in their foundation on engineering, has led to this discussion today. Some of us in San Francisco, in discussing this question of the relation of the engineers to civic problems, raised the question as to whether or not in this national emergency it was not the duty of the Mining Engineers to bring, forward their combined skill and knowledge and experience to bear upon the problems of the coal industry. This industry, considered as a whole, is one of the worst functioning industries in the United States. It is equipped with capital, with machinery, plants and labor to a peak load at least 20 per cent. above the average necessity. This peak load, therefore, involves the use of probably 100,000 men diverted from other productive industries; it involves an intermittency of employment through its whole personnel that results not only in a long train of human woe, but results also in a higher cost of coal -to the general public. The problem of whether the industry can, by any device, be cured or even partially cured of its intermittency, is solely an engineering problem. It is therefore an apropos problem for this Institute. Your President and myself and others thought that we could best develop this discussion by calling upon men of large experience in the particular branches of the soft coal industry, to bring the facts in front of this general committee, with a view to an exhaustive discussion and perhaps subsequently the appointment of a committee to formulate those facts and such remedies as may be developed into a report that would be of constructive value.

Jan 3, 1920

By Vito J. Colangelo

The primary object of this study was to determine the effect of ferrite and its orientation upon the mechanical properties of a precipitation -hardening stainless steel with particular attention to the short-transverse properties. The investigation consisted of Jour major parts : the preliminary investigation of billet properties, the effect of forging reduction and ferrite content upon mechanical properties, the effect of notch orientation upon impact strength, and the relationship of heat composition to ferrite content. Low ductility and impact strength in the short transverse direction were found to he associated with the orientation and shape of- the ferrite plates. It was also determined that impact strength varied with notch orientation. The test values obtained with the notch perpendicular to the plane of the ferrite plate were lower than those obtained in the notch-parallel condition. The over-all investigation showed that high ferrite contents in general had a deleterious effect upon mechanical properties and that the ferrite content could he minimized by exercising rigorous control of the heat composition. A careful balance of elements, nitrogen in particular, must he maintained in order to reduce the formation of ferrite. THE precipitation-hardening stainless steels were developed to fulfill a need for high-strength corrosion-resistant alloys. In the annealed condition they are soft and ductile and possess many of the desirable characteristics of the austenitic stainless steels. In the hardened condition, the alloys exhibit the high strength and hardness of the martensitic stainless steels. The alloy under consideration in this investigation has a nominal composition as follows: C Mn Si Cr Ni Mo N 0.13 0.95 0.25 15.50 4.30 2.75 0.10 The hardening mechanism is identical to that of other hardenable steels in that it depends upon the transformation of austenite to martensite. This alloy because of its annealed structure and its ability to be hardened combines the desirable forming and corrosion properties of the austenitic grades with the high hardness and strength levels attainable with the hardenable grades. The reason for this apparent duplicity of proper- ties can be explained by considering a basic metallurgical difference between the hardenable stainless steels and those of the austenitic group. Both types are austenitic at 1800°F but, while the martensitic grades transform to martensite upon rapid cooling to room temperature, the austenitic grades remain austenitic even when cooled to temperatures below room temperature. The major difference then is in the degree of austenite stability. This stability can quantitatively be described by the Ms temperature. The Ms is defined as that temperature at which austenite begins to transform to martensite. The austenitic grades for example may be cooled to -300°F without producing significant quantities of martensite. The hardenable stainless steels on the other hand have an Ms temperature in the vicinity of 400" to 700°F. In cooling to room temperature, these alloys traverse the entire Ms-Mf range and show almost complete transformation to martensite. The semiaustenitic stainless steel, however, occupies an intermediate position with respect to its austenite stability. The analysis is so balanced that the Ills temperature lies at or slightly above room temperature. The resulting alloy retains much of its austenite at room temperature and yet responds to hardening heat treatments. Achieving this delicate balance of elements is therefore of great importance. Slight imbalances of the equivalent Cr-Ni ratios frequently result in the presence of 6 ferrite. It is the effects of this ferrit with which we are concerned, more specifically the effect of the quantity and ferrite orientation upon mechanical properties, particularly ductility. PROCEDURE A) Preliminary Investigation of Billet and Forging Properties. In order to determine the effect of ferrite on billet properties, billet stock from three heats with various ferrite contents was utilized. Tensile specimens were obtained in the transverse and longitudinal directions from this material and heat-treated as shown in Tables I and 11. Forgings were made from these same heats, the purpose being to determine what effect, if any, the ferrite might have upon the mechanical properties. These forgings were made in such a manner as to elongate the ferrite in the longitudinal and transverse directions. The method of forging was as follows. A section was cut from a 6-in.-sq billet of Heat A and flat-forged to 1-1/2 in. thick. Working was done from one direction only with no edging passes as shown

Jan 1, 1965

By Walter R. Hibbard, Robert I. O’Herron, Fred D. Rosi, Howard T. Clark

INTRODUCTION AND PREVIOUS WORK IN the search to find a copper-base alloy with high strength properties, it was considered that the addition of a small amount of an age-hardening element to a binary system with useful strength properties might result in a series of alloys of theoretical and practical importance. [ ] The copper-nickel system was selected for its basic properties and chromium was added as the age-hardening element in view of the small percentage involved and its decreasing solubility with decreasing temperature. A study of the Cu-Cr binary alloys was undertaken as a preliminary investigation. However, in view of the response of these alloys to heat treatment, the scope of this phase of the investigation was widened. [ ]

Jan 1, 1948

To Install Waste Heat Boiler at White Pine White Pine Copper Co.'s smelter 18 miles southwest of Ontonagon, Mich., will have a six story high boiler utilizing what otherwise would be waste heat from a copper reverberatory furnace. Designed and under construction by the Babcock & Wilcox Co., the boiler will supply steam to a turbo-generator furnishing power for the projected development. The boiler will be in line with and following the reverberatory furnace. Using waste heat from the furnace in place of fuel for steam generation, about 50 pct of heat in the fuel originally supplied to the furnace will be recovered by the waste heat boiler. Exploration conducted over the past 15 years at White Pine, wholly owned subsidiary of Copper Range Co., has disclosed reserves of 309 million tons averaging 21.3 lb of copper per ton. Ore mineral is chiefly chalcocite (Cu2s).

Jan 5, 1953

By AIME AIME

POSSIBILITY of a greatly increased manganese production from domestic source; is indicated by news that the Bureau of Mines has been successful in producing concentrates with high manganese content from the low-grade deposit, in the Las Vegas, Nev.) area. The first unit of the comprehensive group of pilot plants built by the Bureau of Mines at Boulder City, Nev., under a defense appropriation has started operations, demonstrating definitely the applicability of a process developed in the Bureau laboratories. About 12 1/2 lb. of manganese is needed for the production of every ton of steel, and substitution is difficult. The United States produces only about 3 per cent of its total needs of this ore. Only high-grade ore, such as the Russian ore, containing 18 per cent or more manganese, is generally used by American producers in making ferro¬manganese the form in which manganese is usually added in steel manu-

Jan 1, 1941

By Henry Rawdon

Cold-working is generally considered as a process of hardening metals. Diamet-rically opposite statements concerning the applicability of the scratch-hardness method in the testing of cold-worked metals, particularly after severe deformation, which exist in the technical literature led to the study of the results which are summarized in this paper. A series of metals, of which copper, iron and tin are used as illustrations here, were cold rolled to a definite degree without any intermediate annealing and the hardness determined by both the scratch and Brinell methods. The results indicate that the metal hardens rapidly during the initial stages of deformation; however, after a certain stage, which corresponds to a rather definite microstructure, the metal becomes softer and in its final form may be softer than the metal in its initial stage. As part of the study of the scratch-hardness method for metals and alloys in cooperation with one of the technical committees of the American Society for Testing Materials, the authors devoted considerable time to the study of the changes in hardness of metals when cold rolled. Various seemingly contradictory statements in the technical literature concerning the applicability of the scratch-hardness method to such cold-rolled materials were among the principal reasons for the investigation, the results of which are in part presented here. The effect of cold deformation, at least in moderate degrees, on the hardness as measured by the Brinell and other common methods is so well known that further reference is unnecessary. Concerning the scratch hardness of cold-worked metals, Martens and Heyn state' that hardness, whether measured by the ball-pressure method (Kugeldruck) or by the scratch method (Ritzverfahren), will be increased by cold deformation. Jeffries and Archer give a seemingly diametrically opposite view. They state,2 that "the sclerometer (indicating scratch

Jan 1, 1924

By J. S. Vanick

AN extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applica-tions requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small-grain grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By G. K. Manning, A. R. Elsea, A. B. Westerman

A considerable number of high-tem-perature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. .4t the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in vitalliurn after various heat treatments. Howcver, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chro-mium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja and Guertler2 indicated that cobalt and chro-mium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to 85 pct chromium undergo a transformation at [zoo to 12 50 c More recently, Wever and Haschimoto,3 Wever andLange,4and Matsunaga5 carried Out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallogra~hic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Mat-SUnaRa. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these excep-tions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data arid the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitalhum by deter-mining the diagram for the cobalt-chro-mi~m system- Experimental Work For the convenience Of the reader, the diagram as determined by the present investigation is presented in Fig 3. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the melting point for pure chromium is the

Jan 1, 1949

By Henry Mulryan

Diatoms are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skelctons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. Diatomites Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. Diatoms More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the freshwater diatomites on the Pacific Coast are: Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralfs Diatoma vulgare Dory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kützing Stictodiscus niagarac Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg Epithemia turgida Kützing

Jan 1, 1942

By Henry Mulryan

Diatoms are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skelctons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. Diatomites Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. Diatoms More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the freshwater diatomites on the Pacific Coast are: Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralfs Diatoma vulgare Dory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kützing Stictodiscus niagarac Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg Epithemia turgida Kützing

Jan 1, 1942

By L. R. Duncan, O. M. Wicken

Magnesium, the eighth most abundant element in the earth's crust, is found widely distributed in a variety of minerals. Among the more commercially important ones are magnesite (MgCO3), brucite (Mg[OH]2), dolomite (CaMg[C03]2), and the salts magnesium sulfate and chloride often found in natural brines. Among other commercially important magnesium-containing minerals are olivine ([MgFe]2Si04), talc (H2Mg3[Si03]4), and serpentine (H4Mg3Si2O9). These are valuable because of desirable characteristics given them by the magnesium content and its placement in the particular crystal structure. These minerals are the raw materials for a host of products including magnesium metal and several grades of magnesia or magnesia-containing materials for refractories, fluxes, fillers, insulation, cements, decolorants, fertilizers, and chemicals. Considering only those minerals valued for their magnesia or magnesium content, over 85% of the material tonnages are processed to be used as refractories. Dolomite, which is used in enormous tonnages for its physical properties in construction, has an important use as a refractory raw material in its own right and, after calcination, as a precipitant for magnesium hydroxide, which is an intermediate for the production of magnesia or magnesium metal. Magnesia from the reaction of calcined dolomite (or limestone) with seawater or magnesium-containing brines has supplanted much of the production of magnesia from mined magnesite, particularly in the United States. The best known of the minerals directly and widely exploited for magnesia content is magnesite, one of the calcite group of rhombohedral carbonates which includes calcite (CaC03), siderite (FeCO3), and rhodochrosite (MnCO3) among others. The members of this group enter into a wide range of substitutional solid solutions when the positive ions have similar radii. The radii of magnesium and iron ions are within 6% of each other; hence, magnesite and siderite form a complete series of which breunnerite (ferroan magnesite) is a well-known end member. However, the radius of calcium ion is 36% larger than that of magnesium ion, and only limited substitution exists at each end of the MgCO3-CaCO3 series. Dolomite is not a member of the calcite group, but results when calcium and magnesium ions alternate in equal number in an ordered structure among carbonate ions. The result of these relationships is that calcite and dolomite, often found intermixed with magnesite, occur commonly as identifiable crystal entities which can often be separated to a varying degree from the magnesite by various beneficiation techniques. Magnesite, when pure, contains 47.8% MgO and 52.2% CO.. The pure mineral is sometimes, but rarely, found as transparent crystals resembling calcite, but, preponderantly, magnesite contains variable amounts of the carbonates, oxides, and silicates of iron, calcium, manganese, and aluminum. Magnesite may be either crystalline or amorphous (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black with shades of yellow, blue, red, or gray. The color is not a fundamentally significant indicator of purity, but in a given deposit, an experienced person can often roughly grade magnesite by assessing color and crystallinity. The crystalline form of magnesite occurs in

Jan 1, 1983

By H. C. Chang, N. J. Grant

REEP studies and measurements in most in-V> stances are based on a relatively gross gage length. Even in some recent theoretical studies on the mechanism of creep, changes were followed by means of X-rays and metallography without regard for the behavior of the individual grains and grain boundaries.'" Analytical studies of creep have frequently indicated that more than one competing process is operative and that the ultimate creep performance depends on the effects of temperature, time, and strain rate as well as grain size.'-" he grains and grain boundaries are known to respond differently to these variables but the extent of the response is still little known, especially in poly-crystalline materials where the relative orientations of grains and grain boundaries are important. This paper reports some experimental observations of the behavior of the grain boundaries and their effect on the deformation in the grains. High purity aluminum was used to avoid complications of aging reactions, second phase, inclusions, etc. Experimental Procedure A small vertical nichrome wound furnace was built to permit direct loading on the test specimen. This furnace is capable of operating up to about 1300°F with reasonable temperature distribution. A ground rectangular quartz window, 1.25x0.5 in., is imbedded in the external stainless steel tube to permit observations of the creep process with a microscope. An argon atmosphere ,was provided to prevent oxidation. The quartz window caused a temperature gradient between the back and front surfaces of the specimen of 15" at 700°F. The temperature gradient could be cut down to 3°F along the length of the specimen by adjusting shunts across the furnace windings. An ordinary metallurgical microscope with a working distance of 14 mm was rebuilt so that it could be moved in three mutual perpendicular directions. Visual examination could be made with either a 30X eyepiece or a 15X filar eyepiece. Using an objective of focal length 24.3 mm and a numerical aperture 0.20 a total magnification of 120X or 240X could be obtained. High purity aluminum rated at 99.995 pct was supplied by the Aluminum Co. of America as % in. then the gage portion was further machined to 3/16 in. diam. The ends were Y4 in. diam and threaded to fit available specimen holders. Two opposite flat surfaces of the gage portion were obtained by milling, giving final dimensions of the gage portion of 3/4x3/16x3/32 in. Machined specimens were first electropolished in Jacquet's solution.' Reference marks were produced by pressing a thin sewing needle into the surface of the specimen. The specimen was then annealed at 900°F for 24 hr and at 1150°F for 12 hr. Typical macrostructures of specimens treated in this manner are shown in Fig. 1. The range of the grain size was 1 to 5.5 mm (see Fig. l), but most of the grains were of 2.5 mm and went through the whole thickness of the specimen. The specimen was re-electropolished and etched electrolytically to reveal the grain boundaries. In order to reveal the orientation difference of the grains, etch pits were produced on the surface of the grains by etching in a mixture of hydrochloric and nitric acids (HC1, 45 pct; HNO,, 10 pct; H,O, 45 , by volume). The specimens were very carefully put into the holders and furnace; yet even with this care, fine slip lines were developed on the specimen surface.

Jan 1, 1953

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By E. Hoek

INTRODUCTION Rock slope stability research has been in progress for the past four years at the Royal School of Mines in London under the sponsorship of a consortium of 23 companies* with interests in open pit mining. This paper reviews the principal aims and achievements of this research project. In order to assist the reader in following these details, the basic philosophy underlying the formulation and direction of this research project is discussed. DISTRIBUTION OF RESPONSIBILITY In open pit mining, the economic necessity of keeping waste rock removal to a minimum generally means that the mine slopes have to be excavated to the steepest possible slope angle. On the other hand, excessive steepening of these slopes can induce failures, which may negate the economic benefits that have been aimed at and which may also result in loss of life and damage to equipment. Consequently, where slope failures are likely to prove to be a problem, an evaluation of the stability of the slopes to be created should be included as part of the overall pit design. How is the stability of a rock slope evaluated? When this question was examined, during discussions on the research policy to be followed at the Royal School of Mines, it was clear that relatively few satisfactory techniques were available in a form that would be comprehensible and therefore useful to the practical mining engineer. It was recognised that the research project must be directed towards two distinct aims: a) The evaluation of existing techniques for rock slope stability analysis and the provision of new techniques where these existing methods were found to be inadequate and b) The presentation of the results of this evaluation and research in a form that would be useful to engineers without specialist training in rock mechanics. It was soon realized that a university based research team, however large and efficient, could not achieve these aims without the co-operation and assistance of mining engineers,

Jan 1, 1972

By A. J. Opinsky

THE purpose of this note is to indicate the locations and sizes of various interstitial holes in the orthorhombic uranium lattice based on a hard-sphere model. First, plane configurations of three and four atoms will be examined, and then the true interstices surrounded by four atoms in space and by five atoms in space will be obtained. The data and notation contained in a report by Tucker' will be used. Plane Configurations Fig. 1 presents the orthorhombic uranium lattice made of spheres touching at the closest interatomic distance. The three light-colored spheres in the ab plane are illustrative of the first type of configuration to be examined. If one edge of the unit cell is taken as the origin, the three atoms can be represented by the vectors [Oi + Oj + Ok], [ai + Oj + Ok] and [(a/2)i + (b/2)j + Ok] where i, j, and k are respectively parallel to a, b, and c. In the future, this notation will be shortened to [000], [a00] and [a/2 b/2 0], respectively. A vector R = [r s t] de-scribes the position of the hole surrounded by the atoms. Since the center of the hole must be equidistant from the three atoms R2 = r2 + s2 + t2 = (r-a)2 + s2 + t2 = (r-a/2)2 + (s-b/2)2 + t2. R = [a/2 (b/4) - (a2/4b) 0] is the solution of these

Jan 1, 1955