Search Documents

By T. B. Counselman

WHEN one thinks of Minnesota iron ore, one thinks of big open pits, where high- grade ore is simply scooped up with a power shovel, loaded into cars, and hauled away for shipment to the blast furnace. On the western end of the Mesabi range, however, are large tonnages of iron ore which contain too much silica to be used directly in the blast furnace, and these ores must first be concentrated to a purer form. The Mesabi range is about 100 miles long and a maximum of 3 miles wide. The iron formation, which in its unaltered form is called taconite: consists of a banded iron- bearing chert. Where the high-grade ore bodies occur, these have resulted from folding and cracking with sub- sequent leaching out of the silica, leaving the iron oxide behind. The big open pits and the underground mines are situated in these concentrations.

Jan 1, 1941

By B. A. Cheadle, K. P. Steward

Axial tensile, ring tensile, closed end burst, and free end burst tests were done at room tempe.vature and 300°C on three batches of Zircaloy-2 sheathing zuith different textures. Knoop hardness tests were also done on all batches. The mechanical properties of the tubes were largely dependent on the percentages of cold work, but were also markedly affected by the textures, particularly with respect to deformation behavio'r. The deformation behavior observed confirmed Picklesimer's predictions, zuhereas Knoop hardness results could be correlated with texture and yield strength anisotropy after the ,method of Wheeler and Ireland. From the mechanical properties, and from efjectiue strain values deterrlzined at the fractures using a photoqid technique, it zuas concluded that tubing witlz a single preferred orientation of radial basal poles best combines strength and ductility for any given deqee of cold work. THE mechanical properties required in collapsible Zircaloy-2 fuel sheathing for water-cooled power reactors are strength to resist wrinkling deformation by coolant pressure and ductility to accommodate a small amount of deformation in service without rupturing. Zircaloy-2 tubing during fabrication develops pre- ferred orientations of the a Zr grains due to aniso-tropic deformation behavior, and these textures markedly affect mechanical properties. Picklesimer' had predicted the deformation behavior of tubes with various textures, but the texture required to provide the optimum strength and ductility for a given degree of cold work has not been reported. To investigate this problem, tests at three transverse to axial stress ratios were done at room temperature and 300°C on three batches of Zircaloy-2 tubing covering a wide range of textures and percentages of residual cold work. Knoop hardness values were also measured to correlate with preferred orientation and yield strength anisotropy after the method of Wheeler and relland.' 1) MATERIAL For this investigation, three batches of tube-reduced tubing were chosen from the Zircaloy-2 sheathing produced for the Douglas Point Reactor. Individual tubes were 191/2 in. long, 0.600 in. OD, and 0.0165 in. nominal wall thickness. The identities of the batches, together with their textures, are shown in Table I. The tubes had the normal Zircaloy-2 composition3 of 1.5 wt pct Sn, 0.3 wt pct Fe, Ni, Cr combined with the following oxygen concentrations: Batch VII 1140 to 1390 ppm 0 Batch VIII 1400 to 1750 ppm 0 Batch IX 880 to 1320 ppm 0

Jan 1, 1968

By E. S. Leaver

THE amount of gold that occurs in a ton of milling ore from most of the large-scale copper mines is so small that unusual care and special attention are necessary to recover it. In some cases the gold is not considered important enough to warrant daily assays of the various products. Considering the large tonnage of copper ores that are now concentrated by flotation, as computed in a recent review, the gross gold content is surprisingly large, probably amounting to over 10 million dollars per year in the United States. The indications are that in many of the copper-milling operations with gold content under $1 per ton, only 50 per cent. of the gold is recovered in the flotation concentrates. Lime is generally used as a depressant for pyrite in the flotation circuit. The authors have shown that high lime or a solution high in calcium ions is also a depressant for gold. Their experiments on several well-known ores show that by careful regulation of the alkalinity of the mill solutions, a higher flotation recovery of the gold can be obtained, together with equally good copper recovery in a good grade of copper concentrates. In cyanidation for the recovery of gold, the best accepted practice demands that the mill solutions be tested and regulated by simple chemical reactions at definite periods during treatment or with each change in the treatment. It is similarly important for the recovery of gold that the solution in the flotation circuit be analyzed for calcium ions at regular periods and at each step in the flotation practice. The lime should be added when and where needed and not in excessive amounts at the head of the mill.

Jan 1, 1931

By John Wulff, David A. Stevenson

The rates of solution of copper, nickel, and three copper-nickel alloys in liquid lead were studied at 527° and 727°C under dynamic conditions. The relative velocity at the solid-liquid interface was varied from 8.65 to 125 cm per sec. Analysis of the data for the pure metals indicates that the solution rate is transport corztrolled at lower velocities, but a transition to mixed control occurs at higher velocities, higher temperatures, and higher percent saturation. 1 HE present work concerns the effect of relative velocity at a solid-liquid interface on the dissolution kinetics of pure solid materials in liquid metals. This general problem is of interest in electrode kinetics, in electrolytic processes, and more recently in the field of liquid metal corrosion. Considerable work has been done on dissolution kinetics in aqueous environments because of the obvious importance to electrolytic processes.1,2 In purely metallic systems investigation has been more limited. There are, of course, extensive data from loop tests which are used in an engineering evaluation of liq- uid metal corrosion. Here, however, the dissolution process is complicated by several interdependent processes. In general, one of two factors is considered to be rate limiting in the dissolution process: the transport of material from the solid-liquid interface into the bulk liquid, or an activation process directly at the interface. A number of studies of the dissolution rates of solid metals in liquid metals under static conditions have been published.3- Since the attendant hydrodynamic conditions imposed by thermal gradient convection and concentration gradient convection are difficult to analyze, it is doubtful if a clear interpretation of the experimental findings of these papers in terms of the mechanism involved in the dissolution process can be made. A clearer picture of the dissolution process is provided by

Jan 1, 1962

By Jerome Alexander

The object of this paper is to show that many of the important phenomena of metals and alloys are due to the facts that, at some stage, metals and alloys, or some of their constituents, are in a colloidal state and that a portion of the metal or alloy tends to remain in this state. The so-called amorphous phase in pure metals is an isocolloid, consisting of colloidal groups of metal molecules that may be dispersed in still more finely subdivided metal; these colloidal particles are not truly amorphous, but may consist, in part, if not entirely, of ultramicroscopic crystals; as a result the expressions amorphous phase and amorphous theory might he replaced by the expressions colloidal phase and colloidal theory. Any substance is in the colloidal state when the constituent particles consist of molecular or atomic groups, whose size varies approximately from about 100 down to about 5pp, that is from just below the limit of microscopic resolvability to the dimensions commonly ascribed to the larger molecules. Colloidality involves no assumption as to the shape, internal structure, or orientation of the colloidal particles; size alone is the critical factor. A colloidal system may therefore contain crystalline groups, or amorphous groups (non-crystalline, random or haphazard clusters), or a mixture of the two. All colloids consist of at least two phases, the subdivided substance, or dispersed phase, and the substance into which this is subdivided, the dispersion medium. It is not necessary that there be any chemical difference between the dispersed phase and the dispersion medium. As molecular forces are extremely powerful, their application may produce marked changes in the physical properties of metals. It is doubtful whether metal in the interior, especially of large masses, possesses the same properties as that on or near the surface, which alone is open to inspection.

Jan 1, 1921

By Dave H. Barnett, Brij M. Moudgil

The flotation technique as employed by Florida phosphate producing companies for the beneficiation of fine phosphate particles has been standardized over the years. Lower recoveries of coarse phosphate rock by froth flotation technique, however, led to the development of new methods based on skin flotation of phosphate agglomerates. Recent developments of floating coarse rock in large flotation machines have not yet convinced the rock producers of their higher separation efficiency. It is interesting to note that the selection of a particular machine is still based on equipment preference by an individual company as well as proven performance of a particular machine for upgrading a specific material. Various techniques which have been developed to beneficiate the coarse phosphate rock have been discussed. Performance of the individual techniques is presented.

Jan 1, 1980

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not so much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solu-tions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensi-tive to long contact with material such as sand grains or attached bar-nacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direc-tion of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as character-istic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears prac-tical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment of the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By J. L. Huiatt, G. M. Potter, R. B. Tippin

The US Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. have developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 6% K2O. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgS0, 2.7Hp0) and schoenite KeS0,MgS04.6H,0), were conditioned in a saturated brine solution., thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular-weight fatty acid. Continuous small-scale pilot-plant testing indicated that 80% of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 13% K2O.

Jan 1, 1976

By E. H. Sellards

Phosphate rock like other mineral substances is found in nature in varying degrees of purity.

Jan 1, 1915

By N. H. Fisher

GEOGRAPHICAL DISTRIBUTION THE most important known deposits in Australia of what are commonly referred to as the beach-sand minerals are along the most easterly part of the Australian coast, between Southport, 17 miles north of the Queensland-New South Wales border, and Ballina, 50 miles south of the border, and most of the production has come from this area (Fig 1). Smaller deposits are known to occur farther to the south at intervals for several hundred miles, and beaches have been worked at Yamba, 96 miles south and Woolgoolga, 150 miles south of the border and at Swansea, 60 miles north of Sydney. Important deposits have been shown to exist on north Stradbroke Island and others have been located farther to the north, as far as Tin Can Bay at the south end of Frazer Island. (Fig 2). Table I gives the list of operators with the location of their deposits and workings, their approximate maximum monthly capacity expressed in tons of heavy mineral produced by their concentrating plants before separation into individual mineral concentrates, their methods of mining and concentrating the minerals, and the products obtained. This table applies as of June 1948, but all the operators are remodeling or improving their plants and plant practices will be modified accordingly. In addition, active boring campaigns have been carried out by Alluvial Gold, Ltd., of Sydney, in the Cudgen-Cudgera area, and by Zinc Corporation. Ltd., of Melbourne, on Stradbroke Island, and in other places. PHYSIOGRAPHY Submergence of the order of 100 to 200 ft at the close of the Pleistocene period left the pre-existing hills as promontories and the valleys as deep inlets. Wave action has built bay-bars and sandspits in a northerly direction from the headlands, and lakes and marshes have formed between these bars and the initial post-submergence coast line. These lakes and swamps have been or are being filled in by river-borne sediments or wind-blown sand. Beasley1 has presented evidence that suggests a recent emergence of the coast line of about 10 ft. The evidence for this belief is the presence of a black sand seam 1/3 mile inland and 17 ft above sea level (Fig 3), and although it is not entirely certain that this seam is of beach formation and owes nothing to windblown concentration, other evidence supports the suggestion of recent emergence. Such emergence would undoubtedly aid the formation of bars and sandspits and the easterly progress of the beach front, leaving a series of parallel dunes (Fig 4). This belt of north-south coastal dunes ranges up to 1/2 mile in width and as many as 15 lines of dune have been counted (Fig 3). The foredune is generally the highest, up to 25 ft high, and there is in many places a flat platform in front of the dune known as the berm. The dunes behind the foredune are lower and less well defined

Jan 1, 1947

By W. S. Ayres

The construction of a new breaker at the Cranberry Colliery, Hazleton, Pa., was forced upon the operators, A. Pnrdee & Co., by a fire which destroyed the entire plant early in January, 1896. The loss included, in addition to the breaker, three boilerhouses and three engine-houses. The boilers were not injured, but the steam-pipes and connections were all broken and warped by the fire. The boilers were probably saved from injury by the presence of mind of the fireman., who started all his feed-pumps and filled the boilers with water. The hoisting-engines were more or less warped and cracked, but by patching and replacing the injured and broken parts, they were made to do satisfactory service in the new plant. It may be worthy of mention that the wrought-iron shaft of one of the hoisting-drums, 12 inches in diameter by 17 feet long, was so heated in the fire that the weight of the drum caused it

Jan 1, 1899

By Carl Henrich

Aspen, the flourishing mountain- and mining-town of Pitkin county, Colorado, is located in the valley of the Roaring Fork, 11 miles above Glenwood springs, where that stream empties its waters into Grand river, a tributary of the Colorado. The Roaring Fork heads on the western slope of the Sawatch range near Grizzly peak, and runs in a general northwesterly direction to its junction with the Grand river. Of its numerous tributaries, Castle creek joins it just below the town of Aspen, the town being built on an extensive flat hounded on the northeast by the Roaring Fork and on the west by Castle creek. The latter heads at the junction of the Sawatch and the Elk mountains and flows northward between the two chains, until it empties into Roaring Fork. Opposite the town of Aspen, Hunter creek, coming westward from the western slope of Mount Massive, joins the Roaring Fork. About a mile north of Aspen, the bed of Hunter creek is at least 300 feet higher than that of the Roaring Fork at Aspen. Hunter creek forms thus, at its mouth, one of the best water-powers in Colorado. A portion of it is now utilized for electric lighting in Aspen, while in the near future, the whole of this magnificent natural power will be applied, through electric transmission, for hoisting, pumping and ventilating at different mines of the district. The mountain opposite the town of Aspen, on the east side of Hunter creek (which near its mouth flows southerly), is called Smuggler mountain, from the famous mine at the foot of it. On the other, or western, side of Hunter's creek (see map, Fig. I), a higher mountain rises, on the slope of which the regular dip of the Triassie or Upper Carboniferous red sandstone strata, alternating with white layers of the same rock, can be clearly seen from town. This mountain is called Red mountain, from the prevailing color of its rocky

Jan 1, 1889

By Robert Uhley, Tsvi Meidav, LeRoy Scharon

Before National Lead built an industrial plant on its Fredricktown property, some 100 miles south of St. Louis, a 750x500-ft area on the proposed site was investigated by electrical resistivity, seismic refraction, and churn drilling. Data were accumulated to prepare an isopach map of the overburden and to determine soundness of the dolomite bed- rock and the depth to bedrock at fixed points. The site was on a gently sloping hillside. Elevations above sea level ranged from 760 ft in the northwest corner to 820 ft along the eastern edge, giving a total relief of 60 ft. There were no major drainage features, but in the northern part of the plant site there was an indicated depression area which later was interpreted as reflecting subsurface conditions in the bedrock. No rock was exposed in the entire plant site area; the surface was characterized by soil and overburden.

Jan 2, 1959

By A. Cochardt, D. H. Feisel

HE success of the sintered aluminum powder material (SAP)' in raising the maximum useful temperature of aluminum alloys has stimulated effort in investigating similar systems in which the metallic matrixes have higher melting points. Examples of such systems which have been studied are nickel-alumina,2, 3copper-silica,4 copper-alumina,4 titanium-cerium oxide,5 and 80/20 nickel-chromium,8 cobalt,= and molybdenum7 matrixes with various hardeners. Conventional precipitation-hardened high-temperature alloys are often thermally unstable in service. The original fine particles that are responsible for good strength properties grow in size at elevated operating temperatures, a process termed "over-aging." This growth of precipitated particles causes a gradual loss in strength properties. A previous paperb describes the factors that govern the process of overaging, and estimates the time required for overaging of a nickel-alloy matrix dispersion-hardened by various precipitates such as are found in current high-temperature alloys, and by alumina. These calculations indicate that nickel-base alloys hardened with Ni3Al, Tic, or TiN are quite unstable at 1340" F (727°F). Such alloys should overage within a few hours at that temperature. A nickel-base alloy hardened with alumina, on the other hand, should behave differently. It should not overage appreciably within a thousand years. It was further shown8 that the thermal stability of the oxide-hardened alloy is mainly due to the low solubility of oxygen in equilibrium with alumina in the nickel-base matrix. Since the oxygen solubility is small, little oxygen can diffuse, and structural changes require very long times. This paper illustrates the effects of time and temperature on the structural stability of nickel alloy matrixes hardened by dispersions of Ni3A1, Ni3Ti, Tic, and alumina, and of nickel-chromium matrixes hardened by alumina. Hardness measurements and metallography have been used as a measure of structural stability. EXPERIMENTAL PROCEDURE Using the best information from published phase diagrams,'-l4 compositions of the Ni-Al, Ni-Ti, and Ni-Ti-C alloys were determined so as to have 5 vol pct of precipitate at 1350° F(732°C), the temperature selected to illustrate the effect of time on structural stability. Table I lists the chemical compositions of these alloys. Standard laboratory melting and alloying techniques were used in preparing ingots of the F-Series of alloys. The cast ingots, 1 3/4 in. in diam, were forged to 3/8-in. diam rods.

Jan 1, 1960

Jan 11, 1950

By J. E. Spurr

Jan 1, 1903

Jan 1, 1924

By E. M. Furness, A. S. Henderson

ORIGINALLY the Babbitt experimental plant grinding circuit consisted of one rod mill 10 ½ ft diam by 12 ft long in open circuit followed by two ball mills 10 ½ ft diam* 12 ft long in parallel circuit. Shortly after operations commenced it was apparent that the rod mill could not function satisfactorily at the required 125 gross tons of ore per hr. Attempts to operate at this rate produced: 1) excessive tramp material over rod mill trommel screen which could not be handled in this open circuit and 2) excess build-up of coarse ore in the ball mill circuits because of inadequate rod mill grinding. Since Reserve Mining Co. ore must be ground to 85 pct -325 mesh to produce a satisfactory iron concentrate, an efficient and controlled grinding circuit is highly important. The first step in trying to resolve this grinding problem was to determine which unit of the circuit was actually in trouble and to what extent. A series of tests conducted at a lower tonnage rate of rod mill feed indicated that one ball mill could grind satisfactorily at rates up to 70 gross tons of rod mill feed per hr.

Jan 12, 1957

By Wilfred Walker

With the advent of the New Global Tectonics a coherent pattern of geology is emerging. To the economic geologist this is of vital concern because the type of mineralization in particular environments is predictable. Developments in geological reasoning now take their place beside developments in geochemistry and geophysics. Much is known of the worldwide geography of the Alpine orogenic period because it is now ending its 200 million years of existence, starting with the Jurassic, and we can see the mid-ocean rises and the down flow zones, and between them the stable oceanic and continental platforms. The concepts of mantle cells, the spreading sea floor, and continental drift have gained general acceptance. The oceanographers have demonstrated the uprises like that in the mid-Atlantic. In this paper it is suggested that down flows in the oceans are marked by island arcs, like the West Indies; and down flows in the continents are marked by orogens like the American Cordillera. The number and position of mantle cells is controversial: a total of about 16 cells is suggested in this paper. Certain cells expand, and as they carry continents with them give rise to concepts of plate tectonics. Specific types of mineral deposits are associated with the uprises, oceanic and continental platforms, and down flows. The uprises are accompanied by the currently described Red Sea and Salton Sea deposits, the oceanic parts of the platform have the nodular deposits, and the continental platforms have the post-tectonic deposits. However, most economic metal deposits are associated with the down flow zones in which the stage of geosynclinal development controls the type of deposit: (1) In the initial development stage the simatic upper mantle may be tapped and give rise to the volcanogenic massive base metal sulfide deposits and to the ophiolite suite which characteristically carries nickel, chrome, and cupreous pyrite. (2) In the early geosynclinal stage sialic crust is driven down into the simatic magma of the upper mantle and basic to acidic differentiates give rise to stocks accompanied by skarn and hydrothermal deposits. (3) The intermediate stage of geosynclinal development gives rise to tin-tungsten, lithium, and beryllium deposits as the magma chamber rises above the level of the upper mantle and there is no simatic component. (4) The late stage is one of regenerated deposits. The porphyry deposits are not restricted to stages but only by the time of generation of acid magma. As the geosynclinal system dies, the mantle is again the source of magma, giving rise to gabbro and diabase dykes and sills: in this last, post-tectonic, continental platform environment are found the Mississippi Valley type lead-zinc deposits, the Blind River and Witwatersrand type of sedimentary uranium and gold deposits, and also Sudbury's nickel. The key relationship of major ore deposits generated by downflows is depicted herein on a framework of uprises, platforms, and downflows in the Alpine orogenic period. There is evidence for nine orogenic periods, of which the Alpine period is the latest, having taken place from 3500 million years ago to the present. Each period was characterized by its own worldwide mantle cell system and associated uprises, platforms, and down flows. The cycle of geosynclinal development, including corresponding cycles of mineralization, can be precisely defined in relation to each of these orogenic periods. The development of the Alpine orogenic period therefore can be used as a guide to the study of the earlier orogenic periods which comprise well known periods: Kenoran, Hudsonian, Grenville, and Paleozoic; and less well known: Konkian, Aulian, Belomorian, and Elsonian [(Table 1)]. Each name is used for the period as a whole, and not for the main orogenic event.

Jan 1, 1973

By David Mandolesi

An examination has been made of the structures of strand cast blooms and the rails rolled from them; this paper details the characteristics of these typical structures. Results of mechanical testing data show that this product compares with rails processed from conventional ingot steel. Improvement in processing yields and surface quality standards are also briefly discussed.

Jan 1, 1972